Related
I wanted to try to run CM7 off SD card, while not changing anything with my regular boot, which is rooted stock 1.1.0.
I have followed verygreen's thread on using the size agnostic installer, and 2 different SD cards. The behavior is different on each.
on the 8 g class 6, it just boots directly to emmc, not even going to the sd card.
on the 4 g class 2, it won't boot with the sd card in. I can hold the power button till i'm blue in the face, and it won't boot.
Anybody know what I'm doing wrong?
I suspect you never got the image written properly to the card in the first place.
Someone from mobileread.com made a decent tutorial with vids, which will come up if you google "anamardoll nook cm7" (new users cannot post outside links :S ) I skipped down to "what you will need" and also skipped the first vid.
Her steps are based on verygreen and quinxy (who based his steps on vergreen).
Helped in 2 minutes. Rather than "restore virtual hard disk image" i just used the regular write image. I ended up with the same files on the sd card, but I suspect the two methods are subtly different. Thanks for pointing me to the vids.
On another note, maybe you can help me with a question. The data "apps downloaded, etc, all gets written to the SD card, right, not the internal memory? So I can have two separate enviroments, (mine on the sd card running CM7) and my wifes running rooted Nookie? With all of our data stored separately, mine on the sd, hers on the internal memory. Sound right?
Thanks!
Now I can't install Gapps! Stuck again.
Ok, not sure why I'm having so much trouble. I got the CM7 to boot, runs fine, now I'm trying to install Gapps. I downloaded the latest Gapps for Cm7, installed the zip to the SD card, booted to recovery.
It goes through all the text, then at the end looks for the gapps installer, says "installer not found" and deletes the file.
any suggestions?
Tdogg0406 said:
On another note, maybe you can help me with a question. The data "apps downloaded, etc, all gets written to the SD card, right, not the internal memory? So I can have two separate enviroments, (mine on the sd card running CM7) and my wifes running rooted Nookie? With all of our data stored separately, mine on the sd, hers on the internal memory. Sound right?
Thanks!
Click to expand...
Click to collapse
Yep, two completely separate "environments" as you call it, pull out your SD card and she has a regular Nook. All your pr0n is safe
Tdogg0406 said:
Ok, not sure why I'm having so much trouble. I got the CM7 to boot, runs fine, now I'm trying to install Gapps. I downloaded the latest Gapps for Cm7, installed the zip to the SD card, booted to recovery.
It goes through all the text, then at the end looks for the gapps installer, says "installer not found" and deletes the file.
any suggestions?
Click to expand...
Click to collapse
OK, as you have already CM7 installed fine, make sure you set up your wi-fi before installing gapps.
Now make sure you got the right gapps for the CM7/Nook from here:
http://android.d3xt3r01.tk/cyanogen/gapps/gapps-gb-20110307-signed.zip
Make sure you verify hash so that you don't have a corrupted download:
29efd1cc5457849b10d4f0dc31f7f04c
When you say "booted to recovery", how did you do it? For verygreen's installer, you need to do the two fingered salute by holding N button and power button together for approx 6 seconds.
Yes, Safe indeed!
I realized my "stupid" mistake! Evergreen's guide sends a link to the "Gapps" zip to install. When I clicked on the link, I blindly saved it, and kept trying to install it. After starting over from scratch, I realized Evergreen's link to Gapps is just another link to CM7 (hence the reason I was getting the "Gapps installer not found" message....foread slap now!)
I googled it about a half hour and got evrything working just fine!
Thanks for the link! and the help!
I have searched diligently and have yet to find specific instruction for creating a bootable SD card for my NC with MIUI Nook Color 1.9.16 (or any version of MIUI for that matter).
I am currently running a fully rooted version of 1.3 on the emmc and "all is well" and I need it left that way so as to continue having access to "in store reading" which I use quite a bit.
Have previously had CM7 and Phiremod running both internally and on an SD card at various times and tried to do a previous version of MIUI on the card using the same process without any luck.
Thanks in advance.
You can use verygreens method here -
http://forum.xda-developers.com/showthread.php?t=1000957
Important part is to rename the miui zip like this -
'How to update to a new build:
put the new build you want to try on the first partition. (the name must be update-cm-*.zip or cm_encore_full*.zip or just update-*.zip)'
..and it should work fine
cheers,
Many thanks as that did the trick!
