need to exchange galaxy 10.1 but i"m worried this thing will eventually run out of batteries and my data will be accessible.
Is there a way wipe this thing in APX mode?
Thanks!
Use nvflash
command line is
nvflash --bl bootloader.bin --format_partition x (where x is the number of the partition you want to format)
partition configuration "galaxy.cfg.txt" is attached...think you would be interested in partitions 11 and 14
Tried it..
Get the following:
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x038891c541408597
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 0
sdram config strap: 0
downloading bootloader -- load address: 0x108000 entry point: 0x108000
download command failed NvError 0x120002
command failure: bootloader download failed (bad data)
bootloader status: Bct file not found (code: 21) message: flags: 1073840124
I see you are subscribed to this thread "Bricked my 10.1 I/O, all buttons dead, nvflash still working I think" so you will have seen that what I suggested you do will not work
You are just gonna have to be patient and go for the long, drawn out and exasperating battery drain game
Related
So, I attempted the process detailed at http://forum.xda-developers.com/showthread.php?t=1130574.
The output was as so:
Code:
c:\nvflash>nvflash --bl bootloader.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x03889200431fd557
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 0
sdram config strap: 0
downloading bootloader -- load address: 0x108000 entry point: 0x108000
download command failed NvError 0x120002
command failure: bootloader download failed (bad data)
bootloader status: Bct file not found (code: 21) message: flags: 1073840124
I then tried restarting my Galaxy tab, and to my surprise there is no display. I tried restarting it a couple times, and nothing changed. It is still connecting / disconnecting to my computers USB, but there is no display on it.
I was wondering how I could factory reset / resolve this problem. Any ideas?
any advance with that y have same problem
why dont you just flash to honeycomb ver3.0 using odin and then use ROM manager to install CWM? takes like 1min to do...
help! i need file bct samsung P7500 brick flash with NVflash,but error " Bct file not
hello ,i'm from Vietnammes,
i has samsung galaxy tab 10.1 P7500,I'm off to go at boot, then turn back the brick,
flash NVflash this error"C:\nvflash>nvflash --bl bootloader.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x045070c443a11297
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 17
sdram config strap: 0
downloading bootloader -- load address: 0x108000 entry point: 0x108000
download command failed NvError 0x120002
command failure: bootloader download failed (bad data)
bootloader status: Bct file not found (code: 21) message: flags: 1073840124"
\
help me,send file bct,bootloader.bin,.....
thank
Did you come right?
viet_ksxd80 said:
hello ,i'm from Vietnammes,
i has samsung galaxy tab 10.1 P7500,I'm off to go at boot, then turn back the brick,
flash NVflash this error"C:\nvflash>nvflash --bl bootloader.bin --go
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x045070c443a11297
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 17
sdram config strap: 0
downloading bootloader -- load address: 0x108000 entry point: 0x108000
download command failed NvError 0x120002
command failure: bootloader download failed (bad data)
bootloader status: Bct file not found (code: 21) message: flags: 1073840124"
\
help me,send file bct,bootloader.bin,.....
thank
Click to expand...
Click to collapse
I have 5 tablets lenovo k1, l bought them by wholesale, but my problem is that I want to resell the stock rom, and does not work the command of NVFLASH to perform a backup of the rom of one of them which is still in stock.
the data on my tablet are these:
Model name :20115
MFG date: 11/08/06
S/N CB08791734
I run NVFLASH
./nvflash --sbk 0x0d0a6f49 0x6c577634 0x4d634e55 0x47336d55 --bl bootloader.bin --go
and I get this
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x0428910141006457
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 1
file not found: bootloader.bin
command failure: bootloader download failed
How do I make my backup?
my stock rom are:
Android 3.1
Version of kernel 2.6.36.3
compilation number K1_A301_01_01_110723_SG
can anyone helpme? I ned the rom ¿anyone someone have the backup of this rom?,
This is the same tablet I am experiencing problems with adb (another thread created by me).
When I try to use nvflash, via Vega Tools ou manually, to flash a new ROM, I always receive the following error. Important information: this error I receive even before of the described problem with adb and Vega Tools.
Here is the log:
C:\Users\claroedu\AppData\Local\Temp>nvflash.exe --bct H5PS1G83EFR-S6C_V24_0625.bct --setbct --bl bootloader.bin --confi
gfile flash.cfg --odmdata 0x0b0c0075 --create --go
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 3
chip sku: 0x8
chip uid: 0x037c70c141dfc1d7
macrovision: disabled
hdcp: enabled
sbk burned: false
dk burned: false
boot device: emmc
operating mode: 3
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: H5PS1G83EFR-S6C_V24_0625.bct
- 4080/4080 bytes sent
H5PS1G83EFR-S6C_V24_0625.bct sent successfully
odm data: 0xb0c0075
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 941512/941512 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 1 0
creating partition: BCT
failed executing command 16 NvError 0x120002
command failure: create failed (bad data)
bootloader status: specified device is not the boot device (code: 17) message: nverror:0x4 (0x4) flags: 0[/B][/B]
Hi, I'm new to this forum and pretty much new to rooting/flashing tablets of any kind. I have a Acer a500 with stock rom which just broke down a couple of days ago for no reason. After much googling and searching this forum I have figured out that it is stuck in apx mode and I've tried everything I can to fix it but so far nothing has worked. Suffice it to say when I use nvflash I get this error.
