Related
So all i want to do is take everything off my 4gb sd card and use an 8gb sd card so that I have more storage space. Everything works great as is, and I wanted to keep everything as is. Just need more storage space. I've looked through the forums and haven't found anything that addresses this process. I am running CyanogenMod 7.0.3 w/a 4gb sandisk micro sd card. How do I copy so that it boots just like my 4gb card???? Thanks ahead of time for any help.
Bambam01 said:
So all i want to do is take everything off my 4gb sd card and use an 8gb sd card so that I have more storage space. Everything works great as is, and I wanted to keep everything as is. Just need more storage space. I've looked through the forums and haven't found anything that addresses this process. I am running CyanogenMod 7.0.3 w/a 4gb sandisk micro sd card. How do I copy so that it boots just like my 4gb card???? Thanks ahead of time for any help.
Click to expand...
Click to collapse
I recommend just writing an image file with winimage. Then writing it to a 8gb card, then using Easeus Partition manager to expand the last partition to full 8 gb.'
Do you boot from the SD card or eMMC?
If it's the latter, just copy the contents of the old card to the new one.
If it's the former, I recommend a fresh install; use a backup program (MyBackup, Titanium Backup) to back up your Apps and Data and then restore when you're done with the fresh install.
I'd like to do this as well.. in response to previous reply.. there are 4 partitions (boot, 2 other and last one with your data) do I have to create 4 different images with winimage or just for the first boot partition or does the winimage creates the image of the whole msd card?
The winimage will create a 4 gb image of your card on the 8 gb cards including existing partitions. What you'll need to do is get the largest partition to expand to the whole card. Assuming that the 4gb install on SD is the same as an 8 gb install if you did it fresh.
If the partitions are set different for 8 gb on a fresh install, you're better off just doing a fresh install and use titanium backup as the other guy said.
Phatdawg said:
If the partitions are set different for 8 gb on a fresh install, you're better off just doing a fresh install and use titanium backup as the other guy said.
Click to expand...
Click to collapse
That's a good point, the Size-agnostic SD installer uses different partition sizes for everything except the boot partition depending on the size of the card.
I tried winimage first to see if it even worked. Which it didn't. I didn't try to expand the existing partition. It just booted as a normal nook. You would think this would be a easy process but.... Lol, always new challenges. Guess that's why I enjoy doing this.
Well I tried yet again w image, expanded the partition. Still. Didn't work. I must be missing something. How hard can it be to make a copy of a bootable card? Must b brain dead today! Any other thoughts? Thanks!
Bambam01 said:
Well I tried yet again w image, expanded the partition. Still. Didn't work. I must be missing something. How hard can it be to make a copy of a bootable card? Must b brain dead today! Any other thoughts? Thanks!
Click to expand...
Click to collapse
I have done this several times, and I recommend downloading easus todo backup free. Then place both sdcards in a card reader, run todo backup and just copy the 4g to the 8g and expand the fourth partition right there in todo.
This applies especially if you want to copy to same size sd's, as you will not run into the usual image sizing issues.
Hope this helps
I don't know what you're doing wrong. before expanding the partition, make sure the sd boots, if it doesn't, then there's a problem with image being read or written as opposed to the partition.
I also had a problem with a new SD card not booting that I fixed by using the nook (that is the core nook OS) to reformat the card, then put the image onto the SDcard (shouldn't have changed anything as far as I know, but it did anyway).
Ok I tried this and it worked flawlessly. Used win32diskimager to "read" my 4gb sd with cm7 image. and then used "write" to 8gb sd card. It cloned 4 gb original image with 4 partitions and one unused partition of 4 gb. After that used easeus partition manager(latest version) to format unused pattition to fat32 and then merged with last partition of 2gb (move/resize) ..so now I have 6 gb of data partition which i can use to transfer files or move apps from nook's internal drive. The new 8gb card with cm7 image booted without any issues keeping my original settings of 4gb. One thing to mention that somehow it did not work on one pc with windows xp (kept getting write error on win32diskimager program)but worked on my laptop with windows 7.
That is exactly how I have done it in the past as I described in my first post. I don't know why a person would have trouble with it unless there was a format issue (i.e. ntsf, etc).
