Hi i need help with this problem, i have a Motorola Milestone x MB809 and i programing my cellphone and this cellphone in the boot is freeze in the screen only i see a logo, i need help for unfreze and install another stock finware or rom for fixed my cellphone i wait for the best solution thanks...
I know nothing about the milestone X...
But what were you attempting to do when your phone did this?
You're probably going to have to either SBF or do a factory reset from the stock recovery.
I don't know if you have a special SBF file for the milestone X, but I'm sure you can find info via google.
If you want, you can try to pull the battery for a few seconds...
Put it back in...
Hold both the home button + the power button until an android with an exclamation point shows up.
Then press the search button.
Navigate to factory reset.
You'll lose all of your applications and such, but I can't think of a better route for you to try anyway.
If that doesn't work, you'll have to find an applicable SBF.
Related
Managed to get my Droid 2 to a point where it will not go beyond the M screen on boot. I've tried pulling the battery over and over again and cannot get to the Clockwork bootstrap. I've also tried plugging it in and pulling the battery many, many times.
So I figure the next best step is to .sbf this mofo.
I've downloaded & installed rdslite, the USB drivers. Also have the Droid 2 .sbf files. Droid.Co_Downloader.exe pulled down RSD Lite v4.8 though rather than 4.7. And the link to 4.7 is now showing as invalid. Will 4.8 work for what I'm trying to do?
Also, when I plug in my phone RSD Lite never shows anything in the devices table. What are the steps to get my phone to show up? Plug in phone, power on, turn on RDS Lite? The tutorial seemed to be aimed at people who still have working phones in that it has you adjusting setting on the phone i.e. enable debug mode.
Sidenote, I know debug mode is disabled on my phone. Does that mean RSD Lite isn't going to work?
Help!
I think if you pull and replace the battery at the M it should reboot into recovery, and if it won't do that you can always try sliding out the keyboard and booting the phone while holding the X key to see if it will dump you into the stock recovery
Ok, some more reading uncovered hitting the physical keyboard's Up arrow and powering on will take the phone to the Bootloader and once in the bootloader my pc recognized it.
And then RSD Lite showed my device in the table but it didn't show up as the A955 it was Model "S Flash OMAP3630 MI".
Currently flashing DROID2_X6_2.2.20 .sbf, hopefully that pans out.
Thanks, I tried the battery pull thing A LOT of times. Never went into bootstrap. Not sure what's going on there.
I tried the stock recovery but got the Android-exclaimation mark icon which I presume means the stock recovery was F-ed up.
Really hope this sbf recovery works.
Ok, disaster averted.
Looks like rebooting into the bootloader was the secret. Hope that is helpful to someone else who's bricked their phone.
BTW, used RSD Lite version 4.8 and that worked with my Droid 2.
aplus01 said:
Thanks, I tried the battery pull thing A LOT of times. Never went into bootstrap. Not sure what's going on there.
I tried the stock recovery but got the Android-exclaimation mark icon which I presume means the stock recovery was F-ed up.
Really hope this sbf recovery works.
Click to expand...
Click to collapse
Glad you got it working! For future reference if you want the stock recovery, after you hold x and get to the exlamation point, press the search key on the keyboard. (The little magnifying glass) and it should take right Into it.
Sent from my DROID2 using XDA App
Me too!
Search key? Good to know. Man, that could have saved me quite a bit of time I think.
So now that I've restored everyting I'm going to risk it all and install the fission rom again.
It's less intimidating now that I know how to sbf restore. Hopefully I won't need to this go round.
Just follow the instructions as they are laid out and you shouldn't run into much trouble. Also, be sure to let the device sit for a bit after you reboot from clockwork, as it could take a good 15 minutes before it fully boots up the first time, and interrupting that could put you back at square one
Could you add [SOLVED] to your thread title please. Thanks
ok i got a droid 2 and it only goes to the motorola symbol screen and then shuts back off and starts up again and it will sometimes say the bootloader isnt working
Did you get this phone from Verizon or did you buy it from a third party? If you got it from Verizon, take the phone back and get a new one. If you didn't, then try flashing an SBF.
Here are the instructions on how to do that:
http://forum.xda-developers.com/showthread.php?t=770224
I believe the download there isn't working, so you can download the sbf from here:
hxxp://www.droid-life.com/2010/11/01/droid-2-sbf-released-for-2-3-20-update/ (replace xx with tt)
BE SURE after you flash the SBF to hold X on the keyboard and your power button to boot into recovery and wipe your data and cache or you will be stuck in a bootloop, and after your phone boots up you will need to reactivate it, but it should do that for you when you sign into google.
