[Q] factory reset no "android recovery" - Xoom General

When attempting to factory reset, the instructions say that the messeage "android recovery" will appear in the top left if booted when power + volume down. This only sends me to the fastboot message, and it will not change to "android recovery". Anyone else have this problem

I got in by pressing up while it's powering up
Edit: correction ... that gets u into rsd2 mode
Sent from my Xoom using XDA App

As far as I remember, it's just Vol(-) while on the "Dual Core" screen while powering up to scroll through boot options. Once you find the one you want, recovery, Vol(+) will bring you into it.

Related

Defy plus stuck at home screen

Dear gentleman,
Pls help to save my Defyplus!!!
I get a problem after install app "Slide to unnlock.apk" --> stuck at lock screen, and can not do anything, I try to do Factory Reset but can not go to Settings page
*My Defyplus rooted, but not yet install Boot menu.
Many tks for your kindly support urgently!
What is this app you have installed? Is it from the market? From the forums? What does it do? Is it an app for rooted phones only?
You can try to start your phone in SAFE MODE. When phone starts, hold down volume up button + volume down button until you see the lock screen. It should say SAFE MODE in left corner. Uninstall the app and reboot.
To do a factory reset you do not need to go to settings. When starting your phone, hold down the volume down key BEFORE you turn it on, and keep it pressed. When warning triangle appears, press both volume keys to enter recovery. use volume keys to navigate and select options with power button. Chose "wipe data/factory reset" and reboot.
Read the defy beginner's guide as well.
Sent from my Defy+ using xda premium (app needs update!)
Many thanks Fiskenigaten,
I collected the app from a forum!
Following your instruction --> Hard reset successed!
Best wish to you all time!

