Related
So I was pretty careless and dropped my N1 in work, landing perfectly on it's screen It still functions perfectly and the AMOLED screen hasn't been damaged, simply the digitizer. I've already ordered a new one with all the tools necessary to replace it, but I'm yet to find any definitive guide on replacing the N1 digitizer.
I came across thread #751923 (Can't post links as I'm new) which seems really helpful but a guide with pictures/video would be awesome. There's a 45 step youtube vid on how to replace it as well but the quality/clarity isn't great. I'm sure I can use both of these to replace it just fine, It just seems a little daunting.
Basically I'm looking for consolation along the lines of 'It's damn easy to fix' Any love for a fellow N1-er?
It is easy to fix. Two tips: don't use metal spatulas to pry the plastic under the battery off and gently wiggle and push the motherboard out only after disconnecting all the little connectors on it.
Im also waiting on my digitizer. I'm going to folllow these 2 guides.
http://www.ifixit.com/Teardown/Nexus-One-Teardown/1654/1
http://cnn.cn/shop/google-nexus-digitizer-p-8252.html
Have done it and you actually found better tear-downs and tutorials. Use youtube as well. The videos help because they show the techniques as well. Hardest part i would have to say is sliding the motherboard out the bottom under the metal separator. I think it was great and taught me a lot about my phone. The thing you have to watch out for is dust and fingerprints under the screen. Once it's on...it's on, anything underneath is stuck lol. make sure it's all clean and you won't have any annoyances like dust particles like i have.
I did it, mostly successful. I damaged the cable to the trackball, so be careful at that step, otherwise nothing difficult, just takes an hour or so.
Cheers for the info and advice guys, should hopefully get my replacement digitizer tomorrow so I'll keep this thread updated with the outcome
I have replaced my digitizer. It cost me $45.00. It was challenging but not impossible. The hardest thing is not tearing any of the ribbons when dissasembling. It was a successful replacement. The only gripe I had was the digitizer I bought did not come with the adhesive to glue the digitizer to the frame. Make sure you have a way to attach the screen to the frame before you begin the process. Other than that it should be easy as long as you take your time.
Sent from my Nexus One using XDA App
I replaced mine.. it took a solid hour or so, just be very careful not to tear any of the ribbon cables.. everything is super small and delicate.
I now get lots of dust in the corners of my screen because i didn't seal the new digitizer properly, but its not a huge deal to me.
replacing the digitizer is easy... its taking apart, and putting the rest back together that sucks. just make sure you know what length screw goes in what hole... very important. take notes as you disassemble.
nexusonemeover said:
just make sure you know what length screw goes in what hole... very important. take notes as you disassemble.
Click to expand...
Click to collapse
haha reminds me of when I took my laptop apart to re apply thermalpaste. I ended up with 7 extra screws >.< But the thing was together and has been running fine for the last 6 months so O.O
I did it, not too bad if you go slow and deliberately. I also have dust under my screen now. I sort of wish I would have just sent it to HTC but the money saved is worth a little dust.
A useful tip for disassembling is to cut out a paper template the same shape as your N1 and push the screws through it in positions corresponding to the screw holes in your N1. Its much easier to figure out where they all go when you come to reassembling it, just dont knock your template and screws on the floor .
rob61280 said:
A useful tip for disassembling is to cut out a paper template the same shape as your N1 and push the screws through it in positions corresponding to the screw holes in your N1. Its much easier to figure out where they all go when you come to reassembling it, just dont knock your template and screws on the floor .
Click to expand...
Click to collapse
That's a great idea, rob. I always think whenever I take apart a phone that I should have a video camera handy to record what I'm doing so I can play it in reverse when I'm putting it back together
For $115 you can send your phone back to HTC and have a QUALIFIED technician replace your screen.
Yes, it's a little more but you don't have to worry about messing anything else up and you're getting back your phone without any installation flaws.
