Related
My Kindle Fire is dead, i flashed ICS and everything went ok, after a couple of hours i switched the KF on and nothing happened.
The KF button becomes green for a second, then the light switches off and nothing on the screen appears.
If i connect it to the computer the button light doesn't become orange like when it is recharging, if i try to switch again nothing happens.
Any suggestions?
I cannot give it back as i have bought in the States and now i'm in Europe.
I think you have the same error as I just had. Plug it in and press the power button until something comes up on your computer. (OMAP4430 Device?) If so, try this: http://forum.xda-developers.com/showthread.php?t=1413951
If not you could try shorting the pins... see the thread i link to in that thread.
thank you very much.
I tryed now to press the power button for 30 seconds and now KF is alive again.
Looks like very weird this problem.
I will flash back CM7 and hope to have no problems again
I am stuck at the yellow triangle. It keeps rebooting and it wont let me connect it to the computer. I need help!!!
cashman2419 said:
I am stuck at the yellow triangle. It keeps rebooting and it wont let me connect it to the computer. I need help!!!
Click to expand...
Click to collapse
Boot into TWRP... then follow my other directions.
From the op of KFU thread:
Known Tricks
•If you end up stuck at the yellow triangle, in KF Utility select Boot Normal, wait for it to say <waiting for device> and then press and hold the power button 20 seconds until the fire turns off, then when its off turn it back on. This sometimes happens, I have yet to find a clean solution
•If you end up stuck with a yellow triangle, do not EVER unplug it. Leave it plugged in. Check the windows drivers to make sure it isnt showing as "kindle" again. Fastboot is different and can cause this.
That fixed my issues in fastboot when I was trying to install TWRP the first time. If that doesn't work then [URL="http://forum.xda-developers.com/showpost.php?p=20945694&postcount=506]check out this post[/URL]
I cannot boot into TWRP because the kindle keeps shutting off because it is dead. It isn't read by the computer.
Plug it into electrical outlet and leave it alone for three hours.
While waitin for three hours assess your problem and find the solution. Search.
Then execute solution after fire is charged.
Will it charge even when it keeps turning on and off?
cashman2419 said:
Will it charge even when it keeps turning on and off?
Click to expand...
Click to collapse
Yes it will keep charging.
It did not charge... At least I don't think it did..
When you plug it in do you get a solid color or is the light flashing?
When it's plugged in to the wall and the light is solid you should perform a hard reset by holding power for 20 seconds. This will fully shut down your KF and it will accept the charge
If by flashing you mean turning on and off by itself than yes, it is flashing.
Please help..I'm losing it
Same problem here. It does not seem to charge when plugged into either wall or computer. The green light flashes on and off repeatedly and the recovery screen (yellow triangle) just comes on and off (it eventually just goes black while the green power light continues to turn on and off)
in order to help myself I have done a few things
1: KFU isnt working.
I updated the drivers through KFU
I tried to change bootmode to "normal" and it hung on "waiting for device" I tried hard reset here and nada
2: I tried booting into normal fastboot 4000 through command prompt and hung on "waiting for device" tried reset..nada
So just like the poster above I cannot get into TWRP as the computer never truly recognizes the KF. This all happened when my wife turned on my kf and didnt know what the TWRP was and hit the power button for recovery. It loaded back to the stock kindle set (I had been using CM7) and since then I've been eating FUBAR soup as it doesnt work
Seriously..im pulling my hair out here...any help? I'd try to return the kf to Amazon and save myself the pain but I think we know what would happen when they plug it in and see the flashing triangle...lol
1. Plug your kindle in to the wall for 3 hours like someone mentioned previously (it will charge) The issue with the device being in a boot loop has nothing to do with the kindle fire not charging, this is perfectly normal if you have modified system files and the system can't boot the Android OS. It is also normal to never get past the Yellow Triangle if for some reason that you have changed to FastBoot mode. (Some people may be misinformed thinking that FastBoot does what it sounds like it does (boot fast - not the case), that's how this usually happens)
2. After you know the kindle has been charged for at least 3 hours on a known working power outlet. Press and hold the power button on the kindle for 20 seconds or longer until the device powers down completely.
3. Press the Power button to turn the kindle fire back on, and be ready, as it comes back on press the power button as soon as the Yellow Triangle (firefirefire) logo first appears. Press it up to 5 times rapidly. If you get to TWRP then you can relax. - If you get to the Yellow Triangle and you have pressed the Power button a few times but it is still stuck in a boot loop before giving up try one more time to shut down completely and reboot while pressing Power button rapidly.. You want to be sure to do this before the Yellow Triangle screen goes dim .
