Hard Bricked my phone - Atrix 4G General

I already posted this in Q&A, but I thought it would get noticed more in this section.
Ok I believe my phone is "Hard Bricked", because it doesn't power up at all. The Green led light will show if i take the battery out and plug it into the computer. This happened as was trying to start the process to unlock my bootloader. I was using RSDlite, loading the "zomgunlock" sbf file, put my phone into rsd mode plugged it in, pressed start and next thing i know it turned off and won't turn back on. Can someone help me?

ninjajtm said:
I already posted this in Q&A, but I thought it would get noticed more in this section.
Ok I believe my phone is "Hard Bricked", because it doesn't power up at all. The Green led light will show if i take the battery out and plug it into the computer. This happened as was trying to start the process to unlock my bootloader. I was using RSDlite, loading the "zomgunlock" sbf file, put my phone into rsd mode plugged it in, pressed start and next thing i know it turned off and won't turn back on. Can someone help me?
Click to expand...
Click to collapse
What version are you on? And can you boot in rsd?
Sent from my MB860 using XDA App

its version before 4.1.83, but i know i can't get to RSD or to get something showing on the screen

Was it low on charge?
Sent from my MB860 using XDA App

No its not from a low charge, it was on already 80%

Oh, does your phone get recognized when plugged into a cp?
Sent from my MB860 using XDA App

no it doesn't seem to be recognized, i tried doing the combos green led light on (volume up + power , etc.)

But the phone stays off?
Sent from my MB860 using XDA App

It stays off unless I take the battery out of the phone and hook it to the computer, that is when I get the green light indicator

Hi,
I am a NOOB but was reading another post that had a similar problem. Not sure how to make a link to it.
The issue the other fellow had was that when he plugged in to the USB port it was actually draining his battery rather than charging it.
There are specific drivers on the Moto website that you need for the computer to charge the phone.
The short way around it is to charge at the wall.
The title of the post I am referencing is "[SOLVED] Atrix will not power on, green light flashes, plugged in and.... nothing!" initially posted 24th Feb 2011 last post was today.
If your issue is more complicated than this then I apologise for wasting your time.
Worst case no further harm done.

I'm pretty sure my battery is pretty good atm but I'll try anything to get my atrix working again

That happened to me when I was trying to flash the unlock bootloader for mine. I'm using the Atrix on Orange running on U4_4.2.0. Completely bricked with the same green light but nothing happening. Told Orange and got a new one luckyly, next day!

Yea well im on my second from at&t bcuz of a hardware problem, unless I'm able to get a third one. .i ned to find out how to fix this, and the battery charger method didn't work for me

Sydpark said:
Hi,
I am a NOOB but was reading another post that had a similar problem. Not sure how to make a link to it.
The issue the other fellow had was that when he plugged in to the USB port it was actually draining his battery rather than charging it.
There are specific drivers on the Moto website that you need for the computer to charge the phone.
The short way around it is to charge at the wall.
The title of the post I am referencing is "[SOLVED] Atrix will not power on, green light flashes, plugged in and.... nothing!" initially posted 24th Feb 2011 last post was today.
If your issue is more complicated than this then I apologise for wasting your time.
Worst case no further harm done.
Click to expand...
Click to collapse
USB port on a computer won't drain a connected device. Problem there was he was trying to charge a drained battery on USB 2.0 which doesn't supply enough power to charge properly. The solution to his problem was to charge with the proper Motorola AC wall charger.

Yea I know but I tried the fixes anyway since there was no harm

If it's an AT&T phone take it to a repair center and they will replace it if its less than 1 year old. You don't even need the crappy insurance.

