Database Users

[TUT] T-Mobile UK Upgrading/root/lag fix and De-branding.

I take no credit for any of this work. I have added it all to one post to help make life a little easier for those who are wanting help in getting rid of any need of waiting for T-Mobile to release any firmware again. Credits will be added to all post at the bottom of the respective page. This TUT will also work with other networks.
If you have 3 Button Download mode you can jump to page 2.
Post 1: 3 Button Download Mode.
Post 2: Upgrade to Froyo.
Post 3: Rooting and lag fix.
Post 4: De-Branding.
3 Button Download.
I have run out of time to add this today i will finish off tomorrow. For now follow this http://forum.xda-developers.com/showthread.php?t=821698

Upgrade to Froyo.
PRELIMINARY NOTE:
[WARNING!] Do Not flash Any ROM (firmware) until you can get the 3 buttons DOWNLOAD MODE working, even with this Kies trick.
If you want to test the 3 buttons download mode then notice that you can switch back to normal mode by pulling the battery out and then back in. At the next boot the phone will be back in normal mode.
LAGFIX USERS:
[WARNING!] Remember to disable lagfix before to update.
This will avoid filesystem errors that may occurs at the boot of the new flashed firmware.
INSTRUCTIONS:
1) Download latest Kies Registry Patcher, tool is attachment. Note: It require Microsoft .NET Framework 3.5 or later version.
2) Update Kies to 1.5.3.10103.102.
3) Launch Kies Registry Patcher; If you patched the dll in the past with an older version of the patcher then be sure to launch new release as administrator since it have to revert the dll to the original version as the patch isn't needed anymore (Right click on application > Run as Administrator).
4) Launch Kies and connect your phone; Wait for Kies to recognize it properly.
5) You have 2 possibilities now:
5a) Drop down the combo-box "Spoof Product Code as" and select the wanted one. It should automatically fill the "Spoof Software Revision as" textbox with the needed data necessary to find your update.
This feature was added in order to give all the opportunity to use the needed product code. (Special thanks to MCOGW that shared with me his database of product codes/sw revisions).
The label above will be completed with the country related to the chosen product code.
5b) From patcher select:
File > Load Backup
Open the backup that you want to use (e.g. kies-backup-XEU.xml if you want to spoof your phone as XEU, or if your phone is XEU yet and you want to flash it again).
6) From patcher answer "YES" in order to apply the registry update.
7) From Kies you can now update as normal.
Remeber that this patch will remain ACTIVE until you set "Enable Spoof" field to False!
It's not a problem but ater you update the phone it's suggested to put that value to false so the patch become inactive.
Full Post: http://forum.xda-developers.com/showthread.php?t=835628
Credits:
Nodial

Root/Lag fix.
Download the attached files, place them on your memory card and install them on your handset by navigating to them in My Files app and click on them to install.
Once installed run z4root first, then run OCLF.2.3.0 and except Superuser permissions.
Inside OCLF2.0 application click on the following:
1st: Install EXT2 Tools (follow instructions)
2nd OneClickLagFix V2.2+ (follow instructions)
Congrats you now are rooted and have applied a lag fix.
Full Post z4root: http://forum.xda-developers.com/showthread.php?t=833953&highlight=Z4root
Full Post OCLF: http://forum.xda-developers.com/showthread.php?t=833953&highlight=oclf
Credits:
RyanZA
z4ziggy
Sebastian Krahmer's rageagainstthecage

De-branding.
To truly de-brand you need to get rid of the branded product code and have the correct CSC. Follow the steps below.
[WARNING] Make a full backup of your \efs folder just in case you go wrong or any errors occur.
You will need to be rooted and have the root explorer app installed from the market.
Copy your \efs folder to your pc and open nv_data.bin with note pad, Search for TMU and replace with XEU. If you can not find TMU try KOR. Save the file and and copy it back to your \efs folder on your handset. Delete the nv-data.md5 file off the handset and reboot. repeat steps with the nv_data.bak file.
Once completed change your CSC to XEU by typing *#272*(yourimei)# and click on XEU.
Now when Samsung release a new update you will get it straight away.
Sorry if I have missed any people in the credits. Please post with name and post number if poeple need to be added.