Well I eventually got my digitizer this morning. It took until I had everything taken apart to realise they had sent me a compatible but ill fitting digitizer. It doesn't even have the appropriate buttons (it did in the selling image) at the bottom. At this point everything works fine but it doesn't look perfect. I guess it'll have to do, thanks for the advice guys
omgdwong said:
For $115 you can send your phone back to HTC and have a QUALIFIED technician replace your screen.
Yes, it's a little more but you don't have to worry about messing anything else up and you're getting back your phone without any installation flaws.
Click to expand...
Click to collapse
Wow thats cheap, I just got quoted for around $300US to fix my phones screen.. not including labor.. argh
Does anyone know if HTC in america repair phones from the other side of the world even though they were purchased from google's store?
I just sent my phone into HTC to be repaired for a cracked screen expecting it to be $115 and was pleasantly surprised to find that it would only be $55 including shipping! HTC was also extremely quick to get back with me for the quote. I sent the phone out Tuesday at 4pm and they have looked at it and quoted me the repair cost by Wednesday at 2 pm.
I recently cracked my digitalizer as well.
I called HTC 2 times without giving any information about myself before calling a 3rd time to do the actual swap.
I was quoted at $115 for me to send in my N1, wait a week without a phone, and have them replace the digitalizer, before shipping it back.
I then further inquired and found out they have a Swap program where they mail you a new(refurbished, but perfect) phone, and a FedEx label, which they still quoted me $115 to fix the screen, and a possible $275 if they needed to replace the logicboard, but they would get a quote back to me with all the things they would need to replace. It would require a $529 charge to my card, incase i didnt send the phone back at all.
I mentioned that my camera was broken, as well as my trackball was loose, and he said the quote would include this as well.
I called back a 3rd time, requested a swap phone, and had one 2 days later.
i mailed my phone into HTC, and two days later i had my quote.
I paid $55 after it was said and done, and have a new (refurbished) phone
I was rooted,unlocked, and running Kang-O-Rama 1.0 when i shipped the phone in. I didnt bother to fix that.
Has there been a decent guide on taking the 4G apart yet? I've googled it but haven't been able to find anything yet.
kitsunisan said:
Has there been a decent guide on taking the 4G apart yet? I've googled it but haven't been able to find anything yet.
Click to expand...
Click to collapse
I cant fine one either but there are 2 screws in the battery compartment and it looks like the metal portion where the camera is may pop or peel off with a little force. My guess, try to remove metal portion where camera is, if it comes off and exposes screws remove those along with 2 in bat compartment then use tool to try and separate where bezel and rubber surround are. Just fumble it.
May I ask why your taking it apart?
Stupid reason really, I was going to see if the ffc could be centered better. Seems just about all of the MT4G phones have an off-centered camera, and wanted to see if I could move it back to center myself. I was just curious to see what was throwing it off.
I had the two screws off last night, but couldn't get anything to come off. Didn't want to force it and break anything, I was just hoping a teardown had been done showing what needed to be done.
kitsunisan said:
Stupid reason really, I was going to see if the ffc could be centered better. Seems just about all of the MT4G phones have an off-centered camera, and wanted to see if I could move it back to center myself. I was just curious to see what was throwing it off.
I had the two screws off last night, but couldn't get anything to come off. Didn't want to force it and break anything, I was just hoping a teardown had been done showing what needed to be done.
Click to expand...
Click to collapse
I don't think a phone exists that you dont have to pry, push, pull and force things to get them apart. There will ALWAYS be risk of breaking things when taking a phone apart. I would just deal with it and not open the phone. Plus, they usually have a way to tell if you've opened your phone so you will void your warranty.
There is a "void" sticker on one of the screws. If someone does open her up, check to see if you could replace the speaker with a better one from another phone.
Please post questions in Q&A section.
I'm curious to learn how to take the phone apart as well, because I'd like to figure out how to make the damn buttons stop squeaking & clicking so loudly (home/menu/back/genius). It's driving me insane and I'm already on my third MT4G.
dustrho said:
I'm curious to learn how to take the phone apart as well, because I'd like to figure out how to make the damn buttons stop squeaking & clicking so loudly (home/menu/back/genius). It's driving me insane and I'm already on my third MT4G.
