Related
Hi,
I have a little issue: I HSPL my HD2 no problem with . It's just my phone have a hardware problem & I wanna go back to Original SPL 1.42000. I found the original rom made for my branded handy
extract and rename the .nbh
format sdcard in proper format.
neither in sync nor in bootloader mode. Invalid vendor ID. Rom Upgrade issue for me.
How can I uninstall the HSPL ?
PS/ I tried all words given by bepe and other's concerning issues. I didn't found it. I must sent back my phone soon for warrantly reason...
Did you try to install the ROM from HTC website or did you find an Orange specific ROM?
It is an orange specific rom. cause it is a branded handy.
I even try from HTC website one but no satisfaction. I think it is normal by this one ?
I have a non branded "german" device.
I decided to go back from the HSPL to the stock SPL.
I wanted to flash with the Turkey 1.61 rom to have after this procedure the newest radio 2.07 on it.
I have followed the steps from bepe
But my SD card has a "goldcard" file on it.
Go to the HSPL thread and see my post #383
http://forum.xda-developers.com/showthread.php?t=611433
I have noted down all outputs during flashing.
At least I would give it a try and use a "Goldcard" to get back your original rom.
Hope it helps & Good luck!
dingolino
doudaix said:
Hi,
I have a little issue: I HSPL my HD2 no problem with . It's just my phone have a hardware problem & I wanna go back to Original SPL 1.42000. I found the original rom made for my branded handy
extract and rename the .nbh
format sdcard in proper format.
neither in sync nor in bootloader mode. Invalid vendor ID. Rom Upgrade issue for me.
How can I uninstall the HSPL ?
PS/ I tried all words given by bepe and other's concerning issues. I didn't found it. I must sent back my phone soon for warrantly reason...
Click to expand...
Click to collapse
In addition to what the previous poster described:
One can definitely flash the original ROM using the SD card to uninstall HSPL.
Many people do it by accident...
That being said, one question: Are you sure you have the correct ROM file?
You know, the error you mention only arises if you have to answer "no" to that question.
doudaix said:
Hi,
I have a little issue: I HSPL my HD2 no problem with . It's just my phone have a hardware problem & I wanna go back to Original SPL 1.42000. I found the original rom made for my branded handy
extract and rename the .nbh
format sdcard in proper format.
neither in sync nor in bootloader mode. Invalid vendor ID. Rom Upgrade issue for me.
How can I uninstall the HSPL ?
PS/ I tried all words given by bepe and other's concerning issues. I didn't found it. I must sent back my phone soon for warrantly reason...
Click to expand...
Click to collapse
SD card should be formated FAT32. The original one is FAT16
What does it exactly mean: "One can definitely flash the original ROM using the SD card to uninstall HSPL"
We can uninstall HSPL by loading the .nbh from the official ROM from htc website from fat32 formated sd card ?
If the answer is yes, I have done it many times but no satisfaction.
Yes I use the proper and official htc and/or orange .nbh.
How to get out please.
tictac0566 said:
In addition to what the previous poster described:
One can definitely flash the original ROM using the SD card to uninstall HSPL.
Many people do it by accident...
That being said, one question: Are you sure you have the correct ROM file?
You know, the error you mention only arises if you have to answer "no" to that question.
Click to expand...
Click to collapse
doudaix said:
What does it exactly mean: "One can definitely flash the original ROM using the SD card to uninstall HSPL"
We can uninstall HSPL by loading the .nbh from the official ROM from htc website from fat32 formated sd card ?
If the answer is yes, I have done it many times but no satisfaction.
Yes I use the proper and official htc and/or orange .nbh.
How to get out please.
Click to expand...
Click to collapse
looks like the good way. is the nbh file calla LEOING.nbg in your SD card ?
doudaix said:
What does it exactly mean: "One can definitely flash the original ROM using the SD card to uninstall HSPL"
We can uninstall HSPL by loading the .nbh from the official ROM from htc website from fat32 formated sd card ?
If the answer is yes, I have done it many times but no satisfaction.
Yes I use the proper and official htc and/or orange .nbh.
How to get out please.
Click to expand...
Click to collapse
If you do all steps in the correct way, flashing the original nbh with the SD card will definitely overwrite HSPL with stock SPL.
It has happened to quite a lot of people who were not aware of the fact that this happens when flashing a stock ROM with this method.
When you get a wrong carrier ID error message, you don´t have the right ROM, as the device will only allow to flash ROMs with the correct CID, be it HTC or operator stock ROMs.
Did you check the SPL version after the process with the SD card? If it says 1.42.0000, why don´t you try flashing with the original RUU?
yes confirm
tictac0566 said:
If you do all steps in the correct way, flashing the original nbh with the SD card will definitely overwrite HSPL with stock SPL.
It has happened to quite a lot of people who were not aware of the fact that this happens when flashing a stock ROM with with this method.
When you get a wrong carrier ID error message, you don´t have the right ROM, as the device will only allow to flash ROMs with the correct CID, be it HTC or operator stock ROMs.
Did you check the SPL version after the process with the SD card? If it says 1.42.0000, why don´t you try flashing with the original RUU?
Click to expand...
Click to collapse
I confirm: it happends to me: when I flashed the 1.61 HTC official rom from my SD, it replace the HSPL by the original SPL of HTC.
hi all, just want to share..
stock spl is 1.42 and after hspl 1.42hspl or 1.42.6666 if i'm not mistaken.
if to unsintall this hspl, i use flash using sd card method and it will re write radio and spl back to 1.42.
i also using turkey stock rom, but we cannot flash turkey stock rom using sd card method as it will rewrite spl and will give you error. wrong region. if this happen, in 3 colour mode, run you hspl. when it restart, make sure you push volume down button to get back in tricolour mode. if you not pushing vol down button, it will also boot in tricolour but hspl wont work, happen to me, spl back to 1.42.000. the flash using custom ruu.
just sharing with you guys.
Steve0007 said:
looks like the good way. is the nbh file calla LEOING.nbg in your SD card ?
Click to expand...
Click to collapse
It should be LEOIMG.nbh.
dont forget you might want to use MTTY to do task29 to format the device instead of CustomRUU.exe
tbh you can probably use the RUU from HTC if you have HSPL anyway.
p.s. yeah LEOIMG.nbh - LEOING.nbg made me smile - finger-twister
Okay I have tested restoring SPL1.42.0000 on a vendor-id'd phone.
