Database Users

[Q solved] cannot mount sdcard in recovery

So this was solved by using a tool from sdcard.org to format my sdcard in a PC. Once formatted with that tool cwm started seeing correctly.
-------
I'm running 3.1 rooted
I've flashed Thor's 1.4.2 recovery.
I have two sd cards: a 2g and an 8g.
Both work when accessed on a PC and on the iconia.
Neither work in cwm so I can't flash any roms.
I have tried formatting the sdcards on two different PCs. for the 2g I tried both fat and fat32. The 8g is fat32. In every case cwm says it can't mount it.
Additionally, I can't seem to use a USB key, although that may be that i don't know how to use it.
Thanks for any help.
-Bert

When in CWM and you go to install zip from sdcard do you see any folders where you choose the zip. Just wondering if it isn't mounted already. Physical sdcard is in /mnt/external_sd
and not /mnt/sdcard.

PsychosisNC said:
When in CWM and you go to install zip from sdcard do you see any folders where you choose the zip. Just wondering if it isn't mounted already. Physical sdcard is in /mnt/external_sd
and not /mnt/sdcard.
Click to expand...
Click to collapse
Thanks for your reply. I'm prety sure It's not mounted already.
I'm attaching a screenshot to show the exact message I get when trying to browse for a zip. I get a similar message when I go to mounts and storage and try to mount the sdcard.

im bumping this because I'm really becoming concerned that the device is defective in some way.
I'm hoping that someone can give me some guidence on what I may be doing wrong.

So, brosell, did you figure out a solution? I have the exact same problem - cannot mount sdcard in recovery and I get the exact same message.
When the system is booted normally, the internal storage mounts ok as /sdcard
EDIT:
It seems CWM treats the external sdcard as /sdcard, not the internal storage. So, to flash an update, you need to place it on an external SD card

I always get that error, and I never had to mount anything using cwm, just booted it selected the zip to flash and flash. I still don't mount anything...?
And the zip goes on the external sd not the inturn

Can't format SC Card in Window. If won't mount.
Guys,
Unfortunately SD cards for Android must be formatted by Android. If the card is not properly formatted CWM can not mount it, nor can CWM format it. The best way to get it properly formatted is to put it into an Android Phone and use its format functions. There really is no way on the Icona Tab to reformat an improperly formatted card or a new formatted card. If you don't have an Android phone borrow a friends. You will know that it is properly formatted when you see a lost files folder created on the card by the Android phone formatting process. This is a common problem that many people encounter when performing their first ROM flash. If it was formatted under windows as FAT 32 you can access it and store on it in normal operation mode. But ClockWorkMod can not mount it in recovery mode. Hope this helps. Good luck.

Can mount SD card in Recovery
I should have also mentioned last night in my post here, that my experience has been that it is much easier to flash a new custom ROM from a USB thumb drive. Flashing a custom ROM from USB seems to be less problematic than from an SDCard that appears otherwise to be good and formatted with FAT32, but CWM can't mount it. You can fast format the thumb drive on Windows to clean it off. Then copy your custom .zip ROM to be flashed on to the thumb drive from within Windows then insert it into the USB port of your Icona Tab, boot into CWM recovery (I'm assuming you know how to do that so I won't go into it here.) I forget exactly where in the CWM menu it is, it might be under the CWM advanced sub-menu but it say's something to the effect of Install zip from USB. It always works for me with no problem. The advantage is that you do all your prep work on Windows and then flash from the thumb drive which I believe has an ISO standard across all platforms and usually comes already per-formatted. This is an alternative method if you can't get your SDCard properly formatted (see my previous post in this thread for how to get it properly formatted so that it will mount under CWM.) Again, good luck!

I want to cry!!
I tried re formatting! Nothing! Cmw is not on sd card! Nothing is working! Still stuck on acer start screen! Yes i am a noob! But i read alot into this stuff b4 i do it! I wish there was someone i can have come to my house and do this for me! I have tried everything!!!!!!!!!!! So frustrated!!! Someone pls help me!!!!

in CWM recovery, there are 2 options,sd and "internal sd" i think(for me atleast). i chose the internal sd and it mounts.

