Related
I have done hard reset and soft resets and still my wifi is not connecting.
Finally my EDGE is working great but wifi not. Whenever I try to connect my SSID is set to "EMC Wireless Internal" channel 11. I have no idea where this cam from but I can not get rid of it. I have a new FIOS Actiontec router with wireless enabled to my network name, channel 10. And Hitchhiker tries to connect but it keeps getting bumped off.
I have gone into MediaNet and turned off the proxy and checked for it to go onto the internet on Cingular GPRS.
I have not had a problem connecting before on wifi. I wonder if the router is a problem here, or if my phone settings are screwed up.
And ideas?
Thanks
The WiFi - EDGE contengency
*The Bad News*
By default, if EDGE/GPRS is configured to work, WiFi is rendered useless.
You didnt mention what carrier you have. I have Cingular and they even state on there website that If you configure the Edge/GRPS to connect, then WiFi may not work.
*The Good news*
I have my 8125 working with both Edge and WiFi. Heres what I did:
1. Open Connnections and click on the 'ADVANCED' tab.
2. Click on 'SELECT NETWORKS'.
3. The top pull down should be set to 'MY ISP' or, if you have named your WiFi connection something different, select it here.
4. Click 'EDIT' under this pull down and set connection to 'AUTO PICK'. 'OK' back to Network Management screen.
5. The bottom pull down should be set to 'MEDIA NE'T.
6. Click on 'EDIT' under this pull down. This is where you will set up EDGE using your carrier's settings.
7. 'OK' your way back out. Your done.
These settings let WiFi try to connect first. If no WiFi is available then EDGE/GPRS is used.
Good Luck!
Thank you! Worked for me, but videos streamed from orb still aren't working
Wierd-Fi
I also have WiFi problems after installing HTC official upgrade
ROM 2.25.11.1 WWE
Date 5/11/06
Radio 02.25.11
Protocol 4.1.13.12
ExtROM 2.25.11.102
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message. This happens even when not connected to CIngular EDGE/GPRS (flight mode ON then, individually enable WiFi ON for what that's worth). When I delete my home network WiFi entry to force a re-recognition and setup, it recognizes the wireless net just fine (again) but same behavior.
All my settings are already set as suggested by ralugniC8125 in this thread. I had not tried any of the other ROMs with added features/hacks/fixes found on this website ... would any of them behave differently, you think? PHone was bought from Cingular .. I have not done any unlock procedure (don't really need to from a service standpoint but will if necessary to make a new ROM work right).
Any thoughts appreciated...
tskelton said:
Everything is great except after successful connection to home WiFi it disconnects after maybe 5 to 15 seconds ... network becomes "unavailable" .. no error message.
Click to expand...
Click to collapse
I have just purchased an unlocked Tilt from eBay. I have been scanning the wiki for days now, along with other sources, and to no avail. I still cannot get my WiFi to work properly. If any one has had this issue and has found a solution, I would love to know it!
ok, here's a suggestion since none of you have mentioned it.
Diable the MAC (Media Access Control) Binding on the router. This should help.
Maybe yall can help me now I have it attempting to connect however it only connects to gprs and it even shows it has a great wifi signal
Still Wifi-less and Woeful
lobotomy said:
Diable the MAC (Media Access Control) Binding on the router. This should help.
Click to expand...
Click to collapse
Thanks for the suggestion. This did not help unfortunately. I should mention that I have tried to access several different types of routers... with and without security, and while they are showing up as being available, they will not stay connected for more than a second or two.
Any other possibilities?
I'm currently using:
ROM: [02 Jun] WM 6.1 CE OS.19588 from Diamond - CLEAN *FAST!*
I have some problems with the wi-fi. Whenever I would go standby, and turn it back on, the wi-fi would try to connect but it doesn't and just says it's available and gives me a lot of networks to access. What I want is whenever I come back from standby, I want it to automatically use the wi-fi at my house.
Please help.
I had a similar problem with my Wizard. I am not sure exactly what the solution was but I seem to recall that the problem was linked to wireless 'G' compatibility. I disabled the 'G' and now only access my access point through 'B' only. Works a treat every time. You can disable the wireless 'G' in the registry fairly easily. Let me know if you need instructions.
Configure wifi as your home network and then cellular gprs as your work network. Viola! Works everytime then!
BUMP! Help.
Reflashed my Jade from UK Orange to JADEMAN rom recently...
I don't think this is a ROm related problem (unless you know otherwise !) so I have posted in general part of forum.
Can anyone tell me how to force the phone to use Wifi to connect to the internet.
