For all you Repair guys,
How do you re-assemble the volume up down key without damaging the buttons on the flex board.
Do you attach the back housing then insert the volume key?
Or it has to be done with both back housing and volume key at time of assembly?
hints tips please
In for an answer
This is driving me crazy as well! Has anyone figured it out? I get it in there and som,etimes volume up will work, but not volume down. The official HTC video doesn't show how to do it exactly. It does show the volume key being in there when they put the chassis back in the plastic shell part though.
I just repaired another hd2 I installed both the volume key and housing at same time and worked, It didn't distroy the tiny buttons on flex this time.
JUst go slow and do not force it
use some tape to hold the volume button in the housing while you install the chassis / screen into it.
Vol keys button installs just before u put backside,put button and align,then CAREFULLY put backside and snap on.find best angle that buttton holds himself in normal position then snap....
Sent from my Milestone using Tapatalk
Related
i just bought a used Droid incredible and i have had it for about 3 days and i have noticed something about the power button at the top. the power button doesnt "click" when pushed down like the volume buttons do at the side, it just goes down. its kind of annoying is there a way to fix it or something? are of them like this or is it just mine? if you have a droid incredible can you tell me if the power button clicks like the volume buttons do when you press it or does it stick like mine?
The power button does feel like the clicks in the volume buttons.
whenever my phone comes in contact with a lot of sand, the power button gets mushy like that. yes its supposed to click like the volume buttons. try cleaning it out and see if it helps
what do i do to clean it out? also is there a way i cant just remove the 4 screws on the back open up my phone and clean the power button from there? i think that would be easier because i can make sure there is nothing stuck down there. but the only problem is the VOID warranty sticket is on one of the screws and i dont want my warrenty to be voided because i just bought this phone.
so does anyone know how i should remove that sticker and put it back on the phone without ruining it?
You can use an exacto knife to peel it off, the topic is in here somewhere
Sent from my HTC Incredible
Hello. I replaced the touchscreen.
when I switched. always up sound.
button is not pressed.
when they involve no housing. everything works.
when inserted into the housing problem
I dont really understand what your trying to say.. but if its what I think, then the housing you are using is either pressing on the up key and cuasing the volume to be 100% all the time, or the housing is incorrectly placed. Try taking the housing off and reapplying it.
When I wore body. volume itself increases.
When I turned it on without a body it is not happening.
I think that the body where it presses. but not on the button.
I collected body without buttons sound.
what my mistake???
Hey, i just replace my digitizer for my t-mobile hd2 and successful got it back together and thought that everything was work, but i could not get the volume button in. I got it in after putting the chassis on but the volume button still doesn't work. So if anybody could give me some input on this that would be very helpful.
Do you feel the button take action when you press it? If it does, then the contact is made with the button, the problem might be something else.
a guy from HTC repair said its better to change whole screen instead of replacing digitizer.
As mentioned, can you feel the button depressing when you add pressure to the rocker? Pull the case back off and press the button manually to see if it works when powered on. If it works then, realign the flex cable and retry. If it still doesn't work, then you most likely damaged the flex cable and need to replace it.
connexion2005 said:
As mentioned, can you feel the button depressing when you add pressure to the rocker? Pull the case back off and press the button manually to see if it works when powered on. If it works then, realign the flex cable and retry. If it still doesn't work, then you most likely damaged the flex cable and need to replace it.
Click to expand...
Click to collapse
In addition to said above check housing screws, they must be tightened because if they are missing plastic volume keyboard will misalign with flex cable volume keys and it will be impossible to press them.
pvii said:
In addition to said above check housing screws, they must be tightened because if they are missing plastic volume keyboard will misalign with flex cable volume keys and it will be impossible to press them.
Click to expand...
Click to collapse
At first i forgot to put back the last 4 screws so the housing was not on tight enough but i now i did that and its still not working. So now im going to try look over the flex cables again and hope that will works.
connexion2005 said:
As mentioned, can you feel the button depressing when you add pressure to the rocker? Pull the case back off and press the button manually to see if it works when powered on. If it works then, realign the flex cable and retry. If it still doesn't work, then you most likely damaged the flex cable and need to replace it.
Click to expand...
Click to collapse
After disassembly i found out that the flex cable for the volume button was damaged (probably while trying to put the volume button in) and i have to figure out where i can get a new one but Thanks everyone for there time and help.
jacks3jd said:
After disassembly i found out that the flex cable for the volume button was damaged (probably while trying to put the volume button in) and i have to figure out where i can get a new one but Thanks everyone for there time and help.
Click to expand...
Click to collapse
It can be found on eBay for about 43-44 bucks. Good luck!
usualy i am good with physical problems like this but i am now forced to make my own thread because i have no idea why my device wont power on.
after opening my blackstone/touch hd to tighten my screws, my power button has stopped working.
(fyi, a screw came loose a while ago near my sim card after dropping my devive so i thought id tighten all my screws while i had my screwdrivers out fixing my cousins phone)
however, without having the plastic power button attatched to the device, i am able to press the actual button with my stylus and make contact with the main button on the motherboard, the device will now power on.
(eliminating that the actual button to power on is broken)
but, when i attatch the plastic button and press it to power on the device, it doesnt make contact with the actual button inside on the motherboard.
(not making contact with the button on the motherboard)
i have examined the plastic button, all is intact and i am assembling it to the device correctly.
i have examined the actual power button on the motherboard and that is working perfect.
what the hell is going on?
thanks
Rn
ps, i need my power button
cba putting my stylus in and taking it out whenever my backlight goes off
* if you want a picture of my plastic button, i will dissasemble my device and take a picture.
Pictures ?
Wow guys, talk about cheap hardware.
My volume up key is sunken down in so far that I can't press it. Volume down worked, until I just pressed it down again and the whole button is subsurface. Yay.
Here's a photo with the volume up side stuck below.
I'll try to pop it out with a screwdriver.
Update:
I removed the rear case all the way, then pushed the buttons into the case, using duct tape to keep them from falling out. Then I snapped the case back on.
Here are photos. One shows the buttons, and the other is of the tablet internals, in case anyone wanted to see...