brosell said:
So this was solved by using a tool from sdcard.org to format my sdcard in a PC. Once formatted with that tool cwm started seeing correctly.
-------
-Bert
Click to expand...
Click to collapse
Thank You Sir! been looking for this fix for a long time

brosell said:
So this was solved by using a tool from sdcard.org to format my sdcard in a PC. Once formatted with that tool cwm started seeing correctly.
-------
/QUOTE]
thanks brosell, for the solution,
I have a 512MB SD card in the g5360, was FAT formatted. reformatting the sdcard with the tool from sdcard.org worked for me as well, afterwards it could be mounted by the stock recovery
and could install update.zip (prior to install CMW)
kr, Erik
Click to expand...
Click to collapse

[Gparted] Nook Simple Touch resize partitions non-destructive

!! Important: Make a backup of your Nook device first !!
Resize partitions
1. Download Gparted LiveCD
2. Extract onto FAT / FAT32 USB memory stick or burn to CD-ROM
3. If on a USB memory stick, run \utils\win32\makeboot.bat from the memory stick.
Do NOT run makeboot from a hard disk!
4. Boot computer from USB device into Gparted
5. Connect your Nook running Noogie of a Micro USB card (this will make the partitions visible to Gparted).
6. Resize the last partition (nr 8) labelled "data" (= Barnes & Nobles content)
Make sure to move the partition to the far right.
7. Move the next-to-last partition (nr 7) labelled "cache" without resizing it.
8. Extend the next-to-next-to-last partition (nr 6) labelled "nook" (Side loaded content) to fill the gap.
9. Remove USB cord, Micro USB card and boot your Nook.
10. In Settings you can inspect the amount of storage space.
I received errors when the partitions were about to be moved on the disk.
I changed the partitioning resize to field where it says "Align to:" from "MiB" to "Cylinder". After a 2nd attempt and doing each partition individually all worked out well.

For those only with Windows, download Gparted LiveCD iso image and use virtualbox to boot from it. It still worked well.
Edit: I successfully repartitioned two of my Nook Simple Touch using the method above + virtualbox + Gparted LiveCD iso.
Surprisingly, the size of partitions in my two NST were slightly different, suggesting that the physical size and location of partitions don't matter as long as their order and type in the partition table are as expected and the size is big enough to hold files there. I resized and moved the last three partitions as I wanted several times and made sure they work well.
Factory reset, upgrade to 1.2.1 (this seems to require the cache partition to be big enough to hold the firmware update file: something like 128MB worked for me), rooting all worked well with resized partitions. I ended up shrinking the cache partition down to 32MB and the data partition to 128MB, reserving 1.11GB for the side-loaded contents. I'm sure the system partition can also be shrunken, but I didn't go that far.

Why a live cd? Does installing gparted to whatever linux flavor you're using not work?

I don't use linux on my PC... only on hacked router & nas.
Goggles2114 said:
Why a live cd? Does installing gparted to whatever linux flavor you're using not work?
Click to expand...
Click to collapse

So dump Noogie on a microsd card run noogie and while noogie's running plug nook into pc? Do you just plutg it in and it does everything auto, or does something in noogie need to be run? Does this work on a nook touch glow?
Sorry to sound so dense but rooted using NookManager.
Edit more to the point it's throwing up an error when trying to move sdb8 around. It shrank fine just won't move. Not sure why. Not getting any useful error messages. Just 'can't have overlapping partitions.'
Odd. I was able to move it twice and get it to behave. Yet do the same n one move and Nothing. Apologies for the rinning Log just. Meh. The rest of the partitions resized in one step. sdb8 was the one that needed two steps.
Aaaand Success. Showing up as having 913MB free as opposed to like 212 or whatever.
Edit: now I'm getting a constant 'low space' warning from nook (understandable.) And installing apps is hit/miss on if they'll actually install. Keeps claiming space issues.
Query. Do apps install to the BnN partition or where?

Good to hear another success story. In my case I squeezed all the way to 1.45GB for the side-loaded contents. boot/rom/system/cache/data partitions are shrunken, and factory partition is busted. I had to use fdisk instead of GPartED to completely recreate the partition table, though.
I think, apps are installed to the data partition (the 8th one) under /data/app. Before being installed it's downloaded to cache partition (the 7th one). In my case I gave 16M for cache and 128M for data. If you are low on the data partition and have some space left on the system partition, you can move apps from /data/app to /system/app.
Goggles2114 said:
So dump Noogie on a microsd card run noogie and while noogie's running plug nook into pc? Do you just plutg it in and it does everything auto, or does something in noogie need to be run? Does this work on a nook touch glow?
Sorry to sound so dense but rooted using NookManager.
Edit more to the point it's throwing up an error when trying to move sdb8 around. It shrank fine just won't move. Not sure why. Not getting any useful error messages. Just 'can't have overlapping partitions.'
Odd. I was able to move it twice and get it to behave. Yet do the same n one move and Nothing. Apologies for the rinning Log just. Meh. The rest of the partitions resized in one step. sdb8 was the one that needed two steps.
Aaaand Success. Showing up as having 913MB free as opposed to like 212 or whatever.
Edit: now I'm getting a constant 'low space' warning from nook (understandable.) And installing apps is hit/miss on if they'll actually install. Keeps claiming space issues.
Query. Do apps install to the BnN partition or where?
Click to expand...
Click to collapse

What's the point of doing all this?
You gave a list of instructions, but not the goal they achieve.