Hey I want to get Froyo, tired of waiting for T-mobile but i dont have the 3 button combo on my phone so is there any safe way of doing this or fixing 3 button....?

hey n1kon nice idear b4 barry shuts down the forum on T,M
have you used the root/lag fix ??

Great post, tired of waiting for t-mobile to release 2.2
Thanks.

n1kon said:
Upgrade to Froyo.
5a) Drop down the combo-box "Spoof Product Code as" and select the wanted one. It should automatically fill the "Spoof Software Revision as" textbox with the needed data necessary to find your update.
This feature was added in order to give all the opportunity to use the needed product code. (Special thanks to MCOGW that shared with me his database of product codes/sw revisions).
The label above will be completed with the country related to the chosen product code.
6) From patcher answer "YES" in order to apply the registry update.
7) From Kies you can now update as normal.
Credits:
Nodial
Click to expand...
Click to collapse
I'm rather new to all this and before I attempt to update my T-Mobile Galaxy S using the described 5(a) option, I would appreciate some advice, please.
I understand the instructions right up to the end of para 5(a) but at this point there is no "yes" button to click. However, there is a "Read Registry" button. Presumably I click this and will then be asked the click a "Yes" button to proceed with the update.
What then happens? What should I expect to see on the PC and on my phone?
Some step-by-step instructions would be much appreciated to boost my confidence!
P.S. I've already checked that I have the three-button system restore active on my phone.

Ain't done no root because I wil be ****ed if it bricks and I don't know no way of rooting without restore mode.
Sent from my GT-I9000 using XDA App

I've been running 2.2 on my T-Mobile UK Galaxy S for some time, but have never used or even installed Kies. I just installed the relevant USB drivers, then flashed a ROM I've downloaded from mirrors linked here with Odin3 (I've always had download mode working properly). Currently I'm using JPO with SpeedMod Kernel K10H, which provides root.

Hi i upgraded via the kies registry way all works well apart from i cant find where to switch between 2g and 3g. It was in mobile networks on 2.1 but its not there now also having issues using myplayer and beebplayer once again they worked in 2.1 but not on froyo atm. other then that alss good

I used this guide to fix the 3 button combo issues - http://forum.xda-developers.com/showthread.php?t=785201

It still is in there 2g is gsm
Sent from my GT-I9000 using Tapatalk

blazevxi said:
I used this guide to fix the 3 button combo issues - http://forum.xda-developers.com/showthread.php?t=785201
Click to expand...
Click to collapse
Im looking into the safest one to use but am at work right now
Sent from my GT-I9000 using Tapatalk

I use both root and lag fix
Sent from my GT-I9000 using Tapatalk

Surely the easiest way to debrand is to just flash a new ROM via ODIN?

Is that way safe, dont want to brick my phone?

-Elvin- said:
Is that way safe, dont want to brick my phone?
Click to expand...
Click to collapse
I've done a branded Orange and Vodafone by flashing XXJPO via ODIN.
It's very hard to totally brick your phone with ODIN, but there can be complications.
Before you do anything, make sure you have working 3br and download mode. If you don't have it, I don't recommened using Kies or ODIN.

Rawat said:
Surely the easiest way to debrand is to just flash a new ROM via ODIN?
Click to expand...
Click to collapse
Flashing with odin will not allow u to update with kies when the next release is issued as your product will stay the same and your software versions will be wrong so you will need to use odin again. Plus if odin is used wrong it can brick you phone
Sent from my GT-I9000 using Tapatalk

n1kon said:
Flashing with odin will not allow u to update with kies when the next release is issued as your product will stay the same and your software versions will be wrong so you will need to use odin again. Plus if odin is used wrong it can brick you phone
Sent from my GT-I9000 using Tapatalk
Click to expand...
Click to collapse
Nope, if you flash a full ROM via ODIN, including the CSC, it'll work fine. It'll even work on kies (although i don't know why anyone would want to do that )
Kies can also brick your phone >_>;

