Related
Hi everyone,
I'm having a problem with my G1.
Each time i try to turn the Wi-Fi on, i follow this steps (spoil !!) :
- Settings -> Wireless controls -> and the i click on Wi-Fi,
wich changes the lower text to "Turning on..."
Ok, but this step take something like 1 minute and after all this time, i can read : "Unable to stop Wi-Fi" (or sometimes "Unable to start Wi-Fi"),
I got this problem 5 days ago, and this is really a pain in the arse, because the only way i can download applications is using Wi-Fi (I'm french) and i can't !
I have tried everything :
- Turn Off/On G1
- Remove/Replace battery
- Reset to factory data
- Back to RC29 (thx to you )
- Root my G1 with JF1.41 mod (Thx so much !!)
But the problem is still there,
And i can't get it back to T-Mobile, because i bought it on eBay and i live in France...
So... can anybody help ?
Thx
Hi,
Same problem here. Edit: It does this 4 times on 5. And even if if finally starts, it hangs some time after.
Additionally I've googled (almost) all night long to find some clues but nothing concrete
First, an issue is open here: http://code.google.com/p/android/issues/detail?id=1124
I get this line in logcat:
Code:
D/wlan_loader( 574): ConfigMge start rc = -1
that shows a problem. Normally it should be "rc = 0".
I've digged into the code but it is very complicated (state machine, etc...) so I could not figure where the problem resides.
I also have this in dmesg:
Code:
<4>[ 1425.145012] mmc0: card claims to support voltages below the defined range. These will be ignored.
<4>[ 1425.145867] mmc0: SDIO card claims to support the incompletely defined 'low voltage range'. This will be ignored.
I don't know if this means a hardware problem.
I also suspect a bug in the proprietary file "/system/etc/wifi/Fw1251r1c.bin" but I've not found any other version on the net, even in "not so clean ways".
The size of the file on my G1 is 194188 bytes.
I have installed RC33 ADP1 by Jesus Freke but it did not solved the problem.
Can anyone look at the size of this file on his G1 and tell me if it is different? And if it is the case possibly send it to me?
The only solution I've seen on the net is to send back the phone to T-Mobile for a replacement but unfortunately I live in France and I got it from US by unusual ways so it is not a possibility for me .
Any clue / advice will be gladly accepted
Thanks in advance.
Mid'.
I have the same problem...
I was wondering if either of you figured out what to do to get around this. I'm in the US and am having the same problem. I was also working for about a week before this behavior started ("Unable to start Wi-Fi", "Unable to stop Wi-Fi").
I have seen other posts where this is intermittent. It isn't with me. Once it quit working, I haven't been able to get anything but the error messages.
If someone has found a way around this, I would appreciate any help you can provide.
Regards
Steve
You three should post what third party apps you have installed.
I am having this same issue after flashing the new google ION R2
I'm also having this issue after flashing Ion.
Same Issue
I started having this issue before the Ion rom. It wasn't intermittent, just stopped working.
Same problem here
Code:
<4>[ 1425.145012] mmc0: card claims to support voltages below the defined range. These will be ignored.
<4>[ 1425.145867] mmc0: SDIO card claims to support the incompletely defined 'low voltage range'. This will be ignored.
CRB43, factory reset, nothing works.
Does anybody have an idea on how to solve this? It seems to be a known problem bij T-Mobile.
I'm running JF1.51 and WiFi is horribly flaky. It will work great for a few seconds then go deaf.
If I toggle it off and on it will work for a little bit again.
EDIT: I'm also getting the "low voltage" error message.
I've looked at this a little bit, and it looks like a ring buffer problem.
As I said before, my WiFi will work great for a while then go deaf.
Disabling/enabling through the Settings GUI will restore operation for a couple of minutes, tops.