I thought it's only me
I have same problem, googled it 2 days ago - noboday else reported it
same problem - flashed the unlock-able boot-loader - phone turn off, and died...
I progressed a bit more - after replacing battery with a fully charged one, just to find out it's not a battery issue - I prepared the "special cable" - pin 4 connected to VCC.
now - my phone does recognize my phone, as "APX". after providing drivers found in google - it now recognized as "NVIDIA USB Boot-recovery driver for mobile devices".
it doesn't really help, as RSDlite is still not recognizing it, and using NVflash - i get only errors...
I know - i didn't really helped to solve the problem, as I'm "stuck" with it too, just wanted to share my effort...
Tomer

henrys01 said:
If it's an AT&T phone take it to a repair center and they will replace it if its less than 1 year old. You don't even need the crappy insurance.
Click to expand...
Click to collapse
Even though this is my second phone?

ninjajtm said:
Even though this is my second phone?
Click to expand...
Click to collapse
The phone has a 1 year manufactures warranty.

o ok, thanks for letting me know

Related

officially bricked

I tried to load up the new gingerbread roms from my current one. I downloaded its content and tried to install it via clockwork.
I first deleted system, logo, and cache followed up by a restore format. When trying to download the new rom, I was getting a weird error that was stopping me from completing the full installation. So basically was in a chokehold because I didn't have any backup files or another working rom in the sd at that time. I just restarted the phone and it for a few times was stuck on the M screen, but now its just green led when I plug it into the computer usb. When plugging it into the outlet, it imediately turns on stuck on the M screen and shuts off when unplugging as if the battery isnt charging at all.
Sounds like ur going to have to sbf.
Sent from my DROIDX using XDA App
bigshotrob22 said:
Sounds like ur going to have to sbf.
Sent from my DROIDX using XDA App
Click to expand...
Click to collapse
thats the problem.. i got the X.340 sbf and the program aswell but I cant get into bootloader mode. is there an alternative way to sbf?
Did u pull the battery for 30 seconds and then hold the volume buttons + power to put it n bootloader
Sent from my DROIDX using XDA App
Could be your battery same thing happened to me try using a friends battery your battery could be dead and it no longer charges
Sent from my DROIDX using XDA App
bigshotrob22 said:
Did u pull the battery for 30 seconds and then hold the volume buttons + power to put it n bootloader
Sent from my DROIDX using XDA App
Click to expand...
Click to collapse
bootloader is such a rare occurance for me, i just had it come out but it was flashing low battery. the thing is, im not quite sure if its charging if i have it plugged into the computer. when i have it plugged into an outlet, the M splash screen comes up so i'm worried that draining the power..
edit: now it flickers for a split second, am i supposed to hold on to it til something shows up? been like 1 minute
i dont think bricking phone blows your battery. at least i hope it doesnt, was working fine before.
Plug it in without the battery if a question mark comes up you ned to use another battery cuz it won't charge in boot loader and the boot loader should pop up right away hold power volume down and camera button it takes about three seconds
swyped from my DROIDX using XDA App
well its basically the same thing. when plug into the outlet it shows the m splash screen with or without the battery.
when its plugged into the compuiter however, its just flickers once. when it is done with the battery in, the led is on forever
EDIT: OBSERVATION
when on the wall, it is actually charging, but REALLY slowly because of the fact that the splash screen stays on. found this out because i had it in for30 min and then tried to connect mit to my comp with bootload and it loaded for a few minutes with the low battery flashing.
is version 320 the latest?
Okay. so it isnt charging as I though because its not working at all... problem is, I dont know if it truly is a battery defect. If I were to Buy a new battery, how would i know if it is charging if it doesnt boot and just stays stuck on the M logo screen?
perhaps I should by a battery charger where i take the battery out and charge it through there? because my bootloader always gives me the same low battery.
Do you have any friends with the same phone? There is also a macgyver (spelling?) Method of doing this by cutting the USB cable open and attaching the cable ends to the battery. However I would only do this if you're really desperate
i just really need make complete sure that this phone is INFACT dead battery
when not plug, it doesnt turn on what so ever with a white spark on the led.
when plugged nto outlet the logo shows but i isnt charging because it isnt booting
when plugged into the computer it is a solid green which i think represent a dead or a low battery state(can someone back thisup?)