It connects via GPRS fine but i want to disable the GPRS DATA for travels abroad so I don't run up a huge data bill. I can stop the data with "NoData" app, but if I now try to connect to internet with Opera or Internet explorer if fails..
Is there something I am missing, to tell it either to connect via wifi before using GPRS data or to only connect via wifi. Do I need to create a connection ?
The create new connection page doesn't list using WiFi, bluetooth is the only "WIRELESS" type connection that appears to be offered.
Also when the wireless AP list is shown and I try to connect to an AP showing available that I have previously setup with WEP key etc, it fails to connect.
I am sure to be missing something but I can't spot what the problem is...
Any help appreciated.....
Phil
Normally Windows Mobile connects via WiFi first, if available, and only when not present it uses GPRS. That means that you do not need to disable GPRS if an WiFi-connection is established.
I have no personal experiences with "NoData". Perhaps someone else can help.
phil-w said:
Can anyone tell me how to force the phone to use Wifi to connect to the internet.
It connects via GPRS fine but i want to disable the GPRS DATA for travels abroad so I don't run up a huge data bill. I can stop the data with "NoData" app, but if I now try to connect to internet with Opera or Internet explorer if fails..
Is there something I am missing, to tell it either to connect via wifi before using GPRS data or to only connect via wifi. Do I need to create a connection ?
The create new connection page doesn't list using WiFi, bluetooth is the only "WIRELESS" type connection that appears to be offered.
Also when the wireless AP list is shown and I try to connect to an AP showing available that I have previously setup with WEP key etc, it fails to connect.
Any help appreciated.....
Phil
Click to expand...
Click to collapse
MvBoe said:
Normally Windows Mobile connects via WiFi first, if available, and only when not present it uses GPRS. That means that you do not need to disable GPRS if an WiFi-connection is established.
I have no personal experiences with "NoData". Perhaps someone else can help.
Click to expand...
Click to collapse
AFAIK the moment you invoke any app that requires internet connection (weather update, activesync, opera) Jade invokes data connection first (3G, GPRS, etc) That's how it works on my set. Unless you invoke Wi-Fi connection first, then data connection is ignored.
I have had a bad experience that even if all setups are ok Wi-Fi conn thru Ap fails.
Corrected such a way;
Under 'Wireless /Lan' settings
Power mode should be brought to 'best performance'
azahidi said:
AFAIK the moment you invoke any app that requires internet connection (weather update, activesync, opera) Jade invokes data connection first (3G, GPRS, etc) That's how it works on my set. Unless you invoke Wi-Fi connection first, then data connection is ignored.
Click to expand...
Click to collapse
That's what I meant: You have to activate WiFi by yourself to prevent jade using GPRS (etc.). Your description is more precise, I did not make it clear enough. Thanks for correction.
Hi and thanks for replies so far...
I have just done a hard reset to make sure I haven't loaded anything that may mess up the wifi connection... Even when wifi is on and I am connected to a wifi access point OK it still uses gprs/3g not wifi..
Back to the "drawing board" I think...
Any more ideas please...
Phil-w
with this app you can disable or enable data connections as you please.
there is another app here in the xda that will disable data when roming automatically, but i don't remember the name.
faria said:
with this app you can disable or enable data connections as you please.
there is another app here in the xda that will disable data when roming automatically, but i don't remember the name.
Click to expand...
Click to collapse
Hi faria
Unfortunately I find it better to go into connection manager, select airplane mode, then enable wifi. Then do any surfing, live messenger etc. Then once finished go back into connection manager, re-enable phone.
Like others, I'm on Orange, wifi no longer stays the internet source even if it is connected. I have it on all the time, but if I use the internet, I have to go through the above procedure or it costs me credit through Orange.
Janeway
janeway said:
Unfortunately I find it better to go into connection manager, select airplane mode, then enable wifi. Then do any surfing, live messenger etc. Then once finished go back into connection manager, re-enable phone.
Click to expand...
Click to collapse
The only disadvantage is here is that, you'll miss calls when there are incoming calls because your phone is inactive (while PDA is). You can just disable data connection (CommManager - Data Connection - off) and leave wi-fi connected.
Like others, I'm on Orange, wifi no longer stays the internet source even if it is connected. I have it on all the time, but if I use the internet, I have to go through the above procedure or it costs me credit through Orange.
Click to expand...
Click to collapse
Just wondering.. how you identify which connection is being used, wi-fi or 3G/GPRS when both are connected.
What if you disconnect data connection (3G/GPRS) without activating the airplane mode, can you surf using wi-fi connection.
One possible reason - set connected to the AP via wi-fi but AP is not connected to internet, thus set seeks 3G as another route to internet.
