Related
Hey,
I was trying to load some gapps on my sprint htc hero (running AOSP rom) and It wouldn't work so i followed some instructions online and somehow my phone is bricked... I can go to clockwork but when i try to install a zip it goes all the way to installing package then it just goes back to the home screen of the recovery. There's no ROM running at all anymore because i tried formatting everything to start over but the same thing happened. Could someone plz help!!!
Thanks!
UT_PLAYA1 said:
Hey,
I was trying to load some gapps on my sprint htc hero (running AOSP rom) and It wouldn't work so i followed some instructions online and somehow my phone is bricked... I can go to clockwork but when i try to install a zip it goes all the way to installing package then it just goes back to the home screen of the recovery. There's no ROM running at all anymore because i tried formatting everything to start over but the same thing happened. Could someone plz help!!!
Thanks!
Click to expand...
Click to collapse
Ok...Your phone is not bricked because it is turning on. There are very few things that you can do to actually brick this phone. However before anyone can be of much assistance you are going to have to provide some more detailed information about your problem. I would also suggest that you check this thread that Il Duce posted in the Q&A section.
http://forum.xda-developers.com/showthread.php?t=1063843
Lastly I'll assume that your bootloader is S-On which means if you do not have adb set up on your computer yet you should do so, because it sounds as if you MAY need it at some point.
have you tried flashing a rom? Iv had the same problem and figured that wiping everything, then flashing a new rom fixed it
Boom... Headshot! from my L96A1
Try reflashing your current recovery threw adb. Might help.
#Root/Hack-Mod_Always*
laie1472 said:
Try reflashing your current recovery threw adb. Might help.
#Root/Hack-Mod_Always*
Click to expand...
Click to collapse
i agree with laie1472. reflash your recovery. it will give you a clean start. let us know how it goes.
ok so in more detail.... I turn on my phone and it just loads the HTC screen and goes on forever because there's no rom to load. So i can boot it into clockwork recovery, and when i get there i wipe data/factory reset and also wipe cache partition, then i try to install zip from sdcard. I go to choose my zip and click yes and as the script is running across the screen it goes like this: Finding update package.... Opening update package... Installing update package... then it just goes back to the clockwork recovery screen (with the options like reboot system, apply sdcard:update.zip, etc.) sorry i don't know that much about this but i can learn fast.
Thanks!
Ok. So have you tried to reflash your recovery??? Try it threw adb. If you don't have adb setup check out the link hockeyfamily posted for duces thread. Once there look for my thread on how to install adb. It takes like 15 to 20 min tops. If you need help with the guide just post here or send me a pm. Hopefully this helps
#Root/Hack-Mod_Always*
Kind of where I was headed with the "setting up adb" part of my first answer.....but the op never stated how many different roms he tried or if he tried to restore a nand.
Sent from my.....click, click, boom
I tried using aosp rom and CM7. I can't load the other recovery because in your instructions it says I need easytether. I can't load a rom so i can't download that from the market.
You need "adb" which is installed on your pc, not on your phone.
Sent from my.....click, click, boom
ok... sorry really kinda new to this. But once i have adb installed on my pc where do i go
I have tried to install, following instruction on this site to install ROM's. I have tried Starburst and Task650. I currently have the OTA Touchwiz installed from Samsung, and Pershoot kernel 2.6.34-4-cyanogenmod installed. Every time I try it goes through the process and successfully I reboot, it boots to the Samsung Logo (Start) and I wait like 20 minutes and it does nothing, just stay at the start Samsung logo. I have done this several times on each ROM, always having to go back to a backup I did. What am I doing wrong? Why can’t I install any ROMs? I would greatly appreciate some expert advice, because I hear so many great things about Task650 I really want to give it a shot. I am an ex-iPad owner, gave to daughter as a friend had one and let me use it; feel in love with it the moment I picked it up. I have also searched the forums, but I am doing everything to the T as outlined in instructions. Had my tab for a week, it isn’t a 10.1v or I/O series. Thanks everyone in advance for helping a complete noob when it comes to android.
Sounds like a case of missing to clear the cache.
