Related
OK guys im really screwing my Nook Color up. First I used the size specific images for my 4gb sandisk and the lastest cm7 nightly still zipped up moved over. Booted to what I assume is CWM on the SD card and installed however instead of Installing the CM7 to the SD it over wrote the Nooks internal memory!!!! I got the stock image back on there then found this thread....
Everytime I try to use that loader it partitions my SD card to 107mbs and there seems to be nothing I can do about it. What am I doing wrong? I have my stock image restored but I think im missing a step to just put the OS on the SD and boot from the SD card so I can tinker....
thanks
Shawn
This was just discussed in another thread.
http://forum.xda-developers.com/showthread.php?t=1192704
If you downloaded the correct "generic-sdcard" image file from verygreen, I doubt that you can install it into the internal memory since it's fully automatic and require no human finger touches/presses anything except power the Nook back on.
You must have downloaded a wrong file.
If you asked about why your "boot" is only 117MB then the answer is simple, because it is what it is and it is normal. The rest of your 4GB uSD is still unallocated and needs to be enable to use.
Problem: ClockworkMod not booting from MicroSD card
What I'm trying to do: Dual-boot CyanogenMod 7 with the stock Nook Color with Cyanogen 7 on a MicroSD card, but without rooting the Nook Color.
What I've done so far:
1. Downloaded ClockworkMod 3.2.0.1 from download.clockworkmod.com/recoveries/recovery-clockwork-3.2.0.1-encore.img
2. Downloaded Win32DiskImager from launchpad.net/win32-image-writer/trunk/0.3/+download/win32diskimager-RELEASE-0.3-r27-binary.zip
3. Using Win32DiskImager, flashed ClockworkMod onto the MicroSD card.
4. Ejected MicroSD card.
5. Inserted MicroSD card into Nook Color (which is turned off)
6. Connected Nook Color to PC via USB cable
7. Powered on Nook Color
8. Watched as standard Nook Color boots. Nothing at all displays related to ClockworkMod.
Other troubleshooting thus far
a. I've gone back to step 3, used Windows 7 to just format the SD card to ensure it was blank, and then started with Step 3 again.
b. I've ensured the MicroSD card is set properly into the Nook Color.
c. I've tried holding down the power key on the Nook Color (no effect).
d. Searched these forums via its Search function, and searched via Google (most references use ClockworkMod 3.0.2.8, which a few posts mention does not work on the "blue dot" version of Nook Color.
Misc:
MicroSD card: SanDisk Type-2 4GB
Nook Color (the "blue-dot" version that starts with a 1GB partition for side-loading)
PC: Windows 7 64-bit, built-in SD card reader/writer
Any help or guidance would be greatly appreciated. Thank you.
Ynglaur said:
Problem: ClockworkMod not booting from MicroSD card
What I'm trying to do: Dual-boot CyanogenMod 7 with the stock Nook Color with Cyanogen 7 on a MicroSD card, but without rooting the Nook Color.
--- SNIP ---
Any help or guidance would be greatly appreciated. Thank you.
Click to expand...
Click to collapse
If all you're trying to do is setup a bootable SD card with CM7 on it, and retain the ability to also boot to the stock Nook ROM, try this:
http://forum.xda-developers.com/showthread.php?t=1000957
Based on "What I'm trying to do" and "What I've done so far", you are heading to the completely wrong direction.
A good thing is you had not been able to get into CwM Recovery, otherwise, you made a mess of your NC.
Just stop "what you've done so far" and follow the link that shumash provided above.
shumash said:
If all you're trying to do is setup a bootable SD card with CM7 on it, and retain the ability to also boot to the stock Nook ROM, try this:
http://forum.xda-developers.com/showthread.php?t=1000957
Click to expand...
Click to collapse
Agreed, you don't need clockwork mod for an SD card install. Follow the directions in my signature (adds some details that verygreen leaves out).
Installing image for CM7
I have a nook color that was purchased just a week ago and had 1.4.0 firmware on it. I had updated it to 1.4.1 before noticing that this particular firmware blocked the nook from being hacked. I had read in one of the threads how to revert back to 1.4.0, adding acclaim.zip file to the sd card would do the trick. I tried this and when my nook went to sleep, nothing. I ended up using the nook-complete-restore-1.0.1.zip with a clockworkmod recovery file and followed steps provided in other threads. Then I was stuck at the "n" screen and could not get any further. With an additional 8 Factory resets and doing the complete restore a second time I was able to get back to what I believe is factory. The difference is, out of the box I had 1.4.0 and now I have 1.3.0. I believe this is fine.
I am wanting to put CM7 with google apps on my nook. I have read a thread that suggested putting an agnostic size image file and when used, my 16gb sd card went down to >200 mb. What is a good image file to use for my card or what am I doing wrong? I am using Win32DiskImager to write my images. I have tried generic-sdcard.img for both 1.1 and 1.3 and the above still happens. I loose over 14gb of space.
I have downloaded the following to use once I have figured out what image to use. update-cm-7.1.0-encore-signed.zip for my CM7 and gapps-gb-20110828-signed.zip for my google apps.