Hi azahidi, thanks for taking time to reply to me . Your points as follows:
Yes, missing calls is the disadvantage, but I use my pda more for data and hardly any calls, so not so important for me, but obviously we be much better if that were possible as I do sometimes forget to swich back. If I disable the data connection, it automatically re-initializes itself as soon as ANY data is being transmitted - even with just wifi active - except when it is in airplane mode. This is a new thing for me with the Jade, didn't have that problem before with my previous HTC phone.
There is an icon for the 3G - when its in use it shows it - it goes from being a large G in a square to a smaller one with signal bars.
Wifi is definitely connected, I surf online with it all the time.
Its like 3G has priority over wifi - there should be a way to change that.
Hope the above makes sense.
Janeway
I'ven been using 'Nodata' succesfull the last past months, it does it's job well, but i'm not on Orange as you are, that might be the difference.
Just to be sure i've also changed my settings:
start > settings > connections > connections > advanced > select network > My work network (twice).
and
start > settings > connections >advanced network > uncheck HSDPA and in SMS choose 'GSM'
(all is translated from Dutch, hope i used the right words)
Thanks Nirak.
One of my settings was wrong - I should have known that from last time, but my brain's elsewhere at the moment!
Must have upset it when I flashed
Cheers for now.
phil-w said:
Hi and thanks for replies so far...
I have just done a hard reset to make sure I haven't loaded anything that may mess up the wifi connection... Even when wifi is on and I am connected to a wifi access point OK it still uses gprs/3g not wifi..
Back to the "drawing board" I think...
Any more ideas please...
Phil-w
Click to expand...
Click to collapse
Phil, can't you simply switch the "Data Connection" on/off switch to 'off' ?
I have it in the Comm Manager right at the bottom. The Wi-Fi and Phone could be left 'on'. I can't try if it works because I only use the phone on 2G.
Joe
jfranek said:
Phil, can't you simply switch the "Data Connection" on/off switch to 'off' ? I have it in the Comm Manager right at the bottom. The Wi-Fi and Phone could be left 'on'. Joe
Click to expand...
Click to collapse
That's how it should work actually. Either one, Wi-Fi or 3g/GPRS. But what phil is saying is that it also activates data connection (3G/GPRS) even when wi-fi is connected.
On my set, and in my network (not Orange but standard GSM).. this is how it works :
The moment I invoke any application that requires internet connection (weather update, activesync, opera, etc) Jade invokes data connection first (3G, GPRS, etc). Unless if I invoke Wi-Fi connection on first, then data connection is ignored, it will stay off.
So what I normally do is, whenever I want to use internet, I connect using wi-fi then browse the internet. If there is no available AP, then I turn off wi-fi and continue browsing , which is then connected using 3G/GPRS/EDGE?HSDPA
azahidi said:
(...) The moment I invoke any application that requires internet connection (weather update, activesync, opera, etc) Jade invokes data connection first (3G, GPRS, etc). Unless if I invoke Wi-Fi connection on first, then data connection is ignored, it will stay off.
So what I normally do is, whenever I want to use internet, I connect using wi-fi then browse the internet. If there is no available AP, then I turn off wi-fi and continue browsing , which is then connected using 3G/GPRS/EDGE?HSDPA
Click to expand...
Click to collapse
This is the way it normally works and should work under WindowsMobile. The Orange-ROM seems to be "manipulated" by the provider (?) not to work in this desirable way. All (or some?) Orange-ROM-Handsets seem to activate the data connection (3G/GPRS) every time ignoring the established Wi-Fi-connection. This rises the providers business volume.
It would appear to be correct about orange having had the method of connection changed.
I have just found and installed a different RADIO.ROM to my Orange Touch 3G and now it appears to connect as required.
Still not 100pc happy but will post my observations later with the rom numbers if it helps anyone else out..
Phil-w
Look on the HTC JADE reflashing on this site
Hi All,
There is no way around the Orange apps to enable WiFi, but I successfully reflashed the Roms in my Orange touch 3g yesterday.
Have a look here for the details on what to do:
http://forum.xda-developers.com/showthread.php?t=514406
Follow the instructions carefully, and I chose to install the Stock HTC ROM 1.40.721.2 from the ROM post.
Wifi is then free....
)
Well I appear to have got around the Orange Unique problem.
I upgraded the Rom on my Orange UK Touch 3G to the Jademan SuperRom V3. That got rid of the Unique side of things but with no improvement with Wifi connectivity.
The connectivity problem with wifi still caused problems, the internet connection would NOT use wifi even if I disabled the GPRS / 3G data connection with "NoData" It just returned a message saying it had failed to connect.
