ok i got a refushbished hd2 from best buy the third one and it seems to work well this tim the first one would overheat then the next wifi wouldnt work now this third one i have the Dorimax rom on there a really awesome rom but after some non use of the phone it doesnt respond the screen doesnt respond and then i take out battery restart and screen will not work and after a few hours the screen will work again and theres no over heating over anything works prefect but screen sometimes doesnt wanna work any ideas?
Try adjusting the CPU governor settings. I've had better luck on smartass, smartass2, interactivex with no more freezing, make sure your min CPU setting is at least 245mhz. Cm settings/performance/cpu
Sent from my HTC HD2 using Tapatalk
how you had this issue before?
sorry to say but well i did it i did a full wipe and a clean install and adjusted my cpu it looked like it was working and then it happened again and i dont think its a freeze issue i think its the lcd/digitalizer because it can reboot and the screen will still not work but ill vibrate the same way it reboots
Related
Aside from being able to Wirelessly Tether my 3G connection from my Vibrant, I wanted to also control my CPU speeds. But with SET CPU, I tend to come across a particular problem. I would underclock to 100000 (min&max) with the screen off, but as a result, the screen won't turn back on and I would have to take the battery off and restart my phone. Clocking it to 400000 (both min and max) screen off leads to the same problem. Is anyone else going through the same situation? If not, what are you setting your CPU to, in regards to both screen on and off?
I have it set to 400MHz max/100MHz min for screen off, and it wakes up just fine so far.
What is your Governor setting? I was told to put it in "Conservative" for Vibrant.
lqaddict said:
I have it set to 400MHz max/100MHz min for screen off, and it wakes up just fine so far.
What is your Governor setting? I was told to put it in "Conservative" for Vibrant.
Click to expand...
Click to collapse
Yeah I have all my profiles set to conservative. Do you guys think it has to do with the priorities, cause I have all of them set to 100.
It could, since there is no telling how to prioritize the settings, hardware/software might get confused.
you know I just noticed I got the same issue, sort of.
I have multiple profiles setup, and one is for charging via USB 800max/100min.
If the screen is off (400max/100min), and I connect the USB cable, guess what happens, three finger salute gets it back, hmmm.
OK I got it working for those who are having the same problem as I. All I did was I made my screen off frequency 200max/100min. For both charging and battery use, I have my cpu set at 1000max/800 min. It works flawlessly and I am noticing an increaSe in battery life...
Sent from my SGH-T959 using XDA App
OverClock?
I used SET CPU on my G1 and really loved the new life it gave my old hardware. I would like to open it up and see what my Sammy Vibe can really do. Is there a way to get some real OVER clocking?
Battery life is really not an issue for me so far.
Halieus said:
I used SET CPU on my G1 and really loved the new life it gave my old hardware. I would like to open it up and see what my Sammy Vibe can really do. Is there a way to get some real OVER clocking?
Battery life is really not an issue for me so far.
Click to expand...
Click to collapse
we need a kernel that will enable it. its apparently not possible on the stock kernel...
I have been having the exact same freezing issue when the screen times out, I'm unable to revive the phone without pulling the battery. I have tried many different setting in Setcpu including those posted here. I finally just uninstalled it and everythings right again. Best to avoid this app for now.
Hey man i did that and i still did not work any other way to set it up.
Vibrant wont come out of Blank Screen
I used Set CPU and put it to the max 1000 and then the max on the other readings it forced closed and after the tmobile and Galaxy animations it goes to a blank screen.
Yeah, I uninstalled it after a week because it was just too unstable. I was getting freezes several times a day, which is unacceptable. Other people might have better luck, but my phone did not like it at all.
So far the only way I can get the program to work 100% is to not have any screen off profile. If I just set it to 1200 max - 200 min / conservative it works fine. Yet once I use profiles and screen off at 100, 200 or 400 it won't turn back on. Every morning it's the same thing, battery pull.
I have similar problem. As long as I am not using "Profiles" at all it is fine. Playing with profiles setting for a while, but not being able to make them 100% stable.
Another thing, if your screen does not come on, you don't have to pull the battery out. Just keep holding on/off button for 5-7 seconds, it'll reboot. It's not a complete freeze, I believe only display system (whatever it is) fails.
Stuck at Recovery Mode
Guyz,
I have firetrap sugar on Spice Mi300. Installed Set CPU.
Tried entering the recovery mode, the phone gets stuck at 1st screen with a line "Enter recovery Mode" displayed on top.
Please help.
Hi,
I have this annoying problem regarding waking up my device when its locked. Normally i should press the power button, or the trackpad as im running virtuous rom, and the screen should give me the lock screen. But this does not happen, intead screen stays black, the keys on the bottom do light up, and it registers my touches on the screen as i can put the music player on again.