Loaded and running from SD card.
It installed/is using the new Market interface (3.1.3?).
Where are/is "My Apps" as I do not seem to be able to find it.
D/L Netflix and it runs just as it should but the soundlevel at max is quite a bit lower than on rooted 1.3.
Free Koi living wallpaper looks beautiful.
My Apps - strangely there isn't one, but this works nicely -
http://forum.xda-developers.com/showthread.php?t=1154299
Sound level - Download nook tweaks from market and change settings in that
Cheers,
What did you rename the MIUI file? I've tried it a couple different ways and checked the MD5's, but keep getting errors. Unless my SD card has been corrupted somehow (I used it for other SD boots before this, so not too likely), I can't think of anything else causing the problem.
Hi. I tried putting the MIUI zip in the root of the sd card and booted into recovery as stated. It was renamed as one of the cm7 updates and installation went as per normal. However, when I did boot up the nook was stuck looping the MIUI animation and did not finish. What did I do wrong?
PhoenixClaw said:
Hi. I tried putting the MIUI zip in the root of the sd card and booted into recovery as stated. It was renamed as one of the cm7 updates and installation went as per normal. However, when I did boot up the nook was stuck looping the MIUI animation and did not finish. What did I do wrong?
Click to expand...
Click to collapse
Maybe just didn't wait long enough... the first boot takes a long time since the update script clears cache and dalvik cache.
Of course... this is just a wild guess since you didn't provide a whole lot of information... more information may yeild different feedback.
DizzyDen said:
Maybe just didn't wait long enough... the first boot takes a long time since the update script clears cache and dalvik cache.
Of course... this is just a wild guess since you didn't provide a whole lot of information... more information may yeild different feedback.
Click to expand...
Click to collapse
What kind of information? My nook color originally had the latest CM7 nightly on the sd card. I followed verygreen's method when I installed that. I used the NC normally. Then, I followed this thread and applied verygreen's method. I downloaded the MIUI rom from the miui thread, renamed it like the cm7 nightly zip ("cm_encore_full-253.zip") and put it in the root of the sd card. I put the sd card back in and booted via recovery. It installed and shut down. I turned it on again, and reached the MIUI globe thing. It was looping and stuck there for 30 minutes.
I've been thinking of trying miui.
If anybody has got.it running from SD please give the step-by-step procedure for the rest of us.
Thanks
A search would show you....
http://forum.xda-developers.com/showthread.php?t=1271982&highlight=Miui+sd
I hate to revive a dead thread, but I have been trying everything I could read or download.
I am using the Size-agnostic installer from this thread: http://forum.xda-developers.com/showthread.php?t=1000957
I am trying to flash MIUI 1.9.16 (MIUI.us_encore_1.9.16_Eng_Deo_ZipA_Signed_andmer) (http://goo-inside.me/miui/encore/)
I successfully installed CM7 to this Sandisk Class4 16gig microSD. Every time I try to flash MIUI, I re-burn the size agnostic card image, copy over the cm7-renamed MIUI ROM, and boot.
The installer seems to work, just like my CM7 installs. Then, when I try to reboot, it goes back to the installer (linux penguin at the top, goes through the motions of trying to flash another rom, when not finding anything, it shuts down).
I know I am missing something simple.
Am I to install CM7, then MIUI on top of it (without reburning the card)? Am I just using an SD-incompatible ROM? For those who were successful, where did you download the ROM from?
I know I have lots of questions, I hope you guys see my effort (that I don't just want someone to give me a quick fix), and I thank you in advance for your help.
Kind regards!
harryzee said:
Many thanks as that did the trick!
Loaded and running from SD card.
It installed/is using the new Market interface (3.1.3?).
Click to expand...
Click to collapse
I'm certainly no expert, but I have flashed two different versions of MiUi to micro SD cards adn then worked fine. You do not need to do i over CM7. Like you, I prepared a clean SD and used the size agnostic procedure. I renamed the MiUi file to some that started with update-cm-
I got my MiUi file here:
http://roms.miui.us/
I used a program called SD Formatter to format the card.. then I used the 1.3 version installer. I sometimes had problems using winimage to create this sd card . You have to select the drive letter for the sd card and then use the "restore" choice on the menu.