Did you wipe the cache partition and dalvic cache in the recovery menu?
After making major changes like switching between roms or kernels thats recommended and if not done might cause such an issue.
I did
I did do those steps, did the factory wipe/reset, wiped cache, wiped dalvic. Once I did those 3 steps, installed from zip, goes through the steps successfully, but when I reboot it just stay on logo. I read, it could take 5-10 min, but I have waited up to 20 and it doesn't move past that. Just see what I am doing wrong, as the 2 roms have both done that, and I have tried several times with both. Just have the stock rom with Touchwiz OTA upgrade from Samsung, and pershoots latest kernel. Thanks in advance.
bad zip file?
Is it possible the zip files are getting corrupt? Are you downloading them on your tab or on computer and transferring them over? I would also check to see if there are any errors when you flash.
Download from computer and transfer over. How can I if there are errors as once I install a ROM it just stays at the logo. After it starts to install it end with, i cant recall exactly, but it says success. Thanks in advance
In cwm when you flash there is some text readout. That is where some error messages could be seen. That text will be there before you choose reboot on the menu.
sounds like you've had some issues bro. if you do get fed up and need some help, just let me know and we can video chat through gmail or skype to get you through it and get you a custom rom.
slice2011 said:
I have tried to install, following instruction on this site to install ROM's. I have tried Starburst and Task650. I currently have the OTA Touchwiz installed from Samsung, and Pershoot kernel 2.6.34-4-cyanogenmod installed. Every time I try it goes through the process and successfully I reboot, it boots to the Samsung Logo (Start) and I wait like 20 minutes and it does nothing, just stay at the start Samsung logo. I have done this several times on each ROM, always having to go back to a backup I did. What am I doing wrong? Why can’t I install any ROMs? I would greatly appreciate some expert advice, because I hear so many great things about Task650 I really want to give it a shot. I am an ex-iPad owner, gave to daughter as a friend had one and let me use it; feel in love with it the moment I picked it up. I have also searched the forums, but I am doing everything to the T as outlined in instructions. Had my tab for a week, it isn’t a 10.1v or I/O series. Thanks everyone in advance for helping a complete noob when it comes to android.
Click to expand...
Click to collapse
Well first...are you rooted? Do you have Clockworkmod, Superuser, and Busybox?
Oh and congrats on your switch from Apple to Android
slice2011 said:
I have tried to install, following instruction on this site to install ROM's. I have tried Starburst and Task650. I currently have the OTA Touchwiz installed from Samsung, and Pershoot kernel 2.6.34-4-cyanogenmod installed. Every time I try it goes through the process and successfully I reboot, it boots to the Samsung Logo (Start) and I wait like 20 minutes and it does nothing, just stay at the start Samsung logo. I have done this several times on each ROM, always having to go back to a backup I did. What am I doing wrong? Why can’t I install any ROMs? I would greatly appreciate some expert advice, because I hear so many great things about Task650 I really want to give it a shot. I am an ex-iPad owner, gave to daughter as a friend had one and let me use it; feel in love with it the moment I picked it up. I have also searched the forums, but I am doing everything to the T as outlined in instructions. Had my tab for a week, it isn’t a 10.1v or I/O series. Thanks everyone in advance for helping a complete noob when it comes to android.
Click to expand...
Click to collapse
Maybe try in "reverse" order
Flash kernel back to stock - flash the rom you want - if that works then flash pershoots kernel
Just a thought
hy
i installed the overcome rom on my 7500, and i'm so entusiast!
Try it it's very easy!
---------- Post added at 07:21 PM ---------- Previous post was at 07:16 PM ----------
i did it in recovery, do wipe data
Yes its is rooted, cmw, superuser, and busybox all installed. Installed both roms in recovery, hold volume down and power method. Just can't figure it out, I will do the reverse suggestion and report back later tonight or tomorrow.thanks everyone for the advice/help.
no erreor s after install, think task's says success or something to that effect.