Hopefully this will solve your problem. If not, check back and maybe someone else can be of further help.
I installed Gingerbread that was recently released by team black hat, it was working perfectly for a few days, then all of a sudden.....im stuck at M logo. So i followed P3Droid's instructions , down loaded all the necessary files and tried to flash the 2.3.20 sbf file and nothing happens. When i connect my phone to RSD Lite (tried 4.7, 4.9) it does not recognize my phone, it says my phone model is sflash, not droid 2 or a955. I went ahead and tried to flash but when it hits 100% it says please manually power up phone and i do....still stuck at M logo. Im ****ed, my phone is a brick, this suck! Everyone elses phone I root works perfect, except mine.....please help me if u can!!
make sure you have the correct moto drivers on your computer and make sure they are for the correct bit of your OS also. whenever i sbf the phone reboots itself.
I got all the updated files...i found it weird that my phone dosnt power up on its own. In rsd lite does it show ur phone model or show it as sflash? Mine shows as sflash, thats what i think the prob is.
evilteam00 said:
I got all the updated files...i found it weird that my phone dosnt power up on its own. In rsd lite does it show ur phone model or show it as sflash? Mine shows as sflash, thats what i think the prob is.
Click to expand...
Click to collapse
Mine shows up as sflash, but the SBF has always worked correctly, even when flashing back from 2.3
Have you ever SBF'd before, and if so, has it worked?
Also, have to tried getting into the stock recovery? Try to, and wipe data and cache and see if that helps any.
Also, you may try uninstalling the moto drivers, rsd, redownload and reinstall them, and also try redownloading the SBF file.
orkillakilla said:
Mine shows up as sflash, but the SBF has always worked correctly, even when flashing back from 2.3
Have you ever SBF'd before, and if so, has it worked?
Also, have to tried getting into the stock recovery? Try to, and wipe data and cache and see if that helps any.
Also, you may try uninstalling the moto drivers, rsd, redownload and reinstall them, and also try redownloading the SBF file.
Click to expand...
Click to collapse
Ive flashed SBF'd SPrecovery a long time ago with my droid 1, it worked fine. Tried uninstalling the drivers sbf file and rsd, then reinsalled them. When I hold X and power my phone just stays stuck on the M logo. Im not sure what im dokng wrong...i followed the steps from here...http://forum.xda-developers.com/showthread.php?t=770224
What sbf are you using? I use the full system sbf from here:
h t t p://www.mydroidworld.com/forums/droid-2-discussion/5323-tbh-mydroidworld-present-droid-2-2-3-20-triple-threat.html
Try that if you aren't using that one.
Also, what bootloader version do you have? Mine is 2.37
Sent from my Liberated DROID 2
This happened to me, and I almost **** a brick. You need to hold down the power, and X buttons simultaneously, until the exclimation point in the triangle comes up. Then hit the Search button on the keyboard, which is directly below the X. If it's not working flash And again, and make sure you have the correect drivers from Motorola on your PC.
Sent from my LiberatedDROID2 using Tapatalk
AKSurprise said:
This happened to me, and I almost **** a brick. You need to hold down the power, and X buttons simultaneously, until the exclimation point in the triangle comes up. Then hit the Search button on the keyboard, which is directly below the X. If it's not working flash And again, and make sure you have the correect drivers from Motorola on your PC.
Sent from my LiberatedDROID2 using Tapatalk
Click to expand...
Click to collapse
He already said that he cannot get into stock recovery.
Besides, GB stock recovery is different from froyo. Instead of hitting the search button, you have to hit vol up and vol down at the same time. Then use the volume keys to go up and down, and the power button to select.
I think i may need a working droid 2 to make sure the drivers all installed correctly.....a guy was helping me out and he thinks thats the prob. I had 2.37 bootloader and the full system sbf file, that didnt work so I went to bootloader 2.35 with full sbf, and still stuck at M logo. I hope its the drivers cuz before my phone bricked i diddnt have the latest drivers...Gotta wait a few hours till i get another droid 2 to see if that was the prob. Thanks for the suggestions.
good night friends!