Here's what I think might be relevant dmesgs:
Code:
<6>[88157.446136] request_suspend_state: sleep (0->3) at 88153591964926 (2009-06-27 20:57:10.146884034 UTC)
<4>[88157.467956] deinit sharp panel
<4>[88157.996398] select 4913 (app_process), adj 15, size 3053, to kill
<4>[88157.996734] send sigkill to 4913 (app_process), adj 15, size 3053
<4>[88158.236358] save exit: isCheckpointed 1
<6>[88282.505401] request_suspend_state: wakeup (3->0) at 88278651260580 (2009-06-27 20:59:15.206149170 UTC)
<6>[88282.615966] rev_crc_err_count 1, INT 23a001
<6>[88282.616332] rev: unknown reverse packet: len=0009 type=0049 CURR_REV_PTR=1617500b
<6>[88282.616851]
<6>[88282.617126] 09<6> 00<6> 49<6> 00<6> 00<6> 80<6> 00<6> 60<6> 00<6> 80<6> 0a<6>
<6>[88282.620574] mddi: resetting rev ptr
<6>[88282.621154] mddi_remote_read: failed, sent MDDI_CMD_SEND_RTD: int 23a001, stat 808063, rtd val e curr_rev_ptr 1617500b
<4>[88282.666717] init sharp panel
<4>[88287.779876] select 4943 (app_process), adj 15, size 2991, to kill
<4>[88287.780731] send sigkill to 4943 (app_process), adj 15, size 2991
<4>[88295.748840] select 4951 (app_process), adj 15, size 2992, to kill
<4>[88295.749694] send sigkill to 4951 (app_process), adj 15, size 2992
<6>[88298.065185] TIWLAN: Driver unloading
<4>[88298.066314] sdio_reset_comm():
<7>[88298.154388] TIWLAN: Releasing SDIO resources
<7>[88298.158172] TIWLAN: SDIO resources released
<4>[88298.160217] wifi_remove
<4>[88298.160552] trout_wifi_set_carddetect: 0
<7>[88298.160827] mmc0: card_present 0
<6>[88298.161346] mmc0: Slot status change detected (1 -> 0)
<4>[88298.161712] trout_wifi_reset: 1
<6>[88298.172302] mmc0: card 0002 removed
<4>[88298.233215] trout_wifi_power: 0
<6>[88298.996520] TIWLAN: Driver unloaded
Here's a little more that I'm getting when the WiFi stops. Is this driver OSS or a proprietary blob?
Code:
<3>[ 1097.459899] init: untracked pid 364 exited
<4>[ 1101.746643] wds: 0020 @ 01
<6>[ 1101.747192] qmi: wds: got handle 0x17aaafb0
<4>[ 1101.747711] wds: 0022 @ ff
<6>[ 1101.748168] qmi: wds: CONNECTED
<4>[ 1101.750244] wds: 002d @ 01
<4>[ 1101.750701] qmi: got network profile
<6>[ 1101.752502] rmnet_open()
<6>[ 1685.105285] request_suspend_state: wakeup (3->0) at 1679298966064 (2009-06-27 21:55:33.740494873 UTC)
<6>[ 1685.217498] rev_crc_err_count 1, INT 23a001
<6>[ 1685.218078] rev: unknown reverse packet: len=0009 type=0049 CURR_REV_PTR=1617500b
<6>[ 1685.218383]
<6>[ 1685.218658] 09<6> 00<6> 49<6> 00<6> 00<6> 80<6> 00<6> 60<6> 00<6> 80<6> 0a<6>
<6>[ 1685.222137] mddi: resetting rev ptr
<6>[ 1685.222595] mddi_remote_read: failed, sent MDDI_CMD_SEND_RTD: int 23a001, stat 808063, rtd val e curr_rev_ptr 1617500b
<4>[ 1685.288696] init sharp panel
<4>[ 1692.515502] wds: 0021 @ 01
<6>[ 1692.515838] qmi: wds: network stopped
<6>[ 1692.546508] rmnet_stop()
<4>[ 1693.342254] wds: 0022 @ ff
<6>[ 1693.342864] qmi: wds: DISCONNECTED
<6>[ 1704.187591] TIWLAN: Driver unloading
<4>[ 1704.188781] sdio_reset_comm():
<7>[ 1704.266632] TIWLAN: Releasing SDIO resources
<7>[ 1704.267944] TIWLAN: SDIO resources released
<4>[ 1704.270568] wifi_remove
<4>[ 1704.271057] trout_wifi_set_carddetect: 0
<7>[ 1704.272521] mmc0: card_present 0
<6>[ 1704.272979] mmc0: Slot status change detected (1 -> 0)
<6>[ 1704.276489] mmc0: card 0002 removed
<4>[ 1704.280487] trout_wifi_reset: 1
<4>[ 1704.332305] trout_wifi_power: 0
<6>[ 1704.543151] TIWLAN: Driver unloaded
<4>[ 1705.308166] wds: 0020 @ 01
<6>[ 1705.308715] qmi: wds: got handle 0x17aaafb0
<4>[ 1705.309234] wds: 0022 @ ff
<6>[ 1705.309661] qmi: wds: CONNECTED
<4>[ 1705.311370] wds: 002d @ 01
<4>[ 1705.311798] qmi: got network profile
<6>[ 1705.313690] rmnet_open()
<6>[ 1709.503326] TIWLAN: Driver loading
<4>[ 1709.504211] wifi_probe
<4>[ 1709.504486] trout_wifi_power: 1
<4>[ 1709.714965] trout_wifi_reset: 0
<4>[ 1709.766632] trout_wifi_set_carddetect: 1
<7>[ 1709.767303] mmc0: card_present 1
<6>[ 1709.767608] mmc0: Slot status change detected (0 -> 1)
<3>[ 1712.275085] mmc0: Command timeout
<4>[ 1712.282226] mmc0: card claims to support voltages below the defined range. These will be ignored.