L_R_N said:
What's the point of doing all this?
You gave a list of instructions, but not the goal they achieve.
Click to expand...
Click to collapse
Which post are you referring to?

Troute said:
Which post are you referring to?
Click to expand...
Click to collapse
.c0.'s original post.

His instructions describe how to use gparted to resize the partitions on the NST to make full use of the memory available after you have rooted it. I've used gparted before so maybe they were clearer to me than to others but the thread title was the main clue.

Troute said:
His instructions describe how to use gparted to resize the partitions on the NST to make full use of the memory available after you have rooted it. I've used gparted before so maybe they were clearer to me than to others but the thread title was the main clue.
Click to expand...
Click to collapse
I kind of thought that Nook's internal 2GB flash is already sanely formatted (i.e. most space is dedicated to the partition that is mounted at /media). If that is not the case, then that should be noted in the first post. It would also be cool if it said exactly how much space each partition has (I think i saw these partitions back when i've used Noogie to make initial backup of my device, but i don't remember the details), and how much space you would gain, and on which partition (and where it is mounted).

L_R_N said:
I kind of thought that Nook's internal 2GB flash is already sanely formatted (i.e. most space is dedicated to the partition that is mounted at /media). If that is not the case, then that should be noted in the first post. It would also be cool if it said exactly how much space each partition has (I think i saw these partitions back when i've used Noogie to make initial backup of my device, but i don't remember the details), and how much space you would gain, and on which partition (and where it is mounted).
Click to expand...
Click to collapse
Thanks! i did the work 880MB for side loaded content now!!!
on one of my NST i had an issue resizing the FAT32 partition and i had to format it to make it work.
Other than that all went ok!
Thanks

How to maximize RAM available for apps
I found this easy to read table here.
I doubt that I will ever download books from B&N. I want to minimize the space for that. I infer that I should minimize partition 8 that gets mounted to \data. Is there a practical / actual minimum for this?
I see that anything I copy in from my PC over USB is going into media. 100MB should be more than I need. I could put in an SD card for this sort of thing if it grows.
My question is, which partition do I want to increase to make the maximum available to apps downloaded from the google marketplace?
If an application requires a minimum of 512 MB of RAM, which partition(s) do I need to set >= 512?
New additional question: Upon some further research, I see that you can use sd cards for swapfiles to increase system RAM up to a maximum of 4GB. Does anyone know if it is possible to use this built-in storage for the same purpose?
.c0. said:
!! Important: Make a backup of your Nook device first !!
Resize partitions
1. Download Gparted LiveCD
2. Extract onto FAT / FAT32 USB memory stick or burn to CD-ROM
3. If on a USB memory stick, run \utils\win32\makeboot.bat from the memory stick.
Do NOT run makeboot from a hard disk!
4. Boot computer from USB device into Gparted
5. Connect your Nook running Noogie of a Micro USB card (this will make the partitions visible to Gparted).
6. Resize the last partition (nr 8) labelled "data" (= Barnes & Nobles content)
Make sure to move the partition to the far right.
7. Move the next-to-last partition (nr 7) labelled "cache" without resizing it.
8. Extend the next-to-next-to-last partition (nr 6) labelled "nook" (Side loaded content) to fill the gap.
9. Remove USB cord, Micro USB card and boot your Nook.
10. In Settings you can inspect the amount of storage space.
I received errors when the partitions were about to be moved on the disk.
I changed the partitioning resize to field where it says "Align to:" from "MiB" to "Cylinder". After a 2nd attempt and doing each partition individually all worked out well.
Click to expand...
Click to collapse

I have a little (maybe big?) problem. Can't partition with Gparted Live, as gparted scans my /dev/sdb (nook) infinitely. If I plug out my nook, other partitions (in my case: /dev/sda) become visible and ready. Looks like my nook hangs gparted. Tried on 2 different PCs and no effect. Tried different version of Gparted Live (i486 & amd64) - still nothing.
Of course noogie is inside the nook unit, ready and steady. Already made a backup of (non-rooted) device, plus partitions are visible in Minitool Partition Wizard on Windows 7.
What to do in this situation? Is Linux the only safe way to repartition device? Or maybe Minitool would be as effective and safe?
If Linux is the only way to go, how to make nook visible to Gparted?
Please, experts.