Tried 2 ways of formatting the SD card:
a. formatting the sd card to FAT32 via Diskdrive mode connected to pc
b. Formatted in HD2 using onboard utility in HD2.
Tried 2 images but not the vendor-id image since I do not have that image.
a. Vendor ROM but in different language
b. Stock ROM HTC
Tried 2 ways of changing SPL back to 1.42.0000
a. Reset + vol down shows a 1 second message "Checking.", after that it immediately goes to the blue-green-red bootscreen showing bootloader 1.42.HSPL
b. From bootloader connect USB to pc and flash using stock RUU.
All combinations of above I can not restore SPL. Must be because HD2 requires correct ROM image + correct vendor-id.
Is there possibly a way to remove HSPL in some way without the original vendor image? Goldcard?
Check out my video on reverting back to stock spl
Its in my signature.
Not sure if its the same for locked devices though, just have a look
[★] said:
Check out my video on reverting back to stock spl
Its in my signature.
Not sure if its the same for locked devices though, just have a look
Click to expand...
Click to collapse
very good manual that is. In video manual is exactly the procedure I did. However the vendor-id'd HD2 won't get to the point where the image can be flashed. It gets to the point up to 1:37-1:38 in your video where the word "Checking..." blinks in an instant. After that it returns to bootloader screen.
So no luck yet
htc12345 said:
very good manual that is. In video manual is exactly the procedure I did. However the vendor-id'd HD2 won't get to the point where the image can be flashed. It gets to the point up to 1:37-1:38 in your video where the word "Checking..." blinks in an instant. After that it returns to bootloader screen.
So no luck yet
Click to expand...
Click to collapse
Oh sorry man
Goldcard also tried and no luck.
Every time I reboot to bootloader it gives the colored screen, proceeds to white screen with blue letters, in an instant shows: "Loading..." ..followed by: "Checking..." ..and then returns to colored bootloader main screen.
edit:
I keep thinking whether it is normal or not that the white screen doesn't show any kind of confirmation that it did actually find any nbh file whether it is valid or not. Maybe it just exits when the nbh is not valid, that may be the case.
However I have now ran the routine a whole lot of times and make zero progress.
Maybe better continue the search for the correct ROM to flash with.
just try one of the official roms posted in the official roms thread. don't try 1.61 - only 1.43/48
I have tried all official roms posted including 1.43 and 1.48 and up without success. The bootloader wouldn't go further after having checked the SD card contents. It did not work at all.
Finally now I bricked (I hope temporarily) my HD2 by trying to install the latest official 2.02 from the RUU.
Strange things have happened here.
I had earlier copied an 148 or so nbh to sd card. Bootloader would't work out as explained in posts above. So after all (with card with 148 nbh still inside) I figured it was time to check what ROM 2.02 would do, since I believe it would overwrite all SPL including HSPL since it is a v2 SPL. At least I hoped.
When I opened the RUU, it did reboot the phone as it is supposed to do with RUU.
Few things happened:
a. The phone booted in bootloader and showed me the white step screen which indicated there was a nbh about to be flashed. This was the nbh on the card!
b. The RUU errored with error 260 that the connection was lost. I have never lost a connection, must be because file on sd card took control.
c. Since connection was lost and the phone wanted a flash from the sd card I pressed vol up to continue update. it did start updating... but at about 9% I got a big triangle /exclamation mark, and HD2 stopped updating.
Reboot. Guess what??? SPL 1.42.0000 in bootloader now. From the nbh on the card.
But NO boot, NO radio .... After all I managed to destroy phone and HSPL.
Had to goldcard my way back in. However, problem solved!
Help!
First time attempt at using HPSL and may have bricked my HD2 :-(
I have a Voda supplied HD2 so can't install the stock ROMs directly...I thought I would be able to do so via HPSL, but it seems not. I was trying to install 1.66 (UK WWE) following the HPSL for dummies guide, and did the following:
- installed HPSL onto HD2, confirmed by going into bootloader
- put nbh file (extracted from stock .exe) onto SD card, named LEOIMG.nbh
- entered bootloader and chose flash option via power button
- flash started (minimal progress)
- within 2mins error showed
- now going into bootloader shows
00028002
Not allow
then..
SPL-1.42.0000 :-(
Upgrade ROM code error Please try again
If I start normally I get a warning triangle.
How can I get my HD2 back from the dead, ideally with 1.66 rather than the crummy Voda 1.43? (can anyone point me at a stock ROM for the voda 1.43, perhaps that would at least unbrick it?)
Help!!!!
*EDIT* Currently downloading the Voda 1.43 image, hoping I can at least get that back and running...if that works will still be keen to find out how to apply stock 1.66 via HPSL (bearing in mind that the CID lock(?) means I can't apply 1.66 on my voda device thru normal means)
CraigBruce said:
(can anyone point me at a stock ROM for the voda 1.43, perhaps that would at least unbrick it?)Help!!!!
Click to expand...
Click to collapse
The 3rd sticky down in the HD2 ROM Development thread is titled, "[REF]Leo Official ROMs" - Click that.
Then click, "Shared folder for shipped Leo ROMs".
The first "box" will have the title "Leo 1.43" under it. Click the hand carrying the folder icon.
You'll be greeted with 3 ROM's, select RUU_Leo_Vodafone_UK_1.43.405.1_Radio_Signed_15.26. 50.07U_2.04.50.22_2_Ship.exe and download it.
Hope that helps.
Good luck with getting your phone back up and running.
Your device is not bricked. I think you have not installed HSPL properly.
Try installing HSPL again. As it seems your HSPL is not installed properly. Follow the following instructions very carefully :
Connect your phone to USB
I think when you boot in by default your device goes into bootloader if not press volume down + power butoon on the same time, your phone will enter tri color bootloader mode.
At the bottom of your screen it shoul show "USB"
Now download the HSPL.zip file(I have attached it here)
Now run HSPL.exe and follow the onscreen insteuctions.(Mostly you have nothing to do it will start installing automatically)
After a while on the screen of your phone a text will appear saying "We hacked it". If this text is displayed then everything went ok. Now confirm by clicking yes on the computer screen and it will finish the process.
All done.
Your phone will restart.
If you want to check that your fone has HSPL then press volume down+power key at the same time. The phone will enter into bootloader and should show "cotullaHSPL".
Now you can install any ROM and it will run properly.