David, thanks for your response. I had already wiped it and installed CM7, but when I saw your post, I gave MIUI one last try. I downloaded from that site, and BAM, it installed perfectly! Thanks heaps!
Ok, I have run this install method 2x today http://forum.xda-developers.com/showthread.php?t=1000957&highlight=verygreen+sd+bootable *VeryGreen*
Now, I am not new to rooting but haven't been keeping up with my nook as I passed it on. Went from CM7 stable to MIUI couldnt' stand the market issues and didn't want ot deal with removing the up dater..blah blah blah ok enough of that
I have followed the instructions and was have booted CM fine but each time I look at my SD card I only have the one partition. Should I be partitioning it myself before doing the steps metitioned or should the install make the partions for me then I just write the FAT or FAT32 (<---top of my head) myself post install.
I wanted a dual boot but figured I would wait for CM9 to come out and wanted to test the SD install. Also, the system seems laggy and I would attribute that to the card i'm using but was also wondering if maybe it was from the partitions? I believe the card is only showing 120 mb used and 14 unused.
Thanks, for any help I have been working on this for 3 days different scenerios and used searches but I get so many dated threads.
~D
If you are using windows you will only see the first partition.
Sent from space
That would be why, hadn't thought about that but was going to into partitioning i myself this evening in linux either would have seen this or been worse for the wear. Thanks, seems it's still not running as smooth and I am thinking it' the card, I'll just got with old faithful for now and work on it more after NYE have a trip coming up and would rather have it in state I know works.
Cheers
UPDATE 05/28/13 - Now that verygreen has changed his SD scheme to his new version, this guide should not be used on his ROMs dated 5/27 or newer. Use his new image and follow his new instructions. If you want to see the old instructions click on the Show Content button below.
Click to expand...
Click to collapse
Many users have had difficulty installing the HD+ CM10/10.1 ROMs using the Original/Legacy (verygreen) SD setup (especially Windows users). I have written this guide and have made some tools that should make it easier. No need for ADB or Linux. I have upgraded the CWM (clockworkmod) recovery to version 6.0.2.8 which includes larger fonts, a brighter screen and the ability to use the internal storage for installing zips and performing backups. It also uses verygreen's process from his early4 zip that aligns partitions at 2M. This guide and tools are for the Original/Legacy SD setup by verygreen, not the Hybrid. If you want the Hybrid, go here.
Setting up the SD
Begin by downloading the files you need either with stock or your PC. You will need my updated SD image file, attached below (do not use the early4 image from the verygreen thread), the CM ROM zip you want to install and the gapps zip to match it. Put the last two zips on your internal media sdcard built into the HD+. You can get the HD+ CM10 ROMs here and the HD+ CM10.1 ROMs here. You can get the gapps zips here, 20121011 for CM10 and 20130301 for CM10.1.
Extract the SD image zip and you will have a 117MB .img file. Burn that to your SD with Win32DiskImager in Windows or the dd command in Linux or OSX. The SD needs to be at least 4GB and preferably a SanDisk Class 4.
To use Win32DiskImager, find it on the web (here, it's free) and install it on your Windows PC. Open it (be sure to run it as administrator) and select the drive (device) that has your card reader with your SD inserted. Then in the image file box put the location where you have the extracted img file. Then when everything is set right, click on the write button. A warning will pop up asking if you want to proceed. When you have verified that you are going to write to the correct device, click on Yes. (One user overwrote their external USB hard drive by not verifying first.) If you get an error message about access denied, it means you are looking at the drive with Windows Explorer. Close Windows Explorer and try again. In fact, it is a good idea to close all unnecessary windows when burning, even your browser.
When burning is complete, insert the SD into the Nook and boot. It should boot to the cyanoboot logo and sit there for a little while while it creates the other partitions on the SD and formats CM10SDCARD. Then it will end up in CWM for HD+ Original SD. If it does not leave the cyanoboot logo within a reasonable time (it hangs sometimes), just touch the power key and CWM should come up. To use CWM, press the volume up/down keys to move the cursor and the n key to select an item. The power key is the back button.
