Database Users

isdn > linux-pbx > SIP > BT-Bridge > XDA2

Hi,
today i received my first ISDN call on my MDA2
- get you ISDN-Card working under Linux
- install asterisk
- install bluez
- install brctr
- BluetoothGPS.cab
- install X-Lite on the XDA2
Code:
/etc/asterisk/modem.conf
[interfaces]
context=remote
driver=i4l
stripmsd=1
dialtype=tone
mode=immediate
msn=YourMSN
device => /dev/ttyI5
/etc/asterisk/sip.conf
[general]
[olli]
type=friend
username=olli
host=dynamic
canreinvite=no
add somthing like:
exten => 500,2,Dial(SIP/olli)
[from-sip]
exten => olli,1,Dial(SIP/olli)
exten => olli,2,Hangup
in the /etc/asterisk/extensions.conf
Give the XDA a static IP and connect to the
Bluez(0) Network Accesspoint.
Than configure the BT-Bridge:
Code:
modprobe usb-uhci
modprobe uhci
modprobe usbcore
mount /proc/bus/usb/
modprobe bluez
modprobe l2cap
modprobe bnep
modprobe sco
modprobe rfcomm
modprobe hci_usb
hcid
sdpd
pand -s -r NAP -M
ifconfig eth0 down
ifconfig eth0 0.0.0.0
ifconfig bnep0 0.0.0.0
brctl addbr pan0
ifconfig pan0 192.168.1.19
brctl addif pan0 eth0
brctl addif pan0 bnep0
route del default
route add default gw 192.168.1.1 dev pan0
brctl showmacs pan0
ping the XDA.
Install X-lite
configure:
user: olli (see sip.conf)
sip-proxy: IP of the astrisk server
mark sent internal IP
Now your can receive IP and PSTN calls.
PSTN by dialing your MSN+500 from any phone.
Has anybody an idea how to configure asterisk
to forward SIP-Calls from the xda to PSTN ?
bye Olli

The XDA a static IP and connect to the
Bluez Network Accesspoint. how is the other?
_________________
Ip pbx

Cannot map to a Samba Share, but xp notebook can?