<4>[ 1712.283081] mmc0: SDIO card claims to support the incompletely defined 'low voltage range'. This will be ignored.
<6>[ 1712.290405] mmc0: new SDIO card at address 0001
<6>[ 1712.296447] TIWLAN: Found SDIO controller (vendor 0x104c, device 0x9066)
<6>[ 1712.302520] TIWLAN: Driver initialized (rc 0)
<4>[ 1712.303436] TIWLAN: 1251 PG 1.2
<6>[ 1712.303863] TIWLAN: Driver loaded
<4>[ 1721.950164] wds: 0021 @ 01
<6>[ 1721.950500] qmi: wds: network stopped
<6>[ 1721.976440] rmnet_stop()
<4>[ 1726.546569] select 151 (app_process), adj 15, size 3009, to kill
<4>[ 1726.547149] select 158 (app_process), adj 15, size 3081, to kill
<4>[ 1726.547454] select 311 (app_process), adj 15, size 3246, to kill
<4>[ 1726.547973] send sigkill to 311 (app_process), adj 15, size 3246
<4>[ 1730.936798] wds: 0022 @ ff
<6>[ 1730.937652] qmi: wds: DISCONNECTED
I had the problem, i redid everything. just flashing the phone didn't help. downloaded the jf1.51 and did it again. logs would say wifi drivers not found. and guess what i checked and there were not there... I don't know 'who' or 'what' deleted them...
The only thing II suspect is the Backup program available on market for root users...or the "Privacy for rooted phones" prog
Same problem
Experiencing the same problem with my UK T-Mobile G1 (JF v1.51). Tried wiping, reseting, turning device off and on and removing battery, nothing has worked.
Is there any solution yet? I don't have any new apps installed and it is a fresh update, the problem was there prior to updating to jf v1.51
Any help will be appreciated
Did anyone manage to fix this? could it be related to the SDCard you are using?
Does everyone with non-working wifi on a G1 have this?
3 days ago, after I apply a chinese character sorting patch, i met this problem. So I wiped my phone, repartitioned my sdcard, reflashed the CM404 rom. And finnally got my wifi back.
But today I had this problem back again. I'm thinking is it because the sdcard I'm using is taking up to much battery power, so that the wifi module could not acquire enough power? This recalls me that I changed my sdcard exactly 3 days ago, right before I met this problem for the first time.
I am from India and G1 is very expensive over here. So, a friend bought me G1 from US and it reached in my hand yesterday . It is a T-Mobile G1. Was having same issue with Wifi and was showing "WiFi unable to start" . I tried rooting it and flashing with various ROM - issue remained. Lastly I downloaded a application from Market and installed. Named : WiFi Fixer by Zanshin-g1 .that software is written for completely different reason.
Code:
Does your wifi "hang" while still connected? Wifi Fixer keeps wifi working automatically, with optional wifi lock.
0.3.1 Cupcake, Disable function, warning if Wifi Notification is on
0.2.9 Added support for Landscape
*Wifi Fixer Classic also available*
But somehow it fixed my issue
Thanks Zanshin-g1.
bidhata said:
I am from India and G1 is very expensive over here. So, a friend bought me G1 from US and it reached in my hand yesterday . It is a T-Mobile G1. Was having same issue with Wifi and was showing "WiFi unable to start" . I tried rooting it and flashing with various ROM - issue remained. Lastly I downloaded a application from Market and installed. Named : WiFi Fixer by Zanshin-g1 .that software is written for completely different reason.
Code:
Does your wifi "hang" while still connected? Wifi Fixer keeps wifi working automatically, with optional wifi lock.
0.3.1 Cupcake, Disable function, warning if Wifi Notification is on
0.2.9 Added support for Landscape
*Wifi Fixer Classic also available*
But somehow it fixed my issue
Thanks Zanshin-g1.
Click to expand...
Click to collapse
Thanks Bidhata ,
but it tried that application and initially at first run it worked . but then once i got dc , the problem came back. since then i am not able to have the wifi truned on .
so the issue remains ..
Did you check the permission of this file: /data/misc/wifi/wpa_supplicant.conf
osoft said:
Did you check the permission of this file: /data/misc/wifi/wpa_supplicant.conf
Click to expand...