Thanks for all the hard work that is put into making our nook experience the best!!!
dhed73 said:
[...] The difference is, out of the box I had 1.4.0 and now I have 1.3.0. I believe this is fine.
Click to expand...
Click to collapse
If you're installing CM anyhow, the version of B&N running is not important, correct.
I am wanting to put CM7 with google apps on my nook. I have read a thread that suggested putting an agnostic size image file and when used, my 16gb sd card went down to >200 mb.
Click to expand...
Click to collapse
Going by that name, you were doing a CM install to SD. If you'd completed that process, it would have made use of the rest of your SD card.
What is a good image file to use for my card or what am I doing wrong?
Click to expand...
Click to collapse
Are you trying to:
1. Root stock (doesn't sound like it)
2. Install CM to SD for dual boot
3. Install CM to eMMC
I have downloaded the following to use once I have figured out what image to use. update-cm-7.1.0-encore-signed.zip for my CM7 and gapps-gb-20110828-signed.zip for my google apps.
Click to expand...
Click to collapse
You might want to check out CM 7.2 RC0 Mirage (search here). It incorporated all of the fixes and some optimizations up through CM n253.
I am wanting to install CM to SD for dual boot. I have completed the process for adding the image to my card. The problem is that, after adding the image I now have 115mb on my 16gb card. If, I go ahead and install to my SD card will the space on the card be opened up or do I have to do something else?
dhed73 said:
I am wanting to install CM to SD for dual boot. I have completed the process for adding the image to my card. The problem is that, after adding the image I now have 115mb on my 16gb card. If, I go ahead and install to my SD card will the space on the card be opened up or do I have to do something else?
Click to expand...
Click to collapse
If you're getting that 115mb number from your PC card reader on Windows, that's misleading because that's just the size of the boot partition. There are other partitions on the card that take up space and are formatted to be used by CM7. Boot into CM7 on the SD card and see how much space you've got on the /sdcard partition. It should be many gb.
To see how the card is partitioned and the sizes in Windows, get Easeus Partition Master. It's free. If the last partition (the 4th) isn't fully allocated, use Easeus to do it. Don't resize any of the other partitions until you really know what you're doing.
shumash said:
If you're getting that 115mb number from your PC card reader on Windows, that's misleading because that's just the size of the boot partition. There are other partitions on the card that take up space and are formatted to be used by CM7. Boot into CM7 on the SD card and see how much space you've got on the /sdcard partition. It should be many gb.
To see how the card is partitioned and the sizes in Windows, get Easeus Partition Master. It's free. If the last partition (the 4th) isn't fully allocated, use Easeus to do it. Don't resize any of the other partitions until you really know what you're doing.
Click to expand...
Click to collapse
I have a issue with downloading cm7 on a sd card ive followed all the steps and boot it and it downloads and restarts and seems to be working but the touch screen isnt working. My nook is version 1.3 any help would be appreciated.
lesdavid said:
I have a issue with downloading cm7 on a sd card ive followed all the steps and boot it and it downloads and restarts and seems to be working but the touch screen isnt working. My nook is version 1.3 any help would be appreciated.
Click to expand...
Click to collapse
I had the same problem when I had to restore my nook color. I ran the program, in my case the nook system restore file, a second time. After I had done this, my touch screen was back working.
---------- Post added at 07:53 PM ---------- Previous post was at 07:48 PM ----------
shumash said:
If you're getting that 115mb number from your PC card reader on Windows, that's misleading because that's just the size of the boot partition. There are other partitions on the card that take up space and are formatted to be used by CM7. Boot into CM7 on the SD card and see how much space you've got on the /sdcard partition. It should be many gb.
To see how the card is partitioned and the sizes in Windows, get Easeus Partition Master. It's free. If the last partition (the 4th) isn't fully allocated, use Easeus to do it. Don't resize any of the other partitions until you really know what you're doing.
Click to expand...
Click to collapse
shumash,
Thanks..... after downloading the easeus partition file I found that you were correct and I had 14gb left over. I had a hard time booting into recovery for the google app file but, it finally happened. I am up and running and want to thank everyone for the help.
gallahad2000 said:
Agreed, you don't need clockwork mod for an SD card install. Follow the directions in my signature (adds some details that verygreen leaves out).
Click to expand...
Click to collapse
Many thanks. The instructions in your signature worked perfectly. Just curious: is there a freeware image-making software app that doesn't expire after 30 days?
Trying to prepare 32gb card for nook cm7
Using verigreen's size agnostic img
Wrote it to the card using win image writer
dropped cm7 and gapps
on boot it recognizes card, makes partitions, inflats stuff everything looks ok
on reboot it does NOT boot from sd
instead goes to nook default
exact same stuff on 8gb card works fine
what gives?
I have two nooks at this point
both may have cwm recovery - i dont know how to check
(I know how to use nook, update it etc, but not sure about this cwr thingy)
one has cm7.1 on emmc
other has nook 1.2 rom on emmc
in both of them if i insert 8/16/32gb card
1) if sd card has fresh verygreen image with update...zip and gapps..zip installer kicks in and preps sd card
2) once i reboot, it ---- does NOT ---- boot from sd card anymore
All I want is bootable sd card with cm7.1 on it so that I can give it to a friend of mine
what am I doing wrong
is there a way to force nook to boot from sd card?