Hello,
Problem: Cannot get my pda (HTC Mogul) to connect to a samba share.
Behavior: Resco File Explorer (V7.03) keeps asking for a password when I try to map to a samba share.
Basic Setup Information:
ROUTER: Dynamic Type Configuration acting as a DHCP Server. The DNS is Automagic from the IP.
LAPTOP (windows xp): 192.168.1.38 / 255.255.255.0
SAMBA_PC (Suse 11) : 192.168.1.36 / 255.255.255.0
PDA (Sprint Mogul, Windows Mobile 6 Pro): 192.168.1.37 / 255.255.255.0
-----Below is my current smb.conf---------------
# smb.conf is the main Samba configuration file. You find a full commented
# version at /usr/share/doc/packages/samba/examples/smb.conf.SUSE if the
# samba-doc package is installed.
# Date: 2008-06-07
[global]
workgroup = MCHOME
printing = cups
printcap name = cups
printcap cache time = 750
cups options = raw
map to guest = Bad User
include = /etc/samba/dhcp.conf
logon path = \\%L\profiles\.msprofile
logon home = \\%L\%U\.9xprofile
logon drive = P:
usershare allow guests = Yes
use spnego = No
[homes]
comment = Home Directories
valid users = %S, %D%w%S
browseable = No
read only = No
inherit acls = Yes
[profiles]
comment = Network Profiles Service
path = %H
read only = No
store dos attributes = Yes
create mask = 0600
directory mask = 0700
[users]
comment = All users
path = /home
read only = No
inherit acls = Yes
veto files = /aquota.user/groups/shares/
[groups]
comment = All groups
path = /home/groups
read only = No
inherit acls = Yes
[printers]
comment = All Printers
path = /var/tmp
printable = Yes
create mask = 0600
browseable = No
[print$]
comment = Printer Drivers
path = /var/lib/samba/drivers
write list = @ntadmin root
force group = ntadmin
create mask = 0664
directory mask = 0775
[linuxpodcasts]
comment = downloaded shows
inherit acls = Yes
path = /home/jason/Podcasts/
read only = No
[lacie]
comment = storage drive
inherit acls = Yes
path = /media/disk/
read only = No
------------------------------------------
PDA TESTING:
1) Ping \\LINUX-PD\lacie
Results: 24.A.B.C
Note: this number is unknown. It is only similar to the Router Configuration in the first number!
2) Ping 192.168.1.36
Results with Reply from 192.168.1.36
3) Ping \\LAPTOP
Results 24.A.B.C
Note: This is the same number as PDA Testing #1
-------------------------------------------
LAPTOP TESTING:
------------------------------------------
1) Ping \\LINUX-PD
Results: 24.A.B.C .Qu1nnLAN
Note: This is the same number as PDA Testing #1 including the name of the wireless lan!
2) Ping 192.168.1.36
Results with reply from 192.168.1.36
3) Ping 192.168.1.37
Results with reply from 192.168.1.37
4) net view \\LINUX-PD
<< shows all of the shares , Not Shown, The Command Completed successfully >>
5) net use g: \\LINUX-PD\lacie
<< asks for username / pass. The Command Completed successfully >>
6) From File MANAGER, I can sucessfully browse the network and view the shares!
From XP > Command Prompt: ipconfig /all
Windows IP config:
Host Name: LAPTOP
Primary DNS Suffix:
Node Type: Unknown
IP Routing Enabled: NO
WINS Proxy Enabled: NO
DNS Suffix Search List: Qu1nnLAN
...
Ethernet adapter wireless Network Connection
Connection Specific DNS Suffix: Qu1nnLAN
...
Connection
DHCP Enabled: Yes
Autoconfig Enabled: Yes
IP Address: 192.168.1.38
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
DHCP Server: 192.168.1.1
DNS Servers: 24.W.X.Y
24.W.X.Z
------------------------------------------
LINUX-PD TESTING: (Includes steps from Chapter 38 of the Samba Checklist)
------------------------------------------
1)
Ping 192.168.1.37
Results in Reply form 192.168.1.37
2)
linux-pd:~ # smbclient -L LINUX-pd
Enter password:
Domain=[MCHOME] OS=[Unix] Server=[Samba 3.2.0rc1-22.1-1795-SUSE-SL11.0]
Sharename Type Comment
--------- ---- -------
profiles Disk Network Profiles Service
users Disk All users
groups Disk All groups
print$ Disk Printer Drivers
linuxpodcasts Disk downloaded shows
lacie Disk storage drive
IPC$ IPC IPC Service (Samba 3.2.0rc1-22.1-1795-SUSE-SL11.0)
Photosmart_3200 Printer Photosmart 3210
HIDDEN Disk Home Directories
Domain=[MCHOME] OS=[Unix] Server=[Samba 3.2.0rc1-22.1-1795-SUSE-SL11.0]
Server Comment
--------- -------
LAPTOP Pentium M750 1.86GHz, 1GB RAM
LINUX-PD Samba 3.2.0rc1-22.1-1795-SUSE-SL11.0
Workgroup Master
--------- -------
MCHOME LINUX-PD
3)
linux-pd:~ # nmblookup -B LINUX-PD __SAMBA__
querying __SAMBA__ on 127.0.0.2
192.168.1.36 __SAMBA__<00>
4)
linux-pd:~ # nmblookup -d 2 '*'
added interface eth0 ip=fe80::213:20ff:fecb:7cbb%eth0 bcast=fe80::ffff:ffff:ffff:ffff%eth0 netmask=ffff:ffff:ffff:ffff::
added interface eth0 ip=192.168.1.36 bcast=192.168.1.255 netmask=255.255.255.0
querying * on 192.168.1.255
Got a positive name query response from 192.168.1.36 ( 192.168.1.36 )
192.168.1.36 *<00>
5)
linux-pd:~ # smbclient //LINUX-PD/lacie
Enter HIDDEN password:
Domain=[MCHOME] OS=[Unix] Server=[Samba 3.2.0rc1-22.1-1795-SUSE-SL11.0]
smb: \>
6)
linux-pd:~ # nmblookup -M MCHOME
querying MCHOME on 192.168.1.255
192.168.1.36 MCHOME<1d>
-------------------------------------------
Additional Questions:
1) how do you find the machine name on the PDA similar to how the LINUX-PD = 192.168.1.36?
2) why is the wireless router name showing up when I ping?
I am at a loss.
I will be posting to a Resco forum as well.
Any suggestions helping this newb would be great.
Thank you for your time
qu1nn
_______________