Updating to 2.3.4 firmware - if you don't want to root

HI
This is Just for People who want to flash 2.3.4 firmware or any other firmware but don't want to root their phones like me.
Again All Posts are within XDA and Due Thanks to the OP's and DEVS
I'll Try to be as informative and clear as possible ( Its more for the newbies )
First off all it has been stated this 2.3.4 is leaked and not official
So lets Begin
1. Install latest Kies of samsung > connect your phone and make sure all drivers are Installed and your phones is recognised in Kies > Backup if you wanna
2. Close Kies ( make sure its not running in the system tray) > Install ODIN
Get Odin v1.85 from here: http://www.multiupload.com/1RTGSE061G
Just extract Odin folder and keep the odin3.ini file in it.
How to USE ODIN in SECOND POST
3. Download your 2.3.4 Firmware ( or any other firmware you wish to flash)
a) Download Link Stock XXKG1 : http://www.multiupload.com/2EMBQMYF4V (via ficeto) or If you can find other links
and Extract It > you should have four files:
b) CODE_I9100XXKG1_CL349526_REV02_user_low_ship (goes into PDA section)
GT-I9100-CSC-MULTI-OXAKG1 (Goes into CSC section)
MODEM_I9100XXKG1_REV_02_CL1034110 (Goes into Phone section)
u1_02_20110310_emmc_EXT4.pit (not required)
4. Open ODIN and put the files in the respective TABS > Do not change (tick or untick any other boxes) read the second post by intratech
5. Put phone in Download Mode
a) DOWNLOAD MODE - Volume Down + Home Button + Power Button
b) Volume Up to get into Download Mode
c) Connect phone and wait till First Box in ODIN turns Green
d) Click Start and wait till phone flashes and Reboots automatically ( can take up to 15 mins)
e) Once phone reboots you are Done you can close ODIN
ORIGINAL POSTS, OFFICIAL FIRMWARES and CARRIER FIRMWARES HERE
Thanks to - INTRATECH,TANMAY,FICETO and the DEVS CONCERNED
PS : If I have missed out anything let me Know and I will update

INTRATECHS GUIDE TO FLASHING WITH ODIN - Scroll Down to see the screen shots in HIS POST
Flashing Firmware with Odin
1. Just download the firmware version you want from above and extract the .tar file in the archive and save it somewhere
2. Reboot your phone to download mode.
To get download mode shut down the device. After it shuts off completely simultaneously press the Down volume key+ Home button + press the power button .
You should see a warning asking you to press volume up if you want to continue or volume down to cancel, press volume up. You are now in download mode!
3. Start Odin
4. Click on the PDA button and browse to the .tar file that you extracted in step 1
If the package has more than one .tar archive then they will be labelled with PDA, Phone/Modem and CSC. Just put them in the corresponding section of Odin
5. DO NOT PUT .PIT FILE AND DO NOT, I REPEAT, DO NOT TICK REPARTITION.
Anyone ask about .pit file is a moron
Should look like this screenshot
http://img153.imageshack.us/img153/5705/odinm.jpg
If the package has 3 files it should look like this:
http://img94.imageshack.us/img94/8290/odinxm.jpg
Regardless of firmware version it's still the same methodology
6. Connect the USB cable and wait for the ID:COM section to turn yellow
7. Click start to flash
8. Do not disconnect the cable or turn off the device, it will reboot when it finishes.
It will not wipe your phone if you flash as recommended

Will I loose all my data and programs?

let me be the first to thank you
i am coming from iphone4 so all these terms and apps are new to me, and while i can use the search function a lot of times it takes several pages of read-thru to piece together what you have put in 1 concise post
btw i love the SG2 and android platform, steve jobs can toss my salad

If you flash any 2.3.3 you don't seem to loose any data... but yeah updating to 2.3.4 you do loose data and programs.
I didn't have many programs, but market restored most of them from me, and good to backup first.
Also kies gives me that I can't update firmware maybe cause its the latest one and it don't recognise the firmware.
Please be aware this is a leaked version, so if you want you could wait for the official one, I so far had no problems whatsoever

Just one noob question, SII being my first android phone, i assume that in order not to lose warranty you still have to use USB jig to reset rom counter if something bad happens, right ?