Thanks - had just found that and started downloading as you posted this..fingers crossed! If this works will still be keen on ways to apply 1.66 (stock) to my voda CID locked device.
ankush1492 said:
Your device is not bricked. I think you have not installed HSPL properly.
<snip>
After a while on the screen of your phone a text will appear saying "We hacked it". If this text is displayed then everything went ok. Now confirm by clicking yes on the computer screen and it will finish the process.
All done.
Your phone will restart.
If you want to check that your fone has HSPL then press volume down+power key at the same time. The phone will enter into bootloader and should show "cotullaHSPL".
Click to expand...
Click to collapse
This is exactly what happened 1st time I installed HSPL...however trying it again did get the phone back and apparenty healthy again....thanks!
So - 2nd attempt to flash the 1.66 ROM, same as before. Confirmed HSPL installed via tri-colour bootloader screen, selected (via power button) option to flash from SD. Progress bar gets to (max) 10%, Warning triangle briefly shows then phone goes back to tricolour bootloader (but with std. SPL version) and nothing more happens.
Should I be waiting longer ? i.e. is the phone potentially still flashing when on the tricolour, std. SPL, screen ? Not flashed an HD2 before so not 100% sure I'm doing this right..will double check videos on this site, sure I'm just being stupid/impatient/not read enough....may try downloading the ROM again incase corrupted.
Anyway, HSPL installed for 3rd time and phone appears fine back running with 1.43.
People please read the HSPL thread properly, once you have installed the HSPL you CANNOT install from SD card you HAVE TO USE THE PC to install any rom images that are not original HTC.
CraigBruce said:
This is exactly what happened 1st time I installed HSPL...however trying it again did get the phone back and apparenty healthy again....thanks!
So - 2nd attempt to flash the 1.66 ROM, same as before. Confirmed HSPL installed via tri-colour bootloader screen, selected (via power button) option to flash from SD. Progress bar gets to (max) 10%, Warning triangle briefly shows then phone goes back to tricolour bootloader (but with std. SPL version) and nothing more happens.
Should I be waiting longer ? i.e. is the phone potentially still flashing when on the tricolour, std. SPL, screen ? Not flashed an HD2 before so not 100% sure I'm doing this right..will double check videos on this site, sure I'm just being stupid/impatient/not read enough....may try downloading the ROM again incase corrupted.
Anyway, HSPL installed for 3rd time and phone appears fine back running with 1.43.
Click to expand...
Click to collapse
Yeah, the 1.66 ROM you've downloaded may be corrupted. And next time, try installing the ROM with USB connection and the ROM's .exe file. You SPL is reverting back to stock, so it's possible that the culprit is flashing with SD.
OK, problem solved...
Rather than installing the stock ROM via HSPL bootloader I installed HSPL and then ran the RUU exe for the stock ROM. Phone now upgraded
dragon_soft said:
People please read the HSPL thread properly, once you have installed the HSPL you CANNOT install from SD card you HAVE TO USE THE PC to install any rom images that are not original HTC.
Click to expand...
Click to collapse
Thats not true, you can flash custom roms with hspl from an sd card
see my video *here*
dragon_soft said:
People please read the HSPL thread properly, once you have installed the HSPL you CANNOT install from SD card you HAVE TO USE THE PC to install any rom images that are not original HTC.
Click to expand...
Click to collapse
[★] said:
Thats not true, you can flash custom roms with hspl from an sd card
see my video *here*
Click to expand...
Click to collapse
I believe Dragon Soft was possibly referring to not using a stock ROM from SD? If I remember correctly flashing a Stock ROM from SD with HSPL on will remove HSPL.
So in other words, if you have HSPL and want to have a stock ROM, it is best install it from the PC when connected via ActiveSync as this won't affect the HSPL.
Custom ROM absolutely no probs with flashing from SD, the HSPL will stay intact, good work on the video ★
CraigBruce said:
OK, problem solved...
Rather than installing the stock ROM via HSPL bootloader I installed HSPL and then ran the RUU exe for the stock ROM. Phone now upgraded
Click to expand...
Click to collapse
Ok. I think you were trying to install official ROM. When you install an official rom your bootloader will revert back to SPL...
dragon_soft said:
People please read the HSPL thread properly, once you have installed the HSPL you CANNOT install from SD card you HAVE TO USE THE PC to install any rom images that are not original HTC.
Click to expand...
Click to collapse
thats not true. After HSPL you can intall directly from sd card..I have done it almost 100 times.
Ibb1982 said:
I believe Dragon Soft was possibly referring to not using a stock ROM from SD? If I remember correctly flashing a Stock ROM from SD with HSPL on will remove HSPL.
So in other words, if you have HSPL and want to have a stock ROM, it is best install it from the PC when connected via ActiveSync as this won't affect the HSPL.
Custom ROM absolutely no probs with flashing from SD, the HSPL will stay intact, good work on the video ★
Click to expand...
Click to collapse
Well if he does mean that then fair enough, I just thought that he meant custom when he said "that are not official" but whatever, sorry for the mis understanding
Ibb1982 said:
So in other words, if you have HSPL and want to have a stock ROM, it is best install it from the PC when connected via ActiveSync as this won't affect the HSPL.
Click to expand...
Click to collapse
I got my Leo two days ago, went home, put HSPL on it in the first place, wanted to upgrade the stock ROM, and ended up same as CraigBruce. Really frustrating, thought I'd bricked it. So I re-flashed HSPL and this time a custom ROM and it was back up again.
Now I know that I should have flashed the stock ROM via ActiveSync and not SD card which would have left the HSPL intact. I will definitely remember that for the future
just remember that some people WANT to remove HSPL when installing a stock ROM - e.g. when returning device.
tbh it should have worked with stock ROM and sdcard as leoimg.nbh - it is the way listed in HSPL thread to uninstall after all!!! we dont always want to use customRUU!!!
As from the noob flashing thread
NOTE: The only way to remove the HSPL is to flash an original SPL from microSD card
* You can also use this method to flash back your Stock Rom and Stock SPL that you originally had on your phone*
VIDEO TUTORIAL: [★] has made a YouTube video to walk people through flashing a Stock SPL via activesync. Find it *HERE*
- Download a shipped Rom from *HERE*
- Rename the extension to .zip
- open it with winzip and extract the RUU_signed.nbh file to a folder
- Rename it to LEOIMG.nbh and copy it to the root of a microSD card thats been formatted to FAT32
- Insert your storage card into your phone
- Enter Bootloader and follow onscreen instructions to flash
Click to expand...