This is happening for quite some time, but lately its more often and its really frustrating me because i have to hit the power button for like 10 times in a row before it finally goes on again.
When it stays black and i put it off again, touching the power button, moste of the times the screen will flash the lockscreen and go black again.
Ive tried to find a sort of system in it, like a period of time or somthing like that, but it seems as if its completely arbirtrary when it happens and when it doesnt.. Only thing i remarked was that when it's off for a longer time, it will have more chance of getting on the first time then when its off for a shorter period...
Any suggestions to fix this evil thing?
cheers
This is a very comman problem.
what you need to do is setting up a screen off profile on setCPU
min 245
max 368
scalling : powersave
I agree check your screen off profiles. Also try not to oc too high. You might also want to install the pershoot kernel if you haven't already. I had this issue when I fist installed the virtuous rom & switching kernels and tweaking my cpu profiles resolved this issue.
Sent from my HTC Vision using XDA App
Screen off profile doesnt help, What does work is less oc'ing it... stupid thing is i can only oc to 902 mhz for the screen to turn on all the time... Thats like not oc'ing it at all ><... I'm on the virtuous kernel now, will try the pershoots in a min, i'll keep you updated
Oh sorry, screen off profile does help, didnt enable profiles in a whole ... pershoot kernel helps a lot, with that one and the screen off profiles, i can oc to 1517 and even then its just not going on very rarely... thanks for the help... Only thing thats regrettable is that the pershoot kernel does not have the smartass governor ...
EDIT: I realised i didnt enable the profiles while using the virtuous kernel either, so i installed that one again and guess what, it works!! Every single time i hit that power switch it goes on like it should... what a relieve thx guys
grtz
Hi, I've just flashed leedroid but I seem to be suffering with some small amount of lag that I didn't experience on the stock Rom..... when I open messages or emails for example there is a small pause, and u can visibly see the screen refresh. I never suffered with this this beforehand. Also I have noticed that I'm getting some lag when changing certain settings, the leedeoid Icon pops up whilst its thinking..... now, so far I haven't gotten around to installing the LeeDrOiD Ace V2.2.5 R2 Kernel, is that likely to fix my little issue?
Cheers
Steve
After flashing, have you done another reboot? Sometimes I find a new ROM doesn't settle until I've rebooted a couple of times. Give it a try and see how it feels then report back either way
Let it bed in steve, should have dropped this in the rom thread
LeeDroid said:
Let it bed in steve, should have dropped this in the rom thread
Click to expand...
Click to collapse
New members aren't allowed to post in Dev section until they hit a certain post count
Yup...reboot will fix your problem..
Sent from my Desire HD using XDA App
Thanks for the reply Lee, but as citizenlee said, I'm unable to post in that section at present.
So far i still seem to be having the slow refresh issue on sms and emails, do u think that the fact I haven't flashed the Ace V2.2.5 R2 Kernel yet could be part of the issue? I'm certainly going to try flashing it to see if it helps..... I know know you've put a heck of a lot of work into this and believe me it is appreciated, just hope I can get it working as well as it was intended.
You could try the kernel... and failing that a full wipe and reflash of the ROM should sort you out
problem
LeeDroid said:
Let it bed in steve, should have dropped this in the rom thread
Click to expand...
Click to collapse
dear lee i have installed your PERFECT rom 2.2 1.8 ghz
but it has frozen 2 times the screen and after rebooting it stays frozen...?
this also happened with coredroid ..any suggestions my friend?
regards(i am new here^^)
Ok, i think i got to the bottom of my lag problems. I have been playing around with set cpu today. I think the minimum speed of 245mhz in smartass was too low and was causing the lag (usually when waking the phone from screen off) I have now changed settings to 'ondemand' with a minimum speed of 245mhz and maximum of 1344mhz but i also created a 'screen off' profile with a working range of 245mhz to 576mhz which seems to give it a bit more poke when waking from screen off No more lag! ( i still have the visible refresh issue i mentioned, maybe i'm imagining that one though, maybe it did do it on the stock rom but i didn't take note of it....??)
So, i really have no idea if i've done the right thing with the way i have set up setcpu so if anyone would care to comment on the settings i've used please do so.
Many thanks again for all the help.
