I have a brand new Nook Color the Software Version (in about my Nook) says 1.2.0. what is the easyest way to go about rooting? is there a specific version of CM7 that I should use? What is the best rooting method or system to use? I am totally new to all this so some step by step instructions or detailed informatio would be great!!! Thanks for all you guys help!!!
There are several decisions you need to make before you start. Do you want to have dual boot (meaning that you can switch between stock rom and another rom of your choosing? In these case you would be running the non stock rom from the sd card. Or, do you want to go full non stock rom (emmc)? There are different methods for each.
After you decide this, you need to decide which custom rom you would like. The most used are CM7, phiremod and MIUI. CM7 is the most update one and has a lot of following and development.
If like you mention on your post you are looking at using cm7, then I suggest you start with the latest stable version 7.1 (which was released a couple of days ago). You can find the files and instructions in this post and the detail instructions here
Hopefully this can help you, you could also look around in the android development section in the forums for further info and/or wait for more detailed info from more experienced rooter than me
Thanks for the Advise/ information, so if I go dual is it very complicated to switch from one to the other? is there an advantage to being able to switch back and forth? I currently have a 2gb sd card that should be big enough right? Once again thnks for the help..........
Does anyone else have input or feedback???
Just last week I installed CM7 on an SD card in my Nook Color. It's been great so far. I figure I'll try it on the SD card for a while before I do anything more permanent like installing to the internal memory.
When you install to the SD card, you boot back into the "stock" OS by just removing the card.
As for the size of your SD card, I think 2GB is large enough, but that depends on how many apps, etc. you plan to have on it.
When you install to the SD card, you boot back into the "stock" OS by just removing the card.
Click to expand...
Click to collapse
I would not recommend doing that. The Nook card slot is a little fragile and excessive swapping will likely damage it. Mine gave out and I rarely remove the card as I have CM7 on the eMMC and only use the card for backups and upgrades. I had a hell of a time restoring the stock ROM so I could return it under warranty. If you are going to run from the card, set it up for dual boot so that you just pick which ROM you want to use when you boot up.
Related
My head is aching with the sheer amount of information it is trying to process. I got a Nook Color about a month ago but have been putting off using it because I am still trying to figure out how to do what I want to do.
I've been going over the threads on the dev forum and after reading a lot of the threads, I still can't find exactly what I need (or maybe I've found it but I just haven't realized it yet).
My Nook Color is running latest official update from B&N (meaning 2.2 and B&N apps).
Anyway here's what I need:
1. I need to be able to dual boot into either HC or a rooted gingerbread-based version of android (is this the clockwork 7 thing?) solely from an SD card
2. Should not do anything to the Nooks internal memory (meaning: won't void warranty)
3. The dual boot manager, HC and and gingerbread-based version of android should all run on sd card. nothing will be placed/done on the nook (is this it? i'm so confused i'm not even sure anymore --- http://forum.xda-developers.com/showthread.php?t=1045018)
4. The dual boot manager will still have the ability to install other custom roms on to the sd card when i put the zip file of the image on to the sd card (something like this: http://forum.xda-developers.com/showthread.php?t=1000957)
5. Should have the overclock thingamajig
Anyway, are there any solutions to this? the "Dualboot Phiremod / Honeycomb Image for SDcard" seems the closest so far but I can't figure out if it installs a rom manager into the SD card with which I can install newer versions of the overclock kernel or newer versions of the custom ROMS based on HC preview or newer version of the CM7 nightly image. gaaaah.
Please help >_<. I promise I'm not stupid. This is just like information overload and I seriously am having a real headache (not just figuratively) right now.
Follow the thread below. From it, you can install plain CM7 (the best known gingerbread rom) strictly onto your SD card. If you have multiple cards, you can try out the different flavors of CM7:
CM7 Stable (latest is 7.0.3); OR
CM7 Nightly (latest is 76); OR
Beta CM7 .32 kernel, though this one is still has some bugs.
Phiremod is a themed CM7 which I haven't tried, while the above are more plain vanilla android. Also use a Sandisk card if you have one as they seem to have better overall speed regardless of Class, at least 2gb size or bigger.
http://forum.xda-developers.com/showthread.php?t=1000957
Hi LBN1, thanks for the quick reply.