Sp1tfire said:
Just one noob question, SII being my first android phone, i assume that in order not to lose warranty you still have to use USB jig to reset rom counter if something bad happens, right ?
Click to expand...
Click to collapse
Sorry I have no clue about that But I guess you could always flash the carrier branded firmware from INTRATECH's posts.. links in my first post as well.
I guess it only applies if you root your phone (I could be wrong).
Here is a link if its any good to you
[HOWTO] reset custom binary counter in download mode

obionenairobi said:
Will I loose all my data and programs?
Click to expand...
Click to collapse
With low packages you will so yes.
Good work tfn.

Intratech said:
With low packages you will so yes.
Good work tfn.
Click to expand...
Click to collapse
All thanks to you Mate , It mostly all leeched off your posts

Sp1tfire said:
Just one noob question, SII being my first android phone, i assume that in order not to lose warranty you still have to use USB jig to reset rom counter if something bad happens, right ?
Click to expand...
Click to collapse
If you are using stock kernel there is no counting in custom binary,so no problem with your warranty.You can check your counter if you go to download mode.By the way usb jig is always usefull.
Regards
Sent from my GT-I9100 using Tapatalk

afilopou said:
If you are using stock kernel there is no counting in custom binary,so no problem with your warranty.You can check your counter if you go to download mode.By the way usb jig is always usefull.
Regards
Sent from my GT-I9100 using Tapatalk
Click to expand...
Click to collapse
Thanks for the info

Is it possible to use another CSC from older stock releases together with this? ie, flashing this, and then after that flashing the multi CSC "MultiCSC OXXKF1" for instance? The reason im asking is that ppl have reported this rom to not include the nordic keyboard's for swype etc, and thats sort of a gamebreaker for me.

rulleeeee said:
Is it possible to use another CSC from older stock releases together with this? ie, flashing this, and then after that flashing the multi CSC "MultiCSC OXXKF1" for instance? The reason im asking is that ppl have reported this rom to not include the nordic keyboard's for swype etc, and thats sort of a gamebreaker for me.
Click to expand...
Click to collapse
I dont see any reason why not.
Sent from my GT-I9100 using Tapatalk

tried it, and it worked to install that CSC, but i thought the keyboard layouts were included in that but i was misstaken, guess ill go back to the KF3 nordic release, meh

password request
after i install it asks me to confirm password.i dont know anyone help me please

xboxfan said:
after i install it asks me to confirm password.i dont know anyone help me please
Click to expand...
Click to collapse
I believe it must be your samsung account password.. or unless you had a security lock password.. Try one of those

xboxfan said:
after i install it asks me to confirm password.i dont know anyone help me please
Click to expand...
Click to collapse
Whatever the pin unlock code that you use to unlock the device in the password that you need.

tfn said:
If you flash any 2.3.3 you don't seem to loose any data... but yeah updating to 2.3.4 you do loose data and programs.
I didn't have many programs, but market restored most of them from me, and good to backup first.
Also kies gives me that I can't update firmware maybe cause its the latest one and it don't recognise the firmware.
Please be aware this is a leaked version, so if you want you could wait for the official one, I so far had no problems whatsoever
Click to expand...
Click to collapse
tanx so much!!!..i`m downloading...keep it up bro

There is one thing I don't understand how to do. Before I flash my firmware with the new 2.3.4 version, I would like to take a copy of my existing firmware from my phone first and save it to my PC. So that I have the option of putting my phone back to how it was if for some reason I want to revert my phone. I understand that I would need to buy a jig to reset the update counter.
So is it possible to save my existing firmware to my PC first?
I did try looking at the download page but there were so many different countries and carrier versions that I found it confusing. I am stock KF3 uk unbranded O2 still running 2.3.3
Thanks

Thank you tfn. Great instructions, I am loving the new update.

