Hello everyone. My question is: is there any help?
My gt540 is just bricked. I turn mobile on, i only see black screen, no lg, no anything. Computer is not recognizing it, before kdz was throw out an error.
I tried everything from download mode, emergency mode, diag, emergency, emergency_cs and everytime kdz would stop before end. Tried with different kdz files, different drivers, don't know what I can do else.
Is there any help?
Can you write all recovery/download/fastboot modes and how to get to them? And anything else to try? Cable is working fine test on other cellphone, my computer is windows 7 x64. Please help thank you
Re
Go to someone who has WIN XP 32 Bit istall drivers and try it all again...
djfoxserbia said:
Go to someone who has WIN XP 32 Bit istall drivers and try it all again...
Click to expand...
Click to collapse
Pozdrav kolega problem je što ga jednostavno pc ne prepoznaje da je ikakav uređaj spojen sa ili bez drivera.
English translation
The problem is that pc (windows and xp) does not recognized that phone is even connected, with or without drivers.
you got a recovery program flashed to it?
aaa801 said:
you got a recovery program flashed to it?
Click to expand...
Click to collapse
Well I think not, because computer is just not recognized it, and I can not enter any mode (volume down, power + camera) Is there any help?
sipe1 said:
Well I think not, because computer is just not recognized it, and I can not enter any mode (volume down, power + camera) Is there any help?
Click to expand...
Click to collapse
Probably not if you can't access fastboot or recovery. Sorry.
Sent from my GT540 using Tapatalk
si probo skinuti drivere za win 7 da ne zezaju oni? i jesi iskljucio virtual modem u device manageru?
brzijazo said:
si probo skinuti drivere za win 7 da ne zezaju oni? i jesi iskljucio virtual modem u device manageru?
Click to expand...
Click to collapse
Jesam, i druge kompove sam probao ništa :/
Try to use the drivers in this post: http://forum.xda-developers.com/showpost.php?p=12898827&postcount=3
Try to use kdz like in here: http://forum.xda-developers.com/showpost.php?p=10238074&postcount=41
Try a hard reset:
1) Start your phone [phone must be started with or without sim]
2) Press volume up button + home button + search button
[Location of volume up button is on right side, location for home button is on bottom middle button of home screen and search button is right side of phone above camera button]
3) Keep all those button pressed at the same time for 5 second
4) Phone will ask you for " Are you sure you want to factory reset?"
5) Press yes and wait for 1 minute, Phone will hang first and than restart after sometime.
6) You've done resetting your GT540 successfully
Hope it can help.
Rne800 said:
Try to use the drivers in this post: http://forum.xda-developers.com/showpost.php?p=12898827&postcount=3
Try to use kdz like in here: http://forum.xda-developers.com/showpost.php?p=10238074&postcount=41
Try a hard reset:
1) Start your phone [phone must be started with or without sim]
2) Press volume up button + home button + search button
[Location of volume up button is on right side, location for home button is on bottom middle button of home screen and search button is right side of phone above camera button]
3) Keep all those button pressed at the same time for 5 second
4) Phone will ask you for " Are you sure you want to factory reset?"
5) Press yes and wait for 1 minute, Phone will hang first and than restart after sometime.
6) You've done resetting your GT540 successfully
Hope it can help.
Click to expand...
Click to collapse
Hi. It seem`s i have the same problem as the guy who made this topic had. But i just cant seem to get it into the download mode. http://forum.xda-developers.com/showpost.php?p=10238074&postcount=41 when i plug in the usb i too the pc and take out everything in my phone like sd card sim card and the battery when i pres vol - and plug it in nothing happens.
Rne800 said:
Try to use the drivers in this post: http://forum.xda-developers.com/showpost.php?p=12898827&postcount=3
Try to use kdz like in here: http://forum.xda-developers.com/showpost.php?p=10238074&postcount=41
Try a hard reset:
1) Start your phone [phone must be started with or without sim]
2) Press volume up button + home button + search button
[Location of volume up button is on right side, location for home button is on bottom middle button of home screen and search button is right side of phone above camera button]
3) Keep all those button pressed at the same time for 5 second
4) Phone will ask you for " Are you sure you want to factory reset?"
5) Press yes and wait for 1 minute, Phone will hang first and than restart after sometime.