Installing ROMs
You can use the "install zip from SD/choose zip from internal memory" option to flash the CM ROM you downloaded earlier to your internal memory sdcard. Then you can flash the right version of gapps to match your ROM.
When you reboot (you need to leave the SD in the slot), the CM ROM should start. You will need to register with Google to set up Play Store.
If you later want to upgrade your ROM to another build, download it to your CM10SDCARD partition using CM. Then boot to CWM and flash it.
Backing Up
This version of CWM lets you back up and restore your setup. You can even back up to internal memory. It does not back up /boot, but does back up /system, /data and /cache.
Swapping EMMC and SDCARD
Some users have installed CM to a small SD card and want their apps to use the large internal media storage to store their data. I have developed a couple of zips to swap EMMC and SDCARD when booted to CM so that internal memory is available to your apps to store their files. One zip will add the swap and one will remove it. Get them attached below.
These zips can be flashed with CWM but will only install to the Original SD with CM. I just fixed a bug in the rev0 and rev1 zips. If you already flashed rev0 or rev1, you need to flash the remove zip before you flash the rev2 fixed version. No need to boot in between.
With rev2, both SDCARD and EMMC will show internal media storage, as will both MTP folders. A new folder, ext_sdcard, will show the external SD media partition.
Updating earlier versions of CWM
Updating prior installs of the Original SD installation to this new version of CWM is easy. Just download the ramdisk zip file attached below and extract the file. Put your old SD setup in your PC and rename the ramdisk.cwm to ramdisk.cwm.bak. Then copy the new ramdisk.cwm you just extracted to the card, replacing the version that was there. Next time you boot to CWM, the 6.0.2.8 version for HD+ Original SD will be there.
Change Log
Change Log
05/28/13 - guide is obsolete starting with the 5/27/13 ROM
05/15/13 - removed warning, resolved
04/10/13 - added warning running CM10.1.
03/09/13 - added rev2 of the swap zip, as it failed on CM10.1
03/08/13 - added rev1 of the swap zip to fix a permissions bug.
03/07/13 - retitled thread
03/03/13 - added CM10/10.1 SDswap zips
02/27/13 - Initial posting
OP Updated
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
For hd plus only?
Sent from my BNTV400 using xda app-developers app
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
mrDAXpax said:
For hd plus only?
Sent from my BNTV400 using xda app-developers app
Click to expand...
Click to collapse
Yes, you can use bokbokan's hybrid image to do it the same way for the HD. And I think his standard image does it too.
Sent from my Nook HD+ running CM10 on Hybrid SD
question...
Sorry if this has been answered somewhere else but, I did this using a 32gb card and everything I running smooth. I have a 64gb card that I want to switch it out for. I know it won't be a problem doing the root and all of that again, but I was wondering if anybody knows how to change the 32gb SD card back to normal? When I stick it in my computer all it shows is the boot partition and when I try to format it, it only formats that's partition. Meaning that my 32gb card turns into a worthless 116 mb card. I've tried on windows and Ubuntu and get the same results...
So does anybody have any suggestion?
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
startoxic said:
Sorry if this has been answered somewhere else but, I did this using a 32gb card and everything I running smooth. I have a 64gb card that I want to switch it out for. I know it won't be a problem doing the root and all of that again, but I was wondering if anybody knows how to change the 32gb SD card back to normal? When I stick it in my computer all it shows is the boot partition and when I try to format it, it only formats that's partition. Meaning that my 32gb card turns into a worthless 116 mb card. I've tried on windows and Ubuntu and get the same results...
So does anybody have any suggestion?
Click to expand...
Click to collapse
Yes, use SDFormatter free from the web. It will do it.
Sent from my Nook HD+ running CM10 on Hybrid SD
Thank you, I will try that and let you know how it works
This is probably a stupid question, but once I've got the SD card set up properly, can I then go ahead and delete the ZIP files that I've installed? Or do I need to keep them kicking around? Figure if I can free up some space, I should.
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
stormerider said:
This is probably a stupid question, but once I've got the SD card set up properly, can I then go ahead and delete the ZIP files that I've installed? Or do I need to keep them kicking around? Figure if I can free up some space, I should.
