Carrier shjowing numbers - Vibrant General

Carrier is just showing numbers on a AOSP rom I installed. I understand this is completely stripped but I was wondering how to setup the carrier name properly instead. I read that spn-conf.xml in /system/etc/ is what I should edit but there was no file so I created one and pushed it to the device with adb rebooted the device but no luck. Anyone know how to set this up? Thanks

maybe you lost the imei?

No phone works fine.. I know there is suppose to be a file that will read the numbers then display the carrier name. Before it use to be spn-conf.xml and you would setup the file as follows;
<spnOverride
numeric="302320" spn="Mobilicity"/>
</spnOverrides>
then push it to /system/etc and it would overwrite the file however in the new 2.3.5 this file is not present and was wondering if anyone with knowledge knows this. I would post in development but that is for projects and not for troubleshooting or chatting.
Thanks

Did you find a fix for this? I just installed CyanogenMOD 7.1 and am seeing these numbers as well (using Mobilicity on my Vibrant).

Related

[DEV][20.11.2011] Android Gingerbread SIP over 3g for (probably) every GB based rom

Here is a bit of why I wrote this manual:
Back at December 2010 Paul from modaco found how to enable sip over 3g for the gingerbread native client, his original thread is here:
http://android.modaco.com/topic/327770-using-gingerbread-internet-calling-sip-without-wifi/
For chefs it is probably straight forward how to use this tip, but for me I always begged for cookers to include this in their roms usually they didn't even replay to my request, so I investigated this, and here is very easy way to enable this feature.
This guide assumes you are a little familiar with changing files on your ROM.
*I take no responsibility for this guide, use it at your own risk
So, what we are doing is modifying the framework-res.apk from from our framework directory.
We need:
apktools from here: http://code.google.com/p/android-apktool/
Two files are needed, this: http://code.google.com/p/android-apktool/downloads/detail?name=apktool1.4.1.tar.bz2&can=2&q=
And this: http://code.google.com/p/android-apktool/downloads/detail?name=apktool-install-windows-r04-brut1.tar.bz2&can=2&q=
(You can also do this for Linux and Mac, this guide will use windows)
Take the framework-res.apk from your ROMS zip file inside /system/framework directory.
How its done:
Extract both files that you downloaded to c:\apktools (can be any dir...)
You should have 3 files.
Copy the framework-res.apk to the same directory: c:\apktools
start --> run --> cmd
c:
cd \apktools
apktools d framework-res.apk temp
Now a folder named temp will appear named temp
inside temp, edit the file: C:\apktools\temp\res\values\bools.xml
I use notepad++, search for a line:
<bool name="config_sip_wifi_only">true</bool>th
change in the line the "true" into "false"
save the file.
go back to cmd
c:
cd \apktools
apktools b temp temp.apk
Now rename your original framework-res.apk to framework-res.apk.zip
open it with winrar/winzip/7zip it will open like regular archive.
take the file that was created by the build process:
C:\apktools\temp\build\apk\resources.arsc
Use this file to replace the file inside the archive of framerwork-res.apk.zip (overwriting the original, inside the zip)
rename the file back to framework-res.apk
And now you have a sip over 3g enabled framework-res.apk.
There are few options to push this file, easiest is just replace it in your ROM zip and flush the ROM, you need to wipe cache and dalvik cache.
There are other ways to push this to your rom but I won't discuss them here.
I used this on stock roms, AOSP roms, MIUI roms and Sense roms, worked for me on all, if you find a roms it doesn't work on please report.
Thats it, its actually quite easy.
You are Awesome! Thank you for posting this. I just setup my phone with this and it works great.
Great Process, a few little remarks
Shalom,
This is a great process tutorial and within 15 minutes I flashed my HTC Sensation to support Internet calls on 3G/4G, while before it was WiFi ONLY.
So now, no need to have any cellular minutes purchased, have DATA have LIFE.
Remarks:
1. Have only 2 files. You mentioned 1 download and then 2 more. The 1st is duplicated withing the 2.
2. The BAT file is apktool.bat and not apktools.bat.
Other then that, SWEEET.
Toda Raba.
Easy
---------- Post added at 04:29 AM ---------- Previous post was at 04:11 AM ----------
HTC Sensation T-Mobile.
Forgot to mention earlier.
Thanks.
HI
tryed not working stoped at temp file cretion is showing an eror cant go further plz help
Does this change your phone to use 3g to make calls? If so that is excellent.
Sent from my Sabotaged Droid Incredible 2.
Thanks, but why don't we use SIP third-party such as Sipdroid, 3CXPhone...? I think they are easy to use.
Nice work , What about Xperia Lines, will there appear 3G video calling button ?
I tried on Wet Dreams 1.3.0 for Atrig 4G and didn't works (Didn't show SIP Calling option)... maybe my mistake or isn't working with Moto's 2.3.6 build. But I asked to be added by the chef! Thanks for this tip!
If SIP options are not present in your Settings.APK it may have been disabled by the carrier.
The solution is to place the proper permissions file into /system/etc/permissions/ which will enable SIP overall on your device, then of course to this fix as well.
Solution found in various other places, just thought I'd add it to this thread since the thread is linked from the homepage.
Nice, surprisingly easy, almost to much so lol
lotherius said:
If SIP options are not present in your Settings.APK it may have been disabled by the carrier.
The solution is to place the proper permissions file into /system/etc/permissions/ which will enable SIP overall on your device, then of course to this fix as well.
Solution found in various other places, just thought I'd add it to this thread since the thread is linked from the homepage.
Click to expand...
Click to collapse
Thanx.
But it didnt work for me, and still not seeing sip settings.
I plased the attached file in system/etc/permissions, rebooted.
Also tried to fix permissions, and still didnt work.
Please Help
Verizon Motorola Droid 3
Stock deodexed Rom, Android 2.3.4
BTLINU said:
Thanx.
But it didnt work for me, and still not seeing sip settings.
I plased the attached file in system/etc/permissions, rebooted.
Also tried to fix permissions, and still didnt work.
Please Help
Verizon Motorola Droid 3
Stock deodexed Rom, Android 2.3.4
Click to expand...
Click to collapse
Then the options probably just aren't there in your carrier's Rom. They were present in my LG Rom, after I pushed the permissions file. However, when I tried to use SIP, it would force close as soon as the call connected... something else missing.
In my case and yours, the answer is to use SipDroid from the market.
Pls any guide on how to do this in ICC ROMs

[GUIDE]How to change your region.