I think if it finds cwr on emmc and cwr on sd, it boots from emmc or something
I use win32diskimager which I think gives more reliable results.
Also you must mount the card in a PC for writing the image using a real USB / SD adapter. Using a card media slot on the PC or using another device like a phone to mount the card are known to give problems.
mrkkk said:
I have two nooks at this point
both may have cwm recovery - i dont know how to check
(I know how to use nook, update it etc, but not sure about this cwr thingy)
one has cm7.1 on emmc
other has nook 1.2 rom on emmc
in both of them if i insert 8/16/32gb card
1) if sd card has fresh verygreen image with update...zip and gapps..zip installer kicks in and preps sd card
2) once i reboot, it ---- does NOT ---- boot from sd card anymore
All I want is bootable sd card with cm7.1 on it so that I can give it to a friend of mine
what am I doing wrong
is there a way to force nook to boot from sd card?
I think if it finds cwr on emmc and cwr on sd, it boots from emmc or something
Click to expand...
Click to collapse
Only put the CM7 zip file on it for the first boot.
use easeus partition software to extend the size of the boot partition to 200 MB after you flash the card with verygreens installer, but before you put cm7 and gapps on there.
I bet you it fails to write the kernel during the install because there is insufficient space - try it again without resizing and pay attention to the readout when it scrolls down the screen, you'll see.
cm7.1 + gapps is almost your whole boot partition, for me it leaves only half a megabyte of free space - that's not enough to unpack and install what's needed.
DizzyDen said:
Only put the CM7 zip file on it for the first boot.
Click to expand...
Click to collapse
hmm, that did it
mrkkk said:
hmm, that did it
Click to expand...
Click to collapse
LOL
Sorry for the OP but also happy for you that your NC is up and running.
I keep saying many times, do it one at a time.
...........
Sorry to bring this thread back but I'm having the same problem using verygreen's tutorial on my NC 1.3. However after booting the NC I get the "cyanogen mod loading..." screen shortly followed by a blank screen (Nook doesn't turn off, though). If I remove the SD card the nook starts up as it normally would.
Followed the advice of these other members (extended partition size to 16gb/16gb, haven't installed gapps either) but I still can't get it to work.
I'm using the latest nightly release of CM7 following the link on verygreen's tutorial released on 11/23. Should I use a stable version instead?
Thanks...
emak212 said:
Followed the advice of these other members (extended partition size to 16gb/16gb, haven't installed gapps either) but I still can't get it to work.
Click to expand...
Click to collapse
There's where you made your mistake. The recommendations of the others on the forum were probably to expand the partition created by verygreen's image to something like 200MB or 250MB. The scripts in the image create and format 3 other partitions in addition to the one created by verygreen's image. When you expanded it to the full size of the SD card there was no room to create the additional partitions.
I would suggest you re-apply verygreen's image, expand it to 250MB and try again.
- Aerlock
Touchscreen Problems
Hello,
I have tried doing this several times, and I get no response from the touchscreen. Everything else works perfectly, but the touchscreen won't respond.
Please help.
Update on Touchscreen Issue
CM7 works fine off the 8GB. Is there something different you have to do to get the 32 to work?
Touchscreen Issue Explained
upthepool said:
Hello,
I have tried doing this several times, and I get no response from the touchscreen. Everything else works perfectly, but the touchscreen won't respond.
Please help.
Click to expand...
Click to collapse
From: Eyeballer:
http://forum.xda-developers.com/showthread.php?t=1030227
****BRAND NEW NOOK COLORS (Dec 2011+/Jan 2012+ are now shipping with a different touchscreen/digitizer (same as used in the nook tablet). As of now this driver is not included in CM7, you are welcome to try to flash CM7, if your touchscreen is unresponsive, restore to stock or flash CM9. CM9 will work as the driver is included.***
It appears that 7.1 works, as well as the most recent nightly from Nov.
I recently installed CM 7 to emmc after running it from sd for a year. When I first did the emmc install I used mirage 3/4 but when 7.2 was released I decided to try it. Now I want to install the new mirage kang but when I copy the file to my sd card it's not there when CWM looks for it. I wiped data and cache but every time I have CWM look for the file to install it only finds CM 7.2. Any thoughts?
I tried to search but not being able to search for exact phrases makes it hard to find anything.
[edit] When I get home I'll try reinstalling from the eyeballer card I made. Should I format my non-recovery sd card? I didn't need to use the eyeballer card to install 7.2. What's going on here?
irisclara said:
I recently installed CM 7 to emmc after running it from sd for a year. When I first did the emmc install I used mirage 3/4 but when 7.2 was released I decided to try it. Now I want to install the new mirage kang but when I copy the file to my sd card it's not there when CWM looks for it. I wiped data and cache but every time I have CWM look for the file to install it only finds CM 7.2. Any thoughts?
I tried to search but not being able to search for exact phrases makes it hard to find anything.