6) You've done resetting your GT540 successfully
Hope it can help.
Click to expand...
Click to collapse
Hi friend, I have the same problem with the other guys. I was trying to install fastboot when it showed an error on kdz.
After that my phone was stuck at the LG logo. I can run kdz in emergency mode but the install of the fastboot rom never finishes, it also does not show any errors. It seems to be installing for ever.
What can I do?
Thanks.
if your phone has fastboot or recovery you can fix it very fast
no s**t
Sent using Lewa
sry for my bad english
try to hold only volume down
reinstall drivers
put kdz in emergency mode and install euro 2.1 + fastboot
Sent using Lewa
sry for my bad english
I've the same problem too my LG GT540 is bricked. It only vibrates when i turn it on! I need help someone
I have the same problem, my cell phone onlt vibrates when i try do torn on
Related
Hi,
one day, I changed the permission of /system/font by accident:
e.g. I changed:
.............read....write.....execute
user.........V........V...........V
group.......V.....................V
others......V.....................V
to
............read.......write......execute
user........V..........V..............
group.......V.........................
others......V.........................
After that, I can't turn on my phone anymore T.T
When I press the power button, the LG logo appears, and then vibrate, logo disappear, after a few seconds the logo comes back and that's it!
It just stays there (I waited for 2 hours and it didn't change,so I turned it off)
Please help~
How can i fix it...
leelulu4fb said:
Hi,
one day, I changed the permission of /system/font by accident:
e.g. I changed:
.............read....write.....execute
user.........V........V...........V
group.......V.....................V
others......V.....................V
to
............read.......write......execute
user........V..........V..............
group.......V.........................
others......V.........................
After that, I can't turn on my phone anymore T.T
When I press the power button, the LG logo appears, and then vibrate, logo disappear, after a few seconds the logo comes back and that's it!
It just stays there (I waited for 2 hours and it didn't change,so I turned it off)
Please help~
How can i fix it...
Click to expand...
Click to collapse
Enter download mode, and flash your firmware like this: http://forum.xda-developers.com/showthread.php?t=2409308 or just open LG Mobile Support Tool and select "Recover Phone". It does the same thing but it's easier.
Nothing's lost, you'll get it fixed.
mircea89fzr said:
Enter download mode, and flash your firmware like this: http://forum.xda-developers.com/showthread.php?t=2409308 or just open LG Mobile Support Tool and select "Recover Phone". It does the same thing but it's easier.
Nothing's lost, you'll get it fixed.
Click to expand...
Click to collapse
hi, thanks a lot.
but what is "version"? There are version 10C/10E/20A in http://lg-phone-firmware.com/index.php?mod=Lg+Optimus+L7&paese=RGS/ROGERS&id_mod=13 ...
How can I know which one is the right one?
leelulu4fb said:
hi, thanks a lot.
but what is "version"? There are version 10C/10E/20A in http://lg-phone-firmware.com/index.php?mod=Lg+Optimus+L7&paese=RGS/ROGERS&id_mod=13 ...
How can I know which one is the right one?
Click to expand...
Click to collapse
My guess is 20A is ICS, 10C is the first release of Gingerbread, and 10E whatever update they did to it. If you're not sure, go with the LG Mob Supp Tool, it's safer and easier.
mircea89fzr said:
Enter download mode, and flash your firmware like this: http://forum.xda-developers.com/showthread.php?t=2409308 or just open LG Mobile Support Tool and select "Recover Phone". It does the same thing but it's easier.
Nothing's lost, you'll get it fixed.
Click to expand...
Click to collapse
one more problem, I can't access to download mode, I press vol+ & power, but nothing happen
leelulu4fb said:
one more problem, I can't access to download mode, I press vol+ & power, but nothing happen
Click to expand...
Click to collapse
Did it work before with the exact firmware update you had? Remove the battery of your phone and re-insert it (don’t turn it on). Press and hold Volume Up button and Volume Down button. While you are pressing the two buttons, press the Power button or insert USB cable (try both if it doesn't work). Or try with: phone off, volume down + insert cable. I don't know the exact combination for your phone.
leelulu4fb said:
one more problem, I can't access to download mode, I press vol+ & power, but nothing happen
Click to expand...