Always make a backup before changing / on your device!
Q. What is this?
A. A way to change your region. More manufacturers in QRemote, Russian/Greek/etc T9 in dialer, working 4G, no wifi frequency restrictions and more.
Q. Will it get me OTA's of the region i changed to?
A. No.
Q. Is there any easier method, one that does not require root, perhaps?
A. I don't know one.
Boring technical details:
Latest firmwares do not "belong" to region. Instead, they adapt to phone's own region. The check is done at each boot, settings are applied after build.prop.
The detection uses combination of operator code and country code (2 bytes, numbering convention unknown. In LG's documents it's referred to as "BUYER").
LG determines phone's region by looking into the "misc" partition, at addresses 0000A000-0000A020.
Information at them looks like this:
Code:
"1","FFF,FFF,FFFFFFFF,FFFFFFFF,12"
, where "12" is country code.
We can change it ourselves by using hex editor on a dumped image.
The regional parameters reside in /cust/ folder. The file "/cust/cust_path_mapping.cfg" maps "{operator_code},{country_code}" to a folder where it's parameters reside.
Note: some countries (FRA, for example) or some operators don't have their own folder in /cust/. They use 11 (OPEN_EU) as NT code, and identify themselves based on some other info I've yet to find.
Example of cust_path_mapping.cfg content:
Code:
20810,FF=/cust/VDF_COM/FR
20810,01=/cust/VDF_COM/LPM
Explanation: Vodafone in any country but 01 will use "/cust/VDF_COM/FR", while Vodafone in "01" country will use "/cust/VDF_COM/LPM". Notice theirs relative positions. This means that only the most exact match is used, and creating "FFFFFF,FF=/cust/XDA" key won't point the phone towards XDA folder.
By changing this file - or changing the contents of the folder your "operator,country" combo is pointing to - you can change your phone's region to anything you want.
There is also a "/cust/cust.prop" file. It contains fallback to defaults, if phone was unable to determine needed folder, or it didn't exist, it uses "/cust/SUPERSET/".
! In 5.0 firmwares, annoying message stating that "current version not avaliable for user" shows up if the above happens.
The folders in /cust/ hold operator/country settings. LG named them this way: "OPERATOR_COUNTRY". There are 2 special values - OPEN for operator - which means any operator, COM for country - which means any country.
OPEN_XXX hold parameters for specific country. These folders may contain subfolders with parameters for smaller operators which operate only inside this country.
Example: OPEN_ZA, which contains folders for MTN and VDC operators.
XXX_COM contain parameters for specific operator. These folders may contain subfolders with parameters for specific countries.
Example: /VDF_COM is intended for Vodafone. It contains folders FR and LPM, which are intended for France and LPM (?).
{OPERATOR_COUNTRY} folders are intended for 1 combination of operator and country, they should not contain subfolders with settings for other operators/countries.
Example: PCL_IL, contains settings for one of Israel operators.
The method itself:
1) Install Busybox.
1) Look at /cust/cust_path_mapping.cfg and choose some region's code. The folder names are usually self-explanatory, and you can always look into /cust/{folder}/cust.prop to see to what ro.build.target_operator, ro.build.target_country and ro.build.target_region variables are set.
2) Execute the below code, replacing "\x31\x32" in "echo -n '\x31\x32'" with your chosen code. Examples: "\x35\x36" is 56 region, "\x37\x33" is 73 region and so on.
First line backs up your "misc" partition to /sdcard/misc.bin, you should copy this file to safe storage.
Code:
dd if=/dev/block/platform/msm_sdcc.1/by-name/misc of=/sdcard/misc.bin
echo -n '\x31\x32' | /system/xbin/dd of=/dev/block/platform/msm_sdcc.1/by-name/misc bs=1 seek=40991 count=2 conv=notrunc
reboot
Why did i use busybox's dd? Because in LG's 5.0 default dd was compiled without conv option...
Enjoy your new region!
Other methods:
Method 1: substitution.
Step 1: Find out which country your phone was meant to use ("Settings->About Phone-> Software" ). Find your current operator code. Using these, find currently used folder in /cust/. You can get to know folder's region by looking on it's name, or opening the {folder}/cust.prop file and looking at these keys:
Code:
ro.build.target_operator
ro.build.target_country
ro.build.target_region
They are pretty self-explanatory.
Step 2: Replace the folder's content with content from the region you want to change to.
Step 3: Reboot and be happy!
Method 2: via editing "misc" partition.
Be extra careful with "misc". This partition is unique for every phone. If it's damaged or wiped, things may get ugly.
I do not know a way of regenerating "misc", since it contains your bluetooth/wifi mac's and IMEI. AFAIK, It is only used for displaying that info in Android and for LG's updates - so you won't lose bluetooth/wifi/mobile data, but still...
Since it's also used for updates, PC suite and "ota updater" won't be able to update your phone anymore if this partition is damaged.
It may also have uses which we don't know about. Make a backup, save it to several clouds and 2-3 offline storages.
Do not proceed if you don't know what "hex editor", "backup" and "partition dump" are.
1) Grab misc with "dd if=/dev/block/platform/msm_sdcc.1/by-name/misc of=/sdcard/misc.bin".
2) Open misc.bin in any hex editor, go to address "0000A000" and look for this:
Code:
"1","FFF,FFF,FFFFFFFF,FFFFFFFF,12"
Change "12" or whatever number you have there to the one that you need. You can look into cust_path_mapping.cfg to determine it. Save the result to a new file, name it "misc_edited.bin".
3) Replace your misc with edited one: "dd if=/sdcard/misc_edited.bin of=/dev/block/platform/msm_sdcc.1/by-name/misc".
4) Reboot.
I have no idea about how PC suite and others will react to IMEI and country code mismatch. They probably won't care, but we don't know it for sure.
Method 3:
Warning, in 5.0 this will cause the annoying "Current version not avaliable for user!" message to show up at each boot.
1) Backup your rom and /cust/ folder.
2) In /cust/cust_path_mapping.cfg delete all lines except
Code:
999999,99=/cust/SUPERSET
.
3) Copy everything from /cust/{Your_desired_region} to /cust/SUPERSET.
4) Reboot.
Big thanks to my Russian comrades rxu, KestL and Beerukoff for pointing out important details!
Reserved.