Nexus 4 stock Recovery NO COMMAND issue

hello there..i bought my nexus 4 yesterday..its AWESOME!!..so i wanted to start flashing some custom roms etc..so i wanted to boot into stock recovery and see how the new one looks like..when i tried booting into it..i get a RED triangle with the android sleeping..can someone help me..wuold be highly appreciated..and thanks in advance..
sumeetp said:
hello there..i bought my nexus 4 yesterday..its AWESOME!!..so i wanted to start flashing some custom roms etc..so i wanted to boot into stock recovery and see how the new one looks like..when i tried booting into it..i get a RED triangle with the android sleeping..can someone help me..wuold be highly appreciated..and thanks in advance..
Click to expand...
Click to collapse
I'm new to nexus family too and had a lot of problems with it. (Never have problems but this recovery cost me a lot of time).
The solution is:
When you are EXACTLY at the red exclamation mark screen.
1) Press and hold POWER
2) Press volume UP.
That should show the options in less than 2 seconds.
Sent from my Nexus 4 using Tapatalk 2
thesebastian said:
I'm new to nexus family too and had a lot of problems with it. (Never have problems but this recovery cost me a lot of time).
The solution is:
When you are EXACTLY at the red exclamation mark screen.
1) Press and hold POWER
2) Press volume UP.
That should show the options in less than 2 seconds.
Sent from my Nexus 4 using Tapatalk 2
Click to expand...
Click to collapse
thanx mate..worked like a charm
I am experiencing the same "no command" issue, already tried the volume up + power and nothing happens, if I flash CWM touch 6.0.3.1 everything works but I can't go back to stock recovery no matter what, any advise?
Already flashed stock recovery using Wugfresh's Nexus Root toolkit but the "no command" problem persists.
Thank you.
lsv-1 said:
I am experiencing the same "no command" issue, already tried the volume up + power and nothing happens, if I flash CWM touch 6.0.3.1 everything works but I can't go back to stock recovery no matter what, any advise?
Already flashed stock recovery using Wugfresh's Nexus Root toolkit but the "no command" problem persists.
Thank you.
Click to expand...
Click to collapse
it's power then volume up. you're doing it the wrong way. you need to press power first and while pressing on that you press volume up
thephantom said:
it's power then volume up. you're doing it the wrong way. you need to press power first and while pressing on that you press volume up
Click to expand...
Click to collapse
Yeap, same thing, I press and hold the power and then I press the volume up, nothing happens. I even formatted the phone completely using the 4.2.2 image from google, nothing, the no command error keeps coming up, the only way to have a recovery is flashing CWM touch.
---------- Post added at 10:37 AM ---------- Previous post was at 09:44 AM ----------
I've got my N4 maybe a month ago, I installed the 4.2.2 OTA as soon as I got it, the I proceeded to unlock it and root it, one day someone recommended to clear the cache of the phone using the stock recovery (which I thought I had / to fix another problem that I was having) I went to fastboot and tried to access recovery, BOOM, just an android laying down with a red exclamation mark, no "no command" error at all. I downloaded CWM touch and flashed it using Nexus Root Toolkit, that worked fine, but I didn't want a custom recovery and also I needed to fix a 3G latency problem that I was having, after some reading I saw that someone recommended a full flash using the stock google image.
A couple of days I proceeded to flash the factory image, I installed it, after that I did a factory reset from android itself. After doing all that I wanted to clear the cache with the stock recovery just in case, BOOM, an an android laying down with a red exclamation mark and this time with a "no command" error. Tried the trick of holding the power and pressing the volume up, NOTHING HAPPENS!
Right now I am using CWM Touch.
Any suggestion?
Thank you.
No real solution??? Sad...
---------- Post added at 02:13 PM ---------- Previous post was at 02:09 PM ----------
thephantom said:
it's power then volume up. you're doing it the wrong way. you need to press power first and while pressing on that you press volume up
Click to expand...
Click to collapse
Nothing, this answer is unhelpful
I have this issue as well. I tried to "unroot" my N4 (and Im a noob at this), and I think I did something wrong because when I access recovery mode from the bootloader I see the "dead android" but no matter what I do I dont see the control/menu. I tried:
- holding all buttons at the same time
- holding the power button and the down button (in sequence)
- holding the power button and the up button (in sequence)
So now I can not boot my Nexus, I can not wipe my Nexus and I can not access it from the PC. I was running 4.3 and I used the "How to Unroot Nexus 4 to Stock 4.2 Jelly Bean on Windows!" youtube guide ( I am not allowed to post links) to unroot my device (nexus 4), where I fail at 8:45, I simply dont see that menu popping up. Instead, my Nexus shuts down or reboots.
Please help
Is there no fix for this?
