hello!
i got a question. i tried to get a energy rom on my phone. i did everything said in this thread: [TUT] Dummies guide: flashing 1.56+ roms [v 2.0] - [HSPL]
updated drivers, had SPL 1.54.0000 on my phone and followed the instructions. when i executed USPL and did the following step in the guide:
"(USPL5b) Run USPL.exe from the download in step (USPL1c)...When the application appears click on Run USPL."
the programs output said everything is fine and the phone turned off like it should do. the only problem is, it did restart and i also cant switch it on with the power button... any suggestions?
regards
there is 2 points of view to this:
1. how did you actually end up where you are now?
2. and how do you solve that (probably depends on 1.)?
so:
1.
- did you, by any chance, ignore the warning to only flash with a full battery?
although a cable is plugged in, during the stages of flashing the device is not charged, but actually uses a lot of power, due to the fact that the screen is backlit the entire time and the nand is constantly accessed.
- could your usb cable be faulty and have terminated the connection midway through?
that could mean that you now have a broken spl, which is not much better than no spl at all.
2. some of the most primitive ways of getting the device back to life might be:
- have you tried switching it on with VOL- pressed (bootloader mode) instead of actually switching it on? (also, in that case, which spl is shown?)
- have you taken out the battery for half an hour and put it back in then and tried to switch it on or enter bootloader mode?
- do you have any way of either testing the battery outside of that specific device or charging it externally? (to make sure it is not actually empty, because in this state, your device might not charge it)
- and lastly, have you done this procedure before?
are you sure, you followed it to the letter? because any indication of going off-script might help us find the cause and then the solution to your problem.
if we can make sure, that your phone is not physically harmed (battery, usb connector...) and you are not in the worst luck about the timing of the error, we should be able to fix it.
Hi
to start you phone again you have to press "both" volume button down, at the same time you have to press the reset button as well,reset button is beside you SD Card on the back of you phone ,when you press all the button you will see a 3 colored screen on you phone if you see the 3 colored screen stop pressing the volume button,after that it is everything explaind on the phone screen.With this method you will delete everything on you phone and be back on you original phone settings.
no, that would be a hard reset and it does not affect the spl, without a proper spl, the phone cannot boot and a hard reset cannot change that, he needs to access bootloader mode to flash an spl and then a rom.
Related
My g1 has developed some fault where it keeps restarting.
At first I assumed my SD card was dead so I bought a new one, however it is still restarting.
At first it seemed like the SD card was causing the problem however it does restart without having an SD card in it, sometimes it won't boot at all even to recovery, it just keeps restarting.
It all started last week randomly, didn't drop it or anything.
It doesn't matter what rom is on it, seems to be a hardware fault.
It can work for a bit then if I pick it up it will restart, adb logcat doesn't show anything either.
Any suggestions?
Eh had this happen to a friend, he returned the phone for a new one. If you still have warranty it'd be wise to check out.
I want to unroot it to take it back but I have the danger SPL..
Is flashing DREAIMG from danger SPL the only thing required to go back to stock?
I'm following
>http://wiki.cyanogenmod.com/index.php/Full_Downgrade_Guide_-_CyanogenMod_to_Stock
However I am stuck at step 5
"# Follow the on-screen instructions to flash the image. On some G1s it may require pressing the action button (trackball), while on others it may require pressing the power button. "
My G1 says to press the power button to flash, however it just restarts when I press it
Turns out the g1 restarts when ever presure is applied to the hardware keys, going to tmob to for a fix tomorrow.
Mods delete this
Reading the "How to root" thread here. I've rooted a few G1's and a MT3G in the past.
Anyways. I downgraded to RC29, downloaded Amon's recovery and Hard SPL.
Did the whole Telnetd, downloaded telnet from market and mount remount, flash yadda yadda as per stated.
Rebooted and applied the Hard SPL.
After that finished I rebooted and it just hangs on the G1 screen, Home/Power does nothing. Camera/Power does nothing. Trackball/Power just lights the LED up blue.
Will it live the rest of it's life as a door stop?
not being able to boot into anything is a brick but there have been many threads about people who have somehow reversed their brick so just search this forum and see if anything happends who knows it could happen. otherwise its a really shiny paper weight
Bummer. I'll search around a bit more and see if there might be a thread I missed. I don't want to dig into it and do the whole jtag crap since there is still a warranty on the phone.