Hi, thanks very much for this write up. I'm still a bit confused as to how to actually do this - and I'm thinking others might be as well since there haven't been any responses. Would you mind walking me through how to change the region for a phone purchased in HK? I would like to change it to the EUR region.
Would I open the cust.prop file within the HK folder and change the values for the three variables above to match the ones found in the cust.prop file within the EU folder?
Thanks.
Japultra said:
Hi, thanks very much for this write up. I'm still a bit confused as to how to actually do this - and I'm thinking others might be as well since there haven't been any responses. Would you mind walking me through how to change the region for a phone purchased in HK? I would like to change it to the EUR region.
Would I open the cust.prop file within the HK folder and change the values for the three variables above to match the ones found in the cust.prop file within the EU folder?
Thanks.
Click to expand...
Click to collapse
It would be better to change /cust/cust_path_mapping.cfg file. Open it, find the line "FFFFFF,54=/cust/OPEN_HK", change it to "FFFFFF,54=/cust/OPEN_EU" and reboot.
I'm using a custom based off a version that doesn't have my cust (SEA) so mine reverts to the default. I'm in the uk.
Other than having to delete the ltesettings apk I haven't noticed any problems. Do you think I would notice anything if I change the mapping to point at EU it would improve anything?
Nice write-up, very detailed. This seems very specific, do you know why you would want to do this? A scenario maybe?
YaDr said:
It would be better to change /cust/cust_path_mapping.cfg file. Open it, find the line "FFFFFF,54=/cust/OPEN_HK", change it to "FFFFFF,54=/cust/OPEN_EU" and reboot.
Click to expand...
Click to collapse
Thanks! That worked.
oracleoftruth said:
I'm using a custom based off a version that doesn't have my cust (SEA) so mine reverts to the default. I'm in the uk.
Other than having to delete the ltesettings apk I haven't noticed any problems. Do you think I would notice anything if I change the mapping to point at EU it would improve anything?
Click to expand...
Click to collapse
No, i don't think that you'll notice anything. You'll get more manufacturers in qremote and other very minor features.
sprremix said:
Nice write-up, very detailed. This seems very specific, do you know why you would want to do this? A scenario maybe?
Click to expand...
Click to collapse
Thanks!
Why you may want to change region:
1) QRemote contains a lot more manufacturers if ro.build.target_region is set to ESA. Since /cust/ is applied after build.prop, you'll have to edit it.
For example, in CIS region Western Digital is absent. It is officially sold here in Russia, there is no embargo or whatever. LG just decided that Russians doesn't have the right to control "WD TV live" using QRemote. Nice.
2) Dialer - there are special dialer overlays with letters used in specific regions. For CIS it contains cyrillic letters, for Greece it contains Greek letters, and so on.
3) Featureset.xml also depends on region. It contains miscellaneous settings, like the ability to send empty sms.
4) There are a lot more overlays for other apps. Voicemate, etc. Nothing major, but this can change in future.
P.S. I updated first post with info about misc partition.
Thanks @YaDr
Just changed the V10M Hong kong to EUR-XX.
One question: do i need to manually change/fix all the new files permissions?
robalm said:
Thanks @YaDr
Just changed the V10M Hong kong to EUR-XX.
One question: do i need to manually change/fix all the new files permissions?
Click to expand...
Click to collapse
No, until files have been exposed to non-posix filesystem and lost their permissions, or you've changed them manually.
Default permissions for /cust/ are 755 with root/root as owner/group.
YaDr said:
No, until files have been exposed to non-posix filesystem and lost their permissions, or you've changed them manually.
Default permissions for /cust/ are 755 with root/root as owner/group.
Click to expand...
Click to collapse
Ok.
In /cust/SUPERSET There is already a "cust.prop" file should i replace that one with the cust.prop from my OPEN_XX folder?
Is there a risk to loose/get blocked IMEI in this way we change region?
robalm said:
Ok.
In /cust/SUPERSET There is already a "cust.prop" file should i replace that one with the cust.prop from my OPEN_XX folder?
Is there a risk to loose/get blocked IMEI in this way we change region?
Click to expand...
Click to collapse
Yes, you should replace it.
It is highly unlikely that you will lose IMEI. However, i ask everyone to make a full nandroid backup, efs included, before you do anything to your phone.
As for the blocking... Why would your service provider care enough to blacklist your IMEI? Unless it is forbidden by local laws or service contract, manipulating files on your phone is perfectly legal.
YaDr said:
Yes, you should replace it.
It is highly unlikely that you will lose IMEI. However, i ask everyone to make a full nandroid backup, efs included, before you do anything to your phone.
As for the blocking... Why would your service provider care enough to blacklist your IMEI? Unless it is forbidden by local laws or service contract, manipulating files on your phone is perfectly legal.
Click to expand...
Click to collapse
Thanks bud.
I have a efs backup, but no nandroid backup.
YaDr said:
It would be better to change /cust/cust_path_mapping.cfg file. Open it, find the line "FFFFFF,54=/cust/OPEN_HK", change it to "FFFFFF,54=/cust/OPEN_EU" and reboot.
Click to expand...
Click to collapse
Hi
Need to erase all the rest lines or only change those 2?
Thank you
alexa74 said:
Hi
Need to erase all the rest lines or only change those 2?
Thank you
Click to expand...
Click to collapse
You only need to change 1 line. Nothing has to be deleted.
Did anybody tried if this works on the Korean models (F400S/L/K)?
YaDr said:
You only need to change 1 line. Nothing has to be deleted.
Click to expand...
Click to collapse
Hi
Thanks, it was helpfully,but may be you can help me to change the region to Israel?
alexa74 said:
Hi
Thanks, it was helpfully,but may be you can help me to change the region to Israel?
Click to expand...
Click to collapse
What's your current region?
YaDr said:
What's your current region?
Click to expand...
Click to collapse
Was HKG and now is EU
alexa74 said:
Was HKG and now is EU
Click to expand...
Click to collapse
in /cust/cust_path_mapping.cfg find a line ending with "OPEN_EU", and change folder name from "OPEN_EU" to "PCL_IL" or "ORI_IL". If you don't have these folders, i can zip them and send them to you.