same problem here. did u fix it?

I got it working, albeit Resco doesnt remember the password correctly and it has to be entered in every time I start a new session.
make note and read before you read the next thread....
that resco is aware of the issue:
http://resco.net/pocketpc/explorer/faq.asp?faq=network#85
Check out my posting on rescos forums for what I had to do:
http://resco.net/forums/ShowPost.aspx?PostID=17810
I hope this helps
qu1nn

[How to] Change DNS server on Android phones

Domain Name System / Server is the one which takes care of translating the human readable domain names into machine understandable IP addresses. If you are not able to access a particular set of websites either from your laptop /phone, DNS server could be a reason for it. To fix the problem, one has to change the network configurations to use some of the popular DNS servers like Open DNS or Google’s public DNS. On Android phones, changing the DNS server is easy if you are using the static IP. You can do it from Settings > Wireless & network settings > Wi-Fi settings > Advanced (from menu) > check the ‘Use static IP’ option. After that, you will be able to change the DNS servers. However, when you are using dynamic IP (which will be the case most likely), the process is not straight forward. DNS server details will be taken from the DHCP server which assigns the IP.
Here are the steps to be followed to change the (WIFI Connection) DNS servers:
- Android system chooses the DNS servers using the script located at “/system/etc/dhcpcd/dhcpcd-hooks/20-dns.conf”
- By default, /system partition is mounted as read-only. Need to re-mount the same in re-write mode.
- Take a backup of the script. Download the modified version of the script from here (http://varun-scratchpad.googlecode.com/svn/trunk/static/20-dns.conf). The modified script has two additional lines which will override the DNS server changes. The modified script uses the Google’s public DNS.
- Changes will be applied after restarting the connection /device.
3G Connection:
- Download the wrapper script from here (http://varun-scratchpad.googlecode.com/svn/trunk/static/change-dns.sh) This wraps all the commands needed for changing the DNS server in a shell script.
- Download and install an interpreter for executing your shell script from your phone (e.s. scripter from Rom Toolbox)
- Launch the script. Grant the Super permission when asked.
- You just have to run this script whenever you are connecting to your mobile network.
Done. You settings are proper by visiting http://welcome.opendns.com. Remember, the settings will be applicable only for the current session.
By: http://blog.varunkumar.me/2010/09/how-to-change-dns-server-on-android.html?m=1

Or use Set DNS from Market

lol.. I cover my head with ashes!!!
I didn't know about these apps... I apologize!!!

uffapple said:
lol.. I cover my head with ashes!!!
I didn't know about these apps... I apologize!!!
Click to expand...
Click to collapse
your work isn't useless.. it tell me how it work.. thanks

Help
Help, after i did this i can't connect to Wi-Fi anymore. I copied the old 20-dns file and nothing u_u. Pls help