I decided to go back to stock to get 4.3. I flashed 4.2.2 using the Nexus toolkit and then got 4.3 via an OTA after this I rooted my phone. As the OTA worked I would imagine that the stock recovery was working. When I tried to install the latest OTA I got the no command issue. I can flash cwm recovery no problem. But when I try to flash stock recovery either via a toolkit or via fastboot command it does not work - no command. And holding in power and then volume up doe nothing. Any advice? I suppoe I cando a full wipe flash the stock 4.3 image and see if this helps. Has anyone had any success fixing this problem?
I have the same issue.
Even when trying to get to stock recovery through Nexus Root Toolkit gets me a NO COMMAND screen.
It seems like the recovery is not there.
Still looking for an answer - any help?
finbaar said:
Is there no fix for this?
I decided to go back to stock to get 4.3. I flashed 4.2.2 using the Nexus toolkit and then got 4.3 via an OTA after this I rooted my phone. As the OTA worked I would imagine that the stock recovery was working. When I tried to install the latest OTA I got the no command issue. I can flash cwm recovery no problem. But when I try to flash stock recovery either via a toolkit or via fastboot command it does not work - no command. And holding in power and then volume up doe nothing. Any advice? I suppoe I cando a full wipe flash the stock 4.3 image and see if this helps. Has anyone had any success fixing this problem?
Click to expand...
Click to collapse
When you get the no command prompt do the following.
Press and hold the power button followed by pressing and holding the volume up button. Release only the volume up button after 2 seconds and you will be in recovery.
Sent from my Nexus 4 using XDA Premium 4 mobile app
See this
http://forum.xda-developers.com/showpost.php?p=44388152&postcount=13
jangietka said:
I have the same issue.
Even when trying to get to stock recovery through Nexus Root Toolkit gets me a NO COMMAND screen.
It seems like the recovery is not there.
Still looking for an answer - any help?
Click to expand...
Click to collapse
Seems that you have the stock recovery installed (that Android laying on its back with a red triangle is the stock recovery).
If I'm not missunderstanding your issue, it shouldn't really be an issue but it's just like how it should be.
Getting No Command while entering Recovery Mode in my Nexus 4
Hi All,
I am also facing the same problem, I got kitkat update, the update (239 MB) downloaded but while installing, it shows No Command with Red Triangle. My Device is rooted.
Please help me..
Regards,
Ajay
got the same problem
i had the no command problem and then i watched videos how to get recovery mod
i installed teamwin recovery mod and i had NO root for android 4.4.3
at nexus 4 toolkit thare is still no version of 4.4.3
how do i fix it?
how do i root it without flashing image?
thanks
~oren
finbaar said:
When you get the no command prompt do the following.
Press and hold the power button followed by pressing and holding the volume up button. Release only the volume up button after 2 seconds and you will be in recovery.
Sent from my Nexus 4 using XDA Premium 4 mobile app
See this
http://forum.xda-developers.com/showpost.php?p=44388152&postcount=13
Click to expand...
Click to collapse
This worked! Thanks!
The trick is release only volume up button.
Yes, but the OTA update still does not install with this method.
"No Command" issue solved for Zuum 9330
I want to thank every one of you guys. I had same issue with my phablet. By reading your comments I got ideas to try some key combinations, and factory reset my phone. Here is what I did:
1) Power down the phone
2) Press and hold "volume up", then Press and hold "power" button until Android logo with the message "no command" shows up
3) Press and hold "volume down", then Press "back" button then release "back" button and the menu will show up. Then release "volume down".
4) use "volume up" or "volume down" to navigate menu
5) to execute selection, use "home" button
I hope it helps someone.
If so, please tell me.
Total first timer, flash to stock as had messed up sd card partition trying to flash custom ROM, really worried when couldn't access recovery after stock flash. Thank you thank you thank you, this totally worked!!!
thank you a lot. saved my phone. i thought i will through away the nexus 4 but the combination of no command power button and volume up did well
Hope this helps, you press and release volume up! worked perfectly
Performing a factory reset may take some time, so make sure that you plug your device into a power source before you start. If your phone becomes unresponsive at any point during these steps, you can restart it by holding down the Power button for several seconds.
If your phone is on, turn it off.
Press and hold the Volume Down button and the Power button at the same time until the device turns on. You'll see the word "Start" with an arrow around it.
Press the Volume Down button twice to highlight "Recovery".
Press the Power button to restart into Recovery mode. You'll see an image of an Android robot with a red exclamation mark and the words "No command".
While holding down the Power button, press and release the Volume Up button once.
Press the Volume Down button twice to highlight "wipe data/factory reset" and press the Power button to select it.
Press the Volume Down button seven times to highlight "Yes - erase all user data" and press the Power button to select it.
After the reset is complete, press the Power button to select the option to reboot your device.
When you've finished, follow these steps to restore your data.