[Q] Changing SystemUI.apk for Sprint GS4 (L720T)

I am trying to change Sprint GS4 L720T 3g data indicator to a 4G data indicator, so whenever I connect to HSPA, I get the 4G icon instead of the 3G icon. I have identified the icon inside the SystemUI.apk file: it's called "stat_sys_data_connected_3g_spr.png." My idea is to change that icon with another one like "stat_sys_data_connected_4g_att.png" or "stat_sys_data_connected_4g_tmo.png".
Method 1: I used 7-zip to inter-change the name of the files within the apk and then moved back to modified file to /system/priv-app/
Method 2: I used apktool to rename the file name and the moved the re-compiled apk back to /system/priv-app/
The problem: With both method the device seems to detect the changes I made thru signature detection or some other method and the modified SystemUI.apk does'n't work.
I have even tried a de-odexed ROM and tried both previous method and the device keeps failing to recognize the apk.
Does anyone has any idea on how can I change SystemUI.apk without triggering the signature change?
PS: I was able to do this but only on a device that had a 15 digit EMEI instead of the 14 digit MEID. I cannot reproduce the problem again because I don't have any other device with a 14 digit MEID.
Can anyone at least lead me in the right direction?
Extract the pngs you want to use, rename them to the ones you want to replace, put back into apk
Profit
Or decompile/recompile properly
Or disable signature check
BTW, this isn't really relevant to the developer section