[edit] When I get home I'll try reinstalling from the eyeballer card I made. Should I format my non-recovery sd card? I didn't need to use the eyeballer card to install 7.2. What's going on here?
Click to expand...
Click to collapse
Which SD did you put the mirage file on? If you were still using the SD from your SD install, it is not partitioned right to be using with CWM. CWM is expecting just a plain vanilla SD. You may have the mirage file on partition 4 which CWM cannot see.
It was the card from my sd install but I had formatted it when I originally did the emmc install. Also, I used a different card for the emmc install.
What I don't understand is how I updated to 7.2 by putting the file on the sd card and installing it from CWM but when I did the same thing to install the latest Mirage kang it didn't work. I tried toggling the signed requirement in CWM since Mirage isn't signed but it didn't make any difference. Even now that I deleted data and caches and installed Mirage from CWM card the 7.2 file is still on my main sd card and I can't delete it. Do I need to use the CWM card every time I do an update? Could TiBU be causing this?
irisclara said:
It was the card from my sd install but I had formatted it when I originally did the emmc install. Also, I used a different card for the emmc install.
What I don't understand is how I updated to 7.2 by putting the file on the sd card and installing it from CWM but when I did the same thing to install the latest Mirage kang it didn't work. I tried toggling the signed requirement in CWM since Mirage isn't signed but it didn't make any difference. Even now that I deleted data and caches and installed Mirage from CWM card the 7.2 file is still on my main sd card and I can't delete it. Do I need to use the CWM card every time I do an update? Could TiBU be causing this?
Click to expand...
Click to collapse
Do you have your emmc and SD card swapped in CM? You may think you have it on SD but really have it on emmc. And CWM can't see emmc.
No, at least I didn't set it that way. I skipped that part of mr72's guide. Not only that but I tried putting a copy each on my emmc and my sd and it disappeared from the card and wasn't seen on the emmc.
I redid the whole install earlier. I'm going to try putting a Mirage file on the card now and see if CWM sees it.
irisclara said:
I recently installed CM 7 to emmc after running it from sd for a year. When I first did the emmc install I used mirage 3/4 but when 7.2 was released I decided to try it. Now I want to install the new mirage kang but when I copy the file to my sd card it's not there when CWM looks for it. I wiped data and cache but every time I have CWM look for the file to install it only finds CM 7.2. Any thoughts?
I tried to search but not being able to search for exact phrases makes it hard to find anything.
[edit] When I get home I'll try reinstalling from the eyeballer card I made. Should I format my non-recovery sd card? I didn't need to use the eyeballer card to install 7.2. What's going on here?
Click to expand...
Click to collapse
OP, I've tried to help but really, I can't understand your issue, especially this: "I have CWM look for the file to install it only finds CM 7.2"
What else do you expect it looks for and finds?
Anyway, pls do list as much as info so we can help. I don't want to guess.
1. What is your current system? Is it still running fine?
2. I understand you want to update Cm7. Which version?
3. Since you are running CM7 from eMMC, let just focus on 1 uSD, called "flashable CwM Recovery" uSD. Version 3.2.0.1 is preferred.
4. Do list what else (which files) you have on that uSD. (Using windows)
5. Briefly describe how and what shows on the CwM Recovery window
The more info we gather, the better chance we pinpoint to your problem
update-encore_CM72-MiRaGe-03232012.zip and update-cm-7.2.0-RC1-encore-signed.zip have different file names. When I put the Mirage file on the card CWM doesn't see it. Instead it sees the CM 7.2 RC1 file. That's why I was guessing TiBU, because normally when I flash a file it disappears from the card. I flashed CM 7.2 RC but it won't go away, even if I try to delete it. After conducting the experiment from my previous post I am wondering if my flash card is going bad. I'll do further experiments along that line today.
1. What is your current system? Is it still running fine?
update-encore_CM72-MiRaGe-03232012; occasionally says sd card not installed or available
2. I understand you want to update Cm7. Which version?
I wanted to go to update-encore_CM72-MiRaGe-03232012 which I have now accomplished
3. Since you are running CM7 from eMMC, let just focus on 1 uSD, called "flashable CwM Recovery" uSD. Version 3.2.0.1 is preferred.
yes...
4. Do list what else (which files) you have on that uSD. (Using windows)
I'm not sure I understand what you want here but here's a list of what's on the CWM card: folder (.android secure), folder (Android), folder (DCIM), folder (LOST.DIR),gapps-gb-20110828-signed.zip, mlo, u-boot.bin, uImage, update-encore_CM72-MiRaGe-03232012.zip, update-encore-cwm.emmc-eyeballer.zip, uRamdisk
5. Briefly describe how and what shows on the CwM Recovery window
If you are referring to when I run CWM from this card it installs everything fine.When I wrote this question I was trying to flash the Mirage ROM from recovery and after I selected "install from sd" and "choose which file to install" my only choice was update-cm-7.2.0-RC1-encore-signed.zip rather than the update-encore_CM72-MiRaGe-03232012.zip I expected to see.