Click to expand...
Click to collapse
You can delete them if you want, but I usually always keep them somewhere so I don't have to redownload them if I need to reflash, which very oftern I have to for various reasons. I can always delete them later if space becomes an issue.
Sent from my Nook HD+ running CM10 on Hybrid SD
leapinlar said:
You can delete them if you want, but I usually always keep them somewhere so I don't have to redownload them if I need to reflash, which very oftern I have to for various reasons. I can always delete them later if space becomes an issue.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
*nod* I meant deleting them off the SD card (should have specified). I'd be keeping them on my fileserver to ensure that I can reflash the sdcard to the same version I started with if I need to.
leapinlar said:
Setting up the SD
Begin by downloading the files you need either with stock or your PC. You will need my updated SD image file, attached below, the CM ROM zip you want to install and the gapps zip to match it. Put the last two zips on your internal media sdcard.
Click to expand...
Click to collapse
I'm confused by this, what are you referring to as "internal media sdcard"? I used win32 to burn the .img file, then booted into CWM...I'm clearly doing this wrong, because after that, the sdcard only has 117mb and no room to put ROMs on
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
KamikazeChris said:
I'm confused by this, what are you referring to as "internal media sdcard"? I used win32 to burn the .img file, then booted into CWM...I'm clearly doing this wrong, because after that, the sdcard only has 117mb and no room to put ROMs on
Click to expand...
Click to collapse
You are doing it right. 117MB is what it is supposed to have. You do not put the files on that card. You put them on the HD+ (on the internal sdcard).
If you could see that it only had 117 MB, you were not booted to CWM, you were looking at the SD while it was still inserted in the PC. Booted to CWM means it is in the Nook.
When you insert the burned SD into the powered off HD+, then turn it on, it boots to CWM. That is what I mean by booting to CWM.
The internal sdcard means the storage that is built into the HD+ (that is why I call it internal). Boot to stock and download the files with it. They get put on the internal sdcard or "sdcard" as it is called. After you insert the burned card into the HD+ and boot to it, CWM has the ability to flash the zips by reading them from the internal sdcard built into the HD+.
Edit: I just clarified that in the OP. It is hard to anticipate how users will interpret your words in advance.
Sent from my Nook HD+ running CM10 on Hybrid SD
i dont seem to understand what file is supposed to amount to about 120mb. i extract "cm-10-20121231-UNOFFICIAL-ovation" and amounts to more than 200mb's but it also replaces other files.
Re: [GUIDE/TOOLS] HDplus CM10/10.1 Easy Install Guide and Tools for Original SD
droidbot1337 said:
i dont seem to understand what file is supposed to amount to about 120mb. i extract "cm-10-20121231-UNOFFICIAL-ovation" and amounts to more than 200mb's but it also replaces other files.
Click to expand...
Click to collapse
You do not extract the cm zip. You extract the image zip which is attached to the post. It is the one that is 120 MB and is the one you burn to the SD with win32diskimager.
Sent from my Nook HD+ running CM10 on Hybrid SD
leapinlar said:
You do not extract the cm zip. You extract the image zip which is attached to the post. It is the one that is 120 MB and is the one you burn to the SD with win32diskimager.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
thank you for the help. i appreciate it! i can now use my new HD+ (bought it last night) to its full potential.
I just wanted to say that I was suffering from the dreaded "Nook refuses to boot from the SD card" syndrome. I tried three different SD cards burned using four different computers, to no avail. Tried this patch? Worked perfectly. Thanks! :laugh:
SDXC cards viable for this use?
Well, that registration video was a real interesting bit compared to most forums I've ever used. Somebody put a lot of work into that.
I'm noticing a lot of emphasis on Class 4 cards. Impetuous sort that I am, I already obtained a Sandisk Ultra 64 GB microSDXC (Class 10/UHS 1) card for this project. Best Buy had a good deal and I was hoping to have a lot of room to work with and it wasn't clear what access to the internal storage would be available or best left alone. Has anyone had success or great problems with this card?
