Related
I've used rsd lite several times before and have not had any problems. I just recently ran it on my phone but i accidentally used the old .sbf file instead of the one for the updated firmware. I tried using the new .sbf file afterwords and its stuck and wont boot. what do i do?!?! please help
what is says on my screen is:
Bootloader
30.04
err:A5,70,70,00,1f
mew_map blank
service req'd
battery ok
ok to program
transfer mode:
usb
Which "old" sbf did you use and which "new" sbf did you use? Also what system version were you on prior to using either of the sbf files?
i was on the latest official ota update from verizon and ran the VRZ_MB810_2.3.15_1FF_01.sbf which is the old .sbf and the i ran the SHADO_X6_2.3.34_SYSTEM-ONLY.sbf which is what i thought to be the latest one
System only will do you no good at this point. You need to flash the FULL 2.3.32 sbf and yes it will work with the OTA.
http://www.mydroidworld.com/forums/droid-x-discussion/5633-droid-x-2-3-32-full-sbf.html
ok thank you soooo much, your a life saver. going to give that a try now and get back to you
These are the steps i took to get back to the Stock bell rom. I take no credit for this method, NFHimself made the scripts, and mods for deodexing.
This takes an hour at least.. Make sure your battery is FULLY charged, Do a backup first as well to save your sd card contents.. You have to do a factory reset after the process is complete.
1)reinstall a fresh sbf of the french 2.1.1 and login to motoblur. French sbf can be found in this thread, Close to the bottom of the page.
2) enable usb debugging.. menu, settings, applications, development, then check usb debugging
3) go to NFHimselfs deodex/mod thread here
4)download Version 9, and extract it to your computer
5)Run the menu.bat file
6) choose the root option. and follow the instructions. If it doesn't complete successfully, unroot and try again. Took me a couple times to get my phone rooted properly.
7) once root is complete, choose restore phone. This will automatically download the files needed to get you back to the stock rom. It will take a little bit of time to download, so have a drink or smoke or something.
The restore will take an hour or so to complete. Be patient.
I got to the point where it said waiting for phone to shutdown, so i pulled the battery and did it manually. Once my phone booted back up again, it was on the stock bell rom.
Thanks to all who helped me! Y2whisper and kieller from the support.motorola forums.
Don't forget to thank NFHimself.
NOTE: I had to do a factory reset to get the Market app back.
I managed to get the bell update with no problems!
right on I was wondering how I would get back to the stock Bell.....I'm running the French 2.1.1, so when the time comes I can sit back for an hour or so and bring the phone back to stock...........yaaaahoooo......
nate_benji were you on the french 2.1.1 before you did this?? cause I'm on 2.1.1 and I am rooted, just wondering if I have to do all over... flashing 2.1.1 again and root??? but I guess it can't hurt with a fresh install......guess I'm getting lazy in my old age...lol
dillfever said:
nate_benji were you on the french 2.1.1 before you did this?? cause I'm on 2.1.1 and I am rooted, just wondering if I have to do all over... flashing 2.1.1 again and root??? but I guess it can't hurt with a fresh install......guess I'm getting lazy in my old age...lol
Click to expand...
Click to collapse
Yes, i was on the french 2.1.1. The only reason i did a fresh install of the french 2.1.1 sbf is because the rooting method is a little different than using gingerbreak. I tried with a normal root, but it didn't work. NFHimself's mod/deodex application has the root option built in. That's what I used, and it worked well.
What's the benifit over the french 2.2.1 ???
YBrazeau said:
What's the benifit over the french 2.2.1 ???
Click to expand...
Click to collapse
The new update, I presume.
If I get bored between now and an international release or leak of GB then perhaps I'll give this a shot too. Thanks for sharing it, guys! Great work as always.
YBrazeau said:
What's the benifit over the french 2.2.1 ???
Click to expand...
Click to collapse
The benefit is you get the bell updates, who knows when the other carriers will release the gingerbread updates. Mind you bell is slow at releasing anything..
Sent from my MB860 using XDA App
Thanks nate, then when the time comes that's exactly what I shall do......
The biggest benefit of this would probably be that when you do this it would be really hard to tell if you ever modded the phone. Also Bell is likely to get the Gingerbread update before people in Europe.