Click to collapse
try vol down+power
when keys light up, touch menu key (vibrates)
Even if you can't go to download mode you'll still be able to use kdz on it. just plug it in and start it. And btw, be careful next time. My Optimus L7 got hard bricked and I needed to go to LG for them to fix it.
Hi guys.
My phone after installing a rom, maybe corrupted, does not enter into emergency mode or recovery mode or PC Suite USB mode.
There is some more method install another rom?
(my phone is a LG optimus L7)
continuation of a good job guys
Can the pone enter CWM? Try change vol button (if earlier entered by pressing vol+ now try vol- and home and power button until vibrate)
raul338 said:
Can the pone enter CWM? Try change vol button (if earlier entered by pressing vol+ now try vol- and home and power button until vibrate)
Click to expand...
Click to collapse
Yes, already tried with phone but the phone restarts and appears black screen and back to normal start. I've tried all the buttons and sequences but does not work any.
kadekz said:
Yes, already tried with phone but the phone restarts and appears black screen and back to normal start. I've tried all the buttons and sequences but does not work any.
Click to expand...
Click to collapse
Then search for a downgrade kdz here in the forums
raul338 said:
Then search for a downgrade kdz here in the forums
Click to expand...
Click to collapse
Already tried that but I get to the step "USB Connection Type" and I can not abide the "Software for LG usb" :s
kadekz said:
Already tried that but I get to the step "USB Connection Type" and I can not abide the "Software for LG usb" :s
Click to expand...
Click to collapse
You don't need that for a kdz with reset all data... Whats the link for the tutorial that you are following?
raul338 said:
You don't need that for a kdz with reset all data... Whats the link for the tutorial that you are following?
Click to expand...
Click to collapse
I do not follow any tutorial, i'm already used to change the rom through cwm, wipes, install zip from SD through and wipes again.
But now not open the cwm, is black screen and reboots to normal mode. I do not understand what is happening. :x
kadekz said:
I do not follow any tutorial, i'm already used to change the rom through cwm, wipes, install zip from SD through and wipes again.
But now not open the cwm, is black screen and reboots to normal mode. I do not understand what is happening. :x
Click to expand...
Click to collapse
I dont now if this help, but only way that works for me to get into recovery, is holding both, vol+ and vol- keys, while presing home, and power button, when the phone vibrates, release power button, but keep holding vol+, vol- and home button for about 2 seconds, then release everything....
phone should boot into recovery now...
here's a guide for flashing original firmware. http://forum.xda-developers.com/showpost.php?p=31828740&postcount=1191
lots, and i mean, lots of information is on this post http://forum.xda-developers.com/showthread.php?t=1664322.
good luck
vashminted said:
I dont now if this help, but only way that works for me to get into recovery, is holding both, vol+ and vol- keys, while presing home, and power button, when the phone vibrates, release power button, but keep holding vol+, vol- and home button for about 2 seconds, then release everything....
phone should boot into recovery now...
here's a guide for flashing original firmware. http://forum.xda-developers.com/showpost.php?p=31828740&postcount=1191
lots, and i mean, lots of information is on this post http://forum.xda-developers.com/showthread.php?t=1664322.
good luck
Click to expand...
Click to collapse
yes, I also used this combination of keys to enter the recovery once but now does not work, call a black screen and does not vibrate.
By KDZ also can not do anything because they also do not enter the emergency mode or in "pc suite".
Not even know how to solve this problem: x
And the worst is that I need the smartphone
kadekz said:
yes, I also used this combination of keys to enter the recovery once but now does not work, call a black screen and does not vibrate.
By KDZ also can not do anything because they also do not enter the emergency mode or in "pc suite".
Not even know how to solve this problem: x
And the worst is that I need the smartphone
Click to expand...
Click to collapse
How do you enter in emergency mode?
I do it by taking the battery off, then conect the cable to phone, hold vol+ (or vol-, i dont remember) and then conect the cable to the pc
vashminted said:
How do you enter in emergency mode?
I do it by taking the battery off, then conect the cable to phone, hold vol+ (or vol-, i dont remember) and then conect the cable to the pc
Click to expand...