Your battery is dead, as in drained, but should work fine once you get your phone to a bootable state again. The problem is that, in the state your phone is in, there's no charging capabilities. Bootloader won't do it, neither will sitting at the M logo. So, you just need to find someone with a compatible battery to let you use it to SBF your phone. Then, boot the phone up completely, and let your battery charge to at least 50-60% before trying to install a ROM. Preferably, I'd go with a full charge, just in case you end up in a similar situation again.
This is nothing to freak out over, you'll be fine.. the only problem you have is that your battery has no juice, as confirmed by the low battery warning in the bootloader, when you successfully got it to load.
raziel36 said:
Your battery is dead, as in drained, but should work fine once you get your phone to a bootable state again. The problem is that, in the state your phone is in, there's no charging capabilities. Bootloader won't do it, neither will sitting at the M logo. So, you just need to find someone with a compatible battery to let you use it to SBF your phone. Then, boot the phone up completely, and let your battery charge to at least 50-60% before trying to install a ROM. Preferably, I'd go with a full charge, just in case you end up in a similar situation again.
This is nothing to freak out over, you'll be fine.. the only problem you have is that your battery has no juice, as confirmed by the low battery warning in the bootloader, when you successfully got it to load.
Click to expand...
Click to collapse
thanks for the reassuring comment, however, i think i need to bootload.
i accidently did the partition hat formats everything.. cant recall if it was under clockwork because it didnt have the same interface, i was all light blue text with an ok button on the left corner. Anyway, i've completely destroyed the phone as in no roms no factory.
can I possibly get a dock to charge this battery and then get into bootloader for an sbf session
? Even if I did have battery, im pretty sure i just hover at the logo screen
jinho11050 said:
thanks for the reassuring comment, however, i think i need to bootload.
i accidently did the partition hat formats everything.. cant recall if it was under clockwork because it didnt have the same interface, i was all light blue text with an ok button on the left corner. Anyway, i've completely destroyed the phone as in no roms no factory.
can I possibly get a dock to charge this battery and then get into bootloader for an sbf session
? Even if I did have battery, im pretty sure i just hover at the logo screen
Click to expand...
Click to collapse
There's a usb trick u can try. Google it.
Sent from my DROIDX using XDA App
jinho11050 said:
thanks for the reassuring comment, however, i think i need to bootload.
i accidently did the partition hat formats everything.. cant recall if it was under clockwork because it didnt have the same interface, i was all light blue text with an ok button on the left corner. Anyway, i've completely destroyed the phone as in no roms no factory.
can I possibly get a dock to charge this battery and then get into bootloader for an sbf session
? Even if I did have battery, im pretty sure i just hover at the logo screen
Click to expand...
Click to collapse
You definitely need to use the bootloader, and I was implying that in the first reply(SBF'ing requires going into the bootloader). If you had a stand-alone battery charging cradle/dock, that should do the trick. Just make sure to let the battery charge sufficiently. I've successfully gotten an SBF completed, starting with only 30% battery. SBF takes about 7 minutes on my laptop(not that I've timed it, but I usually light up a smoke when I start the process lol). So, as long as the battery is charged enough to no longer give the "Low Battery" warning in the bootloader, you should be fine.
You got your usb cable and put the ends where the battery goes that's how I got mine working try it
Sent from my DROIDX using XDA App
froyli said:
You got your usb cable and put the ends where the battery goes that's how I got mine working try it
Sent from my DROIDX using XDA App
Click to expand...
Click to collapse
al the tips or just red for pos and black for neg
Positive and negative google it before you do it
Sent from my DROIDX using XDA App
okay im having another issue with bootloader.. the program detecs it but i canot start the process.. am i missing something?
EDIT: finally got sbf working after renaming it.
All my threads have been in a form of technique difficulty question and the answer I get from the community were VERY helpful. thank you everyone
jinho11050 said:
okay im having another issue with bootloader.. the program detecs it but i canot start the process.. am i missing something?
EDIT: finally got sbf working after renaming it.
All my threads have been in a form of technique difficulty question and the answer I get from the community were VERY helpful. thank you everyone
Click to expand...
Click to collapse
Glad you got it working! Nearly everyone on here has needed help, at one point or another, and that's what makes Android so great... the community.
Sent from my DROIDX using XDA App

Atrix wont charge!