[Info] Guide to entering safe mode, bootloader, stock recovery

Yes, I know, everyone knows how to enter safe mode, bootloader, and recovery.
I found there are some inconsistencies to entering and using recovery depending on your which software you are running. In addition there are multiple ways of entering stock recovery.
Also I always see people asking this question because somehow the keypress order is not intuitive.
Entering Safe Mode
Tablet booted and running Android
Press/Hold Power button until power menu shows up
Tap/Hold Power off option
Choose OK to reboot in safe mode
Tablet powered down
Press/Hold Power button until Google screen shows up, RELEASE Power button
Press/Hold VolDn until Android has booted up
If successful, you will see Safe mode overlayed on bottom left of screen.
Entering Bootloader (ie fastboot mode)
Tablet booted and running Android
From adb
adb reboot bootloader
can also choose recovery from menu after bootloader comes up
From app
Use Quick Boot from Google Play
Tablet powered down
Power+VolDn while booting to enter bootloader
Release buttons after you see bootloader screen
Entering Stock Recovery
Tablet booted and running Android
From adb
adb reboot recovery
From app
Use Quick Boot from Google Play
Tablet powered down
Power+VolUp while booting to enter recovery
You can release buttons after you see Google on screen
When Stock Recovery starts you will see the Android fallen down screen
To bring up the Recovery menu
Power+VolUp to show recovery menu
Must be this sequence Press/Hold Power, THEN Press/Release VolUp, release Power
Within menu
VolUp to move up
VolDn to move down
Power to select
In addition, I found an inconsistency with JSS15J stock recovery that wasn't in the JWR66N recovery
While at the Android fallen down screen if you mistakenly press
VolUp
instead of
Power+VolUp
you will still get the Recovery menu.
However, VolUp will no longer function. It will instead become a toggle for switching between the Recovery menu and the Android fallen down screen
Android fallen down screen
VolUp to toggle recovery menu
Within menu
VolUp does not work since it toggles recovery menu
VolDn to move down
Power to select
sfhub said:
Entering Stock Recovery
Tablet booted and running Android
From adb
adb reboot recovey
Click to expand...
Click to collapse
Are you sure with this command. I think it must be => adb reboot recovery <= or am I wrong ???
pRo_lama said:
Are you sure with this command. I think it must be => adb reboot recovery <= or am I wrong ???
Click to expand...
Click to collapse
Sorry, typo, fixed.
i`m on completely stock JSS15Q and i cant get into stock recovery. When im trying i see "no command" and red exclamation mark on the laying robot. What should i do?
laska300 said:
i`m on completely stock JSS15Q and i cant get into stock recovery. When im trying i see "no command" and red exclamation mark on the laying robot. What should i do?
Click to expand...
Click to collapse
sfhub said:
Entering Stock Recovery
Tablet powered down
Power+VolUp while booting to enter recovery
You can release buttons after you see Google on screen
When Stock Recovery starts you will see the Android fallen down screen
To bring up the Recovery menu
Power+VolUp to show recovery menu
Must be this sequence Press/Hold Power, THEN Press/Release VolUp, release Power
Within menu
VolUp to move up
VolDn to move down
Power to select
Click to expand...
Click to collapse
Please see RED section
Does the presence or absence of the red exclamation triangle mean anything?
Wot does safe mode do?
Anderson2 said:
Does the presence or absence of the red exclamation triangle mean anything?
Click to expand...
Click to collapse
I don't remember if there are two images one with and one without the triangle. I think I've only seen the image with the red exclamation point.
I've never seen anything to indicate the red exclamation mark is something you need to pay attention to.
Now if you apply an update and there is an error, then that is something I would pay attention to.
LoVeRice said:
Wot does safe mode do?
Click to expand...
Click to collapse
It doesn't load the stuff you added.
It is similar to safe mode on a PC, used to diagnose whether the issue is in the stock ROM or is in something you introduced by installing some app.
I Have a probleme
since a bought TAB 3 10.1 and it's boot into safe mode i'v restart it and turrn it off the back on but it didn't go what should i do ?
This thread is about nexus 7.
sfhub said:
This thread is about nexus 7.
Click to expand...
Click to collapse
oh sorry i was panic so i searched in every thing
Bootloader
If none of that works, try the command with a dash "adb reboot-bootloader" Depends on your device sometimes, sometimes unplugging your device right after you enter this command will keep it from getting stuck at the boot logo screen. If that doesn't work, hold the power button to power device down and then boot it into recovery instead using the button combo. Then you can wipe cache & start all over again.
I'm not even able to get into Recovery. I can get to the bootloader, then I select "Recovery mode" and it shows the Google logo, but it never goes into recovery. I have let it sit at the Google logo for a couple of hours, and end up just holding down the power button to shut it down.
I have tried Skipsofts toolkit, as well as Wug's, to try to unlock the bootloader. This ends up with the device hanging at the "Unlock bootloader" screen after selecting "Yes". Again, I have left it in this state for well over an hour with no change.
Here's some info on my 2013 Nexus 7:
KitKat 4.4.4
Never rooted
Never unlocked bootloader
HW version rev-e
Bootloader version FLO-04.02
I suspect my Nexus knew I was supposed to go on travel next week and is faking sick.
Any help would be appreciated. Thanks.
Hi guys i have a google nexus 5 and it is locked state. It is getting booted again and again but it jiust reaches google logo and again restarts. Safe boot is also enabled so i cant enter in recovery mode also. Please help me ASAP.