[GUIDE] How to use Odin for GT-I9070

Odin is the saviour tool for all Samsung devices. The method for flashing by Odin differs from device to device.
This thread will give step by step instructions on how to flash a stock rom from Odin on the GT-I9070/p :
A. Download Odin tools from here : http://d-h.st/3zJ
Pass : shaaan
B. Download the stock rom from www.samfirmware.com
Setting up Odin :
1. Make sure you have installed the necessary drivers for this device. The drivers can be installed from within KIES or seperately. (I will upload the drivers shortly).
2. Run Odin as administrator.
3. Setting up the files is divided in two types depending on the firmware type :
a. If the firmware is a multi package file, put the files in the corresponding sections.
ie. CSC file in CSC section, PDA file in PDA section.
b. If the firmware is a single package, add the single file in the PDA section.
4. Now that Odin is setup, put the phone in download mode. To do that, power off the phone and press 'home+power+volume down' buttons together. Keep the buttons pressed till Download mide appears.
5. Now that Odin and the phone are setup, connect the phone to the device. Odin will detect the device and show something like 'com port (1)'
6. Flash the device.
7. The flash will take 5 minutes for a full flash on average.
8. When the flashing is complete, DO NOT remove the device until Odin shows ' PASS '.
9. The device will reboot. Remove the device, go to recovery mode and do a factory/data reset.
That's it. Happy flashing peeps..!!

Awesome guide mate - messing around with our device without Odin is risky !

This should be sticky. A lot of people is asking how to revert to original FW, or similiar questions that is connected to reverting. And it is almost at the end of forum, and thay cant see it.

I pmed the mods to do it. But they won't budge..
Please pm them..

Nice guide!!!
And adding images would be a nice option.
And plz add a point which tells which buttons to press like
"Re-Partition" ,"Auto Reboot","F.Reset Time" ,"Flash Lock"......
Sent from my GT-I9070 using xda premium

Very good guide,good work !
It may be better if you add some images

atishey23 said:
Nice guide!!!
And adding images would be a nice option.
And plz add a point which tells which buttons to press like
"Re-Partition" ,"Auto Reboot","F.Reset Time" ,"Flash Lock"......
Sent from my GT-I9070 using xda premium
Click to expand...
Click to collapse
From what I was able to find in other guides it is ONLY 'Auto Reboot' and 'F. Reset Time' to be checked.
All others to be unchecked.
There are some posts not to bother with that .pit file that is inside Odin .zip file.
Odin package from sammobile got 2 .pit files for 8GB - GT-I9070_EUR_XX_8G and GT-I9070_EUR_XX_8G_20111220_KL6 and one for 16GB
(at least paired with XEO region XXLD1) not only that one we got in link form 1st post.
I was also able to find some info that if you use .pit check also 'Re-Partition'.
Now I am curious about if It would be good idea for me to actually Re-Partition my phone - bought it used (not new) and my PC detects only 4GB of internal SD. Will it increase custom binary counter? (so far it is at 0 and I would rather keep it that way)
Is it going to fix that issue so I will be able to use all 8GB (minus system partition)?
If so how to use it and what .pit file to take?
.pit only, re-partition only and run it once, then single-package as PDA with reboot and F. Reset on another flash run?
Or maybe all at once?
BTW you guys ROCK.
Rooted SGS i9000 2 years ago with this forum and now I am very close to do it again with SGSA.