I decided to find a new radio rom image which I managed to on this Jade forum. I flashed the new rom and tested the same connections again. This time the wifi connected via Wifi first and without any problem... It would appear that flashing the Jademan rom didn't update the radio as well, I needed to update the radio as well.
The clue may be in the radio rom version number,
Original orange 0.29.30.U23
New Radio rom 0.41.30.12
A assume that the U in the orange rom refers to "Unique", which now I have replaced it, it appears to have cured the wifi problem and it is working just as any other Non-Orange Jade / Touch 3G does....
I have not noticed any problems with any other radio related issues since the upgrade, GPS, 3G/GPRS etc all seem to be fine.
I do find that the phone does struggle to connect with some Dlink AP's though... It may be a problem with the Dlink more than the phone but I still need to do more tests on that.
May be that will help a few other people out there...
Phil-w
Hi Phil,
I had exactly the same problem!
Started with an unlocked HTC Touch 3G with Orange customised ROM and then replaced it with the SuperROM. WiFi was unusable so (having read your post) I re-flashed with the standard ROM released from HTC and then re-flashed the SuperROM. This gave me the same Radio ROM that you show above however the WiFi problems seemed to be no better.
While I liked the idea of having the SuperROM I have gone back to the latest standard HTC ROM and all seems to be well.
John
Hi John,
My wifi now seems fine except not liking Dlink AP's for some reason.
I don't even need to stop gprs data with NoData etc, if there is a wifi connection available that I have setup previously it will use that rather than GPRS..
I appear to have "de-Oranged" it !!!
What probs do you still have on your Touch 3G ??
Phil
Xda-viewers,
yesterday i tried to put on my WiFi, but it didn't work anymore
I have my HD2 for about 1month, very happy with the phone,
and this is the first mayor malfunction
When i press WiFi ON in the comm-manager it shows it's loading,
and then nothing, doesn't go ON,
turned the phone off-on, soft reset.. nothing..
anyone else had this glitch?
hard reset or other solution?
It always worked, untill yesterday
If I were you I would go for a full backup with SPB, and then restore (maybe excluding everything regarding the wifi) after a hard reset
I would try doing hard reset.
However, I had the same problem with my old Fujitsu Siemens Pocket Loox N560 and they had to exchange mainboard.
Do you have it charging? I can't seem to connect to any Wifi networks when I have the phone plugged in. Once i disconnect it, it works fine.
If you are connecting it using USB, make sure WMDC / ActiveSync is set to allowing your phone wireless connections while connected to your PC!
???
phone is fully charged
not connected to PC or anything
not working, going to try some things
anyone goto suggestions except hard reset?
else i hard reset tommorow,
thankz
You mean you can't turn ON or NOT CONNECTING?
If its not connecting, did you try to delete the connection settings from advanced wireless settings and try reconnecting again?
skr_xd said:
You mean you can't turn ON or NOT CONNECTING?
If its not connecting, did you try to delete the connection settings from advanced wireless settings and try reconnecting again?
Click to expand...
Click to collapse
It's really not turning ON.
I press the Off-On button, I see it loading and then, nothing,
WiFi is still turned OFF.
timodc said:
It's really not turning ON.
I press the Off-On button, I see it loading and then, nothing,
WiFi is still turned OFF.
Click to expand...
Click to collapse
I've got exactly the same problem - have only noticed it today.
If I go into wireless network config and select my network there and click connect, it takes ages before it says "connected" and then immediately changes to "not connected". I've obviously checked and rechecked my settings. It simply will not connect any more.
i also can't remember installing an update which would cause this probleme..
Connected to PC
When connected to PC, in the comm manager, the WLAN is dissabled, can't even push it, maybe something went wrong with disconnecting and this is the reason why my WiFi is not working - going on?
Anyone?
I'm not at home, so can't do anything with mine at the moment, but out of curiosity, did you use then Wifi N option in BsB Tweaks? That's the only thing Wifi related that I can think of touching recently.
Tried it
Indeed, thought the same,
tried to put Wifi-N off, soft-reset, but no change
Almost at the edge of HARD-reset
timodc said:
Indeed, thought the same,
tried to put Wifi-N off, soft-reset, but no change
Almost at the edge of HARD-reset
Click to expand...
Click to collapse
I really hope it doesn't need a hard reset. I'm not gonna be happy if I have to do that AGAIN!
I'm gonna keep searching, in the hope of finding a solution.
Out of curiosity, do you ever use the Wifi router app?
WM-Wifirouter
I tried to use the Wlan-Router with Comm manager,
didn't work that well,
installed app I had on my P3600: WM-Wifirouter,
this worked like a charm,
Timo
I've solved my problem! Yay!!