This is the "How-to" thread I followed and has worked on every G1 I have rooted til this phone which is a brand new one from Tmo.
http://forum.xda-developers.com/showthread.php?t=442480
Searching more I have read about people not flashing a radio before the SPL and caused a brick. If that is true why doesn't it state this as a necessary step?
Flashing the Radio before the SPL is needed for DangerSPL (although I seem to recall a thread debating that - http://forum.xda-developers.com/showthread.php?t=655097 ), I didnt think it was needed for HardSPL, it sounds like a brick unfortunatly, but I am no expert.
It is thought that its safer to flash the SPL and radio ect via fastboot (see link above) , not that it helps to much now, but that is an old guide, it should be updated though
Yep. From what I have gathered is if you can't get into recovery (home+power) or fastboot (camera+power) and it hangs on the G1 boot screen. It's a brick.
-RotorDemon- said:
Yep. From what I have gathered is if you can't get into recovery (home+power) or fastboot (camera+power) and it hangs on the G1 boot screen. It's a brick.
Click to expand...
Click to collapse
its not a brick unless it doesn't turn on at all (depending on how you define the word "brick")
exact same thing happened to one of the G1 replacements my friend got sent to him...we sent it back and they sent him a new one
Nah it's not bricked, the HSpl isn't compatible with your ROM, try flashing he ROM again, or faulty ROM this happens a lot.
Howto fix:
1. Backup any files on your SD card that are valuable to you (you can copy them to your PC's hard drive)
2. Format your SD card to FAT32 ( put your SD in your PC)
Windows: Right-click on SD icon and select format
3. Download the RC29 / RC7 dreaimg.nbh file (don't rename it or your phone won't recognize it):
RC29 (US): http://wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_G1/Dream_Firmware_to_CyanogenMod
RC7(Europe):http://wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_G1/Dream_Firmware_to_CyanogenMod
4. Put the file you just downloaded onto your freshly formatted SD card (make sure it is named DREAIMG.nbh, the rc7 file downloads with .NBH which is wrong)
5. Turn your phone off.
6. Hold down the Camera button, and press the Power button until the bootloader starts.
Note: On some G1s it may require pressing the action button (trackball), while on others it may require pressing the power button.
7. Follow the on-screen instructions to flash the image.
8. When it's done, press the trackball.
9. Press the Call, Menu, and Power buttons at the same time to reboot. You may need to unplug your phone for this to work.
10. And you're done, your phone is in Manufacture default-settings.
If you want to flash a ROM follow a guide (start from the beginning)
Tell me if it worked or didn't worked!
Source: http://wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_G1/Dream_Firmware_to_CyanogenMod
what tally said....
but on the one i described, just to let you know, i flashed the rc29 dreaimg.nbh like 15 times, it would never get off the G1 boot screen
tnpapadakos said:
what tally said....
but on the one i described, just to let you know, i flashed the rc29 dreaimg.nbh like 15 times, it would never get off the G1 boot screen
Click to expand...
Click to collapse
Try flashing the ROM again if you can go to the bootloader(Rainbow) screen try this:
1. take out the SD card
2. download this file ,open the folder and paste the dreaming.NBH file to the root of your SD card(use your pc or another phone to past this on your SD card).
2. you should get a gray screen once the card in placed back into the phone
3. then press power to start update
4. once the update is complete press the track ball then the rainbow(bootloader) screen should come back up,
5. pull out the battery and there you go your phone should work again
Note: If it didn't updated turn of your phone and turn it on by pressing (& holding) Power+Camera button.
Tell me if it worked
Lol, for some reason it double posted my previous post sorry.
He says in the first post Camera / Power dosent load the bootloader
vixsandlee said:
he says in the first post camera / power dosent load the bootloader
Click to expand...
Click to collapse
send it back
vixsandlee said:
He says in the first post Camera / Power dosent load the bootloader
Click to expand...
Click to collapse
Yes I know but if he connects it to he's PC and turns it off and on and then go to bootloader it will work.
tally114 said:
Yes I know but if he connects it to he's PC and turns it off and on and then go to bootloader it will work.