Click to expand...
Click to collapse
Anyone? I'm now on my fourth MT4G and will be receiving a fifth one shortly (creaking buttons), and if I experience that same problem I'm thinking about trying to fix the damn thing myself.
damn still no tear down i need one buttons jammed
I tore one apart after I got pissed and threw it into the hardwood floor at full speed.
I don't remember the steps but I do remember there are a couple key points, including ribbons that have to be disconnected. The ribbon connector from the main display to the main board is junk and that, of all places, is where my tear down went south.
I've got 450.00 dollars sitting in pieces if anyone wants to see them.
Sent From My Rooted HTC Glacier- It Just Makes SENSE
pdxrealtor said:
I tore one apart after I got pissed and threw it into the hardwood floor at full speed.
I don't remember the steps but I do remember there are a couple key points, including ribbons that have to be disconnected. The ribbon connector from the main display to the main board is junk and that, of all places, is where my tear down went south.
I've got 450.00 dollars sitting in pieces if anyone wants to see them.
Sent From My Rooted HTC Glacier- It Just Makes SENSE
Click to expand...
Click to collapse
I'm looking to buy someones Part "Power Ribbon Cable Assembly" (The part thats connected to the power button) *BE CAREFULLY" Everything has to be in Working order and not torn! Send me photos of the part I'm looking for and price. [email protected] Thanks!
dustrho said:
Anyone? I'm now on my fourth MT4G and will be receiving a fifth one shortly (creaking buttons), and if I experience that same problem I'm thinking about trying to fix the damn thing myself.
Click to expand...
Click to collapse
You must never have had a MT3G. These buttons are a dream compared to the creaky clickers in that dog.
I bought a refurbished phone on Craigslist and there are fingerprints on the inside of the glass (I don't know why I never saw them when I was inspecting). Would like to teardown guide so I can go clean those prints off.
Lil bit of thread necromancy here, but did anybody ever find a teardown? I'm thinking of ripping mine open due to my backlight issue ( http://forum.xda-developers.com/showthread.php?t=958033 ). I guess if nobody else has a teardown, I'll have to brave the waters and post my own, but going in blind is going to increase the risk of me killing the thing even worse than it already is
I'm also preparing to replace my digitizer. I came across a couple recent tear-down videos:
http://forum.xda-developers.com/showthread.php?t=961252
http://www.repairsuniverse.com/htc-tmobile-mytouch-4g-take-apart-repair-guide.html
Good luck!
Phew. Just replaced my digitizer using the latter video. Putting it back together was fairly straight-forward by just following the video backwards, though a 'put back together' video would be convenient.
A couple minor caveats:
They skipped showing some phillips screws holding the motherboard in place (near the end). I think there were two of them. They're fairly obvious if you know to look for them.
I attempted to reuse the existing adhesive by reheating and applying pressure. This sort of worked, but the digitizer seems a tad loose. I don't think it's going to fall off, but it'd probably be better to remove the old adhesive and apply some fresh adhesive. Anyone know where to get a suitable adhesive?
Taking apart the MyTouch 4G is not that hard
I bought a used MyTouch 4G in pieces on Craigslist for $ 45 that had a broken digitizer (about $ 20 on eBay with free shipping) and LCD (about $ 40 on eBay with free shipping) and the Audio & Volume Button Flex Cable (about $ 38 on eBay with free shipping) was also defective (the power button cable was ripped which can happen very easily if you take the phone apart and if you are not 100% careful when you pry the power button cable out). I ordered all the replacement parts on eBay from US sellers.
This particular phone had the "bad", washed out screen and was manufactured in Taiwan. When I ordered the replacement LCD and digitizer, I was hoping to get the "good", bright and superior screen but that didn't happen. So for the ones out there who are hoping to improve the screen by replacing the LCD and/or digitizer, it's a 50/50 shot.