Click to collapse
This gave me the idea of how to fix, and its relativley simple... please correct me if I have made a grave error, but it seems to work so meh:
enter your terminal emulator and type the following:
su
(allow the request when asked)
chmod 777 /data/misc/wifi/wpa_supplicant.conf
exit the terminal
try powering up your wifi, it seems to be pretty stable as of now. This began occuring after I left my home's wireless range without turning wifi off and having the Wireless Helper app installed from the market...needless to say I have uninstalled said app and done this mod.
Whats funny about my situation is that if i use the DREAIMG.nbh file to flash back to rc29 my wifi works fine if i then upgrade to jf 1.5 still works fine upgrade to the latest cyanogen stable still works fine. Then a couple of days later poof "Unable to start wifi" intermittently and then a few days later permanently. Even if i downgrade to jf again still no wifi until i re-flash rc29 again. Weird thing is before i downgrade to jf 1.5 i run a fastboot erase on all the pertinent partitions. The only one that doesn't get flashed or erased in the downgrade to 1.5 is the radio rom. This leads me to believe that either my hardware is on it's way out or something that gets set in the radio rom from cyanogen 4.0.4 gets carried over no matter what rom you flash until the radio is erased and re-flashed. Mind you the second one is a totally just a guess with no proof to back it up. I also tried to chmod 777 /data/misc/wifi/wpa_supplicant.conf like said in the last post but to no avail.
I could not post directly in the development thread as I joined simply to share my solution. If anyone can confirm and prepare a better guide please post to CM7 thread by whistelstop.
You will need your factory mac address.
MAC Addresses all being the same is due to the nvs_map.bin file required by the tiwlan driver. dmseg driver will tell you it is looking for it and defaulting mac address.
I am running CM7 mileage will vary in stock rom.
http://www.omappedia.org/wiki/Porting_MCP_WLAN_to_Android#TxBiP_Calibration
I used the calibration instructions in terminal emulator on cm7 Kindle as "su"
#wlan_cu –b
# / w p 1 l 2 f 2
# / t b v 21
# / t b t 1 0 0 0 0 0 0 0
#/ q
New nvs_map.bin file will be ceated in /data/misc/wifi/
#cp /data/misc/wifi/nvs_map.bin to /sdcard/nvs_map.bin
connect to linux/windows host copy file to pc
open with hex editor I used xvi32 for windows.
link to my source for instruction for byte order and editing.
http://processors.wiki.ti.com/index...ce_(CLI)_User's_Guide#Editing_the_MAC_Address
Short instructions:
Editing the MAC Address
After the TX BIP runs, there is a new file called nvs_map.bin in Linux that contains the MAC address and the calibration data. The document SWAA044_NVS_INI_File_Functions_AN.pdf contains the format of the NVS file. If MAC address fields are manually edited with a hex editor, the byte order should be low byte first, followed by the high byte:
MAC address low register (offset 0x01 to 0x02)
MAC address LSB (offset 0x3 to 0x06)
MAC address high register (offset 0x08 to 0x09)
MAC address MSB (offset 0x0A to 0x0D)
The MAC address LSB and MAC address MSB, respectively, are shown in bold in the
following code for 08:00:28:12:34:56:
0000: 01 6d 54 56 34 12 28 01 71 54 00 08
For 11:22:33:44:55:66:
0000: 01 6d 54 66 55 44 33 01 71 54 22 11 00 00
Using a hex editor, you should change the bold numbers to the MAC address you
want to use.
Be careful about byte order and look closely at examples.
Good Luck
Please confirm instructions yourself and use at your own risk
Just tried that and it worked beautifully!
Thanks for that - great find!
TheKid2 said:
I could not post directly in the development thread as I joined simply to share my solution. If anyone can confirm and prepare a better guide please post to CM7 thread by whistelstop.
You will need your factory mac address.
MAC Addresses all being the same is due to the nvs_map.bin file required by the tiwlan driver. dmseg driver will tell you it is looking for it and defaulting mac address.
I am running CM7 mileage will vary in stock rom.
As I can not post links you will need to google my text and find correct link (noob)
maybe a moderator can fix for me.
######.omappedia.org/wiki/Porting_MCP_WLAN_to_Android#TxBiP_Calibration
I used the calibration instructions in terminal as "su"
#wlan_cu –b
# / w p 1 l 2 f 2
# / t b v 21
# / t b t 1 0 0 0 0 0 0 0
#/ q
New nvs_map.bin file will be ceated in /data/misc/wifi/
#cp /data/misc/wifi/nvs_map.bin to /sdcard/nvs_map.bin
connect to linux/windows host copy file to pc
open with hex editor I used xvi32 for windows.
link to my source for instruction for byte order and editing.