DJ Athlon said:
I have a little (maybe big?) problem. Can't partition with Gparted Live, as gparted scans my /dev/sdb (nook) infinitely. If I plug out my nook, other partitions (in my case: /dev/sda) become visible and ready. Looks like my nook hangs gparted. Tried on 2 different PCs and no effect. Tried different version of Gparted Live (i486 & amd64) - still nothing.
Of course noogie is inside the nook unit, ready and steady. Already made a backup of (non-rooted) device, plus partitions are visible in Minitool Partition Wizard on Windows 7.
What to do in this situation? Is Linux the only safe way to repartition device? Or maybe Minitool would be as effective and safe?
If Linux is the only way to go, how to make nook visible to Gparted?
Please, experts.
Click to expand...
Click to collapse
If Gparted doesn't work for you, I'd highly recommend Minitool Partiton Wizard - it's what I used to partiton my Nook. Nice, easy UI, too.

Yeah, I often work with Minitool, but is it as safe as Gparted when it comes to nook?

DJ Athlon said:
Yeah, I often work with Minitool, but is it as safe as Gparted when it comes to nook?
Click to expand...
Click to collapse
Yeah, it is. Just make sure to make a Noogie backup before repartitoning.

Sorry for bugging you, but can't shrink userdata(ext3). What to do? Delete that partition and re-create it or...?

DJ Athlon said:
Sorry for bugging you, but can't shrink userdata(ext3). What to do? Delete that partition and re-create it or...?
Click to expand...
Click to collapse
Yes, delete and recreate is the way to go.

Please, people, help me
Write step to step guide for work with Minitool Partiton Wizard
I want to free the reserved space for B&N books of my NST ver. 1.2.1
The device is already rooted.
I installed Minitool Partiton Wizard on my PC, but after connecting it thru USB cable with my Nook, it only see "official" 240MBs.
Cannot find other around 750 MB reserved storage for B&N books ?
What to do
Explain to me, please

[Q] Unable to sideload to sd card...help please?

Hi,
First off if this is answered I am sorry.
I did a lot of searching and was unable to see the answer to this...
I am running CM7.1 off uSD. Install went well, and have no issues. That being said, I am unable to find out where on the card to sideload books. I have booted into CM7.1, turned on USB storage, and have 2 drives appear in win: MYNOOK and CM7 SDCARD. I used the size agnostic image, and it appears that there is only the single partition on the card, and in file explorer, it shows the correct card size for memory, but only the single partition.
The only folders appearing on the card are:
.android_secure
Android
LOST.DIR
I tried to manually copy the books, media, etc. folders into a My Files folder on this drive, without success.
There is no other partition to repartition (shouldn't have to do that with size agnostic?). I have no problem loading books into the MYNOOK book folder, which I assume is the internal device memory.
Here is my question. How/where do I sideload books to use the storage on the uSD card? Do I have to create the folders somewhere? If so where?
My goal is to utilize the storage available on the card, but be able to read the titles in the stock software. Is it possible to do this without rooting, or do I need to root for any reason to access the right folders on the card for storage?
THANK YOU ALL!!

klewlessnoob said:
I tried to manually copy the books, media, etc. folders into a My Files folder on this drive, without success.
Click to expand...
Click to collapse
In what way was it not successful? Did the files copy and just can't find them with a reader? If so which reader?

The book I transferred over was not found in the stock software when I opened my library. Is there somewhere specific I am supposed to place it on the card for the Nook to see it? Thanks!

For the stock reader, I think you must use the 1gb area of the internal memory drive, which shows up as a separate drive on your PC when you plug it into the computer. When you are in CM7 and connect to the pc, cancel when it tries to install a device for the NC. Check the notifications on the NC, you need to click a button to enable copying files from your pc, and take care to properly safely remove/eject before disabling that and disconnecting the cable from your pc. Better to get a separate reader and install it from the market (e.g., Cool Reader). You can also install the Nook app from the market, but then books need to go within (possibly in a specific subdir) of the "Nook" folder on SDCARD.