Does this work process allow me to install HoneyComb as well as a separate boot option?
I just realized that I'm actually looking for an SD dual boot of HC and CM7 w/ OC. Does this exist? >.<
Oh, this process is not for a dual booting SD card. It allows a rom on a SD card, and then take out the SD card and you can boot to stock B&N software, so it is a quasi dual boot so to speak. There are some actual dual boot options out there but I don't have any experience with any of them...
Same thing with Honeycomb roms, never tried any of them since from what I read they are still in early, beta stages meaning they really don't work as well as CM7.
LBN1 said:
Oh, this process is not for a dual booting SD card. It allows a rom on a SD card, and then take out the SD card and you can boot to stock B&N software, so it is a quasi dual boot so to speak. There are some actual dual boot options out there but I don't have any experience with any of them...
Same thing with Honeycomb roms, never tried any of them since from what I read they are still in early, beta stages meaning they really don't work as well as CM7.
Click to expand...
Click to collapse
Hehe... yeah I kinda figured that out What I had in mind was something along the lines of dual booting HC/CM7 via SD card and removing the SD card if I wanted to boot to the stock 1.2 (so it's a quasi triple boot) >_<
But thanks for your help!
I think the easiest thing you can do right now is to try the Phiremod/Honeycomb Dual boot sd image which I see you already found out. It wont change or touch your internal system so you are safe. Also its already prepared for you so you just need to burn the img into the sd.
If inserted, the sd image will boot to either Phiremod (which is really a themed version of CM7 7.02 - with the update provided in the same thread or to Honeycomb). I use it and works quite well!!!! It is fast also (provided you use the recommended Sandisk class 4 sd card) as it is overclocked from the sd which you also want.
When I want to use stock BN I just boot without the sd and thats it! I also rooted the internal BN as well to add overclock to the stock BN 2.2 and it is quite snappy when OC to 1.1 mhz.
Hi Garoto! that's good to hear! can you point me to the thread for rooting the internal BN and adding overclock to the stock 2.2? i want to try that as well
pryonix said:
Hi Garoto! that's good to hear! can you point me to the thread for rooting the internal BN and adding overclock to the stock 2.2? i want to try that as well
Click to expand...
Click to collapse
Sure no problem:
1. To root the 1.2 version Nook just follow the steps in this thread, it is not as complicated as it sounds:
http://forum.xda-developers.com/showthread.php?t=1054027
2. To install the OC Kernel I used this thread. Pretty simple process. After you root , go to the market and install ROM manager, then do flash clockwork and then reboot to recovery, then do update from zip in sd card and flash the OC Kernel. I used the 1,1 mhz as it is stable and really speed things up:
http://forum.xda-developers.com/showthread.php?t=1064095
pryonix said:
Hi Garoto! that's good to hear! can you point me to the thread for rooting the internal BN and adding overclock to the stock 2.2? i want to try that as well
Click to expand...
Click to collapse
Keep in mind, overclocking definitely technically voids the warranty (as does rooting). Since you mentioned it. Just as bad as installing stuff on the internal EMMC.
greenmky said:
Keep in mind, overclocking definitely technically voids the warranty (as does rooting). Since you mentioned it. Just as bad as installing stuff on the internal EMMC.
Click to expand...
Click to collapse
Haha yup... just wanted to know as a "just in case I feel brave enough to void my warranty" haha!
I just bought a Nook Color for my girl and wanna root and install a costum Rom...since this is my first time doing this to a nook color (i have done this to my G1,Vibrant and Asus transformer) i wonder what is the most stable Rom?
should i go with Cm7 or Honeycomb?
Keep in mind that i'm looking for stable Rom...i don't want to get my girl mad at me..
Thanks in Advance..
Get a microSD card, and install CM7 onto that. You protect the B&N system, so you won't void the warranty. The entire OS and apps sit on the SD card. The Nook will attempt to boot to the SD card first, so you're golden. Any time you want to be back in the B&N mode - just pull the SD card. No need to root or anything.