Hi im running alien 4 and im unlocked, my ATRIX wont charge through the pc usb or through the stock moto wall charger.. I tried using a different micro usb cable to no avail but if I turn the phone off and plug it in, the green led turns on and the phone starts.. I even have 2 batteries and neither work
EDIT* I just tried using my dads phone wall charger and that didn't work either
Your usb port might be borked, or worse the power supply inside phone is jacked. If you don't find a solution soon then I would think about warrantying the.phone.
I voided my warranty.
Can adb, fastboot or rsd recognize your phone?
Sent from my MB860 using xda premium
Try turning the phone off and then as you plug it in hit the power button and let the phone boot. Will it charge then? I had this problem and ended up having to flash the full Pudding SBF to resolve the issue.
pukemon said:
Your usb port might be borked, or worse the power supply inside phone is jacked. If you don't find a solution soon then I would think about warrantying the.phone.
I voided my warranty.
Click to expand...
Click to collapse
Hey, come on. Fix or get rid of that signature. I've seen tons of people get confused from your posts because you don't have a separating line or anything. And sometimes it (weirdly) goes along with posts and messes everyone up. It's just been bugging the piss out of me...

[Q] MB526 won't charge via USB, white LED on

I flashed my Defy with a custom ROM months ago and never had a problem. I left my phone for a few days and it's completely drained of its battery. I try to charge it using my USB cable connected to my PC, but the Defy doesn't show the animation where the battery is shown being charged; just the white LED and a black screen. When I hit the power button, it shows "bootloader 09.10, battery low cannot program". I know I flashed my phone correctly and have no idea why this screen is being shown. I didn't try to charge via wall outlet, I'm currently on vacation and only brought the USB cable with me. Any help would be greatly appreciated!
Edit: My phone is a regular MB525, flashed with with a custom Gingerbread that was posted in this very forum. On my PC the model reads MB526...
Once battery is fully drained occassionally Defy takes time to even boot up. So leave it in that state (Connected to USB ) for couple of hours and try again.
Tried and didn't work, I'm hoping plugging into the AC charger will fix this...though that won't be happening for another week..
Have you the possibility to try the battery in another defy or to use another battery?
Not until about a week..
Don't worry, your Defy will get charged when connected to wall plug.
Mine was the same situation as it won't charge on total empty battery over USB port.
But it charging normally as soon as I plug it to wall charger.
just make sure you don't flash it with any SBF!
OP! i had exact same problem and it snowballed into something huge. It started same as you did, my fone ran out of juice as I was in my office and I couldn't get USB port to charge it, all I had was white LED and black screen in my office. So, at home i plugged it into wall charger for 5 or more hours and I still couldn't see the battery that shows its charging, I tried a different wall charger and still same results.
Then my phone begin to atleast fired up in wall charger but got stuck in Moto M logo. I could only access bootloader and not the Boot recovery for some reason. I been stuck here since, my battery was fully charged externally and yet nothing, I even tried every combo (SIM in, SIM out, SD Card in, SD Card Out) etc but I couldn't get into boot recovery so I could just hard reset my Defy. I could only access the bootloader.
At that point I flashed by Defy with 2.1 SBF's like 7 of them with same results, no matter what SBF file I successfully flashed with I could for the life of me get into boot recovery.
Now, i am just sick and tired and hate Defy because its effed up. I am taking it to the shop i purchased it from tomorrow.
i guess im having almost the same problem.
my defy doesnt boot, only shows the white LED.
it is recognised by the RSD, but nothing happens.
cant boot, doesnt show anything on the screen.
what should I do?
macgyver is not working either
I had a similar issue and I used the macgyver trick and flashed a new sbf. The rom you are using possibly doesn't support charging in the off state.
Sent from my CM9 Defy
as a total android/motorola user
and i appear to be having the same issue, bootloader only!!
Could i ask what and where is the official unmodified rom for this phone.
Thank you.
Cornz
---------- Post added at 02:10 PM ---------- Previous post was at 01:43 PM ----------
Meant to put "beginner" or "newbi" or "noob"...
I am somewhat pleased to report that a mains powered charger seems to be charging the phone...
Did the mains powered battery charger solved your problem?
I have to fix my girlfriend phone that seems to have the same issue.
Could you post the model or a link to the model of battery charger you have used?
effepas said:
Did the mains powered battery charger solved your problem?
I have to fix my girlfriend phone that seems to have the same issue.
Could you post the model or a link to the model of battery charger you have used?
Click to expand...
Click to collapse
It was a standard mains charger.......Cheapo from the market...
cornz said:
It was a standard mains charger.......Cheapo from the market...
Click to expand...
Click to collapse
Thank you for your help.
Unfortunately that solution didn't fix the battery problem... and also the McGyver method didn't work.
I'm afraid that my girlfriend will need a new battery.
She was using an aged MIUI rom (more or less six months old). After the battery replacement should I have to flash the stock Froyo CEE rom via RSD or do you think that the will works again?
Did u fixed the problem ? How ?
I`m in same posture...
I'm still in the same situation. The battery is on stuck at 5%, even if I change the one I own with another one. I can't flash via RSD and I don't know how to fix this problem.
Sent from my GT-I9300 using xda app-developers app
effepas said:
I'm still in the same situation. The battery is on stuck at 5%, even if I change the one I own with another one. I can't flash via RSD and I don't know how to fix this problem.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Are you SURE the macgyver hack was done right? Did you use a usb port of a powered usb hub????
Sorry to ask but getting the wires to hold in place was difficult and if the usb port cant provide enough power then the macgyver hack wont work IME....
cornz said:
Are you SURE the macgyver hack was done right? Did you use a usb port of a powered usb hub????
Sorry to ask but getting the wires to hold in place was difficult and if the usb port cant provide enough power then the macgyver hack wont work IME....
Click to expand...
Click to collapse
Sorry for the delay, buddy, I tried a different times and I asked also to another friend to try, as double control, but it didn't work.
Actually I send the phone to the assistance center... and I'm keeping my finger crossed.
effepas said:
Sorry for the delay, buddy, I tried a different times and I asked also to another friend to try, as double control, but it didn't work.
Actually I send the phone to the assistance center... and I'm keeping my finger crossed.
Click to expand...
Click to collapse
Damn, that's a shame...Hopefully its just a corrupt rom, the new boot loader is brick-proof I believe.
I rooted mine after upgrading and its a cracking little android phone...Actually, it doesn't get used as a phone, but a portable computer/gps.