Click to collapse
Guys, I had reached the exact same issue with the NOT ALLOW problem. And people, we do read some times (the newbies) and nowhere but here you say that AFTER HSPL YOU MUST NOT UGPRADE FROM MEMORY CARD!!!! And NO it is not included inhere: http://forum.xda-developers.com/showthread.php?t=609477
Cheers,
and thanks to all the smart people inhere!
D
thug_life_inc said:
Guys, I had reached the exact same issue with the NOT ALLOW problem. And people, we do read some times (the newbies) and nowhere but here you say that AFTER HSPL YOU MUST NOT UGPRADE FROM MEMORY CARD!!!! And NO it is not included inhere: http://forum.xda-developers.com/showthread.php?t=609477
Cheers,
and thanks to all the smart people inhere!
D
Click to expand...
Click to collapse
With hspl installed you CAN flash CUSTOM roms using sd card, it is only flashing OFFICIAL roms through sd card that removes hspl.
sorry to crash this thread but...
i have flashed HSPL on to my HD2 and am now wanting to install HTC's new 1.66 rom.
i have a VF hd2 so i am a little worried i will hit the same issues as the OP did.
can some one hold my hand through flashing the ROM as im a complete noob to this.. i have read the FAQs and im a bit like with all the acronyms etc
adam_r said:
sorry to crash this thread but...
i have flashed HSPL on to my HD2 and am now wanting to install HTC's new 1.66 rom.
i have a VF hd2 so i am a little worried i will hit the same issues as the OP did.
can some one hold my hand through flashing the ROM as im a complete noob to this.. i have read the FAQs and im a bit like with all the acronyms etc
Click to expand...
Click to collapse
Use the custom ruu to flash it. Do not put the nbh on the sd. I quote from the "[HSPL]How to flash everything" thread:
4) Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Click to expand...
Click to collapse
Why people cant read? refering to the person who started this thread.
No Problem Flashhing to 1.66 on a Voda HD2 with HSPL
I have a voda HD2 and being a total Newbie to the HTC / WM .. I followed the Dummie guide.. (thanx to all, for that.. fantastic..) installed HSPL..and then installed the latest 1.66 from the HTC site using a boggus serial number.. As actual would not let me download it. No problemo..
Feeling a bit more adventureous.. any suggestions for the best 'cooked Rom' ??
From my understanding, you can flash away Stock ROMS using activesync. No need for HSPL.
I won't bother with the exact history of things but I'll tell you what's on the phone and what I can't get to work.
SPL-2.00. 10000 XE
Radio 2.06.50.04
ROM Leo lite 2.6 WE (21892.5.0.89)
Current ROM works until I try to do anything involving phone radio and then it just locks up. My radio is not up to date for this ROM I assume.
Trying to flash anything at all via LEOIMG microsd card does nothing but sit at the Loading.... screen with never any progress. (I have also tried this with a goldcard that somebody made me and I get the same error.) Have used both a 16gb card and a 2gb card, all formatted to fat32
I am unable to flash a new ROM or new Radio or get the SPL to allow any OEM ROM/SPL package to install via SDcard.
Trying to flash anything with the standard flasher tool and it never did anything but time out. SSPL used to work but now it does nothing but time out. I'm stuck on this ROM, can't change it and phone doesn't work.
What I would like to do is get HSPL back on it, the most current radio and the latest US T-Mobile ROM
If you can help me do this I will pay $25 for the person to help me get it off my phone. There is a chance my goldcard could have been made incorrectly, I don't know anything about them. I can pay you via PayPal or mail you a check, whatever works for you. All I can do is give you my word that I will keep my end of the deal. I'm a 44 year old family man and a department manager of a casino. I would really appreciate any help.
If I posted this in the wrong place please move it but I'm at wits end and just want my phone back to normal.
Edit: Just to be clear, the $25 reward is for getting the SPL 2.0 off of my phone and/or getting me upgraded to the latest radio so I can run the most current TmoUSA ROM properly.
the problem appears to be that you have slightly different hardware to every one else.
didnt realise you were having issues with sspl, that at least should work ok. by time out do you mean there sspl boot screen appears burt nothing else?
if so what happens if you disconnect the usb cable and plug it back in?
if it changes to usb then rerun the sspl without changing anything on the hd2
you could also try - and uninstall the windows drivers for the qualcomm cdma drivers or whatever they are called on you pc. and reconnect in boot loader to let them reinstall.
SSPL used to work, it stopped working after I flashed a newer rom to play with. When I use the SSPL it goes into the bootloader screen just fine, then I hear the USB disconnect sound and the SSPL program times out quickly with the exit button citing no connection.
I have 2 x Windows 7 64 bit computers, 1 x Windows 7 32 bit and one XP 32 bit computer. I get the same results on any of them. All after the most recent ROM upgrade.
I have not tried running SSPL from boot loader screen, did not know that was possible. Trying that now. Just need to download a known working ROM.
If that works I'll be back in the same boat as before, stuck with 2.0 SPL and 2.06 radio. I want that SPL 2.0 off my phone badly.
OK, trying SSPL from the bootloader screen got me a little further towards ROM flashing. I can see the htc on the black screen with the progress bar. It now sits at 0% with no movement indefinitely.
Going to try another ROM and see if I can get the ROM installation to actually begin.
If you still haven't tried it do this: start SSPL when you hear the USB disconnect sound remove the USB cable (either from device or PC) and then connect it again! this should allow the SSPL to enter USB mode! I've had similar problems long ago and this trick was doing the job! Not sure that it will help you but just a thought!
Newb here:
I had something similar. I installed HSPL and everything was fine thereafter. The radio wouldn't flash any other way, in fact it would disconnect like you said, or if I manualy took the phone to boot loader, it would stick at 0%.
There is a HSPL thread stickied in the ROM section and I believe it explains how to remove it if you need to "re" validate your warranty. Although reading once more it does say you need SPL 1.42 to get it to install.
Have you tried installing an official HTC ROM downlaoded from their site? This will take you back to the original SPL version 1.42...
I don't have HSPL on my phone, I have SPL 2.0 Nothing is out currently to remove a later SPL with the exception of flashing an OEM full package ROM through the sd card but that doesn't work for me.