I don't know if this will be of any help to you, but give it a try and see how you get on.
Basically, when using the in-built wifi router, it assigned the IP address 192.168.1.1 to the wireless adapter. This is fair enough, for a router, but obviously not for when you want to connect to a wifi network and get assigned an IP address automatically.
I had seen other people suggest that this may be the problem, so I'd already checked my IP settings for the wireless adapter, and they were set to automatic.
However, if you run the wifi router and then go to your IP settings, it says 192.168.1.1. Set it to automatic while the router is running.
This made my phone get a bit upset, and I ended up reseting it, but since then I've been able to connect to my home network again.
So...
1. Run and start the wifi router
2. Go to settings, Connections, Wifi, Wireless networks, Network Adapters (tab)
3. Select the network adapter (Broadcom 802.11 DHD Network Adapter)
4. Change to use a server-assigned IP address, instead of a specific one
5. Click OK
6. Reset the phone - don't close the wifi router app first.
7. When it starts up, go to the comm mananger and disable wifi.
You should now be able to start wifi and connect to your home network. (It may do it automatically if you don't do step 7 - I'm not sure).
Give it a try and let us know how you get on
Sensational johncmolyneux!!!
I had this problem too - it was doing my head in, but now seems like an obvious conflict. Thanks for finding the solution.
Now all I need to do is solve my BT Voice Commander problem (reported in many other threads) and the HD2 will have the same functionality as the Hermes it has replaced ;-)
Cheers,
Lordbowl
You still haven't hard reset?! I am doing hard reset every 6days because of mod/theme and other crap testing
Backups with resco/pim/office2007 entreprise on windows 7 beta do the trick to have phone working in 15 minuts.
johncmolyneux said:
I've solved my problem! Yay!!
I don't know if this will be of any help to you, but give it a try and see how you get on.
Basically, when using the in-built wifi router, it assigned the IP address 192.168.1.1 to the wireless adapter. This is fair enough, for a router, but obviously not for when you want to connect to a wifi network and get assigned an IP address automatically.
I had seen other people suggest that this may be the problem, so I'd already checked my IP settings for the wireless adapter, and they were set to automatic.
However, if you run the wifi router and then go to your IP settings, it says 192.168.1.1. Set it to automatic while the router is running.
This made my phone get a bit upset, and I ended up reseting it, but since then I've been able to connect to my home network again.
So...
1. Run and start the wifi router
2. Go to settings, Connections, Wifi, Wireless networks, Network Adapters (tab)
3. Select the network adapter (Broadcom 802.11 DHD Network Adapter)
4. Change to use a server-assigned IP address, instead of a specific one
5. Click OK
6. Reset the phone - don't close the wifi router app first.
7. When it starts up, go to the comm mananger and disable wifi.
You should now be able to start wifi and connect to your home network. (It may do it automatically if you don't do step 7 - I'm not sure).
Give it a try and let us know how you get on
Click to expand...
Click to collapse
-When I try to connect the WLAN-Router with the Comm Manager, it keeps on loading and nothing happens.
-When I try the WM-Wifi-Router app which I used on my P3600, it says not abble to connect WLAN
-All my settings are server-assigned-IP-address
Still not able to put on my WLAN,
Timo
hello,
i have the following problem with wifi on my zopo zp 700: it connects to our home- wifi, but only grey connectifity stripes, not the blue ones i get usually. it says "connected" but internet doesnt work.
when im at work the wifi works fine.
i started the dignostic tool by dialing*#*#4636#*#* and found out that there are 2 configured versions of our home wifi there, one with keymgmt (ID9) and one without (ID10).
it seems that the phone connects to the wifi without kegmt and this causes the problem. when i disable the network with ID10 (the one without keymgmt) it works until i switch off the wifi and on again. then the network with ID10 (and all others that i had disabled before are enabled again)
as there are several other networks that i dont know but seem configured in this list, i wanted to know how i diable or delete these unwanted networks from the list of configured wifis?
thx in advantage and best regards,
nick
Try to factory reset your wifi or gateway
Sent from my GT-I9105P using XDA Premium 4 mobile app
How do you do that? I opende the engineer mode but did only find different testing modes for wifi..
Reset button or something like that on your wifi device. Let use them to reset to factory
Make an hard reset :good:
This might be a stupid idea, but can you not just go into Wifi settings, pick your home network name, and select 'Forget'?
Make sure you forget all you want it to forget (i dunno if it will list it twice or not)...
Then re-do the settings with correct password...fixed?!?
You should check if you get an ip address from your wifi router.