Thanks for trying to help. Later today I will try copying my data sd card to another card and see if that fixes the programs saying the card is not available. If it does I will assume the other card is bad. Seem reasonable?
irisclara said:
update-encore_CM72-MiRaGe-03232012.zip and update-cm-7.2.0-RC1-encore-signed.zip have different file names. When I put the Mirage file on the card CWM doesn't see it. Instead it sees the CM 7.2 RC1 file. That's why I was guessing TiBU, because normally when I flash a file it disappears from the card. I flashed CM 7.2 RC but it won't go away, even if I try to delete it. After conducting the experiment from my previous post I am wondering if my flash card is going bad. I'll do further experiments along that line today.
Click to expand...
Click to collapse
a. For less complicated, do just put ONE file in the root folder of your CwMR uSD card, not two. Just put the Mirage there, remove the other.
b. FYI, the latest Mirage is also CM7.2-RC1.
2. I understand you want to update Cm7. Which version?
I wanted to go to update-encore_CM72-MiRaGe-03232012 which I have now accomplished
Click to expand...
Click to collapse
So, you're done? all good? I thought you said you cannot perform the update due to file could be found by CwMR.
4. Do list what else (which files) you have on that uSD. (Using windows)
I'm not sure I understand what you want here but here's a list of what's on the CWM card: folder (.android secure), folder (Android), folder (DCIM), folder (LOST.DIR),gapps-gb-20110828-signed.zip, mlo, u-boot.bin, uImage, update-encore_CM72-MiRaGe-03232012.zip, update-encore-cwm.emmc-eyeballer.zip, uRamdisk
Click to expand...
Click to collapse
Ideally, it should only consist of those files that related for boot such "bold" and those flashable zip files. I don't know why those other folders gotten in there. Have this CwMR card being used on any system as storage b4?
5. Briefly describe how and what shows on the CwM Recovery window
If you are referring to when I run CWM from this card it installs everything fine.When I wrote this question I was trying to flash the Mirage ROM from recovery and after I selected "install from sd" and "choose which file to install" my only choice was update-cm-7.2.0-RC1-encore-signed.zip rather than the update-encore_CM72-MiRaGe-03232012.zip I expected to see.
Click to expand...
Click to collapse
If what you listed on 4) above is all correct, then what you see is the Mirage CM7.2 RC1
Well, I guess I have my answer. I tried to format my 16 GB data card and it wouldn't format. Looks like card failure. Unless someone has a better idea I'm just going to order another card and chalk this up to running the OS off the card for so long. If flash memory only has a limited number of read/write cycles that must have burned through them.
Thanks votinh, leapinlar. Any other advice, suggestions, ideas on the situation will be appreciated.
irisclara said:
Well, I guess I have my answer. I tried to format my 16 GB data card and it wouldn't format. Looks like card failure. Unless someone has a better idea I'm just going to order another card and chalk this up to running the OS off the card for so long. If flash memory only has a limited number of read/write cycles that must have burned through them.
Thanks votinh, leapinlar. Any other advice, suggestions, ideas on the situation will be appreciated.
Click to expand...
Click to collapse
Read/write cycle of the flash devices are usually high, 2000+ time, I doubt that you have burnt through.
Anyway, what tool you use to format your uSD?
---------- Post added at 12:04 PM ---------- Previous post was at 12:01 PM ----------
If I was you, b4 purchasing another card, I would try to reformat the card and re-create its flashable CwMR.
If that didn't help, then order new one but note since you only need it for install ROM, 1GB or 2GB is more than enough.
I want at least a 16 GB card for my data and media. I have a 4 GB that I use for CWM and OS testing. I was using the 16 GB card for my OS when I was running off the card. After I installed to emmc I used the 16 GB card for data. The 16 GB is the card that I was having the problem with at the beginning of this thread. Since then I copied everything except my media onto the formatted 4 GB card and everything is running fine. I tried to format the 16 GB card using HPUSBDiskFormat but I got a message "Cannot Format". What program should I be using to format the card?
Other strange things that make me think the 16 GB card was the problem: I recently put some books on the card but they disappeared, one of my apps that is installed on the card keeps disappearing and I have to reinstall it, picture gallery keeps telling me that it can't read the sd, I can't delete files from the card either on the Nook or on my computer.
I hope it isn't the card and you guys know exactly what the deal is but after I put the 4 GB card in place of the 16 GB those problems aren't happening anymore. The final test will be to put an update file on the 4 GB card and boot to recovery. If CWM can see it I can't see how the 16 GB card isn't the problem.
votinh said:
a. For less complicated, do just put ONE file in the root folder of your CwMR uSD card, not two. Just put the Mirage there, remove the other.
Click to expand...
Click to collapse
I am aware of that but I couldn't get the non-Mirage file to delete. I tried but it wouldn't go away.
b. FYI, the latest Mirage is also CM7.2-RC1.
Click to expand...
Click to collapse
I am aware of this. Mirage has different buttons and other tweaks.
So, you're done? all good? I thought you said you cannot perform the update due to file could be found by CwMR.
Click to expand...
Click to collapse
There's CWM on the card and CWM on the Nook. I could not get CWM on the Nook to see the update file on a non-CWM card. Previously it had. I got it to work by reinstalling from my CWM 4 GB card.