Click to expand...
Click to collapse
Interesting, I didnt know that.
Thanks for the info.
tally114 said:
Yes I know but if he connects it to he's PC and turns it off and on and then go to bootloader it will work.
Click to expand...
Click to collapse
Doesn't work either. Connected, disconnected, SD card in or out, SIM card in or out and any combination of that.
Logcat just sits and says "Waiting for device" while the phone just hangs on the G1 screen. So unless there is a different way to get into the bootloader besides using Camera+Power I'd like to know.
Camera+Power and Home+Power are unresponsive.
Well... it sounds like you've got yourself a fancy plastic brick, just remember for next time
1. Downgrade
2. Radio
3. Spl
-------------------------------------
Sent via the XDA Tapatalk App
Hi,
After upgrading to new ROM I performed hard reset on my vx6900. At the last screen during hard reset pocedure I press Send button as requested and it was a last time I ever saw something on my screen. Device is not waking up anymore when I plug power it always the red led is switching on (with or withoout batery). I took a 100% charged batery from another device, but it's not helping. I'm out of options I think I tried evrething: Hard reset combination, bootloader combination, keep it on charge for hours, then without battery for hours - no luck.
Could anybody help me?
fofan said:
Hi,
After upgrading to new ROM I performed hard reset on my vx6900. At the last screen during hard reset pocedure I press Send button as requested and it was a last time I ever saw something on my screen. Device is not waking up anymore when I plug power it always the red led is switching on (with or withoout batery). I took a 100% charged batery from another device, but it's not helping. I'm out of options I think I tried evrething: Hard reset combination, bootloader combination, keep it on charge for hours, then without battery for hours - no luck.
Could anybody help me?
Click to expand...
Click to collapse
Had you been switching to Android (NAND Flash)?
No, I performed hard reset after succefully loading NFSFAN's WM6.5 1.00 FINAL ROM.
Before NFSFAN's WM6.5 1.00 I loaded Vogue_unlocker_MFG-2.31 (initial attempt to load NFSFAN's WM6.5 without unlocker didn't work).
Is there any way to revive it after Red Led?
If you cannot put your device in bootloader, then you are toast
How are you trying to put the device in bootloader?
I guess it dead then Not waking up into boot mode after Pwr-snd-reset.
Also I tried any combination of buttons with reset. It is not waking up. And it is strange to me because I was just performing hard reset and following the screen prompt. Now I don't see any activities except this stupid red led. I though there is some sort of reincarnation procedure some "hard hard" reset?
To enter the Boot Loader mode....
Press and hold the following buttons:
Power (on top left of device) + Camera (on right of device, near the bottom) + Reset (small hole on bottom right of device, just right of the USB port. You can press this with the tip of your device's stylus).
It can be tricky to press all 3 of thes buttons at the same time, and you will probably need to use both hands.
You should see an odd rainbow on screen, indicating that you are in the Boot Loader mode. The device does not need to be connected to a computer of charger in order to enter Boot Loader mode.
If this does not work you may actually have the 1st bricked vogue I've ever seen...
(It didn't get wet, did it...?)
antinerd said:
Press and hold the following buttons:
Power (on top left of device) + Camera (on right of device, near the bottom) + Reset (small hole on bottom right of device, just right of the USB port. You can press this with the tip of your device's stylus).
It can be tricky to press all 3 of thes buttons at the same time, and you will probably need to use both hands.
You should see an odd rainbow on screen, indicating that you are in the Boot Loader mode. The device does not need to be connected to a computer of charger in order to enter Boot Loader mode.
If this does not work you may actually have the 1st bricked vogue I've ever seen...
(It didn't get wet, did it...?)
Click to expand...
Click to collapse
That is exactly why I was asking. What you are doing with power +vol keys is for the TP and not for the Vogue.
I used boot loader sequence already (pwr + camera + reset) between all other sequences it doesn't help, device is no show any vital signs the only thing that works is a red led.
I also noticed that when I power it up without batery and then insert the battery the red led is going away. Then Red led is blinking every time I press the reset.
It sounds that you may have fried your NAND...