[Quick Guide] - Enabling Hidden Features

Just wanted to share a few CSC features that are tested to work on the S6/S6 edge.
This is not my work, just sharing.
To enable these you will need root, a root explorer and text editor.
Simply navigate to system/csc/Features.xml and add the corresponding line to the end of the file but before the very last few lines that say </feature> and </Samsung>
(if this file does not exist, create the csc folder in system and a txt file within it then change the name to features.xml and add the correct lines and save) if this does not work you can try the same method with Others.XML in the same folder
*Make sure you make backups of the stock files in case there are issues.*
Enable WiFi calling in phone settings:
Code:
<CscFeature_Setting_SupportWifiCall>TRUE</CscFeature_Setting_SupportWifiCall>
Enable native voice call recording(maybe illegal is some countries):
Code:
<CscFeature_VoiceCall_ConfigRecording>RecordingAllowed</CscFeature_VoiceCall_ConfigRecording>
Enable shutter sound switch in camera settings(maybe illegal is some countries):
Code:
<CscFeature_Camera_ShutterSoundMenu>true</CscFeature_Camera_ShutterSoundMenu>
Enable camera during call:
Code:
<CscFeature_Camera_EnableCameraDuringCall></CscFeature_Camera_EnableCameraDuringCall>
Enable manual rotation option in gallery:
Code:
<CscFeature_Gallery_AddAutoRotationIcon>true</CscFeature_Gallery_AddAutoRotationIcon>
Continuous music while using camera:
Code:
<CscFeature_Camera_CamcorderDoNotPauseMusic></CscFeature_Camera_CamcorderDoNotPauseMusic>
Enable scheduled messaging option in messaging app:
Code:
<CscFeature_Message_EnableScheduledMessage>true</CscFeature_Message_EnableScheduledMessage>
<CscFeature_Message_EnableScheduledMsgBox>true</CscFeature_Message_EnableScheduledMsgBox>
Enable exit buttons in default browser:
Code:
<CscFeature_Web_AddOptionToTerminate>true</CscFeature_Web_AddOptionToTerminate>
Enable 2nd symbol keys on stock keyboard:
Code:
<CscFeature_Sip_UseSymbolInCMKey>true</CscFeature_Sip_UseSymbolInCMKey>
<CscFeature_Sip_EnableSymbolInSecondary>de;en_US;en_GB</CscFeature_Sip_EnableSymbolInSecondary>
Enable VoLTE Support: Thanks to IakobosJ
Code:
<CscFeature_RIL_SupportVolte>true</CscFeature_RIL_SupportVolte>
<CscFeature_IMS_EnableVoLTE>true</CscFeature_IMS_EnableVoLTE>
Remove NFC enabled icon in the status bar: Thanks to evonc
Code:
[COLOR="Red"]Delete line[/COLOR] : <CscFeature_NFC_StatusBarIconType>DEFAULT</CscFeature_NFC_StatusBarIconType>
ADDED 21/04/15
Sort app draw alphabetically:
Code:
<CscFeature_Launcher_EnableViewByAlphabetAsDefault>true</CscFeature_Launcher_EnableViewByAlphabetAsDefault>
I Hope this helps someone out,
Big Thanks to this post for the info, there are many more in the original post but these are the only ones I've tried and have worked so far,
and IakobosJ for his help in the wifi calling thread
if anything needs adding let us know and it can be added to this post,
This is dedicated to the hard working XDA community
Thank You All
Theres also some nice tools in the play store -:- Be careful when using these!
Samsung CSC Master
CSC Feature Expert
(I own google so get a big cut of the profit made on these )
I've tried CSC Feature Expert now -and it seems to work well,
Quick tut:
I would backup original CSC folder first
Just search for the option you want to enable,
Select the value ( see pic 1)
in the popup - Input the correct value (see pic 2 - label 1)
(a few examples of values)
' RecordingAllowed ' to enable call recording,
' true ' for shutter sound menu,
' true ' for launcher by alphabet,
' true ' for rotation icon in gallery,
' true ' for support wifi call,
then click save (see pic 2 - label 2)
restart you device
Hope this helps
If only we could root, without tripping Knox.
I don't want to root my phone in fear that Samsung Pay won't work with a tripped Knox.
Nice to see you've put all of this information together
For those on EE you may also want to enable VoLTE. I know it's unlikely to be in anyones area yet, but they are rolling it out across the UK (Very slowly)
Enable VoLTE Support
<CscFeature_RIL_SupportVolte>TRUE</CscFeature_RIL_SupportVolte>
Enable VoLTE
<CscFeature_IMS_EnableVoLTE>true</CscFeature_IMS_EnableVoLTE>
Just a quick note that the commands have to be added before the
</FeatureSet>
</SamsungMobileFeauture> tags at the end of the file.
Tested the Call recording and Shutter sound edits. Worked great.
Lastly if you want to remove that ugly NFC enabled icon in the status bar, delete line
<CscFeature_NFC_StatusBarIconType>DEFAULT</CscFeature_NFC_StatusBarIconType>
from the file and it will hide the icon.
evonc said:
Just a quick note that the commands have to be added before the
</FeatureSet>
</SamsungMobileFeauture> tags at the end of the file.
Tested the Call recording and Shutter sound edits. Worked great.
Lastly if you want to remove that ugly NFC enabled icon in the status bar, delete line
<CscFeature_NFC_StatusBarIconType>DEFAULT</CscFeature_NFC_StatusBarIconType>
from the file and it will hide the icon.
Click to expand...
Click to collapse
Thats strange as I've added mine after the samsung tags and all is working fine fine on my device.
Have you had problems in the past with doing that?
No. I saw the file header and noticed they're inserting commands between those tags. The original guide also has that listed but I guess it may or may not work.
Also I believe the file may get reset when you enter stock recovery so I'm assuming this should work as a fix.
1. Open the sales_code.dat to find your csc code.
2. Open the folder above with the same code.
3. Navigate to <code>/system/csc and you'll see another others.xml
4. This is most likely the file that gets applied after a factory reset/activation.
5. Make changes to this file as well.
*Make sure you make backups of the stock files in case there are issues.*
evonc said:
No. I saw the file header and noticed they're inserting commands between those tags. The original guide also has that listed but I guess it may or may not work.
Also I believe the file may get reset when you enter stock recovery so I'm assuming this should work as a fix.
1. Open the sales_code.dat to find your csc code.
2. Open the folder above with the same code.
3. Navigate to <code>/system/csc and you'll see another others.xml
4. This is most likely the file that gets applied after a factory reset/activation.
5. Make changes to this file as well.
