Related
After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed
did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?
i had it to only closed al my apps in taskm and it stoped flickering
My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?
I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.
I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!
Buy pocketshield, problem solved.
i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.
Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.
theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me
Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos
Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...
But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.
The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1
Thank you very much. I opted for the hard reset option... I hope it stays ok this time!
My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved
i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers
so I put the dimming to be after 30 seconds, which works.
however I put it to shutdown the scree after one minutes, however it stays on forever, unless I physically press the hang up key, the screen will be on all the time.
the other question I have.
2- When I search on google, and press on one of the results in opera it takes me to the definition page, rather than the actual result that I wanted
3- is there a fix for LED notification, I installed the cab to fix that, but it didnt make a difference.
4- the pink spot at the middle, I searched around but didnt see any real solution
can anyone help please
regards
While I can't offer any help, I can feel your pain! I too am experiencing this f**ing event! I placed in my pocket before boarding for a 6 hour flight yesterday and found it still powered on when the flight had ended. I had just enough power to make and receive a call! Great.
I've double/triple checked my settings after this same thing happened to me previously! WTF!
edved.
i had the same problem what you need to do is to change the screen light setting in the settings menu
moneysaver05 said:
i had the same problem what you need to do is to change the screen light setting in the settings menu
Click to expand...
Click to collapse
Ok. I'll try your suggestion, but please tell me what the screen light setting should be?
Thanks.
just go to the backlight settings, tap ok and it seems to be fixed..
(but offcourse check if is set to turn off after a minute or whatever your needs are)
I experienced this yesterday.. just like in normal windows, some functions just stop working with no particulair reason.. I don't really worry about it.. probably fixed in the next rom.. same sometimes happens with the screen lock, sometimes it's gone.. also after reboot, althought I find it more convient that way, it can be fixed by locking the device manually.. this does proof we can disable the device lock somewhere, I really don't need it in the case I use, the power button is enough..
good tip to always push the power button before putting the device away.. saves a lot of battery too then to wait for the minute before it powers of by itself.. the large screen is the battery's biggest consumer.. this way you also don't have to trust the automatic power off.
problem is pushing the power is not enough.
because if there were any even that woke the phone up, it will never shut down the screen unless you saw it, and do it manually
mmmalas said:
problem is pushing the power is not enough.
because if there were any even that woke the phone up, it will never shut down the screen unless you saw it, and do it manually
Click to expand...
Click to collapse
no the automatic power down is seperate from the screen lock, but for some reason they connected it with the automatic power down and left the options to choose out.
I've had a problem with my E900 since I got it with regards to the screen. I was hoping Mango might fix it but it doesn't seem to have.
Sometimes if I press the power button the screen backlight comes on (i.e. screen goes from off state to powered) but there is nothing on the screen. No amount of button pressing will cause the screen to show anything.
If this happens I have to turn the device off again (backlight then goes off) and try again. Sometimes it can take 2-3 times before it turns on successfully with the lock screen.
I also have this if an incoming call attempts to wake the phone and also alarms too.
Does anyone else have this issue?
I confirm this one popping sometimes. Not that often that it becomes annoying, but nevertheless.
Did you find a solution to this problem? I am experiencing it too and it is very annoying!
I've recently inherited one as well (E900 that is).
The one I have has been dropped, the backlight powers, but no drawing on the screen.
I've disassembled and re plugged everything (bugger stripping down!) but still no luck. I've done a VolUp+Down+Cam+power hard reset, and when I plug into PC Zune says setup needs completing (so it has reformatted) but still no luck.
I cant see anything fried, and no damaged ribbons as far as I can see, any ideas?
I sold the phone a while ago, and never solved the problem. I think it's a firmware issue.
PaulMdx said:
I've had a problem with my E900 since I got it with regards to the screen. I was hoping Mango might fix it but it doesn't seem to have.
Sometimes if I press the power button the screen backlight comes on (i.e. screen goes from off state to powered) but there is nothing on the screen. No amount of button pressing will cause the screen to show anything.
If this happens I have to turn the device off again (backlight then goes off) and try again. Sometimes it can take 2-3 times before it turns on successfully with the lock screen.
I also have this if an incoming call attempts to wake the phone and also alarms too.
Does anyone else have this issue?
Click to expand...
Click to collapse
hi.
What do you mean "somethimes if I press power button"?
Is it pressed with purpose to lock the phone, press it to turn off phone (background slider shows to power off - on Mango and beyond version) or press it accidentally?