Well it finally stuck, I knew it was going right as when it was installing system files, it took like 5 minutes, the other time I did it took like 30 seconds. As per Stinky73 went back to stock Kernel, and wipe data, clear cache partition, and wipe Dalvik Cache, Thanks a million Stinky73 u da man! HELL YEAH this Rock, it is so responsive, seems a hell of a lot smoother, and apps just snap open. Task you did one outstanding job. This is coming from a noob who has no idea how much work goes into these, I am sure a lot. So from a noob to an expert EXCELLENT JOB, love my Tab that much more!!!!! Thanks everyone for the help, I am one happy camper! Now another dilemma, I saw new versions: How do I install these now that I have Tasks650 installed and working? Do I have to do the same steps above, wipe data, cache, and Dalvik? And if so what do I do next, do I do the same: Also is the BOB_WOW_Fix installed using the same method as i read flashable, sorry for the noob question, just want to get it right.
1. install zip from sdcard.
2. choose zip from sdcard.
NEW!!!- Task650's V7.1
Once again... I forgot to add "Desktop UAstring to V7.1 so flash this update after you boot up V7.1 if you want it.
Can someone please give me the proper ateps on installing the bob_wow_fix, and the 2 7.1 updates? Thanks
slice2011 said:
Can someone please give me the proper ateps on installing the bob_wow_fix, and the 2 7.1 updates? Thanks
Click to expand...
Click to collapse
There's no complete fix for BoB and WoW, its a continuous work in progress.
bob wow fix
Are you taking about the fix task posted?
What I had to do was wipe cache first then flash the zip just like you did on the rom. And bobs your uncle.
Edit:
Oh ya I would reboot after each flash just to be sure.
So as you probably read had a hell of a time getting a rom installed, followed stink'ys advice and it worked. Installed 6.0, finally, than installed the 6.1 theme update, no issues. Than downloaded the 7.1, followed op. wiped dalvik, wiped cache, and wipe data/factory restore. No errors, but when I rebooted it got stuck once again on the Samsung logo with the Galaxy Tab 10.1 print. So i do not know what the heck I am doing wrong. I got 6.0 than 6.1 updated and now I am back to my initial problem with 7.1, no I didn't use the 7.1 update one. tried 3 times, and even downloaded the fiel again, and followed the same steps task outlined, and no go. Had to restore the 6.1 from back up.
slice2011 said:
So as you probably read had a hell of a time getting a rom installed, followed stink'ys advice and it worked. Installed 6.0, finally, than installed the 6.1 theme update, no issues. Than downloaded the 7.1, followed op. wiped dalvik, wiped cache, and wipe data/factory restore. No errors, but when I rebooted it got stuck once again on the Samsung logo with the Galaxy Tab 10.1 print. So i do not know what the heck I am doing wrong. I got 6.0 than 6.1 updated and now I am back to my initial problem with 7.1, no I didn't use the 7.1 update one. tried 3 times, and even downloaded the fiel again, and followed the same steps task outlined, and no go. Had to restore the 6.1 from back up.
Click to expand...
Click to collapse
All sounds very strange...is it definitely stuck on the boot screen? These things can take anything from 5-20 minutes on initial boot, there is no definite rule for that, seems to be device related in some strange way...how long have you left it?
I am really an OCD when it comes to upgrading and always backup (nandroid or whatever) then go back to the very start before trying something new...years of PC and Mac have taught me that even tho the manufacturers say you just apply upgrades on top of previous upgrades, sooner or later they will f**k up....
I wonder why you are passing thro all the steps you are...(going thro 6.0, 6.1 etc)
I would be inclined to try going back to stock....stock whatever it was rom when you got the tab (notice you've never stated what model you have), stock kernel, nothing installed....then go direct to Tasks 7.1 (everything needed in 6.x is incorporated in 7.1) .... then, if it boots and runs, add pershoots kernel...
What do you reckon Task?? Can you chip in on this one?
Cheers, Stinky
@ slice2011.....any news?
Drpbody said:
And bobs your uncle..
Click to expand...
Click to collapse
How'd you know Bob was my uncle?