I have tried multiple roms now using SSPL from the bootloader screen and none will move the progress bar past 0%
Still stuck. : - (
Have you tried to hard spl it? If I missed it in your post, I apologize.
Not in a long while, I should try again I guess but I was totally under the impression that HSPL will error all the time unless you have SPL 1.42 installed on the phone.
Edit: Just tried and it errors because SPL 1.42 is not on the phone, it's the only SPL that HSPL works on as far as I know.
balane have you tried installing a stock rom from your SD card? this would revert the spl back to 1.42 and allow you to then flash HSPL (I think, almost certain) but you said you cant do anything with the sd card, have you tried that? have you tried with different SD cards? also have you made sure that it is formatted to FAT32?
Another thing you could try if all else fails: MTTY, look at the MTTY thread by MystikGenius, its stickied in the rom development section, this will format your phone from which you can then try to flash from usb or sd. I would recomend trying to flash from SD which then again may revert your spl.
Im going to school now so I wont be able to help you anymore 8 or so hours, but PM me later if your still stuck.
I may be wrong but from what I read in the threads I thought it was not possible to go back to anything under 2.0 once you flash a 2.0 SPL. You can't flash back to 1.48 or 1.66. You might be able to flash the new TMOUS which is in the 2.0 SPL range.
Yes, I've tried dozens of stock roms from the sdcard, every one I could find in fact and they all hang at the Loading... screen. As stated in the op, I used two different cards both formatted to fat32. I guess I could try a third card, not sure if it's worth a try or not.
I looked at MTTY but that doesn't do a thing with SPL and my SPL is the root of my issues.
Update: I finally did find a ROM I could get flashed via SSPL. It took like 3 tries to get the progress bar going but it did get installed. I can't even recall what series of events got it to go but at least my phone turns on and works.
Still the same SPL and radio though. No change there.
bobsbbq said:
I may be wrong but from what I read in the threads I thought it was not possible to go back to anything under 2.0 once you flash a 2.0 SPL. You can't flash back to 1.48 or 1.66. You might be able to flash the new TMOUS which is in the 2.0 SPL range.
Click to expand...
Click to collapse
I could have swore I read some people who were able to get the SPL 2.0 off their phones but I could be mistaken. I'm actually ok with any SPL as long as I can sspl different ROMs. I just want to get the radio current so I can run the latest TmoUS ROM, I would totally and 100% pleased with being able to update the radio. I have found now way to flash a more current radio.
balane said:
I won't bother with the exact history of things but I'll tell you what's on the phone and what I can't get to work.
SPL-2.00. 10000 XE
Radio 2.06.50.04
ROM Leo lite 2.6 WE (21892.5.0.89)
Current ROM works until I try to do anything involving phone radio and then it just locks up. My radio is not up to date for this ROM I assume.
Trying to flash anything at all via LEOIMG microsd card does nothing but sit at the Loading.... screen with never any progress. (I have also tried this with a goldcard that somebody made me and I get the same error.) Have used both a 16gb card and a 2gb card, all formatted to fat32
I am unable to flash a new ROM or new Radio or get the SPL to allow any OEM ROM/SPL package to install via SDcard.
Trying to flash anything with the standard flasher tool and it never did anything but time out. SSPL used to work but now it does nothing but time out. I'm stuck on this ROM, can't change it and phone doesn't work.
What I would like to do is get HSPL back on it, the most current radio and the latest US T-Mobile ROM
If you can help me do this I will pay $25 for the person to help me get it off my phone. There is a chance my goldcard could have been made incorrectly, I don't know anything about them. I can pay you via PayPal or mail you a check, whatever works for you. All I can do is give you my word that I will keep my end of the deal. I'm a 44 year old family man and a department manager of a casino. I would really appreciate any help.
If I posted this in the wrong place please move it but I'm at wits end and just want my phone back to normal.
Edit: Just to be clear, the $25 reward is for getting the SPL 2.0 off of my phone and/or getting me upgraded to the latest radio so I can run the most current TmoUSA ROM properly.
Click to expand...
Click to collapse
My English is not good. But I can help you. You can refer here ( in post 18&19) and use google to translate language :
http://www.pdaviet.net/showthread.p...KHI-UP-ROM-TMOUS-BẢN-TEST-(2-07)-BẰNG-THẺ-NHỚ
I have successfully repaired (with any Goldcard ) HD2 damaged when the flash rom TMOUS with memory card . And now can flash with any rom that is the base rom from 2:07 or higher (with SSPL)
Sorry for my bad English
balane said:
I don't have HSPL on my phone, I have SPL 2.0 Nothing is out currently to remove a later SPL with the exception of flashing an OEM full package ROM through the sd card but that doesn't work for me.
I have tried multiple roms now using SSPL from the bootloader screen and none will move the progress bar past 0%
Still stuck. : - (
Click to expand...
Click to collapse
No it won't be SSPL as we know it, the HTC stock ROM you can download from their site (Google "HTC HD2 DOWNLOAD") will use it's own method of getting onto your device and will reload SPL 1.42 for you. Although apparently you may not be able to do this with SPL 2. You say you have done it with a gold card, have you tried the stock rom downloaded from HTC via USB?
Otherwise, pester bepe for when the HSPL comes out that is compatible ywith SPL 2!
ancola66 said:
My English is not good. But I can help you. You can refer here ( in post 18&19) and use google to translate language :
http://www.pdaviet.net/showthread.p...KHI-UP-ROM-TMOUS-BẢN-TEST-(2-07)-BẰNG-THẺ-NHỚ
I have successfully repaired (with any Goldcard ) HD2 damaged when the flash rom TMOUS with memory card . And now can flash with any rom that is the base rom from 2:07 or higher (with SSPL)
Sorry for my bad English
Click to expand...
Click to collapse
Will not allow me to even read the forum because I'm not a member, can you copy paste the pertinent information here please?
You can use ANY goldcard???
mwillems2 said:
No it won't be SSPL as we know it, the HTC stock ROM you can download from their site (Google "HTC HD2 DOWNLOAD") will use it's own method of getting onto your device and will reload SPL 1.42 for you. Although apparently you may not be able to do this with SPL 2. You say you have done it with a gold card, have you tried the stock rom downloaded from HTC via USB?
Click to expand...