th3cr0w said:
From what I was able to find in other guides it is ONLY 'Auto Reboot' and 'F. Reset Time' to be checked.
All others to be unchecked.
There are some posts not to bother with that .pit file that is inside Odin .zip file.
Odin package from sammobile got 2 .pit files for 8GB - GT-I9070_EUR_XX_8G and GT-I9070_EUR_XX_8G_20111220_KL6 and one for 16GB
(at least paired with XEO region XXLD1) not only that one we got in link form 1st post.
I was also able to find some info that if you use .pit check also 'Re-Partition'.
Now I am curious about if It would be good idea for me to actually Re-Partition my phone - bought it used (not new) and my PC detects only 4GB of internal SD. Will it increase custom binary counter? (so far it is at 0 and I would rather keep it that way)
Is it going to fix that issue so I will be able to use all 8GB (minus system partition)?
If so how to use it and what .pit file to take?
.pit only, re-partition only and run it once, then single-package as PDA with reboot and F. Reset on another flash run?
Or maybe all at once?
BTW you guys ROCK.
Rooted SGS i9000 2 years ago with this forum and now I am very close to do it again with SGSA.
Click to expand...
Click to collapse
It is normal to have 4GB on internall SD. The rest of it goes to system partition, application partition and RAM I think...

shut_down said:
It is normal to have 4GB on internal SD. The rest of it goes to system partition, application partition and RAM I think...
Click to expand...
Click to collapse
googled a bit more and found it out too :crying:
BTW - both of those 8GB .pit files are identical (according to 'comp' tool in windows) so there is no reason to use re-partition - other than sth went totally wrong and you are trying to recover from brick or sth serious as this .pit file is already on your device.
Just flashed unbranded stock for XEO region - original one was branded.
NOTE to anyone who is still thinking about safety of this method:
After initial reboot - when it was reconfiguring in recovery mode - or however you will call it (just before odin should say 'pass' - still in that little font screen) windows started to reinstall usb drivers - odin log in bottom corner said 'disconnected' and even then my newly flashed ROM is working as it should. I would rather keep it connected till Odin confirms all went as intended but in case of similar issue - do not get heart attack

odin is used for flashing stock roms only???

Kulwinder Singh said:
odin is used for flashing stock roms only???
Click to expand...
Click to collapse
nope it can also be used to flash custom Roms and kernels though flashing custom kernels via odin will increase your bin counter !

Hello guys...
How are you? I´m new on the i9070 threads!!! I´ve had others phones before, like SG2, xperia sola, live with walkman... so, i need the password to descompress odin... i search on thread but i don´t found it...
SORRY I found the password... shaaan

Of what I understand, can I test an unlimited number of stock firmware and the binary counter remain 0?
If I flash an unbranded firmware can I use SIM cards from other providers?
Now my phone is branded and I can not use SIM cards from other providers.
Thanks.

Kulwinder Singh said:
odin is used for flashing stock roms only???
Click to expand...
Click to collapse
Read please, sir!
http://forum.xda-developers.com/showthread.php?t=1985199
:laugh:

Someone help me? LINK

Hi i have downloaded the russian jelly bean 4.1.2 package but when i tries to flash it using odin3 v1.83 it shows me "The Parameter is incorrect" why???

sonimayurp said:
Hi i have downloaded the russian jelly bean 4.1.2 package but when i tries to flash it using odin3 v1.83 it shows me "The Parameter is incorrect" why???
Click to expand...
Click to collapse
Try to remove .md5 from filename.

shut_down said:
Try to remove .md5 from filename.
Click to expand...
Click to collapse
Hmm it worked thx..

Flash JB
Hi, I want to flash Jelly Bean , do i need to use the pit file , or just select one package and then select the rom??
Edit : flashed

This version of Odin does not work when flashing JB to my device.
I successfully used Odin3v3.07 from this post: http://forum.xda-developers.com/showthread.php?t=2086965
Please update this guide. I spent quite a lot of time trying to figure out what was wrong.
Thanks