Oh wait..everybody has an uncle bob somewhere
i dont know if im asking for help to the right person but if you can help me tank you very much.
today i tried to restore my nook color by pressing u button and power and he goes to the factory reset asks to press u button and i press then he asks again and i press and after the yellow bar moves too fast only last about 3 seconds and it should take some minutes and after reboots. i think my factory partition in damaged.
;(
Don't get too upset. You can still boot from SD. At worst, you may have to (re)install some firmware. If you want the B&N firmware, you can reinstall B&N 1.3 and update, or stay at 1.3 if you prefer.
It's hard to totally brick a NC.
Take a look at the restoring to stock section of the guide in my sig
Sent from space
Listen to the two people above this post. They are right. It is nearly impossible to completely brick it. Trust me I've tried.:what:
Seems no matter what I do to it, short of kick boxing it, I've always been able to start from a brand new running nook. Just by reading many posts and the great help from everyone on this forum, who have usually, "been there, done that.", folks.
I'm sure this will work out and everything will be fine, but then you'll be able to help someone else too.
Sent from my GT-P7510 using Tapatalk
i just use this command "fdisk /dev/block/mmcblk0 -l"
i think it was to see the partitions and they dissapeared just chek the image ;(
I think what you are looking at there is the partitions on a booted SD card which look correct for an 8GB card.
bobtidey said:
I think what you are looking at there is the partitions on a booted SD card which look correct for an 8GB card.
Click to expand...
Click to collapse
Nope... you can see he's looking at /dev/block/mmcblk0... that is internal.
Need to find the thread about the nook color partitions and create partitions 5-8 then dd the images to them.
i already fixed ! its working again
i can´t believe,
i was thinking about doing a tutorial in how to soft unbrick your nook, i´m not an expert but is a lot of people with the same problem as mine
basically when i enter in recovery receive errors in logs and he dont let me mount or format any of mine partitions(except boot and sdcard), a lot of people are having the same issues and i was thinking about doing a tutorial in how to do it.
should i do it??
thanks everybody
More tutorials are always good. One thing to remember though, is that if someone is looking for a tutorial that means they are usually starting with a small knowledge base. You not only need to be clear, you need to be right.
All I am saying is an underinformed/incorrect tutorial is worse than no tutorial at all. The information is out there, but can be hard to find. If you know your stuff, and have a place to present it where it doesn't already exist, then sure, people will benifit from your knowledge.
Just a guess, but problems mounting within CWM tend to come from old and/or incompatible versions of Clockwork. Is that where you had your problem? I definitely wished that had been stressed on the tutorial I first followed. Would have saved me untold hours of pointless reflashing.
you are right but in my case and i think that is the same of a lot of people (who follow this tutorial http://www.youtube.com/watch?v=szlGSBtWbKY) i tried about 7 to eight diferent versions of clockworkmod and including change of sdcard, i also tried DD the images of the boot and system, when nothing of this works we start get in panic, with no necessity because its only a partition problem, i fixed my 4 partition and he started working
Yeah, I can see where you are coming from. I followed an older tutorial as well, and never saw anything to indicate the link to the CWM image might be outdated.
For sure, that info should be wider spread.
Good luck on your video (?)
hackerse7en said:
i dont know if im asking for help to the right person but if you can help me tank you very much.
today i tried to restore my nook color by pressing u button and power and he goes to the factory reset asks to press u button and i press then he asks again and i press and after the yellow bar moves too fast only last about 3 seconds and it should take some minutes and after reboots. i think my factory partition in damaged.
;(
Click to expand...
Click to collapse
I am not sure where to ask for help. I have been updating the CM9 nightly for a while, didn't have any problem. But when I tried to flash 02-17 nightly, I messed up and in the middle of the install, I power off forcing to reboot. Now, it keeps going loop back to the CW recovery screen every time I tried to reboot.
--
I tried to reinstall the whole thing with the boot-able sdcard, but didn't work. Am I bricked my nook?? please help! someone?
I tried to wipe, reformatted the system, data, cash, boot. Still stacked at the cw recovery screen. Help...
I've finally lost patience with my TF101 boot looping and being flat when I come to use it. Asus clearly aren't in a rush to fix it, and I can't find an alternative tablet that I'm happy to replace it with right now, so I've decided to give guevor's version a go.