*Make sure you make backups of the stock files in case there are issues.*
Click to expand...
Click to collapse
I would have thought it would have had to be within those tags too. Only found it didn't when i wasn't paying attention while modding it. LoL
Nice tip. Thanks. hoping there's more cool things that can enabled with this, maybe some S6 exclusives finds .
I'm on the Sprint Edge and don't have that folder. I guess I'll create and see what happens
SantinoInc said:
I'm on the Sprint Edge and don't have that folder. I guess I'll create and see what happens
Click to expand...
Click to collapse
I didnt have it either . Just create the csc folder and make a txt file and change the name to others.xml. as the op states. infact ill post a copy with basic changes i the first post.
It works fine for me. hopfully you wont have any issues
I actually did have the folder. I was looking at the folder ". System" However, after adding those lines and saving it had no effect. Can you take a look at this to see if it's right?
Edit: can't upload the xml file.
SantinoInc said:
I actually did have the folder. I was looking at the folder ". System" However, after adding those lines and saving it had no effect. Can you take a look at this to see if it's right?
Edit: can't upload the xml file.
Click to expand...
Click to collapse
You'll have to zip it before you can upload it... or rename others.xml to others.txt
I've attached a basic others.xml with all functions listed in the OP
and an original copy of the EE csc folder that IakobosJ uploaded in the WIFI calling thread
(it would be good if everybody could upload their original csc folders for reference and backups in case someone messes up theirs by accident.)
You can just copy and paste my others.xml into the bottom of your own others.xml(backup yours first)
I've had to do this as XDA's forum system seems to have changed at least one of the lines I've posted, and I've even tried going back and editing and it keeps putting a space in the middle of one of them, so use the upload if your having trouble,
I've deleted all but this file in my csc folder and tested it to make sure there nothing else it depends on - everything is working fine on my device.
But feel free to upload your for us to have a look at
im confused?
i can already do wifi calling and most of these things already without root
im on tmobile
tiboric said:
You'll have to zip it before you can upload it... or rename others.xml to others.txt
I've attached a basic others.xml with all functions listed in the OP
and an original copy of the EE csc folder that IakobosJ uploaded in the WIFI calling thread
(it would be good if everybody could upload their original csc folders for reference and backups in case someone messes up theirs by accident.)
You can just copy and paste my others.xml into the bottom of your own others.xml(backup yours first)
I've had to do this as XDA's forum system seems to have changed at least one of the lines I've posted, and I've even tried going back and editing and it keeps putting a space in the middle of one of them, so use the upload if your having trouble,
I've deleted all but this file in my csc folder and tested it to make sure there nothing else it depends on - everything is working fine on my device.
But feel free to upload your for us to have a look at
Click to expand...
Click to collapse
Ok, I'm finally on a PC so I had a chance to zip that file and have uploaded it. IDK where I screwed up. I'm rooted, I found the System/CSC/Others file and made the proper edits and then saved it. The original file was automatically backed up. The permissions were the same as the original file. IDK what I did wrong.
SantinoInc said:
Ok, I'm finally on a PC so I had a chance to zip that file and have uploaded it. IDK where I screwed up. I'm rooted, I found the System/CSC/Others file and made the proper edits and then saved it. The original file was automatically backed up. The permissions were the same as the original file. IDK what I did wrong.
Click to expand...
Click to collapse
is it just call recording and shutter sound toggle you want to add?
I want to add the NO NFC notification, CALL RECORDING, WI-FI CALLING and NO SOUND for snapping pics.
SantinoInc said:
I want to add the NO NFC notification, CALL RECORDING, WI-FI CALLING and NO SOUND for snapping pics.
Click to expand...
Click to collapse
I've uploaded two versions, one with the feature you've asked for and a full featured one, both based on your original other.xml and tested on my device to be working
just copy one to your csc folder
let me know if you have any problems
tiboric said:
I've uploaded two versions, one with the feature you've asked for and a full featured one, both based on your original other.xml and tested on my device to be working
just copy one to your csc folder
let me know if you have any problems
Click to expand...
Click to collapse
I really appreciate the effort but that didn't work either. I used the file you uploaded for me and made sure the permissions were the same and rebooted. None of the mods worked. It's really weird. I'm going to inquire in the Sprint thread to see if anyone can get these to work.
Unrelated do you know which folder I can find the boot sounds and camera sounds? I'm just going to delete them and that will solve part of my problem.
SantinoInc said:
I really appreciate the effort but that didn't work either. I used the file you uploaded for me and made sure the permissions were the same and rebooted. None of the mods worked. It's really weird. I'm going to inquire in the Sprint thread to see if anyone can get these to work.
Unrelated do you know which folder I can find the boot sounds and camera sounds? I'm just going to delete them and that will solve part of my problem.
Click to expand...
Click to collapse
Thats a shame maybe sprint have changed something.
Sure its
/system/media/audio/ui/PowerOn.ogg
Hope this helps
Killed boot sound but I must have not found the right OGG file for the camera. Do you know the name of the file?
SantinoInc said:
Killed boot sound but I must have not found the right OGG file for the camera. Do you know the name of the file?
Click to expand...
Click to collapse
I believe its
/system/media/audio/ui/camera_click.ogg
P.s did you try any of the apps posted in the second post. I dont know how well the work but ghey seem to have good reviews