Flashing a stock rom on my i9505

Hello, i recently purchased my galaxy s4 from online which came from Honk Kong, Because it is from there i believe it has the honk kong/chinese firmware on it (I9505ZHUAME3), I live in Australia so i want to flash it with its firmware (I9505XXUBMEA),so i have downloaded the australian firmware and kernel files, my phone is currently not rooted (i dont believe i need to root for a stock firmware?), Just wondering when i put my phone in download mode and open up odin, do i only need to put in the firmware file into pda or will i need to get a csc file or whatever the 'phone' button file is for aswell. Just making sure as i only got it the other day and dont want to screw it up. Thanks in advance!

eNormini said:
Hello, i recently purchased my galaxy s4 from online which came from Honk Kong, Because it is from there i believe it has the honk kong/chinese firmware on it (I9505ZHUAME3), I live in Australia so i want to flash it with its firmware (I9505XXUBMEA),so i have downloaded the australian firmware and kernel files, my phone is currently not rooted (i dont believe i need to root for a stock firmware?), Just wondering when i put my phone in download mode and open up odin, do i only need to put in the firmware file into pda or will i need to get a csc file or whatever the 'phone' button file is for aswell. Just making sure as i only got it the other day and dont want to screw it up. Thanks in advance!
Click to expand...
Click to collapse
This should answer all of your questions. If you are still unsure, let me know.
"How to do it:
Step 1) Turn OFF your mobile and go to Download Mode by pressing and holding the Volume Down + Home Buttons together for few seconds followed by Power button then proceed with volume up.
Step 2) Now open ODIN on your PC and connect your Galaxy S4 to your computer.
Step 3) Once your phone is successfully connected to your PC, the ID:COM box on ODIN will turn blue (or yellow) and will show the COM port number.
Step 4) unzip the downlowded file (from second or third post), u will get a Home.tar file.
Step 5) click on pda (in odin) and choose the file "Home.tar"
Step 6) check "Auto Reboot" and "F. Reset Time" options and make sure that "Re-Partition" is unchecked
!!!!DO NOT CHECK "Nand Erase All" IN ANY WAY!!!!
Step 7) Click on Start button in ODIN window to start the flashing process. The process will take few minutes to complete.
DO NOT UNPLUG USB CABLE WHILE EXECUTING THE PROCESS, YOU MAY BRICK YOUR PHONE!
Step 8) When the installation is completed, you read a "Reset " then a "Pass". your phone will restart (first boot will take a longer time so don't panic)"

C.Sweat said:
This should answer all of your questions. If you are still unsure, let me know
Click to expand...
Click to collapse
I did view this before, but i was unsure if it did what i wanted, i want it so if i did buy my galaxy s4 in australia it would have all the same stuff like csc and pda etc ,

eNormini said:
I did view this before, but i was unsure if it did what i wanted, i want it so if i did buy my galaxy s4 in australia it would have all the same stuff like csc and pda etc
Click to expand...
Click to collapse
Thats fine but you need to read throughout the whole thread and use the search function to find answers to your questions. See here within the thread for your answer.
If ive been of any help, hit the "Thanks" button :good:

C.Sweat said:
Thats fine but you need to read throughout the whole thread and use the search function to find answers to your questions. See here within the thread for your answer.
If ive been of any help, hit the "Thanks" button :good:
Click to expand...
Click to collapse
Thanks heaps, one last thing, do i have to be rooted?, i am currently running the stock firmware.

eNormini said:
Thanks heaps, one last thing, do i have to be rooted?, i am currently running the stock firmware.
Click to expand...
Click to collapse
No
↙

C.Sweat said:
No
↙
Click to expand...
Click to collapse
Thankyou for the help, appreciate it

eNormini said:
Thankyou for the help, appreciate it
Click to expand...
Click to collapse
No problem. Good luck