[Q] mt4g flashing LED no vibrate no screen

Hey guys, Im trying to fix this mt4g for a friend.. It wont boot, I cant get into hboot or recovery, all it does is flash the LED. I have read post saying its because I was unsuccessful at loading bootloader, however it doesn't vibrate like the others are saying. I left the battery out for a couple hours along with sd and sim, also tried charging through the night... I cannot figure this one out, also, the computer will not recognize any new hardware or drivers. Is this phone bricked beyond repair?
I put the battery on my battery charger and let the battery charge outside of the phone now when I put the battery in the phone and plug it in to the computer, the red LED comes on and stays on, along with a red glow on the trackpad... Anyone know what to do?
Blinking LED is either the battery is charging to at least one percent, or you didn't press the right button combo to boot into bootloader. Power + Volume Down is bootloader, Volume up will give you three vibrates and a flashing LED, where you will have to pull your battery.
Thanks, I cant get the phone to do anything... I plug it in with the battery in, without pushing any buttons and the LED comes on and the IR trackpad light comes on... It wont respond to anything, no drivers popup.. Is there anyway to recover a bricked mt4g? Im new to it, as I have an Evo and have never had anything like this occur with all the evos i've flashed and rooted... If someone knows anyway to fix this feel free to give input..
Thanks everyone!
ya .. mine is doing the samething.
I just try to turn it on and I get one vibrate ... nothing else
I hit down and power and I get one vibrate .. nothing else
I hit up and power I get 3 fast vibrates and a flashing orange led ... I try to plug the USB here and I get 3 fast beeps on the comp
I hit up and down vol and power I get 5 fast vibrates with a solid green led and noting else... usb again beeps 3 times on the comp
neither will recognize the usb and I have reinstalled the drivers .. and of course none will work with adb either.
I think we are screwed really ... but maybe someone knows something i dont on this here. Thanks for any help.
if you fix your phone. let me know
dragon_usa said:
if you fix your phone. let me know
Click to expand...
Click to collapse
ya .. no luck so far ..I have tried a lot .. different drivers .. HTC sync .. etc.
I have tried different button pushes .. usb ports .. wont work in adb .. nothing is doing anything.
all I hear thru my speakers when I plug it in is that damn the fast 3 beeps .. ike a "hell no go F yourself you arent connecting it"
and there isnt a lot of info online bout this .. other than some others have the same LED blinking and stuff .. I still dont know what the different LED modes mean.
so IM screwed .. BUT I am getting an LG G2X as an alternate exchange thru T-Mobile warranty though. goodbye mytouch 4G Hello to G2X AND Galaxy S II(bought) .. fun times!
I found a thread somewhere, not sure where but it said that if you cant get anything and the infra-red on the touch sensor is lit the phone is completely bricked!
Its not bricked. Somethign is wacky with the phone, mine has done it and thats why im trying to find out what the hell is going on. My phone acts like its completely dead. This post migt end up being really long.