Hello, I new to the Nook Color. I just ordered a couple for the kids for X-Mas. I'm no stranger to rooting etc. As I understand it CM7 will be running off the Micro SD card correct? Does it matter what type of card I use? Does anything get saved to the NC internal memory such as downloads etc? My big question is, Does the Micro SD card's class have any effect on performance? Would getting a class 10 vs class 2 make a difference? Thanks.
The higher the class the faster the performance it will be if ur running the rom from the sd card which you plan to do.
I am running from internal memory but all my stuff is saved on the memory card naturally, I don't have to guide it there it just does it.
somerandomname said:
The higher the class the faster the performance it will be if ur running the rom from the sd card which you plan to do.
I am running from internal memory but all my stuff is saved on the memory card naturally, I don't have to guide it there it just does it.
Click to expand...
Click to collapse
Will it perform better from internal memory than class 10 micro sd? If so is there a guide to do this and would it still require an external card for other stuff? I plan on using CM7 stable and the guides I've seen are for booting from external.
Check this post it might help you decide on what sd card to use and wether to run from internal memory or external: http://forum.xda-developers.com/showthread.php?p=18430544
Sent from my NookColor using Tapatalk
jgaf said:
Check this post it might help you decide on what sd card to use and wether to run from internal memory or external: http://forum.xda-developers.com/showthread.php?p=18430544
Sent from my NookColor using Tapatalk
Click to expand...
Click to collapse
Thanks... I must have missed this in my search(es).
It has been extensively discussed here. The class is less important than getting a Sandisk card. Class 2 or 4 are fine. They will perform about as well as internal memory. Any others brand, even those with a higher class will suffer more FC's and not perform as well. My class 6 PNY WAS NOT EVEN CLOSE TO A CLASS 4 Sandisk.
I don't know the thread, but it is well documented and should be able to find via search.
My recommendation would be to run CM7 off the internal eMMC and use a blank SD card for backup and storage. In that case it doesn't really matter what card you use but since they are all fairly cheap these days I would get an 8GB card class 6 or higher. One for each Nook. Also get a 3rd card that you will use as a bootable card for the installation. Keep that card handy in case you ever need to reinstall CM7 or if you need to restore to stock for a warranty claim. I kept mine and keep a copy of my currently nightly (201) as well as a full stock ROM (1.3). I already had to make use of it once when I needed to have my Nook replaced under warranty.
Thanks everyone for helping me get pointed in the right direction. I plan on installing CM7 to internal memory and have everything I need to get started.
I don't know if you care, but I would do a first run on the Nook Color and register the device with B&N prior to wiping it and installing CM7 in case you run into warranty issues (such as replacing the USB cord) which you will need to have registered for.
Otherwise +1 on the Sandisk micro SD cards, class # across manufacturers varies wildly. My Sandisk class 4 16GB card outperforms both my class 6 PNY and Transcend 8GB cards in small writes/reads. I had random force closes on the Transcend when I first installed CM7 before I switched to the Sandisk.
EMMC > SD install if you like to tinker with your installs --- the agnostic sd card image here has a barebones recovery and you will not be able, afaik, to manually wipe partitions etc if you so desire or flash non-signed roms and themes (please correct me if I'm wrong, which I very well may be).
I used to dual boot (stock EMMC, CM7 SD card) but as things have progressed this year there's no reason for me to stick to even nootered stock --- the performance difference between stock and CM7.x is massive, and the big bugs have been fixed (SOD, battery drain). Even if you like the default reader app, there's great generic ereaders out there (and now with Overdrive app from Google Market, the ability to borrow DRMed epubs like you could with the native Nook reader client).
Just one note I would add to the above. When deciding between an internal install and dual boot, note that some have reported issues with the latch for the sd card breaking with frequent removals of the sd cards. This latch repair requires factory return. I, personally, would recommend internal install with an sd card for storage. This will prevent frequent removal of the sd card and will extend the life of the card latch.
Just my two cents.....
Sent from my Touchpad using Tapatalk
You don't have to remove the sd card to boot stock.. just power up while holding the N button and you will be given a choice of which system to boot.. this is true if using the Size Agnostic procedure documented here on XDA.