##processors.wiki.ti.com/index.php/OMAP35x_Wireless_Connectivity_WL1271_Command_Line_Interface_(CLI)_User%27s_Guide#Editing_the_MAC_Address
Short instructions:
Editing the MAC Address
After the TX BIP runs, there is a new file called nvs_map.bin in Linux that contains the MAC address and the calibration data. The document SWAA044_NVS_INI_File_Functions_AN.pdf contains the format of the NVS file. If MAC address fields are manually edited with a hex editor, the byte order should be low byte first, followed by the high byte:
MAC address low register (offset 0x01 to 0x02)
MAC address LSB (offset 0x3 to 0x06)
MAC address high register (offset 0x08 to 0x09)
MAC address MSB (offset 0x0A to 0x0D)
The MAC address LSB and MAC address MSB, respectively, are shown in bold in the
following code for 08:00:28:12:34:56:
0000: 01 6d 54 56 34 12 28 01 71 54 00 08
For 11:22:33:44:55:66:
0000: 01 6d 54 66 55 44 33 01 71 54 22 11 00 00
Using a hex editor, you should change the bold numbers to the MAC address you
want to use.
Be careful about byte order and look closely at examples.
Good Luck
Please confirm instructions yourself and use at your own risk
Click to expand...
Click to collapse
I'll verify tomorrow. Thanks for taking the time to help run this to ground and get a workaround.
** Deleted **
For new driver only ....
so next cm7 build will get the fix
right?
As it was my first post forum would not allow me to post links I am hoping someone will clean up solution and add to development thread.
whistlestop said:
I'll verify tomorrow. Thanks for taking the time to help run this to ground and get a workaround.
Click to expand...
Click to collapse
love this rom , I have four of these running on my router now with original factory mac addresses, Thank You for your work. I know from personal experience hours and hours can just disappear when you get involved with a project of this type.
Is there a way to get the factory MAC address while still in CM7 or do I have to load the stock ROM to get it and then go back to CM7?
I have not found am method other than loading stock software back on device.
If you only have one kindle on your network you most likely will never have a problem.
If you had more than one running cm7 you could have router issues as they all were reporting same mac address. You will not have any issues unless another cm7 kindle shows up on the same wireless access point as yours.
Unless you have a router log or something with your former mac address, I think you have to reload stock to find it. Thats what I did anyway.
Thanks to the OP for posting this; worked like a charm!
direct editing
could we use a hex editor to change the local file on the kindle?
I spotted one at the market place, and combined with SU privileges it might get the job done.
jfb9301 said:
could we use a hex editor to change the local file on the kindle?
I spotted one at the market place, and combined with SU privileges it might get the job done.
Click to expand...
Click to collapse
any hex editor should work. I am so use to using laptop still adjusting to touch keyboard.
Hopefully better instructions
having just stumbled through to OPs instructions (hats off to the OP for finding this). Successfully I might add, I thought I'd write up a hopefully more clear method of achieving this.
As I have had difficulty with the adb.exe command (connection issues, probably from a dodgy connection if I have too many USB devices plugged in) I chose to use applications local to my Kindle itself for as much as I could.
Apps:
adb.exe (the one that came with Kindle_Fire_Utility worked for me) grab a copy of this useful tool here kindle fire utility thread
Root explorer from the android market android market link
HexEditor android market link
Kindle fire
Computer
Data:
Your original MAC address - this might suck to get, as you will have to get it from your Kindle booted to stock Kindle Fire Firmware. I had installed CM7 using TWRP, so I booted to TWRP did a backup of my current CM7 OS, did a restore to the KF OS, booted to stock(rooted) opened up settings/device and nabbed that pesky MAC address, rebooted to TWRP, restored CM7.
Instructions:
connect KF to computer
open the computers start menu and select run, type CMD in the box
navigate to kindle_fire_utility/tools
type command: adb shell
adb should open and start communication with you Kindle
within the shell you have to type the following (be mindful of the spaces as they are important, ignore the #s as they are to make this post put the spaces in):
#wlan_cu –b
# / w p 1 l 2 f 2
# / t b v 21
# / t b t 1 0 0 0 0 0 0 0
#/ q
now use ctrl-c to end ADB, and command:
exit
to close cmd, you are done with windows.
now the kindle part...
open root explorer
/data/misc/wifi
select nvs_map.bin and copy to the sdcard, I made two copies and named the second nvs_map.bin.bak just in case things got screwed from this point on.
exit root explorer
open HexEditor
open /sdcard/nvs_map.bin and change the digits in the very first line of the file
(example from OPs post)
following code for 08:00:28:12:34:56:
0000: 01 6d 54 56 34 12 28 01 71 54 00 08 00 00
For 11:22:33:44:55:66:
0000: 01 6d 54 66 55 44 33 01 71 54 22 11 00 00
save the file
use root explorer to copy it back to /data/misc/wifi
long press the file and set permissions to RW-RW-RW-
Reboot.....