The problem being that I've read a load of threads on rooting a TF, but still haven't come to a conclusion on which method actually works for a WW one on 9.2.1.17, if there even is one!
So any chance some one could help me out and point me in the right direction? Thanks
Use Vipermod to root. Search the forum for link.
Thanks, I'll take a look.
Just wanna check my list with you experienced guys before getting stuck in, mostly because it's been a while since I did anything like this and I can't find a thorough guide for the whole process.
1. Root with vipermod.
2. Install ROM manager from the market and use to flash CWM recovery.
3. Boot into CWM recovery and make backup.
4. Copy kernel .zip file to storage of the TF.
5. Boot into CWM recovery and select install .zip option.
6. Enjoy new kernel and hope for no more bootloop/flat battery scenarios making me angry?
Correct, except you shouldn't use apps like Rom Manager to do things that you can easily do yourself. Don't blindly flash whatever Rom Manager tells you to because sometimes it will screw up your tablet. Haven't you read all these threads about people having problems because of ROM manager?
Just use the recovery installer apk by Gnufabio. It will flash a slightly outdated CWM but it works without problems and you can update it yourself by downloading and flashing a newer CWM posted on this forum.
I can confirm viper for root, and gnufabio recovery installer.apk. I just went through the process last night. If you do not use gnufabio you will spend hours trying to get cwm on your device, and failing.(2 hours of dead androids in recovery) wish i had seen gnufabio sooner.
Edit: also theres a remixed viper out there supposed to be a 1 click root
http://forum.xda-developers.com/showthread.php?t=1534475 is the link
Also i suggest the touch cwm from
http://forum.xda-developers.com/showthread.php?t=1213723
It works very well and all touch so no need to press physical buttons.
Thanks for the input guys, it's very much appreciated.
I haven't seen the threads on problems with ROM manager. I've just been searching for specific terms and TBH I find this forum generally difficult to find up to date information. It's very time consuming searching and reading lots of nothing posts. The TF info threads have a lot of links to outdated guides (or ones that lack detail as they assume you know everything already ) and a lot of the shortened terminology that's used is confusing unless you visit here. I've read as much as I can, but I wanted to be sure I had the right information before trying out something that could render my tablet useless.
Typical, fallen at the first hurdle!
"hold volume down and power for 3 seconds, let go of power only, then press volume up when prompted on screen" just results in a screen with an Android with a red triangle on his chest. More extensive searching needed I suppose.
lol nope this is my problem i told you about in earlier post
get the recoveryinstall.apk by gnufabio install it on your tf and run it. it installs a working cwm then you can do the touch cwm,kernel rom etc after that
gnufabio installer link
http://forum.xda-developers.com/showthread.php?t=1346180
Oops, yeah sorry that passed me by some how! Busy day.
Thanks again!!
no problem bro thats what we are here for to help you catch those moments when your about to bash your head against the wall and say "oh hey didnt you see this..." and make you slap your forehead instead.
Finally got around to doing this. All OK so far, got it rooted and touch CWM installed but I'm a bit unsure about what caches and stuff I should wipe. Do I need to do both wipe data/factory reset AND/OR wipe cache partition in the touch CWM recovery before flashing the new kernel?
wolvers69 said:
Finally got around to doing this. All OK so far, got it rooted and touch CWM installed but I'm a bit unsure about what caches and stuff I should wipe. Do I need to do both wipe data/factory reset AND/OR wipe cache partition in the touch CWM recovery before flashing the new kernel?
Click to expand...
Click to collapse
I ALWAYS do a full wipe, dalvik cache the lot when flashing a different ROM, if you're just flashing a new kernel no need for wipe data just dalvik cache
Thanks for the reply. I found some posts last night where peeps were not wiping anything so I just flashed the 16b test kernel. Seems to be all OK so far.