Go here for the easy-to-read steps on how to make it happen:
http://quinxy.com/2011/04/01/comple...on-the-nook-color/comment-page-3/#comment-944
Even if you were to mess things up you can always restore the stock rom because it boots from the SD card. That's what's so awesome. I would also agree with cm7. There is a sticky in the apps thread that has a good start on what apps you should download first. Some are paid and some are free. Have fun!
I totally recommend Racks11479's Phiremod/Honeycomb dualboot MicroSD image. It automatically boots into Phiremod (CM7 variant) but also gives you the option to boot into Honeycomb if you want to play with that and an option to boot into stock Nook Color software without taking the MicroSD out. Very nice. Also, if you're worried about stability I highly recommend getting a class 4 Sandisk card to run it off of. If you read through some of the forums this seems to be the best card for running ROMS smoothly. You can find the Phiremod/Honeycomb image here: http://forum.xda-developers.com/showthread.php?t=1045018
Good luck!
And first thing make sure you have a SanDsik microSD card.
It can be a 4/8/16 gb class 2/4 card.
There are a lot of nookers who start out with the wrong card and have a lot of problems later on, not to mention waste of money for those high class cards.
Again good luck.
Echo everything that's been said in this thread.
You have all the right answers posted to get your feet wet without worry.
If you don't want to use the (more experimental) honeycomb on the sd install, just ignore it when you boot it and it goes to the more stable phiremod version of CM7 by default.
The memory card advice is no joke. If you get a whole mess of force-close issues running the rom recommended above from an sd install, it's either a bad download, bad flash, or (90% likely) you need the right memory card.
My sig has the link to the thread if you want to know why SanDisk.
I've been a happy owner of a rooted Nook Color now for several weeks. I've played around with it and got it running the way I want and it is stable and speedy. If I wanted to pack up my current rom, clean off personal data and slap it onto a self-booting SD card, how would I do this? I've gotten a friend interested in this now and would like to generate a rom that would boot up that nook with the configuration I've setup.
Any information or pointers in the right direction would be great. I've done some research and seen existing roms that can be used for self booting but I'm hoping to find a way to put my own together.
But what you ask is the standard.
If you have ready card with rom and its inserted, it will start booting from there
Unleashed from Nook Color on Cm7 Nightly 162 @1.200Mhz
Yes I personally have a nook that boots up from a card. What I would like to do is clone what I have and put it on another card so that somebody else can boot up a nook color from it.
NapalmDawn said:
Yes I personally have a nook that boots up from a card. What I would like to do is clone what I have and put it on another card so that somebody else can boot up a nook color from it.
Click to expand...
Click to collapse
I think I get what you're shooting for. You essentially want a base image you can load onto other NCs that contains everything on your current system, minus personal info.
I don't know if you could just remove the account associated to the NC, create a backup, then load it onto another card for restoring.
Additionally, if you are using the stock OS, but rooted, I think your B&N registration information will still be attached. I don't know if you can clear this from the ROM, or if there is any device specific information associated in the ROM elsewhere.
Pretty much you want a deployable image of what you have currently, similar to deployable images companies use on PC systems.
Yes that's basically it. I'd like clone what I have, boot it up, strip out any personal data like contacts, my netflix login, etc and give the card out so that the nook can be booted up. I'll try the method of backing up the rom, moving the back up to the new SD card and doing a restore.
The OS isn't a stock one. It was previously phiremod that I changed over to CM7 build 150.
New here, yes I did look around. Found lots of other good info, but not this. If I missed it, feel free to remove my man card. I just got a nook color for x-mas yay me. I have followed two guides:
Well I tried to post two links but that wont work. I understand. Anyway, one guide is called How to Install CyanogenMod 7 on the Nook Color (PC Version), found it on Youtube. Other is called How to: Root a Nook Color, install CyanogenMod 7, and overclock it off of icrontic.com Hope that helps.
I am using at 8gb version to write to SD card. I copy both files over without un-ziping them. Follow all directions. However nook will not boot into Cyanogen. I just get the normal nook boot up. I have tried several times. I am new to the whole rooting thing and have seen people post different versions of the same file. Not sure if that has anything to do with it.