Ideally, it should only consist of those files that related for boot such "bold" and those flashable zip files. I don't know why those other folders gotten in there. Have this CwMR card being used on any system as storage b4?
Click to expand...
Click to collapse
This card was formatted with HPUSBDiskFormat before writing CWM to it.
If what you listed on 4) above is all correct, then what you see is the Mirage CM7.2 RC1
Click to expand...
Click to collapse
I am aware of this. The fact that it wasn't working like that is the reason I started this thread.
Thanks for your help.
Now, it's a bit clearer that you have both CwM Recovery.
As I always mentioned and recommended NOT to flash CwMR into eMMC as it causes more headache than good but still many others choose to go that way and report more issue. Anyway, let's put that aside.
First step, reformat your 16GB card using MiniTools Wizard. I wish you luck there, if it can't, toss the card but if it's OK then second step, create a flashable CwMR 3.2.0.1 and put just the Mirage ROM in there.
I'm sure you know what to do.
Let us know how things go.
I may have done a dumb thing in installing CWM to the emmc but I was following a guide and didn't want to screw anything up. The reason I put off the emmc install for so long is that fear of bricking my Nook. So far so good on that front.
That tip about MiniTools is very helpful. I was sure there was something better than what I was using but I didn't know what it was. So far I'm getting very strange results when trying to format the card. The program says that the format worked but the files are still on the card. Surface test didn't show any errors. I tried to remove the old partition and create a new one but while that appeared to work there was no change on the card. I do notice that it wants to format the card in NTFS but I was under the impression that it should be FAT 32.
Is the card trashed? I can't think of anything else to try. I even flipped the lock switch and checked it. Still can't delete anything. I can't even delete a picture that I put on there.
As a last hope I tried putting the 16 GB card in my camera to see if the camera could format it. No luck. If the camera can't do anything with it the card is dead. Oh well, at least I got all my data off of it.
Votinh, do you know of any guide to removing CWM from emmc? It wasn't the problem in this case but it's not necessary. I didn't really want it but I thought that's how flashing worked on emmc. I see now that I can use ROM Manager for that.
irisclara said:
As a last hope I tried putting the 16 GB card in my camera to see if the camera could format it. No luck. If the camera can't do anything with it the card is dead. Oh well, at least I got all my data off of it.
Votinh, do you know of any guide to removing CWM from emmc? It wasn't the problem in this case but it's not necessary. I didn't really want it but I thought that's how flashing worked on emmc. I see now that I can use ROM Manager for that.
Click to expand...
Click to collapse
Honestly, I chose to never flash CwMR into eMMC so I don't have much experience how to remove it, but I'm sure there is way. Will report back if I stumble across any thread about it. NOTE: having CwMR in eMMC is NOT so bad, it just gets you more headache down the road. A lot of people get it installed.
About your card, it's very itchy, ehhhh
Have you actually hit the format button or done or save whatever? and do so with FAT32, not NTFS.
It's first time I've heard the issue.
Yes, unfortunately. I hit format and then the check mark on the far left which I'm pretty sure is save. It certainly said it was doing something and that it had completed the operation successfully. All the files are still on the card though, after 2 formats, one NTFS and one FAT 32, remove and create, and 1 wipe. The files are all still showing on the card and I can't delete any or add any new.
What brand of your 16GB card is it?
I can't imagine that card was extensive damage like that.
Format many times and files still there, amazing.
The card is a Dane Electric from Newegg. I was surprised that it worked as well as it did for running the OS since it's not a SanDisk.
UPDATE 05/28/13 - Now that verygreen has changed his SD scheme to his new version, this guide should not be used on his ROMs dated 5/27 or newer. Use his new image and follow his new instructions. If you want to see the old instructions click on the Show Content button below.
Click to expand...
Click to collapse
Many users have had difficulty installing the HD+ CM10/10.1 ROMs using the Original/Legacy (verygreen) SD setup (especially Windows users). I have written this guide and have made some tools that should make it easier. No need for ADB or Linux. I have upgraded the CWM (clockworkmod) recovery to version 6.0.2.8 which includes larger fonts, a brighter screen and the ability to use the internal storage for installing zips and performing backups. It also uses verygreen's process from his early4 zip that aligns partitions at 2M. This guide and tools are for the Original/Legacy SD setup by verygreen, not the Hybrid. If you want the Hybrid, go here.
Setting up the SD
Begin by downloading the files you need either with stock or your PC. You will need my updated SD image file, attached below (do not use the early4 image from the verygreen thread), the CM ROM zip you want to install and the gapps zip to match it. Put the last two zips on your internal media sdcard built into the HD+. You can get the HD+ CM10 ROMs here and the HD+ CM10.1 ROMs here. You can get the gapps zips here, 20121011 for CM10 and 20130301 for CM10.1.
Extract the SD image zip and you will have a 117MB .img file. Burn that to your SD with Win32DiskImager in Windows or the dd command in Linux or OSX. The SD needs to be at least 4GB and preferably a SanDisk Class 4.