So there is no way to use the card memory to store books if I want to use the stock reader??
Should there have been a "NOOK" folder created on the SD card as part of the CM7 process? Is that a file that the user needs to create? If so, does it go in the same partition as the CM7, as that is the only partition my machine is able to see?
thanks again

Hopefully you'll get more input on this, but I think the point of keeping the Nook stock available (aside from not voiding your warranty) relates to use of B&N books. However you can eject your CM sd card and use another sd card if you want more space for user media for use with the stock app. I thought the media drive was the 1gb area, but now I'm not so sure because on mine the MYNOOK disk is much smaller.

When you are in the stock firmware... you are seeing the boot partition of the uSD...
You can write the boot partition... resize it... then run the installer...
I have done it in the past... set up a 2GB boot partition... then setup the ROM on uSD. You then have a 2GB partition you can use when in stock.

Thanks for the info. I am a bit confused by your suggestion, can you please offer a bit more?
By writing the boot partition, then resizing it, does that mean I can resize now, after I have already set everything up? If so, what do you mean by the installer? Or do you mean I have to wipe the card and start over? If that is the case (start over) do you mean wipe the card, create a small partition for the boot to install on? Would that requre the use of an image that is not size agnostic?
Either way, how do I get the file structure in place on the non boot partition for the nook to see files that are saved there?
Thanks again for any help you can provide!

I have never had luck resizing it after it has been booted in the Nook and all the partitions created...
I have written the size agnostic image to the card... resized the only partition created at that point... then put the ROM on it and booted it in the nook so the installer script (size agnostic recovery) can do the partitioning and install the ROM.
For the question of getting the file structure... I'd have to ask how you wrote the files on the uSD... were you CM or stock?

I had always planned on running cm from the card, so when I wrote the files to the card, I was stock.
If I follow what you are saying, then steps for me to try at this point would be:
1. Reformat card
2. Write the disk image to the card
3. Shrink the single partition on the card (where the image is)
4. Add the CM ROM to same partition as the image
5. Install card and boot device
If this sounds right, I have 2 questions.
What size should the partition be for the image and CM ROM, maybe 2GB?
Will the Nook "see" the non-CM partition and create the file structure for saving files on the 2nd partition at some point? In my searches I saw that in early versions, there was a requirement that the 4th partition on the card be expanded to use for storage, won't I only have 2 at this point?
Thanks again so much for the help!

When you write the image to the card... it will only be about 114 MB.... you will probably want to increase the size to avoid any possible size issues later (with ROM's getting larger)
If you plan to use the stock nook ROM as well as CM7... you will probably want 2 GB boot partition... otherwise if you plan to only run CM7 you probably only want about 250 MB.
You can modify vold.fstab on the stock ROM to use partition 4 of the SD for its SD use... then you could avoid the 2 GB boot partition.
What happens when you use VG's SASD... the boot image is about 114 MB... when you boot it in the nook it creates partitions 2, 3 and 4... 2 and 3 are ext3 partitions, partition 4 is fat... partition 4 is the one set for sdcard in the ROM booted from SD...
This is why you can modify stock vold.fstab to point to partition 4... then both ROM's will be putting stuff on the same partition for "SD Card"

I think I follow that, but my issue is that currently I am unable to see partition 2,3 or 4 which I think is part of my problem.
When I set up the card, I used the SASD method, and all I can see in both win explorer and partition software is the single partition on the card. Should there also be partitions 2,3, and 4? Do I have to do something to make those partitions viewable?
I am not comfortable enough with my skill level to attempt to modify the stock vold.fstab file on the device, and was hopeful that by properly setting up the card, I would be able to keep stock as is, and use the card to multipurpose, ie run cm7 on part and use the remaining space on card to store books to be read in stock firmware. I am still hoping to do that....thanks

As far as only seeing partition 1.... that is a limitation of Windows.
By following the advice pertaining to starting over and increasing the size of the Boot partition immediately after writing the image... before doing anything else... you can provide more space for the stock ROM to use on the SD... it will use partiton 1 (the boot partition) without the other modifications to vold.fstab

ok, confused again
If I start over, write image, then resize that partition with the image, am I going to use the "rest" of the card, NOT in that partition to use with storage? OR am I going to resize the partition with the image to be big enough to use as the partition to put books on?
If it is the former, don't I again run into the problem of how to find the other partitions, or will I create them when resize the first partition after writing the image?
Thank you!