4. When you are in TWRP you should be able to use KFU or ADB. You may want to change the boot mode if it is not already to "Normal" if you are having this problem with "Normal" then try to reflash the Kindle with a recovery image or a new ROM.
Hopefully you can at least get to TWRP by following this, so that you can at least flash the kindle with a different update.zip. Good Luck
Charged like you said...still no charge. Flashes on and off and when you pull the power cord goes to black like its dead and will not turn on at all whether you hold it down or just push it...
Never had a problem like this before, could always at least get it to turn on or off not a mix of both lol. Thanks for the help...any more ideas on how to get it where I can at least get it into recovery?
MattFoley said:
Charged like you said...still no charge. Flashes on and off and when you pull the power cord goes to black like its dead and will not turn on at all whether you hold it down or just push it...
Never had a problem like this before, could always at least get it to turn on or off not a mix of both lol. Thanks for the help...any more ideas on how to get it where I can at least get it into recovery?
Click to expand...
Click to collapse
I'm experiencing the same thing.
I'm still confused... are you guys trying to charge it while it is in the boot loop?
Have you tried turning it off (holding down the power button for 20-30 seconds until the screen and the power button go dark and stay dark)? And then plugging it in? I wouldn't expect you to see the firefirefire triangle if the device is off while charging.
The other thing that you might want to look into is the factory cable. Supposedly charges the device and can access it w/o any battery power at all - if I understand that thread correctly.
The point is you can't turn it off, it's dead. If you try to put it on charger either through wall charger or USB, it blinks on and off repeatedly and the power button does nothing at all. The computer won't recognize (tried several diff ports and pcs)
I'm beginning to think the factory cable is my only option to bypass the bootloop and fix it, just hoping I wouldn't have to wait so long for a cable or drop 40 bucks on it. I guess that's what I get for messing something up!
I left it bootlooping for like 6 hours on the charger. Unplug it and you can't turn it on. Plug it in and it bootloops and you can't turn it off. So is this just bricked for good with no possible fix?
MattFoley said:
The point is you can't turn it off, it's dead. If you try to put it on charger either through wall charger or USB, it blinks on and off repeatedly and the power button does nothing at all.
Click to expand...
Click to collapse
Sorry. I was obviously hoping I was misinterpreting.
MattFoley said:
I'm beginning to think the factory cable is my only option to bypass the bootloop and fix it, just hoping I wouldn't have to wait so long for a cable or drop 40 bucks on it. I guess that's what I get for messing something up!
Click to expand...
Click to collapse
You may want to PM SkOrPn, http://forum.xda-developers.com/showpost.php?p=23024666&postcount=108, seems like he has them for $15/$19 depending on length (if your location is accurate.)
Kindle fire turning on and off by itself and won't charge
The only way I know around that problem is unfortunately to remove the back cover and remove the battery with a good adjustable power supply apply 3.7V to the battery for a 30 to 60sec it will draw approx. 3.4A and over the 30 - 60sec the current draw by the battery will drop. Be very careful as you don’t want to blow it up. Put the battery back in and you should find the kindle will charge again. Good luck
Hmmm, I wonder if the factory cable would be an alternative as last I checked an adjustable power supply (if you're without one) can run 70-100 bucks which is half of the kindle itself, I'd almost just take my chances sending it back in to amazon. Thanks for the help though from someone who has had the problem
Today, after I was done using my tablet, I shut it off and noticed it turned off but the green led portion of the power light is still on. Tablet will not respond to power on/off commands, nor can I gain access to it via adb.
I updated to the Energy™ -.¸¸.·´¯ ICS CM9 Kang ROM several days ago, there were no problems there as I have been using the rom for a couple of days now.
All I did was hold the power button down, select "Power down" option came up "this will shut down your tablet" I selected "ok" and that was that.
KFU shows it as offline, as does adb. Windows does not detect the device.
Mine had a similar experience, using AOKP ICS, I powered it off and about 18 hours later I tried to turn it on and got nothing. Turned out the battery was just dead, I think it may have locked up while powering down and killed the battery. I would try a few things:
1. Hold down the power button for 10+ seconds and see if you can get it to do a hard shutdown.
2. Plug it in to the charger and see what happens.
3. Leave it alone for a while and hope the battery dies and it may start up after that when plugged in.
I kind of feel stupid, why is it with technology us geeks start troubleshooting by skipping the simple solutions, like "is it plugged in" well today, holding down the power button for 20 seconds fixed the problem. She booted up and everything is back to normal.
Appreciate the fast reply!
Today I picked up may Nexus 7 and noticed it will not turn on. I let it charge for an hour or so, but then when I tried to start it up, I saw just a black screen. The screen turns on (backlight turns on), but still just a black screen. I read something on the internet about pressing the power button for a full 30 seconds, so I tried that. This time, I got it to flash (for a fraction of a second) the word "Google", and then it was back to the black screen of nothing.