I also ran into the problem with the adhesive and found a roll of 3M 2mm double sided tape for $ 10 with free shipping on eBay. The phone is working great and looks like nothing ever happened now after I put it all back together. And even though I had to pay for a lot of replacement parts, it was still a lot cheaper than buying a new one from T-Mobile or a used one on Craigslist or eBay
There are also a lot of MyTouch 4G disassembly videos on youtube. I'm a gal and if I can do it, you can too !!
EDIT
"meyourchum" has provded a link to get offical disassembly instruction with lot more information.
Check it for yourself
Hello folks,
I had a chance to work on my friends arc who bought a Rogers version and dropped it. He had it totally mess on the case and needed the full housing replacement.
I hope that doesn't happen to anyone. I didn't take any photos but I am trying to explain everything as it was to help anyone with this.
General Note:
- Anywhere you got stuck, watch some X10 Disassembly video
- Be very gentle to your phone in this process
- Besides all the screws the rest of the phone is put together with glue(Sticky Back) and snap(plastic for main board)
- Using this information on your own risk as I don't take any responsibility if anything happens to your phone.
Instruction
1) Remove the back battery cover. Thats the easiest part
2) Need star shaped screw driver[Trox](I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny) This is what I bought
All the above we all have seen them
3) After removing the 6 screws remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
4) Main board is snapped in with plastic to the body which easily can be opened.
5) Little board on the bottom is glued(sticky back @ top) which you can remove with pulling little hard but make sure you don't break it.
6) Majority of the wire you see connected to mainboard can be discounted (snap in wires)
7) Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
8) if you are doing a full housing replacement, then there are stuff here and there that you need to remove and re-use it on the new housing(Like 3.5 mm jack, HDMI lid, etc.)
Good Luck and let me know if you have any questions.
1st time... ehm.. taking the Arc apart, that is!
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz
Hope u have the courage to make a video next time
Sent from my Arc using XDA premium App
xelion said:
Helluw there
Just read your post, and thought I wanted to share with you, that I might be opening one of these slick little things. My friend broke his display, and the ISP is talking about some 'off the scale' repair prizes.
...So, he asked me to do the job
Told him I didn't have any experience on the disassembling of this phonetype, but he trusts me it seems
I might return with some questions in case of problems, is that OK with you Nimche?
Greetingz
Click to expand...
Click to collapse
Sure, no problem. I would be more than happy to answer. Lets see just some general stuff...
Note: anywhere you got stuck, watch some X10 Disassembly video
Note: be very gentle to your phone in this process
- you remove the back battery cover. Thats the easiest part
- you need that star shaped screw driver(I bought the set for $5) there are 4 screws like that and two which opens with phillips screwdriver(tiny)
All the above we all have seen them
after removing the 6 screws
note: besides all the screws the rest of the phone is put together with glue and snap(plastic for main board)
- remove the front fascia of the phone with a guitar picks, something skinny but sturdy*
* I recommend not using anything other than rubber or plastic in the whole process.
- main board is snapped in with plastic to the body which easily can be opened. I change full housing and not sure if you have to remove the hard key button from the bottom end of the phone too or not but that little board on the bottom is glue which you can remove with pulling little hard but make sure you don't break it.
- All the wire you see connected to mainboard can be discounted (snap in wires)
- There is a big one which goes to the screen you have to dis-attach that before removing the screen
- Removing the screen: from outside of the phone (like you are looking directly to screen like you normally do) you need to put something under neat and raise up the screen. This part has glue as well and its hard to lift but I did it and it should be possible.
Good Luck and let me know if you have any questions.
Can you answer this??? It get's hot here (and also in the same spot on the front.. so what's inside at this point??
CPU is right behind the second cover. I wish I could take some photos.
Nimche said:
CPU is right behind the second cover. I wish I could take some photos.
Click to expand...
Click to collapse
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .
Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?
hellocng said:
Can I change only the front faceplate around the screen without removing the mainboard? How easy would that be? I want to change mine to Misty Silver as Rogers only carry the Midnight Blue.