I have the same issue...no recovery. Ive downloaded the gnufabio recovery file from the link, however i was expecting an .apk file that could be installed from the tablet OS desktop maybe usinf File Mgr. What the link downloads is a .zip w/ some folders and asstd files. Everyone is referring to it as an apk...Im confused.
fwbflash said:
I have the same issue...no recovery. Ive downloaded the gnufabio recovery file from the link, however i was expecting an .apk file that could be installed from the tablet OS desktop maybe usinf File Mgr. What the link downloads is a .zip w/ some folders and asstd files. Everyone is referring to it as an apk...Im confused.
Click to expand...
Click to collapse
It should be an apk. Did you use the link in his thread?
I have links to the apk in post 218 also including a modified version that will flash Team Rouge recovery.
http://forum.xda-developers.com/showpost.php?p=22359727&postcount=218
Thank you very much for those links...yes, those were apks. I have been looking for those links for sometime.
flashed the RecoveryInstaller.apk, giving me a recovery system to work from, now Im restored, rooted, ROMd and OC'd...thanks for the links!!
Since rooting mine, flashing the 16b kernel and OCing to 1600mhz it's been completely stable and fast. I just hope that continues!
Thanks everyone for your kindly assistance.
im trying to put a recovery on my vibrant that i have and i have root access but when i try to intall rom manager so i can get the recovery i do not find it in the app store. i still have the OLD app store that has lots of green borders. When i look for rom manager, i find te paid version but not the free version and when i try manually installing the apk...
it says parsing error. can i get some help wth the please.
Not sure, but here is the direct downloaded ROM Manager (free)
http://www.mediafire.com/?523y13j76z66lb7
Thanks for the download.
I tried installing it but it did the same thing. It said parsing error
Download cwr from my signature. Put update.zip on your internal and make sure it is only thing labeled that on there. Boot into stock recovery (blue) and hit Reinstall Packages, let it cycle, hit it again and stock (blue) now becomes cwr (green) and flash away
Woodrube said:
Download cwr from my signature. Put update.zip on your internal and make sure it is only thing labeled that on there. Boot into stock recovery (blue) and hit Reinstall Packages, let it cycle, hit it again and stock (blue) now becomes cwr (green) and flash away
Click to expand...
Click to collapse
will do but is it safe to do this if i rooted with zRoot and if i am on stock rom 2.1-update1
Yes that is the best way as a matter of fact. Btw what ROM are you wanting to flash?
i want to get any form of ICS on the vibrant, if yo could also help me with that i would greatly appreciate it.
lol i just saw your sig, you are very prepared in helping noobs xD
WOW i have been trying to install CWM since thursday and with your method i did it within a matter of seconds! Thanks!!
Again see link in my signature for ICS install instruction. I suggest you play with a 2.2 like Fishman 's Bionix and familiarize yourself with handling functions like flashing, restoring, ram tweaks, ....otherwise you might get into more than you can handle. ICS is a pretty advanced flash and could potentially brick your device if something goes wrong. Not as easy as just flashing update.zip, hence my guide. Also see warning at the top of the guide. Very important and the cause/solution is still WIP.
Also you are on your own for finding the needed files. Sorry but my dropbox acct has been getting flexed lately so i am giving it a break. Good luck and make sure you hit Xrider's thanks for posting in two separate threads to helps you with the .apk.
Going to bed. Good luck.
Woodrube said:
Again see link in my signature for ICS install instruction. I suggest you play with a 2.2 like Fishman 's Bionix and familiarize yourself with handling functions like flashing, restoring, ram tweaks, ....otherwise you might get into more than you can handle. ICS is a pretty advanced flash and could potentially brick your device if something goes wrong. Not as easy as just flashing update.zip, hence my guide. Also see warning at the top of the guide. Very important and the cause/solution is still WIP.
Also you are on your own for finding the needed files. Sorry but my dropbox acct has been getting flexed lately so i am giving it a break. Good luck and make sure you hit Xrider's thanks for posting in two separate threads to helps you with the .apk.
Going to bed. Good luck.
Click to expand...
Click to collapse
Thanks you are a big help.
i am just a noob in this phone. i have been flashing and roting ever since the G1, i had the G1, Mytouch3g, Mytouch 4g, and i am currently using my amaze 4g, but i also have a vibrant that i want to root and put ICS on it but thanks!