Unbricked devices split screen (potential) fix - Fixed QDCM Calibration XML Files

*edit* deleted thread. Unfortunately this doesn't fix it. QFIL then flashing EUI ROM 14s and then upgrading to a newer EUI ROM or device firmware update then custom ROM is the only true fix.
Sadly, it doesn´t work for mine, maybe you can help me?
Greetings.
Iceee44 said:
Sadly, it doesn´t work for mine, maybe you can help me?
Greetings.
Click to expand...
Click to collapse
Heyyo, hmm darn that's unfortunate... Well, I have a test build of LineageOS 15.1 for the Le Max 2 with the calibration fixes in place and same with the upcoming official weekly build of LineageOS 14.1 for the X2 this Saturday. It's up to you which you would want to try. Hopefully one of them will work for you.
If not? I'm unsure what else could be causing the issue then hmm...
Hey thanks for reply!
I don't why, but something worked!
I got the splitscreen bug, then I flashed the recovery to the newest twrp (the blue one, don't know which version, but I will look it up). Then I wiped everything and install your fix. Result = bricked. Another try with one flash 2.0 and no error from flash. Fastboot recovery flash and everything was perfect.
I think it was luck, but my leeco le max 2 is repaired :victory:
Wow that's lucky! Congrats on fixing it!
May I please ask what happened to cause the brick? I've heard of device bricking but haven't seen an exact answer as to what unfortunately caused it.
It was totally my fault... I Format my data...and no image on storage... And one flash did the screen problem, maybe the program doesn't decompress a file finally... I decompressed the qfil data two times... The first time I got an error, after full decompressed everything...
Ah if you format data without any ROM on the device you can always use a PC and USB cable to do this...
adb push NameOfROM.zip /sdcard
Which will copy the zip file to the root of your data storage. Same can be repeated for Gapps or Magisk, etc.
I tried to push a 1,8GB file...
But after 2 hours it wasn't transferred, so I found the software and this is much easier.
Could you explain what exactly the "Unbricked devices split screen" bug is?
So from understanding the changes, does this mean that the 4 profiles in the Display -> Colour mode menu won't actually activate for people with the issue? (So if they do change then you don't have the bug?)
I'm guessing that editing those xml files could help with this problem? https://forum.xda-developers.com/le-max-2/how-to/le-max-2-black-crush-survey-t3744594
Or are there other places where those parameters are set?
ThE_MarD said:
Heyyo, this is a TWRP flashable zip file to replace the broken formatting on the qdcm calibration xml files for the display panels used in the LeEco Le Max 2
Click to expand...
Click to collapse
Which bug your fix is intended to fix? Do you mean this: https://youtu.be/3yXnrkfsJMI - I have never seen it on my device.
Or you mean color calibration, which is currently terrible by default (too much yellowish)
oneNight1 said:
Could you explain what exactly the "Unbricked devices split screen" bug is?
So from understanding the changes, does this mean that the 4 profiles in the Display -> Colour mode menu won't actually activate for people with the issue? (So if they do change then you don't have the bug?)
I'm guessing that editing those xml files could help with this problem? https://forum.xda-developers.com/le-max-2/how-to/le-max-2-black-crush-survey-t3744594
Or are there other places where those parameters are set?
Click to expand...
Click to collapse
For both of these questions the hopes is that the main issue with most people who unbrick their devices having screen issues is due to calibration settings being lost which this in theory should restore as it would have XML files with proper formatting unlike before where stock EUI ROM for the Le Max 2 had broken calibration XML files.
In theory if the black crush issue is also a calibration issue there's a chance this could also fix it... But still, I haven't really looked into that as I was mainly looking for a better solution for those unfortunate people suffering from unbrick device woes. If it fixes it? Cool... If not? Then I'm not too sure. Calibration files could potentially be modified to fix black crush if the issue is in there that LeEco never addressed.
giaur said:
Which bug your fix is intended to fix? Do you mean this:
- I have never seen it on my device.
Or you mean color calibration, which is currently terrible by default (too much yellowish)
Click to expand...
Click to collapse
How do i view the config files and transfer them to my computer to compare them to yours? I enabled usb debugging, thinking that would let me see everything but when i connect to my computer with MTP mode i can only see standard files, not all the linux config files etc.
(edit: I tried using adb shell and i could view the root directory but it wouldn't let me access the config folder - permission denied. Do i need root access? If so, how do i get it temporarily and then remove it once i have transferred the files? I can't just run adb as root because you need root on the phone apparently).
Also i did a search of the available EUI x829 source (http://opensource.le.com/ or http://opensource.le.com/ or https://forum.xda-developers.com/le-max-2/how-to/source-code-available-t3482334 )and i couldn't find those xml files. Are they generated by the OS or something?
To me it seems like the files are probably already formatted correctly on my particular phone as changing the colour mode does appear to function. However they obviously seem to be not calibrated properly (or intentionally calibrated very badly).
I wonder if it only reads these files on boot? Otherwise i guess an application could be made to interactively adjust them.
I wonder if KCAL uses these files.
However from looking at how large the data is and also the mention of LUTs (lookup tables), it would seem that this is actually more advanced than kcal? And could potentially give proper screen calibration if using a colourimeter etc?
Of course, more than one profile would be necessary for different brightness levels though.
But anything is better than nothing.
It is definitely to do with the eui colour mode settings because if you go to google translate and translate the names in for each profile, they match up with colour mode options.
These are part of EUI ROM as I did mention the XML formatting is broken on all the EUI ROM versions I looked at.
You can use an Android ROM extractor like this to open up EUI ROM and see the files yourself if you'd like.
https://forum.xda-developers.com/android/help/extract-dat-marshmallow-lollipop-easily-t3334117
I found this https://usermanual.wiki/Pdf/KBA160907024936QDCMPCToolDebugGuide.968066270 which implies that the xml file is used directly.
Have you considered that <Calib_Data /> just means that the Calib_Data section is empty deliberately and that the colour profile and LUT sections were never intended to be within the calibration data tag?
We do not have the specification of the QDCM xml file that the tool generates.
It would be beneficial if the QDCM tool could be somehow leaked or obtained, then the end user could calibrate their phones. Or at least a specification of the file format of the QDCM xml files so correct data could be generated.
I suggest this should be brought up to the wider android community as it applies to all recent qualcomm phones.
Then we can compare with the QDCM xml files distributed with their handsets. Maybe some handsets even contain the same panels and therefore maybe we could attempt to use their profile / calibration settings. Of course it won't give perfect results because screens should be calibrated on an individual basis but it might be a lot better than the awfullness i currently have.
I wonder, do Le Eco calibrate each handset individually because if they do and then CFW overwrites the calibration with a "random" one then i can understand how that would cause issues. However my display has been bad before i loaded CFW... (unless the seller tampered with the FW but i don't know how you are meant to tell that).
I am not saying you are wrong but you have not given sources for your findings and to me, the individual colour profiles are working it's just that the overall calibration (or all of the profiles themselves) is extremely awful with huge black crush.