Other than that issue before attempting to execute the install, this is a very helpful thread. Much clearer than verygreen's original. That shouldn't be taken as an insult to verygreen as technical writing for those outside a project is not a skill everyone has or should have. Asking those deep within a project to shift mental gears to operate at the outsider's level can be a waste of resources and is often better delegated to a specialist. And we should be thankful for those specialists when they volunteer like this.
Epobirs said:
I'm noticing a lot of emphasis on Class 4 cards. Impetuous sort that I am, I already obtained a Sandisk Ultra 64 GB microSDXC (Class 10/UHS 1) card for this project. Best Buy had a good deal and I was hoping to have a lot of room to work with and it wasn't clear what access to the internal storage would be available or best left alone. Has anyone had success or great problems with this card?
Click to expand...
Click to collapse
Some have had good success with that card, especially if they use my Hybrid setup which uses less of the SD to operate from.
leapinlar said:
Some have had good success with that card, especially if they use my Hybrid setup which uses less of the SD to operate from.
Click to expand...
Click to collapse
It appears to be working on the first try. I'm currently syncing my app set from the Play store. It looks like this will be a huge value add for the Nook. I wouldn't have bought it if the full Android option weren't there. I just hope enough of us still buy books from B&N to keep them going.
Thanks.
Hi all, so to start with, as the title says im constantly running out of space on the FN model 2015, so ive dived into the forum looking for help. First thing i tried was the sd card hack to combine my 64gb sdcard with the 8gb internal. Harra! it worked, but then i still run outa space as it dosen't seam to to use the sdcard space as i had hoped. It's like it just copys some of the data from the apps to the SD card like normal but without having to go into the each app and selecting external sdcard. Kinda thought no probs I'll download a custom rom with no samsung apps and with a min gapp giving me as much storage space i could get. I can't see one, starting to think there isnt one. So my question is, is it hard for me to take my backup of my stock rom and strip what I can out bearing in mind I'm a bit of a noob and have to follow instructions from the clever ROM makers? not to bothered about increasing the speed and looks just the space. Would be able nice to update them without having to delete a few and re-install the ones I deleted. Any advice on what coarse to take would be great. Maybe theres a ROM I've mist I could use and give thanks for?
Cheers
Running 6.0.1
Drebbs
Hi,
Instead of using Adoptable Storage, make 2 partitions on your SD, 1 FAT32 for photos,music,documents and another EXT4 for apps data. Use this app: https://play.google.com/store/apps/details?id=in.co.pricealert.apps2sd , i tested it.
You can make 2 partitions using PC or with TWRP Recovery.
drebbs said:
Hi all, so to start with, as the title says im constantly running out of space on the FN model 2015, so ive dived into the forum looking for help. First thing i tried was the sd card hack to combine my 64gb sdcard with the 8gb internal. Harra! it worked, but then i still run outa space as it dosen't seam to to use the sdcard space as i had hoped. It's like it just copys some of the data from the apps to the SD card like normal but without having to go into the each app and selecting external sdcard. Kinda thought no probs I'll download a custom rom with no samsung apps and with a min gapp giving me as much storage space i could get. I can't see one, starting to think there isnt one. So my question is, is it hard for me to take my backup of my stock rom and strip what I can out bearing in mind I'm a bit of a noob and have to follow instructions from the clever ROM makers? not to bothered about increasing the speed and looks just the space. Would be able nice to update them without having to delete a few and re-install the ones I deleted. Any advice on what coarse to take would be great. Maybe theres a ROM I've mist I could use and give thanks for?
Cheers
Running 6.0.1
Drebbs
Click to expand...
Click to collapse
Hey i recommend rooting ur phone then download an app called move to sd card from playstore go to settings and choose download locations then select external sd card . Problem solved
Sent from my SM-J500F using Tapatalk
read post #415
here: http://forum.xda-developers.com/gal...msung-j5-f-t3400101/post69989096#post69989096
Thanks for your reply! I went down the apps2SD route in the end. Kinda mest it up a bit but have free'd up nearly 1gb of space so thanks, that's more than enough! %) I ended up partitioning the SDcard and linking all the apps I'm not interested in, excel,Skype,Samsung etc. Anyway what i didn't realise was that i had mest the other part of the partition up. Ended up re-formatting the SDcard in recovery back to normal and those apps I didn't want 90% of the data of those have now been wiped %)