Override DNS for KitKat
uffapple said:
Domain Name System / Server is the one which takes care of translating the human readable domain names into machine understandable IP addresses. If you are not able to access a particular set of websites either from your laptop /phone, DNS server could be a reason for it. To fix the problem, one has to change the network configurations to use some of the popular DNS servers like Open DNS or Google’s public DNS. On Android phones, changing the DNS server is easy if you are using the static IP. You can do it from Settings > Wireless & network settings > Wi-Fi settings > Advanced (from menu) > check the ‘Use static IP’ option. After that, you will be able to change the DNS servers. However, when you are using dynamic IP (which will be the case most likely), the process is not straight forward. DNS server details will be taken from the DHCP server which assigns the IP.
Here are the steps to be followed to change the (WIFI Connection) DNS servers:
- Android system chooses the DNS servers using the script located at “/system/etc/dhcpcd/dhcpcd-hooks/20-dns.conf”
- By default, /system partition is mounted as read-only. Need to re-mount the same in re-write mode.
- Take a backup of the script. Download the modified version of the script from here (http://varun-scratchpad.googlecode.com/svn/trunk/static/20-dns.conf). The modified script has two additional lines which will override the DNS server changes. The modified script uses the Google’s public DNS.
- Changes will be applied after restarting the connection /device.
3G Connection:
- Download the wrapper script from here (http://varun-scratchpad.googlecode.com/svn/trunk/static/change-dns.sh) This wraps all the commands needed for changing the DNS server in a shell script.
- Download and install an interpreter for executing your shell script from your phone (e.s. scripter from Rom Toolbox)
- Launch the script. Grant the Super permission when asked.
- You just have to run this script whenever you are connecting to your mobile network.
Done. You settings are proper by visiting http://welcome.opendns.com. Remember, the settings will be applicable only for the current session.
By: http://blog.varunkumar.me/2010/09/how-to-change-dns-server-on-android.html?m=1
Click to expand...
Click to collapse
Thank you for sharing, but I have to say that the "setprop" method does not work on KitKat (I'm talking about mobile connections).
I wrote an app called "Override DNS for KitKat" to solve this issue. It's on the Play Store.

There's a much more reliable and easier method. Just use this as AFWall custom script or use manually in init.d (replace '$IPTABLES' with 'iptables' and just use the last 2 lines).
Code:
$IPTABLES -t nat -D OUTPUT -p tcp --dport 53 -j DNAT --to-destination 208.67.222.222:53 || true
$IPTABLES -t nat -D OUTPUT -p udp --dport 53 -j DNAT --to-destination 208.67.222.222:53 || true
$IPTABLES -t nat -I OUTPUT -p tcp --dport 53 -j DNAT --to-destination 208.67.222.222:53
$IPTABLES -t nat -I OUTPUT -p udp --dport 53 -j DNAT --to-destination 208.67.222.222:53

DualJoe said:
There's a much more reliable and easier method. Just use this as AFWall custom script or use manually in init.d (replace '$IPTABLES' with 'iptables' and just use the last 2 lines).
Code:
$IPTABLES -t nat -D OUTPUT -p tcp --dport 53 -j DNAT --to-destination 208.67.222.222:53 || true
$IPTABLES -t nat -D OUTPUT -p udp --dport 53 -j DNAT --to-destination 208.67.222.222:53 || true
$IPTABLES -t nat -I OUTPUT -p tcp --dport 53 -j DNAT --to-destination 208.67.222.222:53
$IPTABLES -t nat -I OUTPUT -p udp --dport 53 -j DNAT --to-destination 208.67.222.222:53
Click to expand...
Click to collapse
The "iptables" commands also works good on my Nexus 4 and Slimkat, thank you!