Lastly,
Nook firmware: 1.3
Not using a Scan Disk SD card.
I assume you want to enjoy the beauty of CM7.
Before guiding you, a very first basic question needs to be asked: do you want/intend to run CM7 on eMMC or off the uSD?
I assume you want to enjoy the beauty of CM7.
Before guiding you, a very first basic question needs to be asked: do you want/intend to run CM7 on eMMC or off the uSD?
Well I didn't know there were other options other than CM7. I have also been told that is one is the best all around one out there. You will have to excuse my ignorance but what is eMMC and uSD?
Don't worry, we all learn something day to day.
CM7 is a custom ROM (or OS if you want to call it), which replaced the stock OS by many of us. It is one of the most used ROM out there for NC (short cut for NOOKcolor)
In order to run/use CM7 on the NC, there are 2 choices:
1. Installing and running it (CM7) from the internal memory (a.k.a. eMMC) or
2. Booting and running it (CM7) from the external uSD card
You can spend the whole day searching for the difference in details, here, I just give you some quick thinking of the 2.
Running from eMMC = more complicate installation process, smooth performance, a lot less FC's (Force Close = applications hung), easy to backup, more storage. But you will void the B&N warranty since you delete their original stock OS.
Booting off uSD is a quick way to explore the beauty of CM7 or any custom ROM WITHOUT effecting the stock OS, meaning still under warranty. Down side is you need to have a 8GB or 16GB Sandisk class 4, which probably costs about $20 (onsale for 16GB).
Ok does it have to be a Scandisk sd card? I thought loading CM7 via SD card removed the warranty also. A side question I have. I saw on youtube someone was able to "dual boot" the nook OS with the CM7 OS. They could swap back and forth, any idea what this is about? Sorry I don't have much more information on it than that.
If loading through SD card does not void warranty I would prefer that for the time being until I get the hang of this stuff more. Then again a fully rooted nook is basically a android tablet+nook. The only reason I would want the warranty is if something inside were to break.
Would the reason why my attempt didn't work be related to the fact that I didn't have a Scandisk SD card?
K9Shep said:
Ok does it have to be a Scandisk sd card?
Click to expand...
Click to collapse
No, it does not have to be a Sandisk but Sandisk (class 4) is the best (have been tested) on the market. You can use any other brands, it might work and might not. Therefore, if you intend to run CM7 off uSD, Sandisk is strongly RECOMMENDED. If you use the uSD as an additional storage, any brand is OK.
I thought loading CM7 via SD card removed the warranty also.
Click to expand...
Click to collapse
No, it does not. Running off uSD has zero effect on stock OS.
A side question I have. I saw on youtube someone was able to "dual boot" the nook OS with the CM7 OS. They could swap back and forth, any idea what this is about? Sorry I don't have much more information on it than that.
Click to expand...
Click to collapse
A lot of people mistype or mis-use the term "dual-boot"
AFAIK, there is 2 kinds of "dual-boot" (one of them is incorrectedly used)
a. Leaving stock OS on eMMC and booting CM7 off uSD.
b. Installing 2 different ROMs on eMMC.
I personally choose to say b. should be called "dual-boot", not a. but a lot of people calling a. as "dual-boot". I don't mind.
What your question is for item a.
All you have to do is during powering up, press and hold the "N" button then select booting Normal, it will boot into whatever on the eMMC (i.e. stock OS) even having CM7 uSD plugged in.
If loading through SD card does not void warranty I would prefer that for the time being until I get the hang of this stuff more. Then again a fully rooted nook is basically a android tablet+nook. The only reason I would want the warranty is if something inside were to break.
Click to expand...
Click to collapse
A very good choice. Go for it.
Note: recommend getting the Sandisk class 4.
Would the reason why my attempt didn't work be related to the fact that I didn't have a Scandisk SD card?
Click to expand...
Click to collapse
I don't know what you're doing so can't say.
What have you done?
Ok sorry it took me a little bit to get back to you guys. I work the night shift so it can be a pain and make you seem like a ghost.
So I downloaded a file called 8gb_clockwork-0.7. Used a program called Win32 Diskmanager to write that file to the SD card. I have an 8gb SD card. Not Scandisk.