Click to collapse
That is the problem, not enter the emergency mode. : s
Already tried it, until with two combinations of keys but does not work, do not understand: (
I'm having the same exact problem. Early in mornign I flashed a rom with cwm and didnt like it at all. Then I flash the homer v20 with KDZ and now it does not boot, neither the emergency mode works as I install it with that mode.
dude ..remove the battery then press vol down with home and power ..all together until emergency or download mode comes ..if doesnt tri volume up ..if it doesnt then try this ...press volume down with home and power ..the front lights will light for 2 seconds ..just remove finger from home button and still on powe with vol down ..i wish i help you i faced this in my l5 and i think they are the same
hassan216 said:
dude ..remove the battery then press vol down with home and power ..all together until emergency or download mode comes ..if doesnt tri volume up ..if it doesnt then try this ...press volume down with home and power ..the front lights will light for 2 seconds ..just remove finger from home button and still on powe with vol down ..i wish i help you i faced this in my l5 and i think they are the same
Click to expand...
Click to collapse
I already tried all the possible combinations of keys to wake up the smartphone but it does not work neither. That's the bigger problem: (
But thanks anyway for the tip.
there is no solution exists?
Final solution is emergency or download mode. if u can not enter it, u shoud take it to service center as soon as possible
Hello,
I am very new to rooting etc. I rooted my phone a few days ago, unlocked bootloader and tried to flash cm11.0 with rom manager (cwmg) following this link:
http://forum.xda-developers.com/showthread.php?t=2521239
Unfortunately I didn´t understand the instructions well, so after wiping caches, instead of doing a full format I did a user data etc format (which i now think was a factory reset). Tried flashing, didn´t succeed.
Anyway, when I try to switch it on I only get the lg logo and then the batery charging thingy When I try to go to recovery mode with volume up power and menu button, my phone goes on a loop of lg and cyanomod logos untill infinity ( Have to take off the battery). Tried to use heimdall (as i have a mac) to flash kdz back to it, but phone was not recognized. On my pc tried the same, but again phone not seen. I can see it on my computer as an unrecognized external usb but cannot explore. Any ideas on what to do??
thanks in advance
franky.frangi said:
Hello,
I am very new to rooting etc. I rooted my phone a few days ago, unlocked bootloader and tried to flash cm11.0 with rom manager (cwmg) following this link:
http://forum.xda-developers.com/showthread.php?t=2521239
Unfortunately I didn´t understand the instructions well, so after wiping caches, instead of doing a full format I did a user data etc format (which i now think was a factory reset). Tried flashing, didn´t succeed.
Anyway, when I try to switch it on I only get the lg logo and then the batery charging thingy When I try to go to recovery mode with volume up power and menu button, my phone goes on a loop of lg and cyanomod logos untill infinity ( Have to take off the battery). Tried to use heimdall (as i have a mac) to flash kdz back to it, but phone was not recognized. On my pc tried the same, but again phone not seen. I can see it on my computer as an unrecognized external usb but cannot explore. Any ideas on what to do??
thanks in advance
Click to expand...
Click to collapse
power off your device.
long press
1) "vol -"
2) home button
3) power button
for some second
are you able to enter in recovery?
lferlito said:
power off your device.
long press
1) "vol -"
2) home button
3) power button
for some second
are you able to enter in recovery?
Click to expand...
Click to collapse
No, it goes into logos loop.
franky.frangi said:
No, it goes into logos loop.
Click to expand...
Click to collapse
i don't know, man
but for the future, before installing a custom rom
remember to install a recovery
it's very important
hope someone better than me will help you
:fingers-crossed:
lferlito said:
i don't know, man
but for the future, before installing a custom rom
remember to install a recovery
it's very important
hope someone better than me will help you
:fingers-crossed:
Click to expand...
Click to collapse
But I did, throught clockworkmod (first thing I did) ....and also did a nandroid backup...just don´t know how to access them...
franky.frangi said:
But I did, throught clockworkmod (first thing I did) ....and also did a nandroid backup...just don´t know how to access them...
Click to expand...
Click to collapse
on my L5, i long press those 3 buttons until LG logo boot appears..
i wait some second and it appears the CWM reco
i don't know if there are other ways to enter in recovery mode..
yeah me neither.mine used to do the same before the flashing.thanks thought.lets see if someone has another idea...
franky.frangi said:
yeah me neither.mine used to do the same before the flashing.thanks thought.lets see if someone has another idea...
Click to expand...