I've never rooted, never tried to do anything fancy with it. I've factory resetted it once after an update to the OS happened.
Is there anything I can do?
You sure it gets juice? Does your charger feel hot after charging some time?
I had this to once, but got it fixed by holding the power button...
Sent from my Nexus 7 using xda premium
Sounds like a charging /battery issue if the 30 sec power didnt work.Did you try a different charger?
Some people have reported weird issues like this that have been rectified by a prolonged charging.
Thanks
It acted strange, but it came back from the dead:
It said "google" for 10 seconds, then a few seconds of black screen, then another 10 seconds of "google", then it booted just enough to tell me that it was going to shut down because of low battery. I let it charge another hour and then it was fine!
eddified said:
It acted strange, but it came back from the dead:
It said "google" for 10 seconds, then a few seconds of black screen, then another 10 seconds of "google", then it booted just enough to tell me that it was going to shut down because of low battery. I let it charge another hour and then it was fine!
Click to expand...
Click to collapse
Quirky little buggers aren't they? Mine did it once and not since.
I just goy my N7 today, plugged in the wall charger, and I'm stuck at black screen, I did the 30 secs hold power button but it's still and black screen. Also I tried this:
1. Plug-in your dead N7 to a wall charger. (Jump immediately to step 2.)
2. Immediately after plugging it in, press Volume Down and Power at the same time.
3. Once in the bootloader menu, use Volume Down until you see “Power Off Device.”
4. Choose that option with the Power button.
5. Once your device is off, unplug the charger and then plug it back into the device.
Still at black screen, any advice???
I'm sorry for posting in this old thread.
Jamiehefe said:
I just goy my N7 today, plugged in the wall charger, and I'm stuck at black screen, I did the 30 secs hold power button but it's still and black screen. Also I tried this:
1. Plug-in your dead N7 to a wall charger. (Jump immediately to step 2.)
2. Immediately after plugging it in, press Volume Down and Power at the same time.
3. Once in the bootloader menu, use Volume Down until you see “Power Off Device.”
4. Choose that option with the Power button.
5. Once your device is off, unplug the charger and then plug it back into the device.
Still at black screen, any advice???
I'm sorry for posting in this old thread.
Click to expand...
Click to collapse
I just solved this, I opened my N7 to check the battery and it turns out it wasn't correctly connected... Just unplugged it and plug in again correctly to make it work!
Jamiehefe said:
I just solved this, I opened my N7 to check the battery and it turns out it wasn't correctly connected... Just unplugged it and plug in again correctly to make it work!
Click to expand...
Click to collapse
Boom!
I was having the same problem. Plugged it into a power source, backlight would come on with a black screen. Got it to show the Google splash screen a few times, but it just wouldn't boot. Tried ADB, but it wouldn't even acknowledge the thing was connected to the PC. I tried a pile of stuffs. Then I read this post. I never thought to check if the thing was actually connected, it wasn't!
Fully functional device now. Thanks for the idea! :good:
Few weeks ago I found wife's old NST (non-glowlight model) in working order and decided to root it. Rooted it, played around with it. Wasnt too impressed, so just threw some ebooks for my kid to read while on vacation. Left it on my desk for a few weeks as I got busy with work. Today I picked it up as my son's vacation is next week and it's frozen on the "Installing... A new software update is being installed This will take a few minutes" screen.
I mean I googled for several hours, the hold the power button for 20 sec method....the hold the power and the "n" button method, I charged it, indicator light is green. I even opened it up and pulled the battery cable..... NOTHING WORKS...]
Please help. So weird...it was working fine and now frozen.
KEVIN88GT said:
Few weeks ago I found wife's old NST (non-glowlight model) in working order and decided to root it. Rooted it, played around with it. Wasnt too impressed, so just threw some ebooks for my kid to read while on vacation. Left it on my desk for a few weeks as I got busy with work. Today I picked it up as my son's vacation is next week and it's frozen on the "Installing... A new software update is being installed This will take a few minutes" screen.
I mean I googled for several hours, the hold the power button for 20 sec method....the hold the power and the "n" button method, I charged it, indicator light is green. I even opened it up and pulled the battery cable..... NOTHING WORKS...]
Please help. So weird...it was working fine and now frozen.
Click to expand...
Click to collapse
The real question is whether it is actually still on or off. What happens when you connect it to a PC via USB?
nmyshkin said:
The real question is whether it is actually still on or off. What happens when you connect it to a PC via USB?
Click to expand...
Click to collapse
Only the green charging light goes on. I do not hear the little sound it should make when making a successful USB connection.