You will only ever see the first partition of the sd card when booting from the stock OS. Also with the card inserted in a usb flash card reader on Windows you can only mount the first partition as a drive letter. But you can see and resize partitions with contiguous unallocated space using MiniTools Partition Wizard.

OK thats good to know. Do you know if the SASD install should have created other partitions when I installed to the card? The reason I ask is that even in Partition Wizard, I am still only able to see the 1 large partition with everything in it.
If I start over again, will I need to use the wizard to create partitions first, then write the image to the resized 2 GB first partition, or should I write image to card, resize the first partition? If the latter, will resizing the first partition autmatically force the other partitions to be seen? I am not sure of this option, as I can't see where in the process the other partitions are created? Is this part of the process when CM7 boots?
Thanks!

Write the image. Safely remove from pc. Reinsert to pc. Use minitool partition to resize the (only, at that point) partition to the size you want. Use Apply in minitool software. Quit minitool and resume with the card setup.

does the minitool at that point (resizing) create the other partitions, or will the card setup do that? Do I have to do anything else to the other partitions to make them visable to the stock nook so that they can be used to access books while in stock os?

The card setup will create the other partitions. The stock os is never going to see anything but the 1st partition. You would need a terminal emulator or rooted file explorer installed in the stock os in order to mount another partition.

If that is the case, that stock os will never see anything other than the 1st partition, then there really is no way to accomplish what I am trying to do, correct?
In other words, put CM7 on the card, then when I want to use stock, boot into stock and have the reader find books saved on the card?

[Q] Can I have partitions that can be accessed from both NC Stock and CM7 on SD card?

Hi everyone!
I just got CM7 (latest stable release) installed on on external sdhc card. I have wifi issues with CM7 (and looking around the forums tells me that CM7 can be finicky with certain routers) so I would love to be able to use Nook's stock ROM (4.1.4) when I am having issues.
But, when I am on NC ROM, I don't see anything except the small boot partition on the SD and when I am on CM7, I don't get access to this boot partition. I am wondering if there is a way to either create another partition or make the currently existing partitions accessible on both ROMS so that I can share data between them.
I am a n00b without any Android experience so thanks in advance for your patient responses.

Please use the Q&A Forum for questions &
Read the Forum Rules Ref Posting
Thanks ✟
Moving to Q&A

andrandom said:
Hi everyone!
I just got CM7 (latest stable release) installed on on external sdhc card. I have wifi issues with CM7 (and looking around the forums tells me that CM7 can be finicky with certain routers) so I would love to be able to use Nook's stock ROM (4.1.4) when I am having issues.
But, when I am on NC ROM, I don't see anything except the small boot partition on the SD and when I am on CM7, I don't get access to this boot partition. I am wondering if there is a way to either create another partition or make the currently existing partitions accessible on both ROMS so that I can share data between them.
I am a n00b without any Android experience so thanks in advance for your patient responses.
Click to expand...
Click to collapse
Look in my signature for a link to my tips thread. I explain there how to make the SD media partition available to both ROMs (item B3).

leapinlar said:
Look in my signature for a link to my tips thread. I explain there how to make the SD media partition available to both ROMs (item B3).
Click to expand...
Click to collapse
*That's* the one I wanted to point them to.

leapinlar said:
Look in my signature for a link to my tips thread. I explain there how to make the SD media partition available to both ROMs (item B3).
Click to expand...
Click to collapse
Thanks.
Do you mean step #3 in Section B? I could edit it without running your script too, can't I?

andrandom said:
Thanks.
Do you mean step #3 in Section B? I could edit it without running your script too, can't I?
Click to expand...
Click to collapse
If whatever you have on emmc is rooted, you can manually edit it. If you have unrooted stock, then you need to flash the zip since without root you cannot edit those files manually. And I did mean item B3. Each item is a different topic, they are not steps. One topic does not depend on another. Just do B3 and no others if you want.