Click to collapse
I've tried multiple OEM HTC Roms and all give the same stuck at Loading... screen. Is there a specific HTC oem ROM you can recommend I try?
balane said:
Will not allow me to even read the forum because I'm not a member, can you copy paste the pertinent information here please?
You can use ANY goldcard???
Click to expand...
Click to collapse
YES ! You can use any Goldcard. I write instructions for you but my very bad English
balane said:
I've tried multiple OEM HTC Roms and all give the same stuck at Loading... screen. Is there a specific HTC oem ROM you can recommend I try?
Click to expand...
Click to collapse
When you say oem, do you mean just the nbh with which you have tried to install using tools or the self extracting exe that HTC provide? I'm just asking cos to me, oem means it comes without all the manufacturers extras.
I've always been under the impression that the only way to downgrade an SPL was to install a complete OEM package ROM/Splash/Radio/SPL as a LEOIMG.nbh from the root of the SD card. I've tried dozens of these both from US based ROMs and abroad. None of gone past the Loading.... screen. I've tried 1.42 and above ROMs, no luck with any.
Hey so i just picked up an hd2 on craigslist. when the seller handed my the phone he showed me the phone working and then did a hard reset so i thought nothing of it and took the phone while it was resetting. then while waiting for it to boot i noticed it was taking quite a while so i took out the battery and let it reboot, it turned on then froze on the homescreen. i've tried several hard resets and have gotten the phone to the point where it works but only after putting in a removing the battery several times and the phone sticking on the "stick together" logo. I was going to try to do the newest tmobile update on the phone using the one available on their website but now i have an issue plugging the phone into the computer or wall adapter as it will make the phone freeze and ill have to go back through my removing the battery 5 times process. is this some sort of common issue with a common fix or should i take the phone to tmobile or htc and see what they can do for me. i dont have a receipt as a purchased the phone on craigslist so im not sure tmobile will do anything for me.
Edit: i can now connect my phone to the pc i'm trying to update to 2.13.531.1 but i got to 8% but the update froze there and the phone currently has no image version. I'm using windows 7 ultimate and ive tried to run as administrator and with xp service pack 3 compatibility.
thatg said:
Hey so i just picked up an hd2 on craigslist. when the seller handed my the phone he showed me the phone working and then did a hard reset so i thought nothing of it and took the phone while it was resetting. then while waiting for it to boot i noticed it was taking quite a while so i took out the battery and let it reboot, it turned on then froze on the homescreen. i've tried several hard resets and have gotten the phone to the point where it works but only after putting in a removing the battery several times and the phone sticking on the "stick together" logo. I was going to try to do the newest tmobile update on the phone using the one available on their website but now i have an issue plugging the phone into the computer or wall adapter as it will make the phone freeze and ill have to go back through my removing the battery 5 times process. is this some sort of common issue with a common fix or should i take the phone to tmobile or htc and see what they can do for me. i dont have a receipt as a purchased the phone on craigslist so im not sure tmobile will do anything for me.
Click to expand...
Click to collapse
I would put the phone in boot load manually by holding the volume down button while turning it on, and remove the memory card and then reflash the tmobile rom
can someone also help me figure out how to get the ruu.nbh file off this rom and how big it should be so i can try to flash it from the sd card. thanks
http://forum.xda-developers.com/showthread.php?t=681030
zelendel said:
I would put the phone in boot load manually by holding the volume down button while turning it on, and remove the memory card and then reflash the tmobile rom
Click to expand...
Click to collapse
i found a .nbh file on my computer that was 4mb and renamed it leoimg.nbh then tried putting it on a freshly formatted fat 32 micro sd car and went into bootloader mode but the phone gives me an upgrade error, asks me to try again and just goes to a white "loading..." screen now the phone is stuck here. its like the newest issue is the one im stuck with. now i cant get the phone to sync with the computer or run the .exe to recognize the phone
thatg said:
i found a .nbh file on my computer that was 4mb and renamed it leoimg.nbh then tried putting it on a freshly formatted fat 32 micro sd car and went into bootloader mode but the phone gives me an upgrade error, asks me to try again and just goes to a white "loading..." screen now the phone is stuck here. its like the newest issue is the one im stuck with. now i cant get the phone to sync with the computer or run the .exe to recognize the phone
Click to expand...
Click to collapse
What error did it give you? Found an nbh file? was it from a stock rom? Do you have Hard SPL on it? If it doesnt have HSPL on it then you will only be able to load a stock rom
zelendel said:
I would put the phone in boot load manually by holding the volume down button while turning it on, and remove the memory card and then reflash the tmobile rom
Click to expand...
Click to collapse
+1 or flash the phone then task 29 it.
Sent from my HTC Desire using XDA App
zelendel said:
What error did it give you? Found an nbh file? was it from a stock rom? Do you have Hard SPL on it? If it doesnt have HSPL on it then you will only be able to load a stock rom
Click to expand...
Click to collapse
no i have not run hard spl so i can only install a stock rom a suppose. the exe gets stuck at 8%, i have no idea where the right nbh file is. i read somewhere when you run the exe it installs the nbh in a temp folder but im not sure i found the right one. ive also downloaded task29 and tried to run as admin but it doesnt do anything just goes to the htc install screen and stays at 0% Getting frustrating it was working fine actually before i tried to install the new tmobile software update. ive read that task29 gets rid of extra leftovers of other roms and might help the exe finish up on the phone and get past that 8% wall but it doesnt seem to be working for me
right click the stock exe file choose extract here, will give 9 or so files, one of them is about 200meg and is called ruu_signed.nbh that's the file you want.
randomly flashing nbh files that you don't know what they are, that's about the stupidest thing you can do...... you deserve a brick for being an idiot.
samsamuel said:
right click the stock exe file choose extract here, will give 9 or so files, one of them is about 200meg and is called ruu_signed.nbh that's the file you want.
randomly flashing nbh files that you don't know what they are, that's about the stupidest thing you can do...... you deserve a brick for being an idiot.
Click to expand...
Click to collapse
lol thank you for the words of encouragement, so i've extracted the .nbh file its 268mb, renamed it to leoimg.nbh tried the update from the sd card and it fails at the radio says, update terminated, update FAIL. any idea where to go from here?