Also, for glued parts, do I have to glue them back on the new housing?
Click to expand...
Click to collapse
Glue part, they are more sticky than glued. You just simply stick it back where it was.
Where is the silver face you found?
This is retarded from them...
Digitizer and screen(one part) are sticked to the front face. In order to for your to change the faceplate only(front) you may have to go through the whole process because the wires from digitizer are going through a big hole to the main board. You don't want to mess around with $700 or $800.
Inside, everything is small. really small. I thought I totally screwed up the whole thing. Technology has gone forward alot since I was a kid putting radio together.
Good Luck
prathaban said:
Thanks for the clarification. I was also suspecting since this area gets damn hot when playing games and even at charging (sometimes).
So seems like they move the CPU from behind the battery in X10 to near to the camera in Arc .
Click to expand...
Click to collapse
Yes, there are two board one above battery and one below batter @ bottom of the phone
On top is the main board
on bottom is the board for hard keys.
Nicely put together but they could have done a better job there....
Are there three parts to the housing? I assume there is the front plate, middle housing with the chrome, and the battery cover. The mainboard should be in the middle with the chrome. So I can't just detach the screen front the front plate? What is holding the three pieces of housing together? The six screws?
There are silver housings on eBay from time to time. Though, blue is a lot more common.
Three pieces. Back battery cover which is nothing.
Then there are two main pieces.
Chrome which is more like a holder of the fascia.
If I remember correctly, the front Fascia is the one holding all the board on it including that metal look piece(aluminum probably)
I will take photos and upload here...
Uploaded photos to the first post...
Hey, I'm looking to replace the chrome piece which has a few nasty chips in it, after removing the second back cover, how easy is it to take off that chrome piece?
Great post
How can I replace digitizer? I dropped my phone and the glass cracked
anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.
how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?
soldiers33 said:
anyone know where i can get the tiny screw driver? I cant seem to find the correct one. they are either too small or too big.
Click to expand...
Click to collapse
Sorry, you could have sent a private message.
I bought the screw driver here at local tool shop. Home Depot sells them.
Its called Trox Screw Driver and I bought exactly this one http://www.homedepot.com/webapp/wcs/stores/servlet/ProductDisplay?storeId=10051&productId=100087664&langId=-1&catalogId=10053&ci_sku=100087664&ci_kw={keyword}&cm_mmc=shopping-_-googleads-_-pla-_-100087664&ci_gpa=pla&locStoreNum=618
I don't have the packaging but they should be standard.
Good Luck
mps83 said:
how easy is it to replace the front cover, ive cracked the top of it and chipped a bit out the side (surrounding the screen) i presume it'd be simple enough. And does anyone know where i can get a good quality/genuine front cover replacement?
Click to expand...
Click to collapse
You can find the whole housing between $30 to $40 but the front cover is that actual main piece that holds all the internal components + the screen.
If the crack doesn't bug you much, I would not do it since you have to replace the sticker behind you battery as well, which is not easy to peel off + you have to take the screen off the old front fascia which is glued and kind of hard to take off.
Downside of the whole thing for me was the sticker. I have to find an alternative for this problem.
Ok folks, there's probably a thread on this somewhere, but I haven't found it yet, and frankly I've got plenty to do as it is, so forgive me for not making a thorough search.
Anyhow, I've managed to crack the screen just above the home and app buttons, which is a pain, but **** happens. I've noticed that on eBay the screen + LCD combo is around A$140 while the front glass alone is only A$27. Now, since the Lcd isn't damaged, that kinda looks awesome, right? Except, I haven't found any instructions on how to replace the front glass alone with out ****ing with the LCD too. Anyone know?
Plenty of vids on YouTube on how to change the combo, which is a bit of a pain in the arse compared to other phones. All I want to change is the glass. Any help would be much appreciated.
WestAussie said:
Ok folks, there's probably a thread on this somewhere, but I haven't found it yet, and frankly I've got plenty to do as it is, so forgive me for not making a thorough search.