Yes, item B3. My mistake...
I should be able to do flash the zip from my current CM7 SD card's boot partition, shouldn't I?
So I put the update-stockemmc-vold-fstab-modified-for-partition4.zip file in the boot partition of the SD card, rebooted to Recovery mode and then booted to NC's stock ROM. NC is still using the tiny boot partition on the SD card as my external storage instead of the much larger CM7 partition. This was the same partition that was under 'My Files / Memory card' before I flashed so nothing has changed. I did this twice to double-check.
Am I doing this wrong?

andrandom said:
Yes, item B3. My mistake...
I should be able to do flash the zip from my current CM7 SD card's boot partition, shouldn't I?
So I put the update-stockemmc-vold-fstab-modified-for-partition4.zip file in the boot partition of the SD card, rebooted to Recovery mode and then booted to NC's stock ROM. NC is still using the tiny boot partition on the SD card as my external storage instead of the much larger CM7 partition. This was the same partition that was under 'My Files / Memory card' before I flashed so nothing has changed. I did this twice to double-check.
Am I doing this wrong?
Click to expand...
Click to collapse
Yes you are doing it wrong. You need to flash that file with a CWM card, not put in the boot partition of your SD. And since you did that, you need to re-flash your latest ROM on SD to correct your mistake. (I will edit my instructions to make it a little clearer that you use CWM to flash that file.)

I got NC stock ROM to see my SD card partition by following item A10. That is most excellent and thanks again!
Unfortunately, I no longer see the boot partition when I attach NC to my computer whether NC is running off stock ROM or CM7. My guess is that this is due to my failed attempt to flash from my CM7 SD card yesterday. Am I right?
I thought I could reverse that by copying the update-stockemmc-vold-fstab-return-to-stock.zip file to CM7's boot (and then booting to the recovery mode) but that seemed to have nothing.
If I understand your previous message correctly, I should re-do my entire SD card but... I have already spent a few hours downloading and customizing the Android apps. Is there a way to preserve all that before Win32diskimager destroys the contents of the SD card?
Is there a way to manually mount the /etc folder from a unix prompt and alter the file?
Does it even matter if I don't see boot while I attach NC to a computer? Are there any caveats to 'let it be'?
Questions, questions and more questions...
That leads me to the obvious question, is there a book that explains Android to someone who is not interested in programming it but wants to understand the architecture and design of the OS (and custom ROMs)?
Thanks for being patient with all these n00b questions.

andrandom said:
I got NC stock ROM to see my SD card partition by following item A10. That is most excellent and thanks again!
Unfortunately, I no longer see the boot partition when I attach NC to my computer whether NC is running off stock ROM or CM7. My guess is that this is due to my failed attempt to flash from my CM7 SD card yesterday. Am I right?
I thought I could reverse that by copying the update-stockemmc-vold-fstab-return-to-stock.zip file to CM7's boot (and then booting to the recovery mode) but that seemed to have nothing.
If I understand your previous message correctly, I should re-do my entire SD card but... I have already spent a few hours downloading and customizing the Android apps. Is there a way to preserve all that before Win32diskimager destroys the contents of the SD card?
Is there a way to manually mount the /etc folder from a unix prompt and alter the file?
Does it even matter if I don't see boot while I attach NC to a computer? Are there any caveats to 'let it be'?
Questions, questions and more questions...
That leads me to the obvious question, is there a book that explains Android to someone who is not interested in programming it but wants to understand the architecture and design of the OS (and custom ROMs)?
Thanks for being patient with all these n00b questions.
Click to expand...
Click to collapse
You do not need or want to re-set up the whole SD installation. Just put the same CM7 zip file back in the boot partition and boot to SD recovery. It will put the correct vold.fstab back on the SD. You will not lose any settings or apps you have already set up. (And putting the return to stock zip there was also the wrong thing to do. The vold.fstab for stock and CM7 are different. But don't worry, it will fix that too.)
You are not supposed to see the boot partition on the PC when you plug the nook in with the cable. You are only supposed to see 'emmc' and 'sdcard'. Under the original setup, your stock system thought the boot partition was 'sdcard' and that was why you saw it on your PC. Since you modified stock to see partition 4 as 'sdcard', partition 4 is what the PC sees, not the boot partition.
Most people have to physically take the card out of the nook and put it in the PC to see the boot partition on the PC. If you don't want to do that, use my script in item B4. But since you are on CM7, you will not be adding many things to the boot partition to install with SD recovery in the future. So it is probably best to leave things be.
And I don't know of any books to help you.
Sent from my Nook Color running ICS and Tapatalk

That is excellent news!
A bit of playing around with Astro tells me that I was wrong about seeing the 'CM7 SDCARD' partition when I was on CM7 ROM. I am only seeing the boot. Anyway, I am going to flash the CM7 ROM again and I am hoping it would fix everything.
Also, yes, I can see the boot partition when I put the SD card directly on my computer but I was also able to see it when I hooked up the NC to my computer via USB before I did my unintended tweaks but... I'll survive.
I'll be back after I flash. (Famous last words??)

Mission accomplished!
Thanks again for all your help.