To use Win32DiskImager, find it on the web (here, it's free) and install it on your Windows PC. Open it (be sure to run it as administrator) and select the drive (device) that has your card reader with your SD inserted. Then in the image file box put the location where you have the extracted img file. Then when everything is set right, click on the write button. A warning will pop up asking if you want to proceed. When you have verified that you are going to write to the correct device, click on Yes. (One user overwrote their external USB hard drive by not verifying first.) If you get an error message about access denied, it means you are looking at the drive with Windows Explorer. Close Windows Explorer and try again. In fact, it is a good idea to close all unnecessary windows when burning, even your browser.
When burning is complete, insert the SD into the Nook and boot. It should boot to the cyanoboot logo and sit there for a little while while it creates the other partitions on the SD and formats CM10SDCARD. Then it will end up in CWM for HD+ Original SD. If it does not leave the cyanoboot logo within a reasonable time (it hangs sometimes), just touch the power key and CWM should come up. To use CWM, press the volume up/down keys to move the cursor and the n key to select an item. The power key is the back button.
Installing ROMs
You can use the "install zip from SD/choose zip from internal memory" option to flash the CM ROM you downloaded earlier to your internal memory sdcard. Then you can flash the right version of gapps to match your ROM.
When you reboot (you need to leave the SD in the slot), the CM ROM should start. You will need to register with Google to set up Play Store.
If you later want to upgrade your ROM to another build, download it to your CM10SDCARD partition using CM. Then boot to CWM and flash it.
Backing Up
This version of CWM lets you back up and restore your setup. You can even back up to internal memory. It does not back up /boot, but does back up /system, /data and /cache.
Swapping EMMC and SDCARD
Some users have installed CM to a small SD card and want their apps to use the large internal media storage to store their data. I have developed a couple of zips to swap EMMC and SDCARD when booted to CM so that internal memory is available to your apps to store their files. One zip will add the swap and one will remove it. Get them attached below.
These zips can be flashed with CWM but will only install to the Original SD with CM. I just fixed a bug in the rev0 and rev1 zips. If you already flashed rev0 or rev1, you need to flash the remove zip before you flash the rev2 fixed version. No need to boot in between.
With rev2, both SDCARD and EMMC will show internal media storage, as will both MTP folders. A new folder, ext_sdcard, will show the external SD media partition.
Updating earlier versions of CWM
Updating prior installs of the Original SD installation to this new version of CWM is easy. Just download the ramdisk zip file attached below and extract the file. Put your old SD setup in your PC and rename the ramdisk.cwm to ramdisk.cwm.bak. Then copy the new ramdisk.cwm you just extracted to the card, replacing the version that was there. Next time you boot to CWM, the 6.0.2.8 version for HD+ Original SD will be there.
Change Log
Change Log
05/28/13 - guide is obsolete starting with the 5/27/13 ROM
05/15/13 - removed warning, resolved
04/10/13 - added warning running CM10.1.
03/09/13 - added rev2 of the swap zip, as it failed on CM10.1
03/08/13 - added rev1 of the swap zip to fix a permissions bug.
03/07/13 - retitled thread
03/03/13 - added CM10/10.1 SDswap zips
02/27/13 - Initial posting
OP Updated
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
For hd plus only?
Sent from my BNTV400 using xda app-developers app
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
mrDAXpax said:
For hd plus only?
Sent from my BNTV400 using xda app-developers app
Click to expand...
Click to collapse
Yes, you can use bokbokan's hybrid image to do it the same way for the HD. And I think his standard image does it too.
Sent from my Nook HD+ running CM10 on Hybrid SD
question...
Sorry if this has been answered somewhere else but, I did this using a 32gb card and everything I running smooth. I have a 64gb card that I want to switch it out for. I know it won't be a problem doing the root and all of that again, but I was wondering if anybody knows how to change the 32gb SD card back to normal? When I stick it in my computer all it shows is the boot partition and when I try to format it, it only formats that's partition. Meaning that my 32gb card turns into a worthless 116 mb card. I've tried on windows and Ubuntu and get the same results...
So does anybody have any suggestion?
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
startoxic said:
Sorry if this has been answered somewhere else but, I did this using a 32gb card and everything I running smooth. I have a 64gb card that I want to switch it out for. I know it won't be a problem doing the root and all of that again, but I was wondering if anybody knows how to change the 32gb SD card back to normal? When I stick it in my computer all it shows is the boot partition and when I try to format it, it only formats that's partition. Meaning that my 32gb card turns into a worthless 116 mb card. I've tried on windows and Ubuntu and get the same results...
So does anybody have any suggestion?
Click to expand...
Click to collapse
Yes, use SDFormatter free from the web. It will do it.
Sent from my Nook HD+ running CM10 on Hybrid SD
Thank you, I will try that and let you know how it works
This is probably a stupid question, but once I've got the SD card set up properly, can I then go ahead and delete the ZIP files that I've installed? Or do I need to keep them kicking around? Figure if I can free up some space, I should.
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
stormerider said:
This is probably a stupid question, but once I've got the SD card set up properly, can I then go ahead and delete the ZIP files that I've installed? Or do I need to keep them kicking around? Figure if I can free up some space, I should.
Click to expand...