Ok, i notices this, i used my phone as a wifi hot spot. Turned it off. Left my phone alone, i then put it on charge and went to sleep. Woke up looked at the battery, no color other than the lighting bolt. Unplugged it then went off. Pluged charger back in and orange led flashes. Tried to get into recovery nothing. Tried to power it on, nothing, tried the volume down and power, three vibrations. Ok then i decided to take out the battery in and out, didnt work, tried leaving the battery out for a few minutes, then put it back in, same. Took out memory card, sim card. Then plugged in the charger. Let it sit for awhile then it works. I notice if you dont use the orginal charger that may also be the problem. I dont have my orginal but i used a walmart charger and seems like a super charger and some how charged my battery enough to be booted up, i daily use a charger that i found with the same connection x-( , that could be the problem. I dunno what makes this happen but it happened to me at least three times. I kinda figure the battery or the emmc chip is involved, could be the hotspot, could be anything, but we dont have enough evidence to figure it out, ill try to post what my battery usage on here. I use cm7 and it only happens when i use it. I tried all other roms but no repeats. That was my story.
Sent from my GT-P7510 using xda premium
Sent from my GT-P7510 using xda premium
Strapt said:
ya .. mine is doing the samething.
I just try to turn it on and I get one vibrate ... nothing else
I hit down and power and I get one vibrate .. nothing else
I hit up and power I get 3 fast vibrates and a flashing orange led ... I try to plug the USB here and I get 3 fast beeps on the comp
I hit up and down vol and power I get 5 fast vibrates with a solid green led and noting else... usb again beeps 3 times on the comp
neither will recognize the usb and I have reinstalled the drivers .. and of course none will work with adb either.
I think we are screwed really ... but maybe someone knows something i dont on this here. Thanks for any help.
Click to expand...
Click to collapse
I have done all these as well, and still unable to get past the black screen, or acheive bootloader as well. I have even left the battery out for a couple of hours, and still no different. Going to try recharging the battery once more, and some other things.
As for adb it is of no help as of now. I keep getting an error saying no device found. Has anyone found a way past this yet, to try rebooting through adb?
*Edit*
After trying to replace files on the sdcard I was not able to get past this issue. Also spoke with tech support, and was not able to get anywhere with their help. After speaking with them, I have come to conclusion the is bricked. I still cannot figure out what caused the phone to do this I broke down and sending it out to be replaced. Thankfully I have the insurance so I don't have to pay anything for the replacement.
Apparently its not bricked cause I'm still using mine. Try a different charger probly a stronger one like walmarts. I think the battery has a fart and is messed up for a little when it doesn't have a good charge
Sent from my HTC Glacier using xda premium
tnt8902 said:
Apparently its not bricked cause I'm still using mine. Try a different charger probly a stronger one like walmarts. I think the battery has a fart and is messed up for a little when it doesn't have a good charge
Sent from my HTC Glacier using xda premium
Click to expand...
Click to collapse
I have done this, fully charged it twice, and no change for me. I am glad it worked out for you.
Its not bricked.
Download the stock rom, and put that .zip in the root of your SD card. Put it in, press Power + Volume DOWN and wait for the bootloader. Once it boots, it should recognize the .zip and ask if you want to update it, run the update and your phone will be at stock again. Then root again, install Clockwork, and hopefully you backed up your ROM. This won't effect S-OFF, but you will have to run VisionARY again to get root permissions to run clockwork.
Hope this Helps.
one more
I am too having this problem
just blink orange
can't access bootloader or any else....
I too had this problem not too long ago. My power button wouldn't work though... I just connected via USB to my computer with the battery out, put it back in while connected and it turned on. Maybe I'm just lucky but give it a try
Sent from my HTC Glacier using XDA