Cheers.
So, I did a phone reset. Unfortunately the issue is still present!
Sometimes when I press the power button to unlock the phone the screen is lit, but stays blank i.e. no lockscreen wallpaper, no nothing. The same happens sometimes when I get a phone call - the phone rings and vibrates, the screen is lit but stays blank.
When this happens I have to press the power button to put the phone into sleep mode and press it again to wake it up.
What I found is, when the issue occurs the screen is actually responsive. For example I can slid up and unlock the phone then I hear the unlock "pop" sound. It's just that nothing is drawn on it!
I was wondering if anyone else experienced the same behavior and found a resolution. Also I am not sure if this is a software or a hardware problem. If I could confirm it was a hardware problem I would call LG and have the phone repaired or replaced.
i have exactly the same issue as you, it gets really annoying.
i heard from someone online that the only way to resolve it is to replace the motherboard
billybrown said:
i have exactly the same issue as you, it gets really annoying.
i heard from someone online that the only way to resolve it is to replace the motherboard
Click to expand...
Click to collapse
I am pretty certain this is a hardware issue. I am calling LG tomorrow and hopefully they'll take the phone for repair/replacement.
I sent my phone for repair. Today I got it back, and guess what?!
The issue is still present! It seems, they "couldn't reproduce" or something.
What should I do now?
EDIT: If anyone is interested, here is a video I just captured which clearly demonstrates the problem. http://youtu.be/38kF9RYs_bU
I'm sending the phone back for repair tomorrow with this video attached.
Hey, might not be an issue at all, but in the video, I saw that the two times you were able to get it to go blank you had your finger on or near the proximity sensor. I wonder if there is something that could be the trigger.
Just wondering if you can duplicated it or cause it only when you have the proximity sensor blocked, or if it truely is random.
You are right, it might has something to do with the proximity/light sensor.
On the other hand, this issue occurs even on incoming calls when the phone is placed on a table, screen up and nothing around the sensor.
Today, I visited my local carrier shop and left the phone for repair again. They told me, since this is a second claim they'll run it through the process faster, so I expect to get it back next week.
Will post an update.
UPDATE: My phone was replaced. Yesterday I got a brand new unit, yeah! It was stock wp 7.0. I plugged in my sim and used the phone the whole day, no sign of blank screen issues. Last nigh I installed all the updates (total 5 I think) up to OS 7.10.8107.79, FW 1.0.16.10. Guess what?! Same issue!
I am crushed
Hi there. I'm currently having an issue with my S7 edge where the lock screen won't turn off after some time. The screen does turn off when I'm using the phone normally from the main screen after some time passes but it's just the lock screen I have issues with.
Whenever I charge my phone or just hit the power button once to see notifications on the lock screen, it'll just stay like that until the same time the main screen timeout configured time passes (5 minutes) and this is getting annoying and somewhat draining a little bit more of my battery. Previously it was working fine and the lock screen would turn off after around 10 seconds or so.
Has anyone faced any similar issues with their phones? I haven't tried a factory reset yet but I'd want that to be a last resort.
Clear Background apps.
It happens when you left some games or apps by pressing home button but it keeps running. Hope they will fix this soon.
Have you tried pressing that little button on the right side of the phone? That usually helps.
Yeah...I already tried that with no luck. Even tried uninstalling some recent apps in case one of them was cause but it didn't work either. Any other suggestions?
The issue isn't with turning the phone screen off by pressing the power button, it's the lock screen itself not turning off after a few seconds when it usually does.
I'm having the same problem, had good lock installed thought that may have been the problem but after uninstalling that I'm still having the same problem with samsungs oem lock screen. I too would like an answer or fix for this. also to note, in developer options the stay awake is off and no apps running in the background.
I am having this problem now also. The screen will lock, but the display stays on but dimmed. I can tap the screen and it will get bright. Now I must click the side button every time I set my phone down or the screen will drain the battery.
I'm facing exactly the same issue. When the screen is locked, it stays on for the same time confirmed to when its unlocked. For example, 1 minute, instead of 10-15 seconds.
Any workaround discovered for this?
Did anyone find a solution to this problem?
I thought that I might've been the only one! This problem only appeared on my phone after the Nougat update, and it's extremely annoying as I rely on notifications waking the screen for my main messaging app.
joelnet said:
I am having this problem now also. The screen will lock, but the display stays on but dimmed. I can tap the screen and it will get bright. Now I must click the side button every time I set my phone down or the screen will drain the battery.