Click to collapse
You can delete them if you want, but I usually always keep them somewhere so I don't have to redownload them if I need to reflash, which very oftern I have to for various reasons. I can always delete them later if space becomes an issue.
Sent from my Nook HD+ running CM10 on Hybrid SD
leapinlar said:
You can delete them if you want, but I usually always keep them somewhere so I don't have to redownload them if I need to reflash, which very oftern I have to for various reasons. I can always delete them later if space becomes an issue.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
*nod* I meant deleting them off the SD card (should have specified). I'd be keeping them on my fileserver to ensure that I can reflash the sdcard to the same version I started with if I need to.
leapinlar said:
Setting up the SD
Begin by downloading the files you need either with stock or your PC. You will need my updated SD image file, attached below, the CM ROM zip you want to install and the gapps zip to match it. Put the last two zips on your internal media sdcard.
Click to expand...
Click to collapse
I'm confused by this, what are you referring to as "internal media sdcard"? I used win32 to burn the .img file, then booted into CWM...I'm clearly doing this wrong, because after that, the sdcard only has 117mb and no room to put ROMs on
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
KamikazeChris said:
I'm confused by this, what are you referring to as "internal media sdcard"? I used win32 to burn the .img file, then booted into CWM...I'm clearly doing this wrong, because after that, the sdcard only has 117mb and no room to put ROMs on
Click to expand...
Click to collapse
You are doing it right. 117MB is what it is supposed to have. You do not put the files on that card. You put them on the HD+ (on the internal sdcard).
If you could see that it only had 117 MB, you were not booted to CWM, you were looking at the SD while it was still inserted in the PC. Booted to CWM means it is in the Nook.
When you insert the burned SD into the powered off HD+, then turn it on, it boots to CWM. That is what I mean by booting to CWM.
The internal sdcard means the storage that is built into the HD+ (that is why I call it internal). Boot to stock and download the files with it. They get put on the internal sdcard or "sdcard" as it is called. After you insert the burned card into the HD+ and boot to it, CWM has the ability to flash the zips by reading them from the internal sdcard built into the HD+.
Edit: I just clarified that in the OP. It is hard to anticipate how users will interpret your words in advance.
Sent from my Nook HD+ running CM10 on Hybrid SD
i dont seem to understand what file is supposed to amount to about 120mb. i extract "cm-10-20121231-UNOFFICIAL-ovation" and amounts to more than 200mb's but it also replaces other files.
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
droidbot1337 said:
i dont seem to understand what file is supposed to amount to about 120mb. i extract "cm-10-20121231-UNOFFICIAL-ovation" and amounts to more than 200mb's but it also replaces other files.
Click to expand...
Click to collapse
You do not extract the cm zip. You extract the image zip which is attached to the post. It is the one that is 120 MB and is the one you burn to the SD with win32diskimager.
Sent from my Nook HD+ running CM10 on Hybrid SD
leapinlar said:
You do not extract the cm zip. You extract the image zip which is attached to the post. It is the one that is 120 MB and is the one you burn to the SD with win32diskimager.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
thank you for the help. i appreciate it! i can now use my new HD+ (bought it last night) to its full potential.
I just wanted to say that I was suffering from the dreaded "Nook refuses to boot from the SD card" syndrome. I tried three different SD cards burned using four different computers, to no avail. Tried this patch? Worked perfectly. Thanks! :laugh:
SDXC cards viable for this use?
Well, that registration video was a real interesting bit compared to most forums I've ever used. Somebody put a lot of work into that.
I'm noticing a lot of emphasis on Class 4 cards. Impetuous sort that I am, I already obtained a Sandisk Ultra 64 GB microSDXC (Class 10/UHS 1) card for this project. Best Buy had a good deal and I was hoping to have a lot of room to work with and it wasn't clear what access to the internal storage would be available or best left alone. Has anyone had success or great problems with this card?
Other than that issue before attempting to execute the install, this is a very helpful thread. Much clearer than verygreen's original. That shouldn't be taken as an insult to verygreen as technical writing for those outside a project is not a skill everyone has or should have. Asking those deep within a project to shift mental gears to operate at the outsider's level can be a waste of resources and is often better delegated to a specialist. And we should be thankful for those specialists when they volunteer like this.
Epobirs said:
I'm noticing a lot of emphasis on Class 4 cards. Impetuous sort that I am, I already obtained a Sandisk Ultra 64 GB microSDXC (Class 10/UHS 1) card for this project. Best Buy had a good deal and I was hoping to have a lot of room to work with and it wasn't clear what access to the internal storage would be available or best left alone. Has anyone had success or great problems with this card?
Click to expand...
Click to collapse
Some have had good success with that card, especially if they use my Hybrid setup which uses less of the SD to operate from.
leapinlar said:
Some have had good success with that card, especially if they use my Hybrid setup which uses less of the SD to operate from.
Click to expand...
Click to collapse
It appears to be working on the first try. I'm currently syncing my app set from the Play store. It looks like this will be a huge value add for the Nook. I wouldn't have bought it if the full Android option weren't there. I just hope enough of us still buy books from B&N to keep them going.
Thanks.