Moshe5368 said:
Just one note I would add to the above. When deciding between an internal install and dual boot, note that some have reported issues with the latch for the sd card breaking with frequent removals of the sd cards. This latch repair requires factory return. I, personally, would recommend internal install with an sd card for storage. This will prevent frequent removal of the sd card and will extend the life of the card latch.
Just my two cents.....
Click to expand...
Click to collapse
The point is well-taken because every time you update your rom, you'll have to take out the card, BUT you have to do that even with the internal memory (emmc) install. But as the previous post indicated, you don't need to take out the card just to boot to stock. I would strongly recommend that you not install the rom to the emmc until after your warranty expires. That way, if you have any problem with the NC, you can simply take out the card, and you're back to stock, i.e. none of the "restore to stock" stuff you'd need to do if you put CM7 on the emmc.
without re installing cyanogenmod on the usd, is there a way to move all partitions from a 2gb to a 16 gb micro
YoshiFan501 said:
without re installing cyanogenmod on the usd, is there a way to move all partitions from a 2gb to a 16 gb micro
Click to expand...
Click to collapse
I assume you have CM installed on SD. You can use win32diskimager to write an image file of the SD to your PC. Then put your new SD in and write the image to it. It will still only be 2GB on the card, but you can use Mini-Tool Partition Manager (free on web) to fix that. First I would move partition 4 a little to the right so that you can expand partition 3. On a 2GB SD, verygreen made partition 3 only 612MB and it really needs to be larger. 1 or 2 GB. Then expand partition 4 to fill the rest of card.
Sent from my Nook Color running ICS and Tapatalk
YoshiFan501 said:
without re installing cyanogenmod on the usd, is there a way to move all partitions from a 2gb to a 16 gb micro
Click to expand...
Click to collapse
Get a copy of Easeus ToDo Backup Free. It will allow you to clone the 2gb onto the 16 gb sd and use all the available space in one step.
Not to thread jack but,
I am having trouble doing this exact thing too. I used winimage to "read" my working sd card. Then put my new 16gb sd card into my usb adapter and "write" the boot.ima image to the new card. Both reading and writing take about 5 seconds.
When I put the new card into my nook, the nook just boots into stock.
donniebball23 said:
Not to thread jack but,
I am having trouble doing this exact thing too. I used winimage to "read" my working sd card. Then put my new 16gb sd card into my usb adapter and "write" the boot.ima image to the new card. Both reading and writing take about 5 seconds.
When I put the new card into my nook, the nook just boots into stock.
Click to expand...
Click to collapse
Don't use winimage. I have found it troublesome. It should take much longer than 5 seconds. Use win32diskimager.
leapinlar said:
Don't use winimage. I have found it troublesome. It should take much longer than 5 seconds. Use win32diskimager.
Click to expand...
Click to collapse
Thanks, tried win32 and it worked. I knew there was something wrong when it only took 5 seconds to write the image.
Under storage settings.
Shows me SD Card total space 116MB Available space 12.52MB. My SD card was a 32 gig class 10.
Internal storage 4.9GB
Available space 4.33GB
Also C7 will boot without memory card in it. My cousin helped me root it and we used the SD card to root it. According to him I should be able to take the SD card out and boot into the normal NOOK settings. This correct?
I am getting errors when I try to install things to SD. Tells me there is not enough room.
Sorry if this doesn't make much sense still very new to this.
Thanks for the help.
First, go to Settings>CyanogenMod settings>Application> and make sure Use internal storage is unchecked.
Then go to Setting>Storage and let us know about SD card, Internal and Additional storage values.
K9Shep said:
Under storage settings.
Shows me SD Card total space 116MB Available space 12.52MB. My SD card was a 32 gig class 10.
Internal storage 4.9GB
Available space 4.33GB
Also C7 will boot without memory card in it. My cousin helped me root it and we used the SD card to root it. According to him I should be able to take the SD card out and boot into the normal NOOK settings. This correct?
I am getting errors when I try to install things to SD. Tells me there is not enough room.
Sorry if this doesn't make much sense still very new to this.
Thanks for the help.
Click to expand...