Just to be sure, you didn't bump it, throw it, or sent it for a swim... have you?
Have you tried this?
http://forum.xda-developers.com/showthread.php?t=694798
May not work, but it is worth a shot.
Guys, when you get a red LED, it means your battery is fried. It's near summer so are you sure you didn't charge it in the car or something? Replace your battery and you'll be fine.
atoz350 said:
Guys, when you get a red LED, it means your battery is fried. It's near summer so are you sure you didn't charge it in the car or something? Replace your battery and you'll be fine.
Click to expand...
Click to collapse
The OP already stated that he tried a 100% charged battery from another Vogue and nothing.
No, I didn't do anything brutal to that device, as i said it was absolutely responsive when I started the hard reset sequence and it had not history of stuck buttons, anyways I'm going to doublecheck all buttons to make sure nothing stuck and preventing it from boot (looks like it my last hope )
If that doesn't work. open it up and clean the dust and debris out of there with a can of spray air. There might be a spec of dust that is causing a short circuit. That actually happened to me during the 80386 days when I was putting together a computer and it wouldn't get past the post screen. Turned out, there was a spec of dust lying across 2 pins on the CPU.
I keep my phone in my pocket and every now and again I take the back cover off and there is a ton of dust in there.
Good luck.
So? Any news? Could you revive it?
Use this it will be fine as i have used it once!!!
Edited *This will help those that are stuck at the HTC welcome screen and cannot get past it to load IMCokeMan's Unlocker.**
Edit by ImCoKeMaN: If you are stuck in bootloader (3 color screen) use titanexitbl or mtty (set 16 0 then task first and try these steps only if that doesn't work.
Apparently you can not use SDHC cards with this method, please use the 512mb card that came with your phone.
I have successfully unbricked my phone due to updating the Alltel rom to a non Alltel Vogue, before IMCokeman had released his unlocker an also have downgraded to the previous SPL version. I will shortly update this post with the How to instructions. I just need to retrace my steps.
I would first like to thank IMCokeMan for his help and unlocker.
I currently have a Sprint Vogue but I assume this will work for all versions
For those that had loaded the Alltel rom without the unlocker and have bricked there phone try this procedure to unbrick your phone.
1. First download IMCokeMaN's 2.31 Unlocker. http://rapidshare.com/files/11019074...r_MFG_2.31.exe
2. Extract IMCokeMan's unlocker
Previous SPL version was 2.31 current SPL version is 0.36
Edit by ImCoKeMaN:
Note: Steps 3, 4 and 5 should not be necessary, but step 6 is critical that it is a signed rom from your carrier
3. Navigate to the extracted folder and within the folder you will find the following file called VOGUIMAG2.nbh and rename it to VOGUIMG.nbh
4. Copy the file to a fat32 memory card, and insert it back into your phone, and place it into bootloader mode.
5. The phone should display Loading... let it sit there for a minute or so. It will not go past this screen, now reboot the phone.
6. Extract your official rom (Must be a signed EXE from your carrier, check here)
7. Navigate to the extracted folder and within the folder you will find the following file called ruu_signed.nbh and rename it to VOGUIMG.nbh
8. Copy the file to your memory card (less than 2gb and formated fat32) and insert it back into the phone and place it back into bootloader mode, and install the your Carrier's Official ROM.
patelaquib said:
Edited *This will help those that are stuck at the HTC welcome screen and cannot get past it to load IMCokeMan's Unlocker.**
Edit by ImCoKeMaN: If you are stuck in bootloader (3 color screen) use titanexitbl or mtty (set 16 0 then task first and try these steps only if that doesn't work.
Apparently you can not use SDHC cards with this method, please use the 512mb card that came with your phone.
I have successfully unbricked my phone due to updating the Alltel rom to a non Alltel Vogue, before IMCokeman had released his unlocker an also have downgraded to the previous SPL version. I will shortly update this post with the How to instructions. I just need to retrace my steps.
I would first like to thank IMCokeMan for his help and unlocker.
I currently have a Sprint Vogue but I assume this will work for all versions
For those that had loaded the Alltel rom without the unlocker and have bricked there phone try this procedure to unbrick your phone.