I'm here asking for this help not for lack of looking for the solution, sorry my bad english, I'm from Brazil and I
defy caught in a bootloader, I tried almost everything I found here in the forum, but most of the problems is
reset solved by making the recovery, but in my defy the recovery does not open, the flash works only power + vol up, already
I spent several roms to no avail, could someone help me run my recovery? grateful heart
list of roms flashead
JRDNEM_U3_3.4.2_155-002_DEBLUR_SIGN_SIGNED_UCAJRDNEMARAB1B80AA03A.0R_PDS03C_USAJRDNFRYORTCEE_P011_A010_HWp3_Service1FFJORLA_U3_3.4.2_107-7_R02_SIGNED_USAJORDMR1B15CLABRLA019.0R_JORLAFROCLABRLA_P009_A008_M002_HWp3_Service1FF.sbfz
JORLA_U3_3.4.2_107-7_R02_SIGNED_USAJORDMR1B15CLABRLA019.0R_JORLAFROCLABRLA_P009_A008_M002_HWp3_Service1FF.sbf
JRDNEM_U3_2.34.1_DEBLUR_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA02B.0R_USAJORDANRTCEE_P029_A019_HWp3_Service1FF.sbf
JRDNEM_U3_2.51.1_BLUR_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA030.0R_USAJORDANRTFR_P043_A010_HWp3_Service1FF.sbf
JRDNEM_U3_2.59.0_CHN_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA035.0R_USAJORDANRTHKTW_P021_A015_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_117-002_BLUR_SIGN_SIGNED_USAJRDNEMARAB1B8RTGB035.0R_USAJRDNFRYORTGB_P003_A002_HWp3_Service1FF
JRDNEM_U3_3.4.2_164-003_VFBLUR_SIGN_SIGNED_USAJRDNEMARAB1B8VFFR03A.0R_PDS03C_USAJRDNFRYOVFFR_P028_A014_M004_HWp3_Service1FF.sbf
Motorola_Defy_Nu___Android_2.2_FroYo
shadow_defy_2.3.3_85_Orange
If you turn it on while holding "dolume down" do you get the android+! screen? Some go into recovery if you touch the bottom right corner of the screen, but on some you have to hold volume up + down together. I had this problem today!
If you actually can't get to the screen with the android+! then I don't know what else you could do :-(
mmec2 said:
If you turn it on while holding "dolume down" do you get the android+! screen? Some go into recovery if you touch the bottom right corner of the screen, but on some you have to hold volume up + down together. I had this problem today!
If you actually can't get to the screen with the android+! then I don't know what else you could do :-(
Click to expand...
Click to collapse
I really can not, no way to go to the screen with the robot android! he goes right on the logo motorola M!
can it be hardware problem?
1) Did you use the correct flasher? rsd4.9 with motorola driver installed properly.
2) If (1) not working, you could use motorola own service update from their site.
farsight73 said:
1) Did you use the correct flasher? rsd4.9 with motorola driver installed properly.
2) If (1) not working, you could use motorola own service update from their site.
Click to expand...
Click to collapse
I'm using motorola rsd 4.9 with updated drivers, what happens is install the rom normal after reboot gets stuck in the Motorola M logo, the software update site does not recognize my phone, do all these roms that I would be no my phone?
im tried this roms now
JRDNEM_U3_2.51.1_BLUR_P3_SIGN_SIGNED_UCAJRDNEMARAB1B80AA030.0R_USAJORDANRTFR_P043_A010_HWp3_Service1FF.sbf
JRDNEM_U3_3.4.2_117-002_BLUR_SIGN_SIGNED_USAJRDNEMARAB1B8RTGB035.0R_USAJRDNFRYORTGB_P003_A002_HWp3_Service1FF
JRDNEM_U3_2.21.0_SIGNED_UCAJRDNEMARAB1B80AA028.0R_USAJORDANRTGB_P026_A007_HWp3_Service1FF
3.4.3_11-Stock.UKTmobile_BLUR
but no results!
don't worry about it, dude.
maybe you can try the way followed:
1.power off your defy;
2.remove the battery from the phone;
3.plug the usb cable into the phone without battery;
4.open RSD and chose one of the roms your listed, but 3.4.2-177-005 NORDIC prefered,
5.take the battery into your phone, now your can see the "connected" on RSD;
6.click the "start" button to flash;
7.wait the phone reboot completely, usually it'll reboot.
if not reboot, remove and on your battery, power on your phone, then press the "volume - and power" botton together, you can enter the robot screen, press volume up and down botton together, usually you can enter the recovery, then chose wipe 3 and 4, totally you can save your defy~~
Be sure to have enough battery while flashing..