Click to collapse
As soon as you plug your USB into your phone, hold down the volume up (+) button and the power button and release them after holding them down for about 2 to 3 seconds. Then, install the USB driver for your phone with the LG Mobile Support Tool. Secondly, download and install the LG PC Suite program and last but not least, download the KDZ program. Install the correct firmware for your phone and make sure you select 'EMERGENCY' from the list on the top right of the KDZ program. Select your downloaded firmware file and start the program. If everything worked out, the program should crash after it's done and your phone should reboot. Disconnect your phone from the computer if it doesn't reboot and try to boot it up again.
You can find all of these programs along with tutorials on how they work by searching on either XDA or Google.
did forcing recovery/download work ?
TahaX said:
As soon as you plug your USB into your phone, hold down the volume up (+) button and the power button and release them after holding them down for about 2 to 3 seconds. Then, install the USB driver for your phone with the LG Mobile Support Tool. Secondly, download and install the LG PC Suite program and last but not least, download the KDZ program. Install the correct firmware for your phone and make sure you select 'EMERGENCY' from the list on the top right of the KDZ program. Select your downloaded firmware file and start the program. If everything worked out, the program should crash after it's done and your phone should reboot. Disconnect your phone from the computer if it doesn't reboot and try to boot it up again.
You can find all of these programs along with tutorials on how they work by searching on either XDA or Google.
Click to expand...
Click to collapse
the phone off usb in and buttons did it work ?
Actually didn´t work,I have drivers already, LG PC Suite program , and KDZ. Problem is my phone is not detected by pc, so kdz unzips and then says : phone not detected, with or without battery...doesn´t go into recovery mode with buttons, just lg and cyanomod logos...
I don`t know if this can b fixed.....How can you flash anything if it´s not detected....
I´ll give it a try again tomorrow, without trying to enter recovery mode....but tried lots of buttons combinations and wasn´t working
Press these buttons
volume +
,volume -
home button
together with the power button
release all buttons except power button when you get a vibration
release the power button immediately after the lg logo has appered
this should let you get in the recovery menu
FULL STEP BY STEP GUIDE
found http://forum.xda-developers.com/showthread.php?t=2486512
IGGYVIP said:
Press these buttons
volume +
,volume -
home button
together with the power button
release all buttons except power button when you get a vibration
release the power button immediately after the lg logo has appered
this should let you get in the recovery menu
FULL STEP BY STEP GUIDE
found http://forum.xda-developers.com/showthread.php?t=2486512
Click to expand...
Click to collapse
Finally!! This worked....I can get in the recovery menu!!!
Before I do anything I´ll really think about what rom I want to use )
Thanks lot everyone...hope it gives me no more issues.
franky.frangi said:
Finally!! This worked....I can get in the recovery menu!!!
Before I do anything I´ll really think about what rom I want to use )
Thanks lot everyone...hope it gives me no more issues.
Click to expand...
Click to collapse
happy flashing
Hello to all here at xda im a new member and im hoping someone can help me,
I recently bought a yotaphone 2 from tinydeals in china and its model
P05-Yota which I think is china model YD-205 or 206
I wanted to upgrade the firmware to the latest firmware and I think I made two big mistakes.
First when I downloaded the yotaflasher software for windows I chose the eu firmware on option 2 and clicked to download it.also I dont think I put usb debugging on my phone.i put my phone into diwnloading mode and connected the phone to my pc.my pc recognised the phone and I clicked on option 1 in yotaflasher to flash mobile.
The flash process started but failed on most of the things it was supposes to get access to, my phone reatarted and now its on constant boot loop which shows the android logo.i can boot phone back into downloading mode but nothink else
I have read that as my phone is in boot loop and can still boot into downloading mode its soft bricked and not hard bricked so im guessing thats good news.
This is my own fault and im not very experienced in all this flashing and I fing yotaflasher hard to understand compared to odin ive used on samsung phones before
Please can anyone help a complete novice to revive his mobile
I would be greatful for any help and instructions and dont know if im allowed to do this on this site so I appologise to moderators if im not, but anyone that can help me get my phone working again I will transfer £20 to their paypal account as I would appreciate this help alot
Im sorry for being a noob and hope to hear from someone soon
Thx
Simon h
Sorry for my very, very bad english.
Try to reboot your phone in recovery mode.