Steve
I have a T-Mobile G2 that's been rooted and flashed several times (cm6, virtuous, supervillainz, senseginger, cm7) and through I think all of them I noticed an issue with coming out of sleep where the screen doesn't turn on
it still reacts to touch (ie I can slide to unlock), and the bototm touch keys light up, but there's no backlight or picture on the actual screen
sometimes it takes several off-on cycles to get it to work... I've recently noticed (and may be just imagining it) that the trackpad wakes it up with a much better success rate
details:
HTC Vision (G2)
Android 2.3.3
Baseband 12.28b.60.140eU_26.03.02.26_M
Kernel 2.6.32.28-cyanogenmod-g58d929e [email protected] #1
CyanogenMod-7.0.0-RC2-vision
any ideas would be welcome before I lose it and start poking at the kernel, radio and whatnot
thanks,
L
happens to me in virtuous, never happened to me on CM (i havent tried cm7 yet)
i believe its a problem with the cpu scaling, ie when the screen is off, processor drops to 245mhz and when the screen turns on, speed doesnt scale up fast enough
i usually underclock my g2 to 599mhz (governer set to on demand) but if i go any lower than that, getting the screen to come on becomes a frustrating project lol
I have the same problem, its so annoying especially when someone calls. Its been mentioned in other threads and I'm sure its a known problem but like u I need a fix. Stock ain't so bad as long as u can see who's calling and what time it is without trying to wake the phone 20 times. Please will someone finally answer this question? Or do we all need to revert to cm 6.1 or stock????? Small problem but big outcry.
Sent from my HTC Vision using XDA Premium App
thanks, I downclock to 200mhz on screen off
I'll up it and see if it makes a difference
Are you using the screen off animations in CM7?
Sent from my HTC Glacier using XDA App
screen off yes, screen on no
Try disabling the animations all together and see if it helps. Also are you OC'd above around 1.2ghz?
Sent from my HTC Glacier using XDA App
I've disabled them for now, gonna see if it helps...
yeah OC to 1516MHz, do you think this affects it?
There was a known issue with CM7 not too long ago where if you had the screen off/on animations activated in conjunction with being OC'd at around 1.2 or above it would cause the sleep wake issues. Took 3 or 4 on/off cycles with the sleep button on order to get the screen to come back on.
The solution was either to disable the screen animations or not to OC very high.
The other remedy recommended earlier is also legit. Set your screen off CPU profile to around 300 or 400mhz. Your problem should be solved by tinkering with all 3 variables. Failing that I would recommend a wipe/reflash and/or hitting up some folks in the CM7 thread to see if anyone else has that issue after tinkering with the above solutions.
Good luck man, I know those little bugs can be frustrating.
Sent from my HTC Glacier using XDA App
thanks for the tips...
I've now upped the minimum clock to 400 across all profiles and turned off the screen off animation... if that doesn't do it, I'll turn down the maximum clock, and if that still fails disable setcpu completely
I will report back any findings
allixsenos said:
thanks for the tips...
I've now upped the minimum clock to 400 across all profiles and turned off the screen off animation... if that doesn't do it, I'll turn down the maximum clock, and if that still fails disable setcpu completely
I will report back any findings
Click to expand...
Click to collapse
I see you have a strange problem.
I use 275mhz when sccreen is off and about 476 mhz when screen is on and nothing like this has happened to me.
Sent from Mars
Seems like nature of the beast. I get it too. Are yall using setcpu? I think its an issue with it. U might try cputuner and see what happens. But it rarely happens now that i set my setcpu to conservative or smartass.
Sent from my HTC Vision using XDA Premium App
this is indeed an issue with downclocking the phone on screen off profile... as soon as I set the screen off profile to anything below the stock 806 mhz, the issue appears
I've reenabled both screen off and on animations, the issue still hasn't reappeared... so it's the downclock :/
I have seen it on Sense ROMs but not CM7, doesn't clocking your phone at 800 when display off eat up a lot of battery also?
I am, unfortunately, not that techno-savvy when it comes to cellphones. But I am having the same problem.
The most I get is a bit of back light, but everything else about the phone seems to be working. Is there anyone who could possibly help me figure out how the hell to fix this?
SO this is weird what im about to tell u is trick and a BUG so how is that possible here is how ::
When i open a game on my hd2 especially a hard on the graphics one like lets say { into the dead or beach buggy ]
u see when ever i start these gaames they freeze so how do i make them start and unfreeze the system .
JUST PUSH THE POWER BUTTON FOR SEC just like ur turrning the screen off not force shutdown the device or any thing
and click it again it will open the lock screen so open that and u will find the game working and actually very playable .
Its weird and the only workaround for it is by installing chainfire 3d but the problem is that most roms aren't compatible with it and if u install it on any ROM and reboot it may not boot again unless u reflash that ROM ...
So devs any easy fixes for this bug ""?>:":?>
Interesting solution, thanks for the info. One thing I have to point out though is that people will have to be careful doing this if they underclock their CPU when the screen is off as they may need to battery pull and restart. I tried listening to music with a 128MHz underclock on my HD2 once and the screen just wouldn't turn back on.
Does underclocking increase battery uptime? Cause as far as I know, the Voltage on 460-128MHz does not differ (atleast as for my kernel (example)). Therefore it won't change the draining of the batter - am I right?
If there is any difference, its very miniscule. I think leaving the CPU profiles as they are is probably the best solution.
Sent from my Nexus 4