Edit: i've run hspl3 on the phone is boot loader mode and have also run task29 from doloop but still get the same error with the tmobile file. 8% using the exe and FAIL trying to flash from the sd card
heh you're welcome. (i was harsh to make the point,,, if you found a random bottle of liquid that said petrol on it, you wouldn't put it in your car till you were sure it was petrol, right?)
as to why it failed, i'm not sure, i think i'd probably hspl3, choose 2.08.hspl, then try flash a radio on its own (see the tmous radio thread) because it could be a bad radio.
just please confirm the exact filename of the .exe you extracted ruu_signed from?
samsamuel said:
heh you're welcome. (i was harsh to make the point,,, if you found a random bottle of liquid that said petrol on it, you wouldn't put it in your car till you were sure it was petrol, right?)
as to why it failed, i'm not sure, i think i'd probably hspl3, choose 2.08.hspl, then try flash a radio on its own (see the tmous radio thread) because it could be a bad radio.
just please confirm the exact filename of the .exe you extracted ruu_signed from?
Click to expand...
Click to collapse
The first exe file, which got to 8 percent then went red and failed was
T-Mobile_HD2_MR_Software_2.13.531.1
After hspl3 and using task29 i tried flashing this exe which gets to 99% and fails
RUU_Leo_1_5_TMOUS_2.02.531.MASD_S__Radio_Signed_15.29.50.07U_2.06.50.04_TeleNav-5.5.42
that second one, did you flash from sd card? cos its a manufacturing test rom, and if so then you may now be stuck with a test spl of 2.02, and if so things just got a heap worse,,,
go into bootloader and tell me what it says next to spl
samsamuel said:
that second one, did you flash from sd card? cos its a manufacturing test rom, and if so then you may now be stuck with a test spl of 2.02, and if so things just got a heap worse,,,
go into bootloader and tell me what it says next to spl
Click to expand...
Click to collapse
i tried flashing using the .exe method in bootloader mode. next to spl it reads -2.08.hspl 8g XE
it now says
Upgrade ROM code error
ah ok, good.
so, it seems to be the radio causing the error, so since you have hspl installed, why not try a custom rom? they don't include a radio, so it may bypass the problem.
samsamuel said:
ah ok, good.
so, it seems to be the radio causing the error, so since you have hspl installed, why not try a custom rom? they don't include a radio, so it may bypass the problem.
Click to expand...
Click to collapse
Which do you suggest, i bought the phone so that i could ultimately install android on it. but it seems i'd be lucky to even have wm running on the thing
Edit. just tried kumars classic rom, renamed to leoimg tried running off the sd card, The update finishes successfully but after i hit the reset button on the back of the phone i just see the tmobile stick together logo and the phone doesnt boot. Do a lot of people struggle with the hd2s or do i just have a bad example here?
well unfortunately i think you may have a dud. its the radio that is preventing it from booting.
it could be the radio from that test rom, it could be something else (but still the radio)
options...
its still under warranty, speak to t mobile and/or htc, but don't mention flashing and be sure to remove hspl if you do send it back. (run hspl3, choose 2.08.0000, that's stock)
or
look on here for a user called xmoo, he knows a lot about this sort of problem, (im just good with regular flashing issues)
im having the same issue so if you believe its the radio will installing different radio maybe fix the problem?
i;ve tried installing a new radio from the sd card. it goes red and fails
It sounds like a hardware issue at this point. I'm willing to bet you fried something when you pulled the battery in the middle of the master reset.
Hope thats something htc will cover. Phones on its way over
Having a problem with a friends TMOUS HD2.
It was Borked when trying to install Android (Nand) and he gave it to me to try and fix.
Managed to get rid of MAGLDR by Task 29ing and flashing an 'EnergyROM' BUT.... it seems there is NO radio on the phone.
Trying to install the official TMOUS upgrade via the SD Card method fails at the radio stage with the error:
'00018003
LEOIMG.nbh - Fail
RADIO_V2 - RSA Fail'
Trying to install the official ROM via USB instead of SD Card, it always fails at 8%.
trying to install any radio via USB fails at 96%....
This has me confused as all hell.... any ideas??
Andy
What SPL or HSPL is on the HD2? This could be your problem.
Lots of similar threads if you look around carefully,, "stuck radio" its commonly called.
There are very very few successful ones, tho,I'm sorry to say. One or two along the lines of using certain test roms in a certain order, and such.
Good look, keep hopeful, but prepare for dissapointment.
have you tried flashing a radio via SD card?
also, have you tried uninstalling HSPL THEN stock ROM via official site?
orangekid said:
have you tried flashing a radio via SD card?
also, have you tried uninstalling HSPL THEN stock ROM via official site?
Click to expand...
Click to collapse
Done both of those. Still fails when installing the radio,
If I do the radio ONLY, it fails at 98% wether its via USB or via SD Card. If I install the full official ROM, it fails at 8%, which is where its installing the radio.....
Been using HSPL 2.08 and SPL 2.08 ....
Andy
Boradan said:
Done both of those. Still fails when installing the radio,
If I do the radio ONLY, it fails at 98% wether its via USB or via SD Card. If I install the full official ROM, it fails at 8%, which is where its installing the radio.....
Been using HSPL 2.08 and SPL 2.08 ....
Andy
Click to expand...
Click to collapse
just for grins can you run HSPL4 and flash SPL 3.03 then try flashing a 3.04 ROM?
edit:
you might also try this:
1) flash task29
2) flash 2.15.00 via RUU,
this might work if for some reason some remnants of the ROM is somehow preventing your HD2 correctly communicating during radio flash.
orangekid said:
just for grins can you run HSPL4 and flash SPL 3.03 then try flashing a 3.04 ROM?
edit:
you might also try this:
1) flash task29
2) flash 2.15.00 via RUU,
this might work if for some reason some remnants of the ROM is somehow preventing your HD2 correctly communicating during radio flash.
Click to expand...
Click to collapse
Hey cerrect me if I am wrong but the OP can use the .nbh file of th e 2.15.00 radio to run the Task 29 on the HD2 but also flash the radio to the HD2. I mean Task 29 just needs a .nbh file to work.
Go check out post #2 and #6 of the [REF] Task 29 (format) without drivers, without mtty. thread.
you're right, it's the NBH file that makes the difference.
ok, well its definitely a radio problem.
I got the latest tmous upgrade rom from their site ( Using the Serial number to ensure it was the right ROM.)
T-Mobile_HD2_MR_Software_3.14.531.1
When I try to install it, it fails at 8%.
I purchased PSAS and used it to strip all the files out of the NBH, then I rebuilt it WITHOUT the radio.