I then copied over two file that are .zip files. I did not un-zip them. Files are gapps-gb-20110307-signed and update-cm-7.0.3-encore-signed.
I am using my phone as a micro SD card reader. Could that be causing issues?
Everything I read said to do what I just said/did. I then pop in the SD card into the nook. My nook then boots up normally, I.E. standard nook OS.
Any help would be greatly appreciated, thank you.
Again, it goes back to my question in post #2.
Before getting an answer from you, I cannot provide any more help.
In fact, I don't want to guide you through the wrong direction.
I would like to run it off of the USB drive until I get familiar with it. Just in case I do not like it. As this is my first time rooting something I would like to keep my options open.
K9Shep said:
I would like to run it off of the USB drive until I get familiar with it. Just in case I do not like it. As this is my first time rooting something I would like to keep my options open.
Click to expand...
Click to collapse
I assume you meant to run CM7 off uSD (you said USB drive???)
Anyway, if that's the case, what you have done was incorrect.
Forget about it, start over again.
With your not Sandisk uSD card, I wouldn't recommend but if you have to use it, then go with it for now.
1. download "win32diskimager" (I hope you already it)
2. download the "Size-agnostic SD" v1.3 imager from this link: http://forum.xda-developers.com/showthread.php?t=1000957
3. try this ROM (build 12122011) as many others like it from this link: http://forum.xda-developers.com/showthread.php?t=1344873
4. download this GApp (20110828) for CM7 from this link: http://wiki.cyanogenmod.com/index.php?title=Latest_Version
5. try to follow verygreen's instructions from the link that I posted in step 2.
If you not able to or hitting issue, get back here for more help
Will do. Thanks again for all the help. Also yes I did mean uSD :/ I will try this Wednesday during the day and get back to you as I am about to start another shift.
Hi,
I just bought a nook color. I'm trying to install nightly cm9 on it. i have been reading and i have some questions .. please help i don't wanna turn my new nook into paperweight lol. I understand i need to make a bootable sd card with CWR on it. i understand there are newer version CWR out there now but I am only able to find 4gb version of 3.0.2.8. Will that cause a problem ? Do i have to use 4gb version CWR? I can find 1gb CWM 3.2.0.1 ( i have a 4g micro sd card ). About wiping, i know with android phones you always wipe before you flash roms but i have been reading, posts suggest to wipe cach and dalvik AFTER flashing cm and gapps. Is that the correct order to wipe? [GUIDE] Install CM7 or CM9(!) + Clockworkmod to EMMC - ALL NOOKS! (Updated:1/16/12) - xda-developers This post don't even mention wiping dalvik. So what exactly should i wipe and in what order? Also in that post it says after you flash, without rebooting you are to remove sd card and format it on a computer... since its a bootable CRW, the nook color doesnt even have the recovery on it , will removing the sd just cause it to crush ? Please help ~ Thank you.
Best advice is to go to the "development forum" and read the CM9/ICS nightly thread.Everything you need is in the first post.I would suggest you test your SD card with CrystalDiskMark 3.0(free program,google it up)first to see if it is suitable for a ROM install.
See the SD card strange thread in this forum first.
Don't worry too much about bricking your Nook Color. It is pretty much impossible to get it in a state which you can't recover from as it has priority on booting from the SD card.
That's not say you shouldn't try to get it right to avoid any hassle.
For an internal install use the Eyeballer SD clockwork recovery method as detailed in the development forum. When you image this to an SD then you always end up with a 1GB partition on the card irrespective of the real SD size. Don't worry about that as this is just a staging post and you just need space to put on the zips you want to install.
For CM9 use the "unofficial" nightly builds and put the main ROM, Gapps, and the telephony permissions fix on.
When you boot from this card you will be in Clockwork recovery. First time you want to format system, data, and cache then install ROM, Gapps and telephony fix in that order.
After that you want to put in a cleanly formatted single partition SD card, either by reformatting partitioning the installation one or a different one if you wanted to keep the original. It won't crash but some apps expect the Sd card to be present.