[Guide] Mac Spoofing / Changing

After reading several posts on mac spoofing and having failed to find a working thread.I decided to fill in the gaps with my linux knowledge (however little of that I may have).
So this method seems to solve some issues I've seen (MAC not changing because device wasn't downed) in these threads:
http://forum.xda-developers.com/showthread.php?t=1385577
http://forum.xda-developers.com/showthread.php?t=902354
without editing the nvram.txt
I've tested the ip link method on my recently rooted Samsung Tab 2 7.0"
Changing your mac address:
Prerequisites:
*A rooted device
*Busybox
*Terminal emulator
*Turn wifi on from your device's menu, do not connect to any network.
*Open your terminal emulator, now type:
$su
#ip link
*This should list all networking interfaces, identify your wifi device, take note of the name. now:
#ip link set NAME down
#ip link set NAME address 00:11:22:33:44:55
#ip link set NAME up
I believe that when using ifconfig the procedure is as follows:
$su
#ifconfig
*Take note of the device name
#ifconfig NAME down
#ifconfig NAME hw ether 00:11:22:33:44:55
#ifconfig NAME up
After doing the above you can connect to the desired network normally, using the default / other user interfaces.
NOTE: The mac address will be reset when WIFI is switched off.
I have confirmed the ip link method to be working. i.e. transmitted mac address is the new / changed one!

Actually in my case (SGS) i had to restart wifi first and then (while it's starting) quickly change the MAC using:
Code:
busybox ifconfig wlan0 hw ether 00:11:22:33:44:55
Important: It must be done about 500ms after enabling wifi, otherwise it won't work.
If I change MAC when wifi is off it simply returns to the original during next start.
Worked on i9000 with CM9 / 10

pawci0 said:
Actually in my case (SGS) i had to restart wifi first and then (while it's starting) quickly change the MAC using:
Code:
busybox ifconfig wlan0 hw ether 00:11:22:33:44:55
Important: It must be done about 500ms after enabling wifi, otherwise it won't work.
If I change MAC when wifi is off it simply returns to the original during next start.
Worked on i9000 with CM9 / 10
Click to expand...
Click to collapse
So downing the interface before changing and uping afterwards doesn't work?

i want to learn well the mac spoofing

setoPul Wilcox
this is actually incredibly useful, I got MACblocked off a network near college. thanks!

Doesn't work for me
Code:
# su
# ifconfig tiwlan0 down
# ip link set tiwlan0 address 00:11:22:33:44:55
ip: SIOCSIFHWADDR: Operation not supported on transport endpoint
# ifconfig tiwlan0 hw ether 00:11:22:33:44:55
error: SIOCSIFADDR (Invalid argument)
I guess its a kernel/driver problem... at least I know it works on normal Linux systems.

Itcouldbeyou said:
Doesn't work for me
Code:
# su
# ifconfig tiwlan0 down
# ip link set tiwlan0 address 00:11:22:33:44:55
ip: SIOCSIFHWADDR: Operation not supported on transport endpoint
# ifconfig tiwlan0 hw ether 00:11:22:33:44:55
error: SIOCSIFADDR (Invalid argument)
I guess its a kernel/driver problem... at least I know it works on normal Linux systems.
Click to expand...
Click to collapse
Funny that only some manufacturers disable such features. You could always try editing the nvram file? I haven't tried it though.

Isnt it dangerous ?

Script to apply random mac
I've made a script to create a random ghost mac every time I run it on the terminal emulator with su.
Code:
macaddr="52:54:$(dd if=/dev/urandom count=1 2>/dev/null | md5sum | sed 's/^\(..\)\(..\)\(..\)\(..\).*$/\1:\2:\3:\4/')"
ip link set wlan0 down
ip link set wlan0 address $macaddr
ip link set wlan0 up
I've named it as gmac.sh and saved it on /sdcard/, thus by running:
Code:
$ su
# sh /sdcard/gmac.sh
the mac is changed.
Regards :cyclops:

Works differently on HTC Desire
Hello,
This is just to "set in stone" somewhere in the Internet that on some devices, you need *not* to down and up the network interface. Otherwise, the network driver will restore its MAC address from hardware/driver settings.
On a HTC Desire, MAC spoofing works this way:
* turn on the wifi interface using the standard Android interface
* run this script :
Code:
macaddr="52:54:$(dd if=/dev/urandom count=1 2>/dev/null | md5sum | sed 's/^\(..\)\(..\)\(..\)\(..\).*$/\1:\2:\3:\4/')"
ip link set wlan0 address $macaddr
Best regards,

On some devices (e.g. HTC Desire among others), the wifi GUI still resets the mac address even with the method described in this thread.
worstenbrood has modified the wifi driver so that the mac address can be configured from a text file. It is described here:
http://forum.xda-developers.com/showthread.php?t=1525230
This is compatible with the wifi GUI and solves the problem of the wifi interface reloading its original mac address.
Anyone interested, I have backported his modifications to the latest state of the kernel developement in CM7.
thanks!