Done
---------- Post added at 04:09 PM ---------- Previous post was at 03:11 PM ----------
I confimed MAC address using my wifi router (DDWRT) is awesome.
Does anyone know a way to get CM7 to cough up the kindles MAC address?
I'm having some difficulties with these instructions. I've tried with the WiFi setting from CM7 on and off, and also with the full instructions from the omappedia.org site, and it's still not working. A quick Google didn't come up with anything.
This is my output (from an ADB shell, obviously):
Code:
# insmod /system/etc/wifi/tiwlan_drv.ko
# start wlan_loader
# ifconfig tiwlan0 up
# wlan_cu –b
ERROR - IpcWpa_Sockets_Open - can't connect the socket
******************************************************
Connection to supplicant failed
******************************************************
ERROR - IPC_STA_Private_Send - error sending Wext private IOCTL to STA driver (ioctl_cmd = 800003, res = -1, errno = 19)
ERROR - driver is not in RUNNING state!
user_main, start
\> Driver/, Connection/, Management/, Show/, Privacy/, scAn/, roaminG/, qOs/, poWer/, eVents/, Bt coexsistance/, Report/, dEbug/, biT/, aboUt, Quit
/ D S
\> Driver/, Connection/, Management/, Show/, Privacy/, scAn/, roaminG/, qOs/, poWer/, eVents/, Bt coexsistance/, Report/, dEbug/, biT/, aboUt, Quit
.../Driver> Start, sTop, stAtus
ERROR - IPC_STA_Private_Send - error sending Wext private IOCTL to STA driver (ioctl_cmd = 8000001, res = -1, errno = 19)
ERROR - Failed to start driver!
I have tried it with and without the first three lines (going straight to wlan_cu -b), and the / D S line is an unsuccessful attempt to start the driver. An attempt to just push through all the commands gives an error message with every line, and does not create the nvs_map.bin file.
Anyone have any ideas?
I had wifi on, and did not run the first 3 commands. No thoughts beyond that.
For reference, I am on the latest CM7 with the updated video stuff by wistlestop (I think)
csyria6919 & jfb9301,
I can confirm, you'll get the errors csyria6919 gets with WiFi OFF - turn on Wifi on the KF and then the ADB commands work without errors.
VERY NICE Fix - +1 thanks to TheKid2!
~J
csyria6919 said:
I'm having some difficulties with these instructions. I've tried with the WiFi setting from CM7 on and off, and also with the full instructions from the omappedia.org site, and it's still not working. A quick Google didn't come up with anything.
This is my output (from an ADB shell, obviously):
Code:
# insmod /system/etc/wifi/tiwlan_drv.ko
# start wlan_loader
# ifconfig tiwlan0 up
# wlan_cu –b
ERROR - IpcWpa_Sockets_Open - can't connect the socket
******************************************************
Connection to supplicant failed
******************************************************
ERROR - IPC_STA_Private_Send - error sending Wext private IOCTL to STA driver (ioctl_cmd = 800003, res = -1, errno = 19)
ERROR - driver is not in RUNNING state!
user_main, start
\> Driver/, Connection/, Management/, Show/, Privacy/, scAn/, roaminG/, qOs/, poWer/, eVents/, Bt coexsistance/, Report/, dEbug/, biT/, aboUt, Quit
/ D S
\> Driver/, Connection/, Management/, Show/, Privacy/, scAn/, roaminG/, qOs/, poWer/, eVents/, Bt coexsistance/, Report/, dEbug/, biT/, aboUt, Quit
.../Driver> Start, sTop, stAtus
ERROR - IPC_STA_Private_Send - error sending Wext private IOCTL to STA driver (ioctl_cmd = 8000001, res = -1, errno = 19)
ERROR - Failed to start driver!
I have tried it with and without the first three lines (going straight to wlan_cu -b), and the / D S line is an unsuccessful attempt to start the driver. An attempt to just push through all the commands gives an error message with every line, and does not create the nvs_map.bin file.
Anyone have any ideas?
Click to expand...
Click to collapse
Hi,
I only used docs as reference. Wifi should be turned on on Kindle. I issued all command from terminal emulator running on Kindle. Hope you have found solution that works for you. Also there are spaces in between just about every letter in the commands.
Let us know if you were successful.
Hello,
I am hearing about cpu utilization issue in another thread. http://forum.xda-developers.com/showthread.php?t=1411895
Can anyone running cm7 and using nvs_map file check utilization connected to secure network. My installation is not exhibiting cpu behavior stuck at 1008 that is being described. Wondering if using calibration file is actually improving performance.