1. First download IMCokeMaN's 2.31 Unlocker. http://rapidshare.com/files/11019074...r_MFG_2.31.exe
2. Extract IMCokeMan's unlocker
Previous SPL version was 2.31 current SPL version is 0.36
Edit by ImCoKeMaN:
Note: Steps 3, 4 and 5 should not be necessary, but step 6 is critical that it is a signed rom from your carrier
3. Navigate to the extracted folder and within the folder you will find the following file called VOGUIMAG2.nbh and rename it to VOGUIMG.nbh
4. Copy the file to a fat32 memory card, and insert it back into your phone, and place it into bootloader mode.
5. The phone should display Loading... let it sit there for a minute or so. It will not go past this screen, now reboot the phone.
6. Extract your official rom (Must be a signed EXE from your carrier, check here)
7. Navigate to the extracted folder and within the folder you will find the following file called ruu_signed.nbh and rename it to VOGUIMG.nbh
8. Copy the file to your memory card (less than 2gb and formated fat32) and insert it back into the phone and place it back into bootloader mode, and install the your Carrier's Official ROM.
Click to expand...
Click to collapse
The OP is not stuck in bootloader. His device simply doesn't turn on.
Unfortunatelly nothing helps. I opened it up, even unscrewed completely and sprayed with dust remover. It's the same.
What I noticed is when I plug device to power without battery the red led goes on (it's normal behavior for all devices). Then I insert the battery while device is still plugged in (in my case to Laptop's USB). The red led goes away (also normal behavior for devices). Then I can hear USB connect sound from laptop and in few seccond message: "USB device not recognized".
Click on reset button causes device's Red Led to blink and I can hear USB re-connect sound from Laptop again. Any other buttons or combination of buttons on device don't do any diffrence.
You are only trying to charge via USB? You should have said this earlier. Get a charger (output of 1 A). I had the same thing happen to a Wizard once and I used a high output charger and it worked again (battery was brand new too).
USB cable was one of my desperate try-outs, before I was keeping it on stock HTC (1A) charger for days, with empty and full battery in and no luck
Hi,
I was trying to update my phone to latest Froyo dragon and it was not booting. I then flashed it to Gingebread Yoshi but was happy with it so tried Froyo dragon again and noticed that I needed to update the radio.
I updated the radio it and seemed ok but then my battery dropped out. Now it will not boot pass the "MyTouch 3g" green splash screen. From investigating it seems that because hboot and radio are not matching versions this is the problem.
I cannot get into recovery mode at all. I cannot get in Fastmode or Hboot nor use AdB as usb it is not recognised by my computer. I have tried a few different computers but non recognise it. Blue led with trackball+power is the only key combo that works.
Things i have tried:
- Fully charged phone and left it on but it just goes flat eventually.
- Tried all different combinations to boot Vol down+Power, Back+Power, Home+ Power, Trackball down plus power loads with black screen and blue led.
- Downloaded various sappimg.zip and SAPPIMG.nhb files to sd using adaptor and tried to boot with no luck.
- I have also created a couple of goldcards but didnt make any difference.
Any other suggestions or do I just have a paperweight?
Is there other files that I can put on the goldcard so I can access recovery?
Does the phone need to have a valid SIM card in order to get into recorver,hboot,fastboot, or just to boot. I did try a sim once but did not go back to it.
Thanks for taking the time to read and respond.
Regads,
Arch
No, i don't think you need a SIM-card to get it running - didn't need one to debrick mine.
So, you tried many things, but i don't think there is a way to flash the phone with sappimg.zip or nbh because you don't get into fastboot mode.
What you can try:
- remove battery for some time (5 minutes or whatever) and press power - then get the battery back in and try to start it again
- start the phone with Home+Back+Power or Menu+Back+Power (don't remember), in my case there was a menu to erase cache and so on, maybe this would work for you
- is your phone listed in "fastboot devices" when you power on your phone with Vol down+Power, Back+Power, Power, Home+Power or the combination from above? I read that some people are already in fastboot-mode when they see the logo, shown for example here (they had red text on red vodafone-logo):
http://www.android-hilfe.de/attachm...oter-vodafone-bildschirm-geloest-dsc00624.jpg
If nothing works the only way to get it back to life is JTAG, maybe you can find someone who's doing that (where are you from?).