For future reference after you alter stock's fstab... all you have to do is:
mkdir /sdcard/boot (only have to do this one time)
mount /dev/block/mmcblk1p1 /sdcard/boot (do this every time you want to put something on the boot partition)
put anything you want on boot partition in /sdcard/boot

DizzyDen said:
For future reference after you alter stock's fstab... all you have to do is:
mkdir /sdcard/boot (only have to do this one time)
mount /dev/block/mmcblk1p1 /sdcard/boot (do this every time you want to put something on the boot partition)
put anything you want on boot partition in /sdcard/boot
Click to expand...
Click to collapse
Yes, there is one big advantage to using that method. I think it allows the boot partition to be seen not only on the nook, but also on the PC when you plug in the usb.

leapinlar said:
Yes, there is one big advantage to using that method. I think it allows the boot partition to be seen not only on the nook, but also on the PC when you plug in the usb.
Click to expand...
Click to collapse
We could probably come up with a symlink to /dev/block/mmcblk1p1 to /sdcard/boot and avoid having to mount it everytime as well.

DizzyDen said:
We could probably come up with a symlink to /dev/block/mmcblk1p1 to /sdcard/boot and avoid having to mount it everytime as well.
Click to expand...
Click to collapse
Thank you Dizz, your suggestion got me to thinking and I was able to come up with an init.d bash script that does the trick. I just temporarily mounted sdcard and created the sdcard/boot directory and the mounted the boot partition to it, then unmounted sdcard so it could be mounted again by the system later in the boot sequence.
The only problem is now sdcard will not mount on the PC using UMS mass storage. Must be because of having a second mount within the mount. But it does mount with MTP. But that may be acceptable. I will test some more, including using Goo Manager tomorrow.
EDIT (6-21): Goo Manager works. But I think I have figured out why sdcard is not mounting in UMS. Once it is mounted in my script and the boot partition mounted under it, it cannot be unmounted. And since it cannot be unmounted, it cannot be mounted later by the system as vold. If it cannot be mounted as vold, it does not show in UMS. For now I think I will leave it as I have it in Rev 2 of my script (symlinking to the root directory with full r/w permissions). If people want to see the boot partition on the PC, just use my modified for CM9 NookColorUMS available in my tips thread.
Sent from my Nook Color running ICS and Tapatalk

Help!
When CM7 is running, my computer is no longer mounting any of the partitions when I connect NC to my computer via the USB cable.
If the NC stock ROM is running, my computer mounts all three partitions (MyNook..., boot and CM7SDcard) but calibre is not recognizing the external partitions for transfers.
Further, when I boot to my NC stock ROM, I am no longer seeing my SD card's contents in the NC's library.
This may have something to do with the fact that NC stock ROM seemed to have updated itself to 4.1.3.
Should I re-run the scripts again or am I missing something else?

When it was updated to 1.4.3, you lost the emmc mods. Just re-flash my zip with the CWM SD. You may have lost CWM on emmc too.
On CM7, you have to select the turn on storage button after you plug it in. It is not automatic like stock. Pull up the notification area and touch the turn on button.

Darn, I forgot about that 'USB' option under notifications. Enabling it allows me to find the partitions. I will run your scripts again when I find a spare mUSB card.
Thanks again for your help!

Nook Color with CM7 - Boot-looping

I changed the Android ID on my Nook Color (with Titanium Backup Pro) and now it is boot-looping, at the point where the arrow head moves around in a circle. It is running CM7, but I'm sure the rom is at least a year old. I think it has CWM recovery. How do I get to recovery and what should I do?
[edit] I found this thread and will see if there is something I can use.[/edit]

I pulled the microSDHD from the device and I can read the boot partition on my PC. Before I attempt repair, I want to copy a few data files from the SDCard's data partition, but I do not see it. How do I mount the SDcard partition so that I can copy the files? I know how to do this once I can successfully boot to the Android desktop, but not without the desktop.
I looked through verygreen's SDCard installation instructions here and I can execute boot into recovery, but that just looks for update files and shuts down. I did not get a menu to allow me to mount the data partition via USB for the PC to read or for any options at all.

I have a bootable SDCard (verygreen's) and removed it to boot from emmc. That works, so the problem is on the microSDHC. When I insert the microSDHC (8GB) card in the card reader on my PC, I see the first three partitions are healthy and the last (5.9GB) is not. The only partition that I can assign a drive letter to is the first partition, Boot. Is there any repair I can do to that forth partition?