Once rebooted then you should be in CM9. You can install clockwork recovery to the internal memory as well by using the ROM Manager app. This means that if you reboot with the N key held down you get into a boot menu and can choose to go into recovery. That is very convenient for subsequent updates as you can just copy zips onto the SD card via USB or Wifi without having to remove the card (ES File Explorr app helps a lot here).
For small updates you can normally just format system and cache then reapply the set of zips. This will leave your set up and installed apps alone. You don't need to do Dalvik separately as it is in the cache partition.
Thanks and what is the "telephony permission fix" ?
bobtidey said:
Don't worry too much about bricking your Nook Color. It is pretty much impossible to get it in a state which you can't recover from as it has priority on booting from the SD card.
That's not say you shouldn't try to get it right to avoid any hassle.
For an internal install use the Eyeballer SD clockwork recovery method as detailed in the development forum. When you image this to an SD then you always end up with a 1GB partition on the card irrespective of the real SD size. Don't worry about that as this is just a staging post and you just need space to put on the zips you want to install.
For CM9 use the "unofficial" nightly builds and put the main ROM, Gapps, and the telephony permissions fix on.
When you boot from this card you will be in Clockwork recovery. First time you want to format system, data, and cache then install ROM, Gapps and telephony fix in that order.
After that you want to put in a cleanly formatted single partition SD card, either by reformatting partitioning the installation one or a different one if you wanted to keep the original. It won't crash but some apps expect the Sd card to be present.
Once rebooted then you should be in CM9. You can install clockwork recovery to the internal memory as well by using the ROM Manager app. This means that if you reboot with the N key held down you get into a boot menu and can choose to go into recovery. That is very convenient for subsequent updates as you can just copy zips onto the SD card via USB or Wifi without having to remove the card (ES File Explorr app helps a lot here).
For small updates you can normally just format system and cache then reapply the set of zips. This will leave your set up and installed apps alone. You don't need to do Dalvik separately as it is in the cache partition.
Click to expand...
Click to collapse
Found the telephony fix thanks
A bit of unsolicited advice: if you are having these kinds of problems, then I suggest CM9 is not baked enough for you, and you may be much better off with a far more stable and better-documented CM7.x install. I am not being condescending... I myself am quite capable of extreme hacking and tolerant of an array of stability issues, being a Linux software engineer, but I just don't have the time or energy to put into making CM9 work right now, given the quantity of issues. For the hardcore Android hobbyist, CM9 is the way to go right now. For a NC user wanting a functional Android tablet, I say wait a little bit.
You might consider simply using the SD card boot ROM's, and leaving the internal Nook alone for the present. That would allow you to try out the various Rom's available and find one that works best for you. I'm currently running CM7.2 Kang on my emmc partition, but booting on SD card from the CM9 nightly builds. The CM7.2 Kang is quite stable, but not as much fun as the alpha ICS CM9 stuff. Best of both worlds.
I already have cm7 on my phone , hopefully its not gonna be the same thing lol . i was hoping to put cm9 on there so it will entertain me for a while but if its really that buggy mb i will consider just running on cm7.
mr72 said:
A bit of unsolicited advice: if you are having these kinds of problems, then I suggest CM9 is not baked enough for you, and you may be much better off with a far more stable and better-documented CM7.x install. I am not being condescending... I myself am quite capable of extreme hacking and tolerant of an array of stability issues, being a Linux software engineer, but I just don't have the time or energy to put into making CM9 work right now, given the quantity of issues. For the hardcore Android hobbyist, CM9 is the way to go right now. For a NC user wanting a functional Android tablet, I say wait a little bit.
Click to expand...
Click to collapse
Thanks. I already have bobzhome 7.2 on my phone. The reason why i wanna cm* on my nook is because i don't read(i read enough for school XD ) haha so the nook factory rom will be kinda pointless for me. Also just booting from sd and flashing roms seem really straight forward to me so that's why i want to flash cm* on internal memory. As im not that knowledgeble about nook colors, running on a bootable rom still seem complicated for me but i sure will think about it .
brentb636 said:
You might consider simply using the SD card boot ROM's, and leaving the internal Nook alone for the present. That would allow you to try out the various Rom's available and find one that works best for you. I'm currently running CM7.2 Kang on my emmc partition, but booting on SD card from the CM9 nightly builds. The CM7.2 Kang is quite stable, but not as much fun as the alpha ICS CM9 stuff. Best of both worlds.