Anyhow, I've managed to crack the screen just above the home and app buttons, which is a pain, but **** happens. I've noticed that on eBay the screen + LCD combo is around A$140 while the front glass alone is only A$27. Now, since the Lcd isn't damaged, that kinda looks awesome, right? Except, I haven't found any instructions on how to replace the front glass alone with out ****ing with the LCD too. Anyone know?
Plenty of vids on YouTube on how to change the combo, which is a bit of a pain in the arse compared to other phones. All I want to change is the glass. Any help would be much appreciated.
Click to expand...
Click to collapse
use a hairdryer for loosening the adhesive to separate glass and digitizer , being patient is the key but there is a good chance of messing it up
It was my understanding that the screen assembly was next to impossible to disassemble without damaging the other layers of the screen. It seems hard enough to separate from its housing I can't imagine the difficulty in de-laminating the glass from the digitizer/LCD.
I just replaced my front with the combo part from etradesupply it was pretty expensive but 0 hassle. A couple of screws later and I moved to the old main board to the new front part... No heating no heavy prying.
Good luck with your fix.
P
pietro_spina said:
It was my understanding that the screen assembly was next to impossible to disassemble without damaging the other layers of the screen. It seems hard enough to separate from its housing I can't imagine the difficulty in de-laminating the glass from the digitizer/LCD.
I just replaced my front with the combo part from etradesupply it was pretty expensive but 0 hassle. A couple of screws later and I moved to the old main board to the new front part... No heating no heavy prying.
Good luck with your fix.
P
Click to expand...
Click to collapse
Didn't you have to heat the battery to move it when you did the swap? My fear is ill damage one of those wafer thin ribbon cables in the process too. Just looks like a mission of a job from the vid I watched on YouTube. Would hate know how much a tech guy would charge though.
Sent from my Nexus 4 using xda app-developers app
WestAussie said:
Didn't you have to heat the battery to move it when you did the swap? My fear is ill damage one of those wafer thin ribbon cables in the process too. Just looks like a mission of a job from the vid I watched on YouTube. Would hate know how much a tech guy would charge though.
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
Mine had a battery.
This is the part I bought.
OEM LG Nexus 4 E960 LCD Screen and Digitizer Assembly with Front Housing and Battery
from this page (they ship out of Hong Kong)
http://www.etradesupply.com/lg/android-models/lg-nexus-4-e960-parts.html but it appears to be out of stock now. (Maybe I got the last one)
Like I said, it was pricey, but i couldn't risk me screwing it up further since I run my architecture firm with this phone. I was looking for a minimal down time solution because the alternative for me was just buy a new phone in a retail store the next day. Not having access to the lower parts of my screen was seriously limiting. I slogged away for a week using all sorts of work-arounds to activate the dial pad, use parts of the keyboard etc while I waited for the replacement part.
This guy http://www.youtube.com/watch?v=AZDAIgwbXk4 does not show the heating stage but he is so freaking calm, it can't be that bad... Do remove the main board before prying on the battery if you go that route...
-p
I just want to add, for anyone finding this thread, that the part I got from etradesupply.com has some pretty obvious yellowing of the screen. This screen was either removed from someone else's n4 because of this defect or taken from the reject bin at the factory.
In the future if I have any breaks, I will sent it to an LG facility.
Does anyone know of another place to buy the front screen with housing? It is OOS at etradesupply....
Just saw this one posted. I have not used them.
http://www.globaldirectparts.com/LG-Nexus-4-s/20969.htm
pietro_spina said:
Just saw this one posted. I have not used them.
http://www.globaldirectparts.com/LG-Nexus-4-s/20969.htm
Click to expand...
Click to collapse
Thanks... looks like mixed reviews about this company, though.
My Ex droped her Phone and it had Spider Webs all accross. Her Provider send it in to see what it would cost to fix. The Phone also would stop working correctly in the middle of calls.