Press power button for a long time (20 - 30 seconds or more) and, as soon as the screen turn off, press and hold the Volume Up + Power button simultaneously for about 10 seconds. Then, choose wipe data and factory reset.
Try several times if that does not work at once.
I made a big mistaske too and I solved the problem but with several attemps.
Good luck !
I appreciate your help
cheynei said:
Sorry for my very, very bad english.
Try to reboot your phone in recovery mode.
Press power button for a long time (20 - 30 seconds or more) and, as soon as the screen turn off, press and hold the Volume Up + Power button simultaneously for about 10 seconds. Then, choose wipe data and factory reset.
Try several times if that does not work at once.
I made a big mistaske too and I solved the problem but with several attemps.
y
Good luck !
Click to expand...
Click to collapse
Just wanted to saythanykyou and appreciate your reply and as soon as I get home I will try and boot into recovery and see how that goes.will update on progress
Again thankyou
simon121simon said:
Just wanted to saythanykyou and appreciate your reply and as soon as I get home I will try and boot into recovery and see how that goes.will update on progress
Again thankyou
Click to expand...
Click to collapse
No problem, I think it's the only solution... but you will loose all your data (I bought my yotaphone from tinydeals too and I killed it too)...
:fingers-crossed:
queation about yotaflasher
cheynei said:
No problem, I think it's the only solution... but you will loose all your data (I aboutbought my yotaphone from tinydeals too and I killed it too)...
:fingers-crossed:
Click to expand...
Click to collapse
Just a quick question, yotaflasher is a software im not familiar with and im not sure if im using it right.
Do I start yotaflasher and then type 2 and enter tochoose region.then type the number for the firmware I want and press enter.then when its finished downloading it seems ro freeze and I cant type any key to start flash so I have to exit software then restart it.
Do I then just type 1 and enter to start flashing phone then thats it or do you have to type proper commands into this software ro get it to work as im not sure if im using it right
I will be home in couple of hrs to test out what you told me
Thx
simon121simon said:
Just a quick question, yotaflasher is a software im not familiar with and im not sure if im using it right.
Do I start yotaflasher and then type 2 and enter tochoose region.then type the number for the firmware I want and press enter.then when its finished downloading it seems ro freeze and I cant type any key to start flash so I have to exit software then restart it.
Do I then just type 1 and enter to start flashing phone then thats it or do you have to type proper commands into this software ro get it to work as im not sure if im using it right
I will be home in couple of hrs to test out what you told me
Thx
Click to expand...
Click to collapse
Sorry again for my english...
1. without any software, reset your phone : turn off your phone (or, if it's not possible, press power button for a long time :20 - 30 seconds or more - and, as soon as the screen turn off) --> press and hold the Volume Up + Power button simultaneously for about 10 seconds. Then, choose "wipe data and factory reset" and wait...
2. After the reboot, put usb debugging on your phone
3 . install yotaflasher (so you also have the drivers on your computer).
4. put your phone on download mode : turn off your phone - then, press and hold the Volume down + Power button simultaneously for about 10 seconds
5. open yotaflasher on your computer and connect your phone (wich is on download mode)
6. chose the last EU firmware (option 2) and download it - after, click on option 1 and flash your mobile. Wait the necessary time without touch anything and, after maybe 10 ou 15 minutes, your phone will reboot.
We have the same phone from Tinydeals and I'm now on lolipop (after the flash).
Good luck !
usb debugging is the problem
cheynei said:
Sorry again for my english...
1. without any software, reset your phone : turn off your phone (or, if it's not possible, press power button for a long time :20 - 30 seconds or more - and, as soon as the screen turn off) --> press and hold the Volume Up + Power button simultaneously for about 10 seconds. Then, choose "wipe data and factory reset" and wait...
2. After the reboot, put usb debugging on your phone
3 . install yotaflasher (so you also have the drivers on your computer).
4. put your phone on download mode : turn off your phone - then, press and hold the Volume down + Power button simultaneously for about 10 seconds
5. open yotaflasher on your computer and connect your phone (wich is on download mode)
6. chose the last EU firmware (option 2) and download it - after, click on option 1 and flash your mobile. Wait the necessary time without touch anything and, after maybe 10 ou 15 minutes, your phone will reboot.