Click to expand...
Click to collapse
when i was downloading cm7 roms , my anti virus kept saying there were viruses in the roms ... is that normal ?
optimusv45 said:
when i was downloading cm7 roms , my anti virus kept saying there were viruses in the roms ... is that normal ?
Click to expand...
Click to collapse
How many places you going to ask this?
It is a false positive.
Normal? No. Crappy antivirus? Yes.
As long as you are downloading from links from the developers here you're safe.
Sent from my NookColor using XDA App
just making sure since im not very knowledge about nook colors. i rather ask more than do something stupid on my device and cause myself problems.
Benzoman said:
How many places you going to ask this?
It is a false positive.
Normal? No. Crappy antivirus? Yes.
As long as you are downloading from links from the developers here you're safe.
Sent from my NookColor using XDA App
Click to expand...
Click to collapse
No problem. Just noticed it was in a separate thread already.
Please post what A/V you are talking about so others having the same issue will take note.
I'll also give a +1 to the people who suggested that you work off an SD card until you are really comfortable with the process. You can always recover your Nook, but why go through that hassle when the SD card is so easy.
Just my $.02
Dual booting SD
I agree with try the Dual boot off the SD card to see what you like. Check out http://forum.xda-developers.com/showthread.php?t=1000957Verygreens process was simple to follow and I am newer at rooting also. Cheers.
I posted what a/v already. its kaspersky internet security. i guess i never look into running off SD. I don't read much so i just don't need nook color stock ROM, i guess that's also part of why i wanna run on internal memory. oh and i bought a refurbished nook color from BNs website and it came defective. part of the screen didn't work. To those who wanna buy it from them i suggest to buy from a retail store so u don't have to pay shipping and waste time I think all they did was a factory restore on a return and sell it again for 149.
TL2000 said:
Please post what A/V you are talking about so others having the same issue will take note.
I'll also give a +1 to the people who suggested that you work off an SD card until you are really comfortable with the process. You can always recover your Nook, but why go through that hassle when the SD card is so easy.
Just my $.02
Click to expand...
Click to collapse
Im gonna buy a new nook color and i read that newer ones have different hardware. newer hardware aren't supported by CM7. I guess I'll have to try a nightly CM9 build.
The1Power said:
I agree with try the Dual boot off the SD card to see what you like. Check out http://forum.xda-developers.com/showthread.php?t=1000957Verygreens process was simple to follow and I am newer at rooting also. Cheers.
Click to expand...
Click to collapse
will CM7 work on a new nook color? i have read that it doesn't have some needed drivers.
mr72 said:
A bit of unsolicited advice: if you are having these kinds of problems, then I suggest CM9 is not baked enough for you, and you may be much better off with a far more stable and better-documented CM7.x install. I am not being condescending... I myself am quite capable of extreme hacking and tolerant of an array of stability issues, being a Linux software engineer, but I just don't have the time or energy to put into making CM9 work right now, given the quantity of issues. For the hardcore Android hobbyist, CM9 is the way to go right now. For a NC user wanting a functional Android tablet, I say wait a little bit.
Click to expand...
Click to collapse
optimusv45 said:
will CM7 work on a new nook color? i have read that it doesn't have some needed drivers.
Click to expand...
Click to collapse
I just bought my nook color Dec. 30th, 2011 and I have ran cm7 as well as cm9. Like the others are saying, set up cm7 off of a SD card until you learn what you are doing then consider moving to the emmc.
optimusv45 said:
will CM7 work on a new nook color? i have read that it doesn't have some needed drivers.
Click to expand...
Click to collapse
I believe that is CM9, not 7 that was having issues with the new nook color touch screen drivers.
Here's a post about it:http://forum.xda-developers.com/showthread.php?p=21333209&highlight=touchscreen#post21333209
Looks like it may already be fixed: http://forum.xda-developers.com/showthread.php?p=21353661&highlight=touchscreen#post21353661