I am doing a restore and got a tar crc error and a error on restoring mmcblk0p3 - should i wait till it finish .....i don't like the the crc error..thanks 1 done cat /data/local... ! bus error shsu (no boot) failed to boot 2 ...starting rsd mode, reflashing now...anyone know why there is a crc fail..
Could it be possible to get a direct link to the French 2.2.1 sbf, this way everything needed is in one location?
Thanks
capercb said:
I am doing a restore and got a tar crc error and a error on restoring mmcblk0p3 - should i wait till it finish .....i don't like the the crc error..thanks 1 done cat /data/local... ! bus error shsu (no boot) failed to boot 2 ...starting rsd mode, reflashing now...anyone know why there is a crc fail..
Click to expand...
Click to collapse
I am having this exact same issue. Is the mmcblk0p3 file that is included within the backup_OLYLA_U4_0.37.4.tar.gz that NFHimself posted possible corrupt?
davisx said:
I am having this exact same issue. Is the mmcblk0p3 file that is included within the backup_OLYLA_U4_0.37.4.tar.gz that NFHimself posted possible corrupt?
Click to expand...
Click to collapse
I don't think so. i did it from a fresh flash of 2.1.1 and it worked fine. you just have to make sure you rooted using his scripts. that was a problem i was having using his app before i used these scripts.
capercb said:
I am doing a restore and got a tar crc error and a error on restoring mmcblk0p3 - should i wait till it finish .....i don't like the the crc error..thanks 1 done cat /data/local... ! bus error shsu (no boot) failed to boot 2 ...starting rsd mode, reflashing now...anyone know why there is a crc fail..
Click to expand...
Click to collapse
I had that too i believe. Not sure why mmcblk03 failed, but all the rest passed for me. Did you re-sbf and try it again?
fearthefox said:
Could it be possible to get a direct link to the French 2.2.1 sbf, this way everything needed is in one location?
Thanks
Click to expand...
Click to collapse
I updated the original post, with a link to another thread that has a list of all known atrix sbf's. The french one is close to the bottom of the list.
Is this the one you are referring to...
Branding: Retail France
Version: 2.1.1 Full
Android Version: 2.2.2
Bootloader Version: N/A
Webtop version: N/A
Requires RSD Lite 5.0.0
Requires Moto Android (De)packer 1.3 to edit.
As you opening post says french 2.2.1 and I cannot find that on the page you linked to.
nate_benji said:
I had that too i believe. Not sure why mmcblk03 failed, but all the rest passed for me. Did you re-sbf and try it again?
Click to expand...
Click to collapse
Ya I got it but really weird ..notice when the program expands there is no mmcblk03 in the file also when it finish it keep coming up as timeout so I removed it from usb and pulled out the battery restarted and dl the update..It seems like a good update so far..ty
Sent from my MB860 using XDA App
Hi,
I removed partition 3 from the backup, it's your Motorola pds partition, it's not necessary to get back to stock, there are no sbf files that overwrite it. I also updated the atrix mods app to not reference partition 3.
Cheers!
NFHimself said:
Hi,
I removed partition 3 from the backup, it's your Motorola pds partition, it's not necessary to get back to stock, there are no sbf files that overwrite it. I also updated the atrix mods app to not reference partition 3.
Cheers!
Click to expand...
Click to collapse
Awesome! Thanks for creating the scripts, and the app. Made it possible to get me back to the stock bell rom, without a cwm backup. Now that reminds me, time to root, install cwm and do a backup!
Thanks again NFHimself..
fearthefox said:
Is this the one you are referring to...
Branding: Retail France
Version: 2.1.1 Full
Android Version: 2.2.2
Bootloader Version: N/A
Webtop version: N/A
Requires RSD Lite 5.0.0
Requires Moto Android (De)packer 1.3 to edit.
As you opening post says french 2.2.1 and I cannot find that on the page you linked to.
Click to expand...
Click to collapse
Sorry thats a typo, it should be 2.1.1
Hello,
I have a big problem. I misplaced my MS2 with a customrom Droid 2 installed. after which the phone is stuck at Moto logo, I wanted to flash it with RSD Lite again. But unfortunately it has made all the worse. The screen then remained always black. By accident I found out that the master is always handy in the bootloader if I make the battery clean. the RSD Lite detects it again and then when I want to flash an SBF file he does it without problems. only then if he should make a reboot it ends up back in the bootloader. but i can´t see the bootloader. I know not what to do yet.
can anyone help me?
thank you
greeting
I didn't get quite right the situation but tell me which sbf are you using?