Click to collapse
Sounds like you installed CM7 to the internal memory, not to an external SD card. that's probably why you are seeing the space available on internal memory, but not the SD card. There is Verygreens's method to install CM7 and CM9 to the external card, leaving the stock Nook ROM in place, but it doesn't sound like you used it. To get answers to most of your questions, go to Leapinlar's great information page here:
Leapinlar's Tips
Specifics relating to installing CyanogenMod on an SD card are in the second post.
shumash said:
Sounds like you installed CM7 to the internal memory, not to an external SD card. that's probably why you are seeing the space available on internal memory, but not the SD card.
Click to expand...
Click to collapse
Yes, I agree. It sounds like his friend set it up to install to SD by burning the image to the card, but somehow flashed the rom to internal memory instead. That would explain the 5GB internal space and 116Mb SD card space.
He needs to reformat the SD card to get the full size of the card available.
leapinlar said:
Yes, I agree. It sounds like his friend set it up to install to SD by burning the image to the card, but somehow flashed the rom to internal memory instead. That would explain the 5GB internal space and 116Mb SD card space.
He needs to reformat the SD card to get the full size of the card available.
Click to expand...
Click to collapse
Well sounds like the stock nook interface is gone then. No big deal. Do I just reformat the SD card through the settings in android? The option states Erase SD Card. Would that be what I want to do?
Also not sure if this is related. But sometimes C7 wont boot when I have the SD card in. Take the SD card out and it boots just fine.
Well I grew a pair and did the Erase SD Card. Now it is showing 29.66GB.
K9Shep said:
Well I grew a pair and did the Erase SD Card. Now it is showing 29.66GB.
Click to expand...
Click to collapse
LOL. Good job. Yes, stock Nook is gone. I can help you get it back if you want it, but most never miss it. The only reason people want it is for warranty or if they want to have kids books work.
Random side question but figured since I have ya here.
Any idea on a good note taking app for android? As in for school notes like during class?
K9Shep said:
Random side question but figured since I have ya here.
Any idea on a good note taking app for android? As in for school notes like during class?
Click to expand...
Click to collapse
Don't use it much for that, but Googling yields this:
Best note-taking apps for Android
So I am running CM7 off of an sd card in my nook color.(Using http://forum.xda-developers.com/showthread.php?t=1904129 and I highly recommend). Win32discimager for some reason created a small partition just larger than the installer which remains on the card. I also have the android OS on the card that is taking up 1 gb partition. The rest of my 16gb micro sd card is labeled as the emmc for the tablet which is not what i intended. Now I cant load it up with my movies and videos like I had hoped.
Does anyone know:
Is there any way I can change these partitions on my card? (I have already tried EasuUS partition manager)
Where did the 1gb partition that android is on come from and why did the emmc get so large?
Is there any way to take the android image currently on my sd card and just putting onto the nook after I have already had it run from the sd card and then just formatting my sd card for storage?
There are probably newbie questions but I have tried to do my own research and havent found any certainties. Any help would be really appreciated.
posturize said:
So I am running CM7 off of an sd card in my nook color.(Using http://forum.xda-developers.com/showthread.php?t=1904129 and I highly recommend). Win32discimager for some reason created a small partition just larger than the installer which remains on the card. I also have the android OS on the card that is taking up 1 gb partition. The rest of my 16gb micro sd card is labeled as the emmc for the tablet which is not what i intended. Now I cant load it up with my movies and videos like I had hoped.
Does anyone know:
Is there any way I can change these partitions on my card? (I have already tried EasuUS partition manager)
Where did the 1gb partition that android is on come from and why did the emmc get so large?
Is there any way to take the android image currently on my sd card and just putting onto the nook after I have already had it run from the sd card and then just formatting my sd card for storage?
There are probably newbie questions but I have tried to do my own research and havent found any certainties. Any help would be really appreciated.
Click to expand...
Click to collapse
Ok, first you need to go to my tips thread linked in my signature and read in section B how the verygreen SD works. You will understand the partition structure a little better.
Now for your sdcard/emmc media storage problem, you have a setting wrong in CM7. Go to settings, CyanogenMod settings, Application and uncheck "Use internal storage". What that setting does is swap emmc and sdcard so that your real sdcard is called emmc and internal media storage is called sdcard. It is not default that way. Somehow it got checked.
Sent from my Nook HD+ using Tapatalk