Get the phone into bootloader (hold volume down when switch on) and flash an SBF like one from the list you've attached using RSD lite. Surely you have used RSD Lite before?
It seems you have the same issue I have on my Defy as per this thread: http://forum.xda-developers.com/showthread.php?t=1095444
I’m also unable to get into recovery or get to the Android Robot screen using “Power + Volume Down”. Hopefully we will be able to figure it out and get this issue fixed.
jdearauj said:
It seems you have the same issue I have on my Defy as per this thread: http://forum.xda-developers.com/showthread.php?t=1095444
I’m also unable to get into recovery or get to the Android Robot screen using “Power + Volume Down”. Hopefully we will be able to figure it out and get this issue fixed.
Click to expand...
Click to collapse
This same friend, I have the same problem, is this a hardware problem? I move the roms but not normal
Vol I login recovery - + Power key
http://forum.xda-developers.com/showthread.php?t=966537
Try flashing nordic, if fails arabic, if fails, 2.3.3, if fails probably corrupt nand broken hardware.
Before and after every flash always try to access recovery (volume down) and WIPE. reboot and wait crossing fingers, if it fails to boot flash next sbf, try to go recovery + wipe; reboot, cross more fingers; if fails to boot try next sbf and repeat.
The reason for this is that you can flash a lower version but it wont boot, so you have to flash a higher and higher version until you get one that works.
I tried to help someone with this problem before to no avail!
Everyone who is saying just wipe in recovery, or just flash with RSD blah blah blah, need to understand that he CAN NOT access recovery and HE HAS flashed multiple roms using RSD 4.9, read the OP. Im convinced this is physical hardware failure or similar. We all know the drill to recover our precious defy's in the event of semi-brick ie: bootloop or corrupt code. However this is more than a semi-brick. We are talking about successful flashing and still no access to recovery and infinite M logo!
I walked more than one person with this problem through every known procedure to bring these phones back. Even using sbf_flash for linux doesn't work as this is the only way I flash anymore I don't bother with RSD anymore. The thing is it DOES FLASH SUCCESSFULLY just no recovery or boot!
zyxwvut said:
I tried to help someone with this problem before to no avail!
Everyone who is saying just wipe in recovery, or just flash with RSD blah blah blah, need to understand that he CAN NOT access recovery and HE HAS flashed multiple roms using RSD 4.9, read the OP. Im convinced this is physical hardware failure or similar. We all know the drill to recover our precious defy's in the event of semi-brick ie: bootloop or corrupt code. However this is more than a semi-brick. We are talking about successful flashing and still no access to recovery and infinite M logo!
I walked more than one person with this problem through every known procedure to bring these phones back. Even using sbf_flash for linux doesn't work as this is the only way I flash anymore I don't bother with RSD anymore. The thing is it DOES FLASH SUCCESSFULLY just no recovery or boot!
Click to expand...
Click to collapse
OMG Exactly!!!! i have same problem and nobody seems to be able to tell me what to do, they keep saying same thing about trying various SBF's and Vol down + power method. No matter what SBF file I successfully flash with, i cannot get into boot recovery mode.
I have heard before from desperate users that they were able to revive their phone by flashing a full 2.3.4 sbf. This however comes with downsides of not being able to downgrade to froyo by flashing ANY froyo sbf's. There is a way to downgrade back to froyo but its a dirty method. Even after downgrade you can't just flash a sbf, you will always need to restore nandroid and flash fixed sbf
So i have been having issues with my Droid X since i rooted it. It has a locked bootloader so idk if that effects it. In the last few weeks ive have to go into my bootstrap and factory reset my phone about a week ago, yesterday and now again tonight. The thing is i cant even get my Droid X to boot past the red M. Im stumped on what to do and i need help.
Wrong place to post
Ask a mod to move this to Droid x general/q n a, I'm sure you'll get some help there
From my fingers to your eyez
Well, your applications and data are done-for, unfortunately.
Pull the battery...and from a dead state:
Hold HOME+POWER.
Continue to hold home until a green android pops up.
I always forget what comes next on gingerbread...
but I think it's both volume keys at the same time.
Navigate and select to do a factory reset.
Try booting.
If it still won't boot...
You'll have to SBF
http://rootzwiki.com/topic/331-guide-flashing-droid-x-sbf/
Use the 602 sbf.
If you ever want to flash a custom rom, I've made a quick guide that'll make the process easier on a new user.
http://forum.xda-developers.com/showthread.php?t=1374281