Click to expand...
Click to collapse
Hello, I am having the same issue in my Redmi note 11 pro plus Phone. In my case The screen will lock but display stays on with dimmed light. Usually it is not visible during day, but in dark room its visible. And it stays the same way whole night. And battery is fully drained and phone is turned off. Is there a solution for this??
Hi,
i have tome hassle with the hard press home thing.
Sometimes its working ok sometimes it does weird things.
for instance ... if i press the button hard it some times vibrates , when i let go it vibrates again and its unlocked... thats when i think its working correctly.
but sometimes it just vibrates two times although i didnt let go ...
sometimes on homescreen i swipe the homebutton slightly to clean it a bit... not hard pressing and its vibrating. sometimes one single time sometimes two times in a row .
anyone with the same issue ?
thanks
no one ?
Check what sensitivity you have the button set at. It could be too high or low.
I have mine set in the middle and never have an issue.
i tried severeal sensitivity settings ... sometimes it gets better and sometimes worse... but for me its not satisfying
i think i have to weit for an update or so ...
I had the exact same issue with my S8. Sometimes it just works, sometimes it doesn't detect it, sometimes it registers several hard presses even though I've barely touched it (sensitivity reduced as far as it goes).
This has been driving me crazy for the past week. The hard press function was unusable because of this.
At first I thought it's a software issue (something to do with calibration maybe?). I got an update which didn't fix it. I tried resetting it which didn't work either so I sent it back to Samsung yesterday. Waiting to see what they have to say about it.
The lack of complaints about this so far made me think it's just a weird issue with my unit.
I'm having exactly the same problem and it's driving me nuts for not knowing if it's a hardware or a software problem.
I've googled around and this is the only thread so far. Seems like there are very few people with this issue.
Let me know how the repair request went.
i sent it back also
new one is coming tomorrow ... lets see... will report
I have that issue too. Dont know what to do.
B-Man2005 said:
i sent it back also
new one is coming tomorrow ... lets see... will report
Click to expand...
Click to collapse
Oh wow, that's really fast. I still haven't heard anything from them. Did they give any information about what's wrong (hardware/software)?
no ... i didnt sent it back to samsung.
i bought it from amazon.de and ordered a replacement.
thats faster
it will arrive today then i can sent back my first one...
same here, having issues with the home press function .
I also send it back to the shop where I bought it
I´ve send mine back to the webshop also. My mate got his s8 2 days ago and his hard press was perfect and responded smoothly all the time. So i guess it must be a hardware problem.
Will share more info when i get feedback from the repair.
Same problem here, sometimes it works, sometimes (when the device is in standby) it works only after several tries and pressure in different spots.
Can someone who has got a new device or sent it to repair report if it is better now?
Hardware issue... my replacment Works fine now
Same problem
I have this issue also. Mostly it works, but sometimes it doesn't work and the phone hesitates to come back to life. If I press the power button after hard pressing the home button or just wait 5-10 seconds, the screen will come on. Oddly, when it doesn't work (and occasionally when it does), the small vibration thing happens. I have this turned off, but sometimes when hard pressing the home button, I get the vibration, but the screen won't come on. Other times, I get the vibration and the screen will come on. Mostly I don't get the vibration and the screen comes on. Annoying.
wmupchurch said:
I have this issue also. Mostly it works, but sometimes it doesn't work and the phone hesitates to come back to life. If I press the power button after hard pressing the home button or just wait 5-10 seconds, the screen will come on. Oddly, when it doesn't work (and occasionally when it does), the small vibration thing happens. I have this turned off, but sometimes when hard pressing the home button, I get the vibration, but the screen won't come on. Other times, I get the vibration and the screen will come on. Mostly I don't get the vibration and the screen comes on. Annoying.
Click to expand...
Click to collapse
As i said ... it seems to be a Hardware issue. Get a replacement
Mine does this often, i personally could care less for the home button function so I set the sensitivity to max and yet at times if I barely touch the home button area it acts like I have hard pressed the button.
Sent from my SM-G950U using Tapatalk
I have the same problem maybe even worse. To me it looks like it is accumulating presses, the more times I press the button the more times it vibrates. So at the end I sometimes get 4 or more vibrations for just one press. Sometimes after I lock the screen it vibrates by itself and turns on the screen.
Looks like I'll get mine replaced ASAP.
Got the same issue once in a while.. also have a faint red glow on the screen. Considering getting it replaced but dont want to wait for a replacement.