C:\Users\user\Downloads\nvflash-A500>nvflash --bct bct.bct --setbct --bl bootl
oader.bin --configfile flash.cfg --odmdata 0x300d8011 --sbk 0x6b721f00 0x6447ba0
1 0x8b0e5e03 0x48dd2003 --sync
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x037c624340608197
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
odm data: 0x300d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714385/714385 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: partition table is invalid, missing required information (cod
e: 14) message: nverror:0x5 (0x1000005) flags: 0
C:\Users\user\Downloads\nvflash-A500>nvflash -r --format_partition 4
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x12
0002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
C:\Users\user\Downloads\nvflash-A500>nvflash -r --download 4 bootloader.bin
Nvflash started
[resume mode]
I assumed my partitions were corrupted so I've tried running babsector but am unable to start up in recovery mode after running a501 A.bat. I've also tried many other things but nothing has worked. Does anyone have any suggestions? I'd really appreciate any advice. Thanks!
procedure
for babsector to work you need to run A then reboot to APX mode - then run B if it shows an error than it will be a hardware failure
truthtrans said:
Hi, I'm new to this forum and pretty much new to rooting/flashing tablets of any kind. I have a Acer a500 with stock rom which just broke down a couple of days ago for no reason. After much googling and searching this forum I have figured out that it is stuck in apx mode and I've tried everything I can to fix it but so far nothing has worked. Suffice it to say when I use nvflash I get this error.
C:\Users\user\Downloads\nvflash-A500>nvflash --bct bct.bct --setbct --bl bootl
oader.bin --configfile flash.cfg --odmdata 0x300d8011 --sbk 0x6b721f00 0x6447ba0
1 0x8b0e5e03 0x48dd2003 --sync
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x037c624340608197
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: bct.bct
- 4080/4080 bytes sent
bct.bct sent successfully
odm data: 0x300d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714385/714385 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
failed executing command 25 NvError 0x120002
command failure: sync failed (bad data)
bootloader status: partition table is invalid, missing required information (cod
e: 14) message: nverror:0x5 (0x1000005) flags: 0
C:\Users\user\Downloads\nvflash-A500>nvflash -r --format_partition 4
Nvflash started
[resume mode]
Formatting partition 4 please wait.. Command Execution failed cmd 13, error 0x12
0002
FAILED!
command failure: format partition failed (bad command)
bootloader status: unknown operation (code: 1) message: flags: 0
C:\Users\user\Downloads\nvflash-A500>nvflash -r --download 4 bootloader.bin
Nvflash started
[resume mode]
I assumed my partitions were corrupted so I've tried running babsector but am unable to start up in recovery mode after running a501 A.bat. I've also tried many other things but nothing has worked. Does anyone have any suggestions? I'd really appreciate any advice. Thanks!
Click to expand...
Click to collapse
freightyard said:
for babsector to work you need to run A then reboot to APX mode - then run B if it shows an error than it will be a hardware failure
Click to expand...
Click to collapse
Thanks for replying. I ran A first and these were the results....
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x037c624340608197
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: flash.bct
- 4080/4080 bytes sent
flash.bct sent successfully
odm data: 0xb00d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714409/714409 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
command failure: create failed (bad data)
bootloader status: failed to create the partition (code: 10) message: nverror:0x
5 (0x1000005) flags: 0
Press any key to continue . . .
Then I shut down and restarted again....still in apx mode...and ran B...
Nvflash started
rcm version 0X20001
System Information:
chip name: t20
chip id: 0x20 major: 1 minor: 4
chip sku: 0x8
chip uid: 0x037c624340608197
macrovision: disabled
hdcp: enabled
sbk burned: true
dk burned: true
boot device: emmc
operating mode: 4
device config strap: 0
device config fuse: 0
sdram config strap: 0
sending file: flash.bct
- 4080/4080 bytes sent
flash.bct sent successfully
odm data: 0xb00d8011
downloading bootloader -- load address: 0x108000 entry point: 0x108000
sending file: bootloader.bin
| 714409/714409 bytes sent
bootloader.bin sent successfully
waiting for bootloader to initialize
bootloader downloaded successfully
setting device: 2 3
creating partition: BCT
failed executing command 16 NvError 0x120002
command failure: create failed (bad data)
bootloader status: failed to create the partition (code: 10) message: nverror:0x
5 (0x1000005) flags: 0
Press any key to continue . . .
Just wanted to note that when I tried to flash using blackthund3rs apx flash tool my tablet shows a green acer logo in the middle of the screen and in the top left it says something like entering apx mode, but when I run the babsecter it has the normal white acer logo in the middle of the screen and in the top left it says entering acer download mode. Don't know if that is pertinent or not but just thought I'd mention it.
So from the results above does it sound like my tablet is just not going to be revived? Is it a hardware failure for sure?
hardware
looks like it
you could reflow the board just do a search in forum on reflowing for procedure