KEVIN88GT said:
Only the green charging light goes on. I do not hear the little sound it should make when making a successful USB connection.
Click to expand...
Click to collapse
And I guess the drives don't mount successfully. Well, disconnecting the battery should certainly turn it off. If reconnecting makes it start spontaneously (should not), you could prepare a Nook Manager sdcard and insert it before reconnecting the battery. But this sort of sounds like the ability to boot is lost. Hmmm. I'll have to think about it.
unfortunately disconnecting the battery does not appear to do anything... screen continues to show that 'Installing... " screen. Hoping to get this thing figured out with someone's help
KEVIN88GT said:
unfortunately disconnecting the battery does not appear to do anything... screen continues to show that 'Installing... " screen. Hoping to get this thing figured out with someone's help
Click to expand...
Click to collapse
E-ink screens stay the same unless there is a new powered input so it could simply be off, having run the battery down completely during an update (maybe Wi-Fi was left on? That would run down the battery for sure). So if all of this happened during an OTA update, it could be really messed up
When my NST is off, plugging in the power pack turns it on. Initially the LED is green and then changes to orange as charging begins. I'm assuming nothing happens when you do the same. If the OS is scrambled from losing power during an update it may not be able to boot. You didn't say how you rooted. If you used Nook Manager you could try putting in that card and then connecting to the power pack, hoping for a boot from the SD card. If you got that far you could try a factory reset.
My power button is sometimes really cranky and a few times I've run through my entire stock of words that do not come from children's books trying to get the device to turn on. So you might try, but if it's really off the power pack should turn it on.
Edit: Take a look at this: https://forum.xda-developers.com/showthread.php?t=1813384
nmyshkin said:
E-ink screens stay the same unless there is a new powered input so it could simply be off, having run the battery down completely during an update (maybe Wi-Fi was left on? That would run down the battery for sure). So if all of this happened during an OTA update, it could be really messed up
When my NST is off, plugging in the power pack turns it on. Initially the LED is green and then changes to orange as charging begins. I'm assuming nothing happens when you do the same. If the OS is scrambled from losing power during an update it may not be able to boot. You didn't say how you rooted. If you used Nook Manager you could try putting in that card and then connecting to the power pack, hoping for a boot from the SD card. If you got that far you could try a factory reset.
My power button is sometimes really cranky and a few times I've run through my entire stock of words that do not come from children's books trying to get the device to turn on. So you might try, but if it's really off the power pack should turn it on.
Edit: Take a look at this: https://forum.xda-developers.com/showthread.php?t=1813384
Click to expand...
Click to collapse
When I plug in the power cable the light just becomes green it never (not even for a split second) turns orange. Yes, I'm rooted using nook manager. I just suck my Nook Manager SD card in the nook but nothing happens. I'm not sure what you mean by using the power button, in my original post I mentioned I tried the power button with no luck. What do you mean by power pack?
KEVIN88GT said:
When I plug in the power cable the light just becomes green it never (not even for a split second) turns orange. Yes, I'm rooted using nook manager. I just suck my Nook Manager SD card in the nook but nothing happens. I'm not sure what you mean by using the power button, in my original post I mentioned I tried the power button with no luck. What do you mean by power pack?
Click to expand...
Click to collapse
Power pack = charger.
So if the Nook is actually off, attaching the charger with the NM card inserted should make it boot. Did you try the procedure in the link above?
Just tried the procedure of unplugging the battery, holding the white power button for 30 secs, then connecting battery and connecting to charger. There is a split second orange light and then green the first time i plug it in....subsequent plugging results in always green....the issue with the frozen screen on "Installing" remains. Tried the holding x 20 secs method to promt a restart....nothing.... what else can I do?
KEVIN88GT said:
Just tried the procedure of unplugging the battery, holding the white power button for 30 secs, then connecting battery and connecting to charger. There is a split second orange light and then green the first time i plug it in....subsequent plugging results in always green....the issue with the frozen screen on "Installing" remains. Tried the holding x 20 secs method to promt a restart....nothing.... what else can I do?
Click to expand...
Click to collapse
If the battery is actually "dead" (not impossible on these old devices), the NST will not start, even if plugged in. Do you have a voltmeter of some sort to check the battery? If it's actually charged, it should show a solid voltage. If not, that may be the issue. If the battery is actually charged then there's a pretty serious issue that can't be fixed without access to the OS by ADB, or the ability to boot from the SD card. Beyond my "pay grade", at any rate, I'm sorry to say. There are batteries available online but the price may not make sense.
I don't think it's a battery issue. I had another NST with a good battery but a bad screen (lines all across screen) . I fully charged it using the bad screen reader and used the battery from it for the frozen nook... no luck.. oh well... I guess this is a paperweight now... thanks for your help everyone.