[Q] HELP, my nexus 7 cant open settings

So, the thing is after i update my nexus 7 to JB4.3, I cannot open the settings menu at all, when i try to open the settings menu, this thing keep pop out "Unfortunately, com.android.settings has stopped". So, I tried to reset it the "HARD" way to factory settings. After I did that, everything seems normal until the I try to choose the language. Guess what? this thing pop out again, "Unfortunately, com.android.settings has stopped". Up to this point, I dont have any idea how to solve my problem. I have spent like half day try to search for this problem from multiple forums. I really hope that somebody can help me from this misery. Thanks alot.
Try a factory reset..
If your tablet is on, power it off.
Press and hold Power until the device powers on, then immediately press and hold Volume Down (while still pressing Power). You will see the word Start with an arrow drawn around it.
Press Volume Down twice to designate Recovery mode.
Press Power to restart into Recovery mode. You will see an image of an Android robot with a red exclamation mark.
While holding down Power, press Volume Up.
Use the volume keys to scroll to "wipe data/factory reset" and press Power to select it.
Scroll down to "Yes - erase all user data" and press Power to select it.
Note that you will lose all apps, etc.
danvee said:
Try a factory reset..
If your tablet is on, power it off.
Press and hold Power until the device powers on, then immediately press and hold Volume Down (while still pressing Power). You will see the word Start with an arrow drawn around it.
Press Volume Down twice to designate Recovery mode.
Press Power to restart into Recovery mode. You will see an image of an Android robot with a red exclamation mark.
While holding down Power, press Volume Up.
Use the volume keys to scroll to "wipe data/factory reset" and press Power to select it.
Scroll down to "Yes - erase all user data" and press Power to select it.
Note that you will lose all apps, etc.
Click to expand...
Click to collapse
I have done that already. And after i reboot, I cant proceed further because when I try to choose the language, the same message pop out again "Unfortunately, com.android.settings has stopped" Any idea about this?
Did you upgrade via a OTA, stock image, or a rom download? Also, did you verify the md5 checksum?
Sent from my Nexus 7 using Tapatalk 4
Wugfresh Nexus Root Tool
Reflash stock 4.3.....
I'd reflash the system.img.
Sent from my Nexus 7 using Tapatalk 4
My nexus7 actually has never been rooted and I'm actually new to Android, so I am a bit dumb
But, i'm a quick learner, I will appreciate it if somebody can guide me step by step.
What about fix permissions command in recovery? Along with a dalvik and cache wipe?
Sent from my Nexus 7 using xda app-developers app

[Guide] What to do when TWRP won't boot from fastboot

Here's the fix I found for when "fastboot boot twrp.img" leads to a frozen Google logo screen
1. Go into the bootloader (shut down, then hold volume down and power together)
2. Choose "recovery mode"
3. Wait until you get the broken android that says "no command"
4. Press volume up while holding the power button to show a list of commands
5. Choose factory reset
After going through these steps, TWRP finally loaded! It took me a couple hours to figure this out, hope it helps others with the same issue save time :good:

Categories

Resources