The ROM installs fine now BUT.....
If I try to install the radio only, I get an error at 96%
So the phone is FINE to install a ROM on, but CANT install a Radio.... AT ALL.
Used HSPL 3.03 and 2.08, Also tried 3.03.0000 and 2.08.0000.
Did the task29 with the radio.... failed at the same point.
Tried making a goldcard with PSAS, but when I do that, it gets stuck on 'loading' when trying to flash the radio from SD Card (Tried 2 SD cards, both 2GB and the same thing happened.)
Contacted HTC Europe and they wont take the phone as its a US version
Dont suppose anyone has JTAG hardware and wouldnt mind trying to fix this as it seems it is my only option now
Andy
Boradan said:
ok, well its definitely a radio problem.
I got the latest tmous upgrade rom from their site ( Using the Serial number to ensure it was the right ROM.)
T-Mobile_HD2_MR_Software_3.14.531.1
When I try to install it, it fails at 8%.
I purchased PSAS and used it to strip all the files out of the NBH, then I rebuilt it WITHOUT the radio.
The ROM installs fine now BUT.....
If I try to install the radio only, I get an error at 96%
So the phone is FINE to install a ROM on, but CANT install a Radio.... AT ALL.
Used HSPL 3.03 and 2.08, Also tried 3.03.0000 and 2.08.0000.
Did the task29 with the radio.... failed at the same point.
Tried making a goldcard with PSAS, but when I do that, it gets stuck on 'loading' when trying to flash the radio from SD Card (Tried 2 SD cards, both 2GB and the same thing happened.)
Contacted HTC Europe and they wont take the phone as its a US version
Dont suppose anyone has JTAG hardware and wouldnt mind trying to fix this as it seems it is my only option now
Andy
Click to expand...
Click to collapse
DUDE I GOT EXACTLY THE SAME PROBLEM AS YOU....
And its not even my HD2
So you got any solution yet?
pleasee
FIXED
Got it sorted out now
How I did it:
PURE LUCK
Installed HSPL 2.08 on the phone
Downloaded T-Mobile_HD2_MR_Software_3.14.531.1 from the tmobile website.
used PSAS to split the nbh into its components, then rebuilt it WITHOUT the radio.
booted the phone into bootloader and installed the ROM via USB ( without radio)
Formatted a 2gb SD card in windows.... FAT32 4096kb cluster size
Radio 2.15.40.14 renamed to LEOIMG.nbh and put at the root of the SD card.
Popped it in the phone and booted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
................................................. ad nauseum....
must have done it about 50 times and then it suddenly WORKED......
Now have a working phone
Boradan said:
Got it sorted out now
How I did it:
PURE LUCK
Installed HSPL 2.08 on the phone
Downloaded T-Mobile_HD2_MR_Software_3.14.531.1 from the tmobile website.
used PSAS to split the nbh into its components, then rebuilt it WITHOUT the radio.
booted the phone into bootloader and installed the ROM via USB ( without radio)
Formatted a 2gb SD card in windows.... FAT32 4096kb cluster size
Radio 2.15.40.14 renamed to LEOIMG.nbh and put at the root of the SD card.
Popped it in the phone and booted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
Rebooted. Started loading the nbh. Failed at 96%.
................................................. ad nauseum....
must have done it about 50 times and then it suddenly WORKED......
Now have a working phone
Click to expand...
Click to collapse
heey man can i please please get your PSAS
im pretty much screwed and my mom wouldnt get to pay the software.. please help me get my phone back again
Boradan said:
................................................. ad nauseum....
Click to expand...
Click to collapse
and what does that mean ghehe.
i want the phone back to get it back to the guy!! otherwise i need to pay a NEW HD2 for him and i cant...
EDIT: can you PM me the program or your msn maybe ? :$
you dont need the program..... Just install HSPL on your phone, Flash a ROM that has no radio (a custom ROM such as the EnergyROM would do fine) using USB/bootloader method then get the radio you need onto a freshly formatted (FAT32 with 4096kb cluster size) SD card LESS than 4GB in size. Rename the radio 'LEOIMG.nbh' and then just KEEP TRYING. Perserverance is the name of the game here.
I made over 50 attempts before one went through.
Oh.... gettting the ROM (with no Radio) onto the phone took a few attempts aswell. Think it was 3 or 4, but I kept going because the install was failing at different places each time)
Andy
Boradan said:
you dont need the program..... Just install HSPL on your phone, Flash a ROM that has no radio (a custom ROM such as the EnergyROM would do fine) using USB/bootloader method then get the radio you need onto a freshly formatted (FAT32 with 4096kb cluster size) SD card LESS than 4GB in size. Rename the radio 'LEOIMG.nbh' and then just KEEP TRYING. Perserverance is the name of the game here.
I made over 50 attempts before one went through.
Oh.... gettting the ROM (with no Radio) onto the phone took a few attempts aswell. Think it was 3 or 4, but I kept going because the install was failing at different places each time)
Andy
Click to expand...
Click to collapse
WOW, so you just did try to isntall the radio via the SD card and tried like 50 times and then BENG it worked???
nickislauw said:
WOW, so you just did try to isntall the radio via the SD card and tried like 50 times and then BENG it worked???
Click to expand...
Click to collapse
Yup. Wasted €30 on PSAS
Dont even need a Goldcard generated with HSPL 4 out now........
Boradan said:
Yup. Wasted €30 on PSAS
Dont even need a Goldcard generated with HSPL 4 out now........
Click to expand...
Click to collapse
hmm..
so in short.
I just put 2.08 HSPL on it, then install a CUSTOM rom.. after that, i get back to the bootloader and insert the goldcard with the freshly new 2.15 radio and when it gives a RSA failed error i just try like 50 times???
Thanks.
Worked for me. Dont even need a goldcard as they dont work with HSPL installed in the phone... only with stock SPLs
Andy
Boradan said:
Worked for me. Dont even need a goldcard as they dont work with HSPL installed in the phone... only with stock SPLs
Andy
Click to expand...
Click to collapse
ok man im gonna try it immediatly when i get home!
BTW, you have a tmobile HD2, ive got a normal.. so i hope it wont make difference
EDIT: i will post the result when it gets done or failed..
Good luck with it....
Now I have to decide wether or not to install Android again on this phone..... Sorta reluctant after these shenannigans
Meh.... fixed it once, can do it again I suppose
wish me luck
Andy