That tools seems to be for looking at backup images? But i want to view what is on my phone currently. Do you have to root your phone to do so? If so how can i root and then unroot it after i'm done?
Thanks
oneNight1 said:
I found this https://usermanual.wiki/Pdf/KBA160907024936QDCMPCToolDebugGuide.968066270 which implies that the xml file is used directly.
Have you considered that <Calib_Data /> just means that the Calib_Data section is empty deliberately and that the colour profile and LUT sections were never intended to be within the calibration data tag?
We do not have the specification of the QDCM xml file that the tool generates.
The way the XML formatting is? Calib_Data is supposed to house the entire XML file to let QDCM know where the calibration data starts and ends... So on the broken EUI ROM XML files it only has an end and never loads the calibration data.
It would be beneficial if the QDCM tool could be somehow leaked or obtained, then the end user could calibrate their phones. Or at least a specification of the file format of the QDCM xml files so correct data could be generated.
I suggest this should be brought up to the wider android community as it applies to all recent qualcomm phones.
Then we can compare with the QDCM xml files distributed with their handsets. Maybe some handsets even contain the same panels and therefore maybe we could attempt to use their profile / calibration settings. Of course it won't give perfect results because screens should be calibrated on an individual basis but it might be a lot better than the awfullness i currently have.
I wonder, do Le Eco calibrate each handset individually because if they do and then CFW overwrites the calibration with a "random" one then i can understand how that would cause issues. However my display has been bad before i loaded CFW... (unless the seller tampered with the FW but i don't know how you are meant to tell that).
I am not saying you are wrong but you have not given sources for your findings and to me, the individual colour profiles are working it's just that the overall calibration (or all of the profiles themselves) is extremely awful with huge black crush.
That tools seems to be for looking at backup images? But i want to view what is on my phone currently. Do you have to root your phone to do so? If so how can i root and then unroot it after i'm done?
Thanks
Click to expand...
Click to collapse
Heyyo, it's definitely a formatting error. XML standard has open and close brackets.
For example, the OnePlus 5T
https://github.com/TheMuppets/propr...b_data_samsung_s6e3fc1_cmd_mode_dsi_panel.xml
Or the Xiaomi Mi5 (Gemini)
https://github.com/TheMuppets/propr...calib_data_sharp_fhd_cmd_incell_dsi_panel.xml
As for viewing the files on your phone? Yes you would need root and a root file explorer.
Magisk, SuperSU, KingRoot or such all work for root but some versions of EUI ROM have issues.
For root enabled file browser? Amaze works... Amazing. Just get it from the Play store and then in settings enable root explorer.
For uninstalling root please Google the uninstall method to whichever root method you use as they are all different.
That's not true, XML tags can close themselves. If you don't believe me look here: https://www.w3schools.com/xml/xml_elements.asp (scroll down to empty xml elements)
How they had formatted their tags was valid xml.
Code:
<Calib_Data />
is just an element with nothing in it, the same thing as:
Code:
<Calib_Data> </Calib_Data>
However what you showed me from the other xml files for other phones make it look like it should be the way you have changed it
Okay i will have a look and let you know. I have small eui installed atm. So if you just flash an su to your system and then once you uninstall the app root is completely gone? I never would have thought it would be that simple.
It seems when you have root you can use an adb shell as root so i might try that rather than bothering to install anything on the phone.
Is there a way also to view what it was in the backup of my original fw without restoring it? (i used this guide for backup https://forum.xda-developers.com/le-max-2/how-to/protocol-backup-stock-rom-flash-stock-t3517151 ).
How can i find out which of the 3 display types my device is using? (Preferrably via adb).
I will be really surprised if it's wrong in mine because the colour modes work which will be very weird if that xml file isn't being used - they must do it another way too if that's the case :S
It's also weird how those xml files have been hand tampered with!
Thanks!
oneNight1 said:
That's not true, XML tags can close themselves. If you don't believe me look here: https://www.w3schools.com/xml/xml_elements.asp (scroll down to empty xml elements)
How they had formatted their tags was valid xml.
Code:
<Calib_Data />
is just an element with nothing in it, the same thing as:
Code:
<Calib_Data> </Calib_Data>
However what you showed me from the other xml files for other phones make it look like it should be the way you have changed it
Okay i will have a look and let you know. I have small eui installed atm. So if you just flash an su to your system and then once you uninstall the app root is completely gone? I never would have thought it would be that simple.
It seems when you have root you can use an adb shell as root so i might try that rather than bothering to install anything on the phone.
Is there a way also to view what it was in the backup of my original fw without restoring it? (i used this guide for backup https://forum.xda-developers.com/le-max-2/how-to/protocol-backup-stock-rom-flash-stock-t3517151 ).
How can i find out which of the 3 display types my device is using? (Preferrably via adb).
I will be really surprised if it's wrong in mine because the colour modes work which will be very weird if that xml file isn't being used - they must do it another way too if that's the case :S
It's also weird how those xml files have been hand tampered with!
Thanks!
Click to expand...
Click to collapse
Write this in the terminal.
Code:
cat /sys/devices/virtual/graphics/fb0/msm_fb_panel_info | grep panel_name
Thanks Sergio, so my device is running:
Code:
le_x2_mdss_dsi_truly_qhd_dualdsi_cmd_pvt
Hmm it seems that SmallEUI ( https://forum.xda-developers.com/le-max-2/development/rom-small-eui-5-9-aurel-battery-t3524531 ) wiped the configs folder. It looks the same through both ADB --> shell ---> su ---> cd config as it does through the Amaze app on the phone itself - empty.
I am pretty sure that I have root properly, supersu seems to be installed.
For some reason though, if i try and get ADB to get root, it says:
Code:
adbd cannot run as root in production builds
I don't have a folder named configs, only one called "config" and it is completely empty.
Is there any way to view the files that were in my TWRP backup of my stock X829 FW without reflashing it?
I have lots of data.ext4.win000 files etc. Which archive would it be in? System? Data? EFS? Boot? And how do i browse the archives?
Thanks
oneNight1 said:
Thanks Sergio, so my device is running:
Code:
le_x2_mdss_dsi_truly_qhd_dualdsi_cmd_pvt
Hmm it seems that SmallEUI ( https://forum.xda-developers.com/le-max-2/development/rom-small-eui-5-9-aurel-battery-t3524531 ) wiped the configs folder. It looks the same through both ADB --> shell ---> su ---> cd config as it does through the Amaze app on the phone itself - empty.
I am pretty sure that I have root properly, supersu seems to be installed.
For some reason though, if i try and get ADB to get root, it says:
Code:
adbd cannot run as root in production builds
I don't have a folder named configs, only one called "config" and it is completely empty.
Is there any way to view the files that were in my TWRP backup of my stock X829 FW without reflashing it?
I have lots of data.ext4.win000 files etc. Which archive would it be in? System? Data? EFS? Boot? And how do i browse the archives?
Thanks
Click to expand...
Click to collapse
You should notice this does not work, garbage screen is there even with this fix applied. I have it all the time on latest Lineage 15.1.
Okay I checked in
Code:
system/etc
and I do have the files. They are formatted as
Code:
<Calib_Data />
too.
Why does your github page say that they should be in
Code:
config/qcdm
???
Anyway, I flashed your zip to see if it would make a difference but it didn't help with the black crush sadly.
Although maybe modifying the calibration data would - but of course we would need to understand the format.
I checked my TWRP backup image (you can just browse them with 7zip) and they have the same empty tag too.

Categories

Resources