As a side not same file can be used in the current build of ics they are developing in that thread.
cpu scaling issue does not show up on unsecured net. Need a few people to sound off here to determine if my kindles are the only ones not having scaling issue.
Thanks
Is there somewhere in cm7 to check cpu utilization, I looked everywhere ended up downloading task manager from market. Seems like task manager, and performance monitor should be in there somewhere. I am sure I am overlooking something simple.
Thanks
TheKid2 said:
Is there somewhere in cm7 to check cpu utilization, I looked everywhere ended up downloading task manager from market. Seems like task manager, and performance monitor should be in there somewhere. I am sure I am overlooking something simple.
Thanks
Click to expand...
Click to collapse
I used your guide, got CM7 on my device and will check that once I get home.
To check CPU utilization I'd recommend CPU Spy https://market.android.com/details?id=com.bvalosek.cpuspy
Hi all,
I have a problem with my defy, whitout fall or update the touch screen stop responding.
After some resets & sbf flashing I've noticed that the touch screen is ok only when there is no sdcard.
I've tried over sdcards with no more success.
The sdcard is readable, I can access with adb.
Clockworkmod access the sdcard too.
With sdcard dmesg :
qtouch_force_reset: Forcing HW reset
Unable to get gpio pin num for touch_pwr_enq
touch_write: Error while trying to write 2 bytes
qtouch_set_addr: Can't send obp addr 0x 0
qtouch_process_info_block: Cannot read info object block
qtouch_ts_probe:Cannot read info block -121, checking for bootloader mode.
Without sdcard :
qtouch_force_reset: Forcing HW reset
Unable to get gpio pin num for touch_pwr_en
qtouch_process_info_block: Build version is 0x10
qtouch_process_info_block: Object 5 @ 0x00f2 (9) insts 1 rep_ids 0
qtouch_process_info_block: Object 6 @ 0x00fb (6) insts 1 rep_ids 1
qtouch_process_info_block: Object 38 @ 0x0101 (8) insts 1 rep_ids 0
(...)
Can it be a HW problem ?
What do you think I can do ?
Questions go in the Q&A section
CharlyBrok said:
Hi all,
I have a problem with my defy, whitout fall or update the touch screen stop responding.
After some resets & sbf flashing I've noticed that the touch screen is ok only when there is no sdcard.
I've tried over sdcards with no more success.
The sdcard is readable, I can access with adb.
Clockworkmod access the sdcard too.
With sdcard dmesg :
qtouch_force_reset: Forcing HW reset
Unable to get gpio pin num for touch_pwr_enq
touch_write: Error while trying to write 2 bytes
qtouch_set_addr: Can't send obp addr 0x 0
qtouch_process_info_block: Cannot read info object block
qtouch_ts_probe:Cannot read info block -121, checking for bootloader mode.
Without sdcard :
qtouch_force_reset: Forcing HW reset
Unable to get gpio pin num for touch_pwr_en
qtouch_process_info_block: Build version is 0x10
qtouch_process_info_block: Object 5 @ 0x00f2 (9) insts 1 rep_ids 0
qtouch_process_info_block: Object 6 @ 0x00fb (6) insts 1 rep_ids 1
qtouch_process_info_block: Object 38 @ 0x0101 (8) insts 1 rep_ids 0
(...)
Can it be a HW problem ?
What do you think I can do ?
Click to expand...
Click to collapse
AFAIK, it is HW related..
Best choice, get it to the SC..
Maybe I'll try to change the digitizer (20€ on ebay).
Warranty period is finish.
I want more log,
The goal is to enable logging debug in qtouch_obp_ts
I put in /system/etc/init.d/77debug
Echo 0xFF > /sys/module/qtouch_obp_ts/parameters/tsdebug
But no change at all...
What I am doing wrong ?
Envoyé depuis mon A500 avec Tapatalk
Hi,
I intensively searched for my problem, but found always other non-related stuff.
Recently (last 1, 2 days) my WiFi didn't connect to any APs any more. I was using CN nightlies and franco kernel, so today I did update CN without franco. Afterwards I downgraded CN and did a radio update and now I tried the stock 4.2.2 image with the flash-all script, which also seemed to reflash my radio.
The default wifi dialog always displayed the saved wifis only. And after installing stock, the initial wifi dialog displayed "searching" only for a very long time. Sometimes I see some networks and I even managed to connect to mine, but it dropped immediately.