Is it the same android version that was before?
Have you tried pulling off the battery, waited 10 seconds, hold vol + and vol - (or X and arrow up, depending on android version) and powering up to enter the recovery and do a full data wipe? Does it starts normally after that?
Yes, it is the same as before sbf. I've been on it before GB and GB have also flashed.
at the first flash of sbf I'm also in the recovery menu and have a full wipe made but which has unfortunately not have shown anything.
I thought that maybe Customrom a different bootloader has been on it so I downloaded the 70.13 bootloader and flashed.
Since then I have the problem that it only comes into the bootloader, and here again but I have only a black screen.
greeting
sir my advice is redownload your SBF.. maybe it got corrupted. and make sure you choose the right SBF.
devilbatghost said:
sir my advice is redownload your SBF.. maybe it got corrupted. and make sure you choose the right SBF.
Click to expand...
Click to collapse
hi Devilbatghost,
i redownload the SBF and its the right SBF.
i send it to Moto to fix it.
thanks for all.
greet
Original Milestone 2 SBF files
Can someone please tell me where I can get these original SBF files for my M2? I want to go back to the stock ROM for my phone.
Here:
http://and-developers.com/sbf:milestone2
the links for the sbf files are dead.
yes
those links are dead.
does anyone know of an alternate location for the sbf files?
xsghost said:
those links are dead.
does anyone know of an alternate location for the sbf files?
Click to expand...
Click to collapse
Check here for the name of the file you want to download
http://and-developers.com/sbf:milestone2
And download from here the ROM you want
http://sbf.system-ready.org/umts_milestone2/
I have trouble getting the sbf file too, all the links given are dead and i cant reach it from anywhere else, would anyone be kind enough to share the UK 2.2 sbf file?
http://sbf.droid-developers.org/umts_milestone2/list.php
Sent from my A953 using XDA
I recently got a Flipside abroad from ebay and its an AT&T One, I don't have warranty
It was Working nice with some proplems like the touch freezes and apps stop working frequently but it was OK
my cell don't read arabic so i searched how to add the arabic reading and found one, i had to input framework.jar and another root file, run an cmd, and then copy the produced .zip to sd to flash it after renaming it update.zip
The Flash failed and then i had to use the manual way they mentioned about copying outputed files into framework and lib folders
My Device is rooted and I used adbd insecure to give Android Commander permission to access root from PC
i exchanged files and rebooted as mentioned, and That's The Proplem, The Phone Skips At The MOTO LOGO and that is always followed by an AT&T animation then it starts, but the phone is freezed at the Moto Logo, and i tried removing/placing battery, let it to empty charge then charge it
And to restore factory settings through the Recovery mode but the same problem occurs
PLEASE HELP QUICKLY! as i Cannot Use my phone, Its Android 2.2.2 Froyo
yosry93 said:
I recently got a Flipside abroad from ebay and its an AT&T One, I don't have warranty
It was Working nice with some proplems like the touch freezes and apps stop working frequently but it was OK
my cell don't read arabic so i searched how to add the arabic reading and found one, i had to input framework.jar and another root file, run an cmd, and then copy the produced .zip to sd to flash it after renaming it update.zip
The Flash failed and then i had to use the manual way they mentioned about copying outputed files into framework and lib folders
My Device is rooted and I used adbd insecure to give Android Commander permission to access root from PC
i exchanged files and rebooted as mentioned, and That's The Proplem, The Phone Skips At The MOTO LOGO and that is always followed by an AT&T animation then it starts, but the phone is freezed at the Moto Logo, and i tried removing/placing battery, let it to empty charge then charge it
And to restore factory settings through the Recovery mode but the same problem occurs
PLEASE HELP QUICKLY! as i Cannot Use my phone, Its Android 2.2.2 Froyo
Click to expand...
Click to collapse
Reflash stock sbf with rsd is my only suggestion. Here's the stock sbf
http://db.tt/H2RuCD8h
What?
pre4speed said:
Reflash stock sbf with rsd is my only suggestion. Here's the stock sbf
Click to expand...