bricked? red flashing led

Just got my nexus 4, and after it was left in cwm for about 10 minutes (while I was making breakfast) it went to a black screen and now just the red led notification led is flashing whenever plugged in, and on my mac in system profiler it shows "composite device", any suggestions?
Thanks!
nycbjr said:
Just got my nexus 4, and after it was left in cwm for about 10 minutes (while I was making breakfast) it went to a black screen and now just the red led notification led is flashing whenever plugged in, and on my mac in system profiler it shows "composite device", any suggestions?
Thanks!
Click to expand...
Click to collapse
Is your device hot to the touch?
Sent from my Nexus 4 using xda premium
20 second press on power button
No luck
Sent from my HTC One X using xda premium
Don't know if you want to do this, but you can open the phone and disconnect and reconnect the battery connector...
What was your battery level, I know in other devices some times the CPU(s) run at full speed in recovery allowing for quicker flashing this could discharge the battery rapidly. Also a flashing red LED when plugged in normally means the phone is charging but doesn't have enough charge to reliably turn on, leave it plugged in for about 15 minutes and try turning it on again.
Try holding down the VOL + and - keys along with the powerbutton (after turning it off by holding down the power button for an extended time) and see if you can get into fastboot. My friend's Nexus 4 kept bootlooping after he unlocked the bootloader but booted straight to CWM after, not letting it erase userdata first.
Net.silb said:
Don't know if you want to do this, but you can open the phone and disconnect and reconnect the battery connector...
Click to expand...
Click to collapse
I have no problem doing this, the phone seems easy to disassemble, looks alot like a overgrown iPhone 4, 2 screws on the bottom. I just hope its an easy slide, I don;t want to mar it in case I have to exchange it.
jakejm79 said:
What was your battery level, I know in other devices some times the CPU(s) run at full speed in recovery allowing for quicker flashing this could discharge the battery rapidly. Also a flashing red LED when plugged in normally means the phone is charging but doesn't have enough charge to reliably turn on, leave it plugged in for about 15 minutes and try turning it on again.
Click to expand...
Click to collapse
I thought this as well, its been plugged in for at least an hour now.
Oh and now I don't even get the red led!
good times..
I've got the exact same issue. Plugged it in last night to charge and this morning it wouldn't turn on. Plugged and unplugged it and the red LED starts flashing. After a minute or so I'm getting the battery charge animation on the screen - so the red LED is power related. Now to see if it actually charges up and boots.
Hi nycbjr. I have seen a similar issue posted here, but I can't find the thread at the moment, try searching. If I remember correctly then he got it working by holding power, volume keys and then plugging in the charger.
nycbjr said:
I have no problem doing this, the phone seems easy to disassemble, looks alot like a overgrown iPhone 4, 2 screws on the bottom. I just hope its an easy slide, I don;t want to mar it in case I have to exchange it.
I thought this as well, its been plugged in for at least an hour now.
Oh and now I don't even get the red led!
good times..
Click to expand...
Click to collapse
Try a different charger?
Unlucky
Get a Free £5 On a GiffGaff sim
Called google, they are sending me another one advanced replacement, so I can send the bad one back at me leisure.
Good customer service!
Qhsusb_dload
nycbjr said:
Called google, they are sending me another one advanced replacement, so I can send the bad one back at me leisure.
Good customer service!
Click to expand...
Click to collapse
Hi!! I have the exact same problem, unfortunately the phone is bricked! Does anyone know how to fix this? I saw a video on youtube Nexus 4 - JTAG Brick Repair Service
CalogeroIndorato said:
Hi!! I have the exact same problem, unfortunately the phone is bricked! Does anyone know how to fix this? I saw a video on youtube Nexus 4 - JTAG Brick Repair Service
Click to expand...
Click to collapse
If u are fully bricked JTAG is the way to go.
Sent from my Nexus 4 using Xparent BlueTapatalk 2
Here seems to be a similar thread, maybe you'll find help there.
http://forum.xda-developers.com/showthread.php?t=2111947

Categories

Resources