I know, this is very undetailed, but do you have any recommendations / logs to look out / smth which could point me in the right direction? Or is my hardware just broken?
logcat outputs this when turning wi-fi on (on stock 4.2.2, unrooted):
D/WifiService( 499): setWifiEnabled: true pid=1942, uid=1000
D/BluetoothAdapter( 1942): 1110956336: getState() : mService = null. Returning STATE_OFF
W/Netd ( 156): No subsystem found in netlink event
D/NetlinkEvent( 156): Unexpected netlink message. type=0x11
W/Netd ( 156): No subsystem found in netlink event
D/NetlinkEvent( 156): Unexpected netlink message. type=0x11
D/Tethering( 499): sendTetherStateChangedBroadcast 1, 0, 0
D/Tethering( 499): InitialState.processMessage what=4
D/Tethering( 499): sendTetherStateChangedBroadcast 0, 0, 0
D/SoftapController( 156): Softap fwReload - Ok
D/CommandListener( 156): Setting iface cfg
D/CommandListener( 156): Trying to bring down wlan0
E/NetdConnector( 499): NDC Command {219 softap fwreload wlan0 STA} took too long (739ms)
I/wpa_supplicant( 9715): Successfully initialized wpa_supplicant
I/wpa_supplicant( 9715): rfkill: Cannot open RFKILL control device
I/wpa_supplicant( 9715): rfkill: Cannot open RFKILL control device
D/CommandListener( 156): Setting iface cfg
D/CommandListener( 156): Trying to bring up p2p0
D/BluetoothAdapter( 1942): 1110956336: getState() : mService = null. Returning STATE_OFF
Click to expand...
Click to collapse
when flashing stock (via the official google flash scripts), stock firmware files (qualcom, ..) are also flashed, right? or could I do something useful with the official google binaries?
Stupid post.... Ignore
Dear friends,
I have rooted nexus 7 2012, and installed PPP widget. I have configured the APN. It says "connected", but the internet is not working. Here is the PPP widget log, please help me:
PPP Widget version 1.3.3
USB_ModeSwitch log from Mon Dec 23 15:00:41 IST 2013
Raw args from udev: 2-1/2-1:1.0
Using top device dir /sys/bus/usb/devices/2-1
----------------
USB values from sysfs:
manufacturer USB Modem
product USB Modem
serial 1234567890ABCDEF
----------------
bNumConfigurations is 1 - don't check for active configuration
SCSI attributes not needed, moving on
checking config: /data/data/de.draisberghof.pppwidget/app_tmp/1c9e.f000
! matched. Reading config data
devList 1:
config: TargetVendor set to 1c9e
config: TargetProductList set to 9000,9603,9605,9607
Driver module is "option", ID path is /sys/bus/usb-serial/drivers/option1
Command to be run:
usb_modeswitch -I -W -D -s 20 -u -1 -b 2 -g 2 -v 1c9e -p f000 -f $cB
Verbose debug output of usb_modeswitch and libusb follows
(Note that some USB errors are to be expected in the process)
--------------------------------
Reading long config from command line
* usb_modeswitch: handle USB devices with multiple modes
* Version 1.2.7 (C) Josua Dietze 2012
* Based on libusb0 (0.1.12 and above)
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x1c9e
DefaultProduct= 0xf000
TargetVendor= 0x1c9e
TargetProduct= not set
TargetClass= not set
TargetProductList="9000,9603,9605,9607"
DetachStorageOnly=0
HuaweiMode=0
SierraMode=0
SonyMode=0
QisdaMode=0
QuantaMode=0
GCTMode=0
KobilMode=0
SequansMode=0
MobileActionMode=0
CiscoMode=0
BlackberryMode=0
PantechMode=0
MessageEndpoint= not set
MessageContent="55534243123456788000000080000606f50402527000000000000000000000"
NeedResponse=0
ResponseEndpoint= not set
InquireDevice disabled
Success check enabled, max. wait time 20 seconds
System integration mode enabled
Use given bus/device number: 002/002 ...
Looking for default devices ...
bus/device number matched
searching devices, found USB ID 1c9e:f000
found matching vendor ID
found matching product ID
adding device
Found device in default mode, class or configuration (1)
Skipping the check for the current configuration
Using interface number 0
Using endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: USB Modem
Product: USB Modem
Serial No.: 1234567890ABCDEF
-------------------------
Looking for active driver ...
OK, driver found; name unknown, limitation of libusb1
OK, driver "unkown" detached
Setting up communication with interface 0
Using endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Resetting response endpoint 0x81
Resetting message endpoint 0x01
Bus/dev search active, referring success check to wrapper. Bye.
ok:busdev
--------------------------------
(end of usb_modeswitch output)
Checking success of mode switch for max. 20 seconds ...
Reading attributes ...
Reading attributes ...
Mode switch has completed
Mode switching was successful, found 1c9e:9605 (USB Modem: USB Modem)
Device class of first interface is ff
Now checking for bound driver ...
Driver has bound, device is known
All done, exiting