Click to collapse
Sorry it may look like i'm a noob, but what is "Stock Sbf with rsd" ??
I done it with another sbf and success but now i'm stuch in that stupid bootloader , can you tell me how to get into the stock recovery from my flipside to wipe/data? as i cannot get of that bootloader
yosry93 said:
I done it with another sbf and success but now i'm stuch in that stupid bootloader , can you tell me how to get into the stock recovery from my flipside to wipe/data? as i cannot get of that bootloader
Click to expand...
Click to collapse
after flashing sbf file, no need to wipe data, if you stuck at some where, reflash the sbf file.
phapsubongtoi said:
after flashing sbf file, no need to wipe data, if you stuck at some where, reflash the sbf file.
Click to expand...
Click to collapse
I reflashed it 3 times , Still stucked on that Bootloader !!
yosry93 said:
I reflashed it 3 times , Still stucked on that Bootloader !!
Click to expand...
Click to collapse
Prolly need the bootloader for froyo as well. Sorry shoulda gave you that too.
Flash bootloader first then the sbf. All done via rsd
Froyo bootloader http://db.tt/FuXac7kG
Seems to be my falt
pre4speed said:
Prolly need the bootloader for froyo as well. Sorry shoulda gave you that too.
Flash bootloader first then the sbf. All done via rsd
Froyo bootloader
Click to expand...
Click to collapse
Ok i flashed it . and flashed the sbf i'm using agian
SAGE_U3_10.23.20_SIGNATT_USASAGE02B25ND0ATTNA02E.0R_PDS001_SAGEATT_P033_HWp4_1FF.sbf
but the same problem, should i use the SBF u told me about or any other??
The SBF i used is also for Flipside, the rsd says successful, and PASS is the result but still stacked in that Bootloader whatever i rebooted using power button or replaced the battery, known that i cannot open Recovery (X+Power Button) to wipe data
Thank You
Thank You very much body, i used the SBF you gave me and it worked well, my phine is now working again
Thank Youuu
yosry93 said:
Thank You very much body, i used the SBF you gave me and it worked well, my phine is now working again
Thank Youuu
Click to expand...
Click to collapse
You are quite welcome. Been so long since I've used or looked at my flopside (no typo lol) that I had forgotten froyo needed the updated bootloader first. Glad its working again.
Hi,today I have flashed original Motorola .sbf ,I downloaded it from here. It is 3.4.2_179-002, Retail Central Europe version. Now,after flashing it with RSD Lite the phone does not boot. There is no even Motorola logo at the start,nothing,its dead. How can I start the phone with this original .sbf? I want to have original froyo on the phone,and I know how to get back to CM10 but im not interesting in that now.
Thanks.
markos807 said:
Hi,today I have flashed original Motorola .sbf ,I downloaded it . . .... I know how to get back to CM10 but im not interesting in that now.
Thanks.
Click to expand...
Click to collapse
markos807, did the SBF flashing process complete successfully and did u get the message "Please manually reboot phone" in RDSLite window?
Did u verify the MD5sum of the downloaded SBF against the MD5sum given in the download page to check if the downloaded SBF file is not corrupted?
Are u still able to go to the Bootloader by pressing VOL UP+POWER button when the phone is switched off?
Only if u provide the above information, I can suggest what can be done next.
1.I dont remember what was the message,but I think it wasnt "Please manually reboot phone",but it was done,some other message saying its done
2.How to do that?
3.I cannot go into bootloader and when I connect a phone via usb to the PC the RSD Lite recognizes it so I can flash some other verified sbf.
Thanks for trying
markos807 said:
1.I dont remember what was the message,but I think it wasnt "Please manually reboot phone",but it was done,some other message saying its done
2.How to do that?
3.I cannot go into bootloader and when I connect a phone via usb to the PC the RSD Lite recognizes it so I can flash some other verified sbf.
Thanks for trying
Click to expand...
Click to collapse
Might I suggest, pull your Defy battery, replace it, do not attempt to get into bootloader, Leave it off. Just plug it in with usb after booting up RSD lite and see if connects on it's own. Sounds like a bad flash. I've connected that way numerous times.
markos807 said:
1.I dont remember what was the message,but I think it wasnt "Please manually reboot phone",but it was done,some other message saying its done
2.How to do that?