It turns out buying a new one would have come cheaper atleast thats what came back as a answear.
So I decided to bite the apple and try replacing the Screen myself. My Ex was not happy because she thought with the second Problem it is not worth the effort to fix the Screen and maybe loose everything. My reasoning was that when the Spider Web Screen touches the Digitizer it will react strangely. So I went ahead and searched the web on how to do it. I ordered a Screen for $9 on ebay (free shipping) which came with a couple of Tools. More on those later.
One of the first Problems I found was that all instructions that I found showed the beginning and the end. But in the middle how the phone will look like when the glass is finaly taken off, I was unable to find much Information about it. Also doing it Redneck style without Special liquids and or a heat guns was no where to be found.
I decided to just try it. Disasembly is well documented and easy enough to do on this device. Atleast to the Point where most electronics are removed so that you can apply heat without too much problems. I decided on using a blow dryer to heat up the Display. I layed the Blow Dryer on the Counter turned it on and Held the phone up to it. Thinking if my fingers get too hot chances are it is too hot for the Display too.. Might be a little incaccurate to read the temperature like that but hey it worked. But soon after I started to remove the first pieces of broken glass I ran into Problems.
As per instructions I found, I put a Piece of tape accros the Screen so that the individuall pieces stayed ogether. That did not work at all for me. It just made the individual pieces push against the valuable digitizer below it. My next Problem was that the Tools that came with the replacement glass, especially the Little plastic Tools did not hold up to the Job und the tip was soon useless. I had to Switch to a Raizor blade. A couple of times I sliped and hit the Digitizer. Thinking oh well I guess I Need to get a new one. Luckely on the end it all worked out much better then I would have hoped. The left over glue I rubbed mostly off with my finger which worked out nicely. To clean it completely from ist glue took some time. The black rubber allong the side of the phone allso suffered. You might want to look out that that does not get riped out completely. I had enough left over so that the glass would sit on it good enough luckely.
Take a look at these Pictures and remember it works perfectly again for $9. While it is not for everyone to seperate a Glass from a Digitizer it is acctualy less fragile as you might think. The third Picture Shows you how it looked with all the scuff marks from taking off the glass. You can still see a few little marks on the end but hard to notice and much better then before. I am sure next time I will be more carefull and use the blade from the beginning on.
I got more Pictures and will improve this Thread for others that have to go through it. Feel free to PM me if you have any Questions. A list of other resources will also be included. This is only to explain and Show the bare state.
Reserved for links
Additional Screen Replacement Links:
Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk
supreethms said:
Do you know if we can replace the metal frame on the side?
My device is bent. I mean. I fell on a rock with my device in my pocket and the rock directly hit the phone. Luckily I had a hsrd case and the device is still alive.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
You should be able to find a new Frame for a resonable Price. Now to remove the digitizer from the Frame that is another Story. Not sure if it was the Glue or what Held it in place but I could not figure out how to get that out. luckely the two Buttons at the bottom survived the Screen removal and so I did not hat to take the Digitizer out.
Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk
http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.
boomboomer said:
Useful information and explains why repair shops will usually only replace the complete assembly. Read many complaints that those cheap ebay screens are plastic and easily scratched, not genuine gorilla glass replacements?
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
It is definetly cheaper then the original but if you have done it once. Chances are You will be able to do it again much easier. So if the $9 Glass only holds for example a Year. You can just replace it again. Or spend a little more for a original replacement glass.
Now I should Point out if the rubber seal around it gets damaged in the process and if the 3M Tape that should come with the Screen is placed wrong it will Impact the sensitivity of the sreen touches. I guess I did it right because my Ex is happy how it performs and that is saying allot.
madmackem said:
http://www.ebay.co.uk/itm/150998824149?_trksid=p2055119.m1438.l2649&ssPageName=STRK:MEBIDX:IT
I've ordered one of these as mines a bit scuffed and what looks like a small crack in it.
Click to expand...
Click to collapse
If you get down to removing the digitizer from the Frame take a couple of Pictures and post them here.