I get a 'operation not supported on transport endpoint' error when running the 'ip link set wlan0 address 00:11:22:33:44:55' and a about the same error with busy box.

Thanks for this! Gonna try this later.

damien.courousse said:
Hello,
This is just to "set in stone" somewhere in the Internet that on some devices, you need *not* to down and up the network interface. Otherwise, the network driver will restore its MAC address from hardware/driver settings.
On a HTC Desire, MAC spoofing works this way:
* turn on the wifi interface using the standard Android interface
* run this script :
Code:
macaddr="52:54:$(dd if=/dev/urandom count=1 2>/dev/null | md5sum | sed 's/^\(..\)\(..\)\(..\)\(..\).*$/\1:\2:\3:\4/')"
ip link set wlan0 address $macaddr
Best regards,
Click to expand...
Click to collapse
anyone help me mine Hcl me 2G 2.0 i can't change mac please help me....

[Q] adhoc network problem

I have android 4.2.2 ,Nexus 4 I would like to setup adhoc network . Firstly I rooted the device, secondly I tried to create adhoc network in android phone : I create ad hoc network in an android smartphone like below:
[email protected]:/ # ip link set dev wlan0 down
[email protected]:/ # iwconfig wlan0 mode ad-hoc
[email protected]:/ # iwconfig wlan0 channel 6
[email protected]:/ # iwconfig wlan0 essid 'Test1'
[email protected]:/ # ip link set dev wlan0 up
[email protected]:/ # ifconfig wlan0 192.168.65.129
when I typed iwconfig wlan0: the result is:
Qcom:802.11n ESSID:"Test1"
Mode:Ad-Hoc Frequency:2.437 GHz Cell: 02:82:5F:C1:4B:C1
Bit Rate=0 kb/s Tx-Power=0 dBm
RTS thr=2347 B Fragment thr=8000 B
Encryption keyff
Secondly, in my laptop ,I could see "Test1",so I did connect to "Test1" and I configure static ip address 192.168.65.128. in this case ,the smartphone create the ad hoc network and my laptop join it,then I can ping from my laptop to mobile and vice-versa.
However,in other case when : my laptop create ad hoc network
and later in an android mobile ,I tried to join it :
[email protected]:/ # iwconfig wlan0 mode ad-hoc
[email protected]:/ # iwconfig wlan0 channel 6
[email protected]:/ # iwconfig wlan0 essid 'Test1'
But,when I type iwconfig wlan0 ,essid still off/any
Qcom:802.11n ESSIDff/any
Mode:Ad-Hoc Frequency:2.437 GHz Cell: Not-Associated
Bit Rate:0 kb/s Tx-Power=0 dBm
RTS thr=2347 B Fragment thr=8000 B
Encryption keyff
it seems that android mobile can create ad hoc network but can not join existing one.so the same result I found when I try to setup adhoc network between two android mobiles. can anybody tell me what it's wrong here,and if there is any possible solution.
I tried many methods to setup ad hoc network in android ,and only this method that it seems work,but it still something wrong that prevent android phone to join existing ad hoc network.

fadwa.ww said:
[email protected]:/ # iwconfig wlan0 mode ad-hoc
[email protected]:/ # iwconfig wlan0 channel 6
[email protected]:/ # iwconfig wlan0 essid 'Test1'
Click to expand...
Click to collapse
Did you forgot to execute "ip link set dev wlan0 up"?