3.I cannot go into bootloader and when I connect a phone via usb to the PC the RSD Lite recognizes it so I can flash some other verified sbf.
Thanks for trying
Click to expand...
Click to collapse
1. Even I dont remember the exact message But I remember that it asks us to reboot the phone manually.
2. If the SBF which u are using is corrupted while downloading, it may lead to bad flash. U can google and download and use any of the md5sum checking tools. I use winmd5 application(I'm using Windows in my laptop), which is easy to use and it has UI unlike some other md5sum tools which have to be run through command line.
3. If RSD Lite recognizes ur phone, then try flashing the SBF once again. But ensure that the SBF is not corrupted as mentioned in point 2. If ur SBF is corrupted, try downloading it again. There are chances for a file to get corrupted while downloading. That is the reason why md5sum is mentioned in the download page to verify the file after download.
Winmd5 app says "Matched!". That means it is good?
Yes, if the MD5sum matches it means that the SBF file is not corrupted. U try flashing the same SBF again and see if it works.
@ markos807: Were u able to flash SBF successfully? I would like to know if ur defy is working fine now
Gingerbread (BL7) back to Froyo?
Did you already flash a Defy+ ROM with Gingerbread?
From a BL7 ROM there is no way back to Froyo. BL7 doesn't support that.
When I wanted to go back to froyo, I was flashing this sbf: JDGC_U6_2.13.0 China Unicom Thread/Download !!!BL6 kernel !!!
And that broke my flashlight! And because of that I want to go back to other official froyo sbf to see will the flashlight work. Do you know any other fix for the flashlight? Anything please?
Also, I am flashing same sbf second time now, will post the results.
Edit: Cannot boot the phone with any .sbf downloaded from here. The only .sbf that I can flash and boot the phone is JDGC_U6_2.13.0 China Unicom and that one broke my flashlight.
markos807 said:
When I wanted to go back to froyo, I was flashing this sbf: JDGC_U6_2.13.0 China Unicom Thread/Download !!!BL6 kernel !!!
And that broke my flashlight! And because of that I want to go back to other official froyo sbf to see will the flashlight work. Do you know any other fix for the flashlight? Anything please?
Also, I am flashing same sbf second time now, will post the results.
Edit: Cannot boot the phone with any .sbf downloaded from here. The only .sbf that I can flash and boot the phone is JDGC_U6_2.13.0 China Unicom and that one broke my flashlight.
Click to expand...
Click to collapse
Mate, as you flashed BL6 sbf then you are stuck with BL6 and no way back to froyo other than chinese one.
Your flashlight could be burnt out - in such a case only moto service can help
What do you mean you cannot boot with any sbf from walter79 thread? Have you tried all of them? (You shouldn't). Or only froyo ones?
If you tried only froyos, then you can flash gingerbread BL6 to check your flashlight
And have you tried wiping data and cache from stock recovery? Is it accessible with power + volume down?
No, I cannot acess stock recovery. I have tried only froyo ones. Can you give me the link for that BL6 GB, I`ll flash it tomorrow because I really want to fix my flashlight.
markos807 said:
No, I cannot acess stock recovery. I have tried only froyo ones. Can you give me the link for that BL6 GB, I`ll flash it tomorrow because I really want to fix my flashlight.
Click to expand...
Click to collapse
Try any from a range 4.5.1-134_DFP-125 up to DFP-161. Higher are usually BL7, lower are BL5, so no use to flash
Link to the sbfs
I have succesfully boot up a phone with this sbf: DEFYPLUS_U3_4.5.1-134_DFP-125_GR_SIGN.. but my flashlight is still not working. The camera is not working at all.
markos807 said:
I have succesfully boot up a phone with this sbf: DEFYPLUS_U3_4.5.1-134_DFP-125_GR_SIGN.. but my flashlight is still not working. The camera is not working at all.
Click to expand...
Click to collapse
Well, I suppose you've burnt your flash unfortunately with chinese froyo.
Your camera will not work with GB ROMS. It's normal. but it was you who flashed BL6 ROM on your green defy
You have to go to CM10 2ndboot builds to have your camera working again.
For flash I suppoose only moto service can help