We have the same phone from Tinydeals and I'm now on lolipop (after the flash).
Good luck !
Click to expand...
Click to collapse
Hi there mate thx for the step by step guide but I think I know what the problem is.i originally didnt put it into usb debugging mode when I originally tried to flash the firmware.now as the mobile is stuck in boot loop and cant load up as normal I cant switch on usb debugging.is there a way through fastboot or that adb program.im just learning about these programs to flash mobiles with but if there is no way to enable usb debugging through any software I fear im screwed
simon121simon said:
Hi there mate thx for the step by step guide but I think I know what the problem is.i originally didnt put it into usb debugging mode when I originally tried to flash the firmware.now as the mobile is stuck in boot loop and cant load up as normal I cant switch on usb debugging.is there a way through fastboot or that adb program.im just learning about these programs to flash mobiles with but if there is no way to enable usb debugging through any software I fear im screwed
Click to expand...
Click to collapse
Yes, I know, don't worry, I bug my phone too - it's why you have, first, to reset your phone... try to put it on recovery mode, it's the only solution (I think).
--> Press the power button for a long time (20 - 30 seconds or more) and, as soon as the screen turn off, press and hold the Volume Up + Power button simultaneously for about 10 seconds. Then, you will see a menu : choose "wipe data and factory reset".
Try several times if that does not work at once.
i have a lg spirit H440F
I might have delete some files in the root folder , result is a blank screen
I cannot enter the phone
It s possible to see the download mode when i push volume
factory reset doesnt work
What can i do ? or is the phone dead?
thanks a lot
papilonaa said:
i have a lg spirit H440F
I might have delete some files in the root folder , result is a blank screen
I cannot enter the phone
It s possible to see the download mode when i push volume
factory reset doesnt work
What can i do ? or is the phone dead?
thanks a lot
Click to expand...
Click to collapse
Turn off the phone. Plug the PC end of the USB cable in the PC. Press and hold volume up and plug in the USB cable in the phone. Hold it like that. After a couple of seconds, you should be in download mode. Then use LG Flashtool/LGUP to flash Lolipop/Marshmallow.
now stuck on logo
Fobos531 said:
Turn off the phone. Plug the PC end of the USB cable in the PC. Press and hold volume up and plug in the USB cable in the phone. Hold it like that. After a couple of seconds, you should be in download mode. Then use LG Flashtool/LGUP to flash Lolipop/Marshmallow.
Click to expand...
Click to collapse
Helo thanks a lot to you for helping me
since that day i could le't the LG recognize on the xp and flash it with the usual tool.
Now after the process finished, i reboot and it stay stuck on the logo, some time come for a second the green android who say erasing process, then again the logo
That s it
please what next can i try?
thanks
papilonaa said:
Helo thanks a lot to you for helping me
since that day i could le't the LG recognize on the xp and flash it with the usual tool.
Now after the process finished, i reboot and it stay stuck on the logo, some time come for a second the green android who say erasing process, then again the logo
That s it
please what next can i try?
thanks
Click to expand...
Click to collapse
what frimware did you flash? can you try performing a factory reset? to do so:
1) turn off the phone
2) press and hold volume down + power keys until the lg logo appears
3) let go of the both keys for 1 second
4) immediately press and hold them again (both keys) until you get to a factory reset screen. Follow the onscreen instrucitons.
Fobos531 said:
what frimware did you flash? can you try performing a factory reset? to do so:
1) turn off the phone
2) press and hold volume down + power keys until the lg logo appears
3) let go of the both keys for 1 second
4) immediately press and hold them again (both keys) until you get to a factory reset screen. Follow the onscreen instrucitons.
Click to expand...
Click to collapse
Thanks a lot
i could factory reset, but after many try , i got to download mode, and i could flash ... i had realy to use the country rom, where i bought the phone, in my case , it work only whith the Colombien one....none other works, Now shall i try to flash with a cyanogène or a mui? would it works?
papilonaa said:
Thanks a lot
i could factory reset, but after many try , i got to download mode, and i could flash ... i had realy to use the country rom, where i bought the phone, in my case , it work only whith the Colombien one....none other works, Now shall i try to flash with a cyanogène or a mui? would it works?
Click to expand...
Click to collapse
There's no custom roms for Qualcomm Spirit. At least not yet.