[GUIDE] Recover Samsung Device from Bootloop or Back to Stock Rom

I wanna share my knowledge here
Learning from my experience using Samsung's devices, I found similarities in the way of reversing Samsung devices to stock rom.
So this guide should be practice for almost all Samsung devices
Ok, let's get started
First, download all these stuff
1. Samsung USB Driver or go to this Thread (install it)
2. Samsung Kies (install it)
3. Odin v.4xx or Odin v1-3 or go to this Thread (just open when need it)
4. And of course your stock rom
Download from here (choose the right stock rom and the newest depend on your model)
5. Extract the stock rom using winrar/7zip
-you should 3 files PDA_xx.tar.md5, Phone/Modem_xx.tar.md5 and CSC_xx.tar.md5 or more
-If you have just two files, .xxxx.tar.md5 & SS_DL.dll, i'll give it the guide too
Second, Go to download mode
- For device with Menu button : hold power button+menu button+volume down (vol -)
- For device without Menu button : hold power button+volume down (vol -)
For the 3 Files or more
- Go to download mode
- Plug your device to PC/Laptop
- Open Odin
- Choose PDA (browse it from your extracted stock rom)
- Choose phone/modem (browse it from your extracted stock rom)
- CSC (browse it from your extracted stock rom)
- If there's more files, just put it on the same box of the files names
- Check list auto reboot and f.reset time(look at the left)
- Click start and wait
- If success, should be writen "PASS" on left side
For 2 files only
- Go to download mode
- Plug your device to PC/Laptop
- Open Odin
- Just choose PDA and browse it the file(forget about SS_DL.dll or XX.dll file)
- Check list auto reboot and f.reset time(look at the left)
- Click start and wait
- If success, should be writen "PASS" on left side
If there's something miss or wrong, please tell me, I'll fix it this ASAP
And Let's helping people

Thank
Just great, it's what I need to restore my galaxy camera, :good::good::good:

pleko said:
Just great, it's what I need to restore my galaxy camera, :good::good::good:
Click to expand...
Click to collapse
you're welcome

So I know Im the new guy, but for the life of me have no idea how to choose the right firmware from the list on SamMobile.
It doesn't show my region there, and I have no idea how to tell which one is the latest for my camera.
I have attempted update through Kies and it does not allow me to do so saying that I am on the latest firmware.
I am comfortable on your instructions, I just don't know how to choose which one works for me.
I am located in the US.
Camera Model: EK-GC110
Build number: GC11UEAMC2
Any help would be awesome thanks!

BILLYB187 said:
So I know Im the new guy, but for the life of me have no idea how to choose the right firmware from the list on SamMobile.
It doesn't show my region there, and I have no idea how to tell which one is the latest for my camera.
I have attempted update through Kies and it does not allow me to do so saying that I am on the latest firmware.
I am comfortable on your instructions, I just don't know how to choose which one works for me.
I am located in the US.
Camera Model: EK-GC110
Build number: GC11UEAMC2
Any help would be awesome thanks!
Click to expand...
Click to collapse
you have registered to the Samsung firmware web, type your model on search bar, then choose international model or any model(same with yours) have the latest update, should be working, cause your model doesn't have simcard(WI-FI only model)

nasheich said:
you have registered to the Samsung firmware web, type your model on search bar, then choose international model or any model(same with yours) have the latest update, should be working, cause your model doesn't have simcard(WI-FI only model)
Click to expand...
Click to collapse
I have registered on the site. And when I search for EK-GC110 It presents me with a list of many download options.
Do the PDA and CSC Columns mean anything? If I choose for example the chinese ROM, will my download load my camera with the chinese language?

BILLYB187 said:
I have registered on the site. And when I search for EK-GC110 It presents me with a list of many download options.
Do the PDA and CSC Columns mean anything? If I choose for example the chinese ROM, will my download load my camera with the chinese language?
Click to expand...
Click to collapse
no, PDA and CSC just like file name,
yes, if choose Chinese rom, 90% possibility is the language will be Chinese too

nasheich said:
no, PDA and CSC just like file name,
yes, if choose Chinese rom, 90% possibility is the language will be Chinese too
Click to expand...
Click to collapse
so i dont have to match my AMC2 too anything?
I can just pick anyone that supports my language?

BILLYB187 said:
so i dont have to match my AMC2 too anything?
I can just pick anyone that supports my language?
Click to expand...
Click to collapse
no, just choose the stock rom you like