Hi Thanks,
Tried all above but no dice.
Anything else I could try. I am in Australia so don't know anyone with Jtag. I guess I may just have to sell it for parts. Seems such a shame though
Hopefully somebody finds a way.
Sorry, but i think there's nothing you can do for your phone. :crying:
Bluelight-Mode works (Trackball+Power), so only JTAG will help, but i don't know how to find this service in your area. Search for a repair-shop with JTAG in your area or ask here at XDA or some other community. Maybe find that service on ebay.
Another possibility is that you buy a Riff Box and learn how to unbrick your phone yourself - maybe provide your service for some other people around your area and earn the money you payed for the Riff Box. :laugh:
Good luck!
My 6T is currently a paperweight (bricked, screen won't turn on, no fastboot, no nothing) and here's the succession of events that led to it:
I live in the US and bought the unlocked 6T.
1) A few weeks ago I rooted it with same steps described in this post --> https://www.xda-developers.com/oneplus-6t-unlock-bootloader-root/. Everything seemed to go well, I had Magisk and my phone worked just fine.
2) About a week later I got a notification that my phone had a software update ready. I idiotically obliged and installed it. After the install, I still got the bootloader unlocked screen at start up so I thought my phone might still be rooted. However, I couldn't download any mods on Magisk and my root checker said I was no longer rooted. So basically, my phone appeared rooted (apps like Google Pay wouldn't work, I got the warning about the Bootloader at start-up, etc.) but I no longer had the benefit of being able to install mods through Magisk.
3) A few weeks later (yesterday) I decided I would explore options for un-rooting, mainly so I could use Google Pay again. Remember, my phone wasn't actually rooted anymore, since the update. So I thought locking the bootloader should fix my problems. I did that with fastboot oem lock and then my phone was stuck in a fastboot loop. I tried every option in fastboot and would just end up right back there. I started looking for fixes and came across the MSMDownload Tool --> http://https://forum.xda-developers.com/oneplus-6/how-to/tool-msmdownloadtool-v4-0-international-t3798892. I downloaded the driver, it recognized my device, I downloaded the tool, then ran it. At 16 seconds, the download stopped and I got an error saying "Sahara communication failed." After looking up a fix that involved holding down the volume+ button, I decided I'd try again. This is where I f*cked up. I unplugged my phone without stopping the download, and that leads us to this very moment. My phone does not turn on at all. I have no access to fastboot or anything. My computer does recognize it when I plug it back in (I'm on Windows).
If you read this it's probably obvious that I only know enough to be dangerous and bricking my phone was inevitable. Feel free to call me an idiot, I only ask that you provide some useful information, preferably on the subject of getting my phone working again. Thank you all in advance. I hope this post isn't redundant. I didn't find anything on here that was a fix for my situation. I'm also open to contacting OnePlus if anyone thinks I should do that first. I genuinely thank anyone that takes the time to read/help! xd
Use the msm tool...doesn't use fastboot
Edit...nevermind
You need to get your phone to show up as "US8_BULK" like in the MSM thread you linked. You can do this even if your phone wont boot properly. I have done it multiple times before. When in the Qualcom flashing mode the screen will not light up at all.
Hold all the buttons until it resets. This could take up to 30 seconds of holding the buttons. The just follow the steps in the MSM thread starting with this one:
Power off the phone, then hold for 5 seconds vol up and plug the usb to computer. Now you have to see US8_BULK as new device connected and you can also see in device manager; if you can't notice it, repeat the process until you see it (power on, power off, hold...) there is a full youtube guide for op5 and it's the same process - (https://www.youtube.com/watch?v=PpLvmID1wdI)
Edit: It can take some practice to get the timing down, especially if your screen is not coming on at all. Just keep trying as you will be able to get into that Qualcom flashing mode unless there is physical hardware damage to your phone.
Jager said:
You need to get your phone to show up as "US8_BULK" like in the MSM thread you linked. You can do this even if your phone wont boot properly. I have done it multiple times before. When in the Qualcom flashing mode the screen will not light up at all.
Hold all the buttons until it resets. This could take up to 30 seconds of holding the buttons. The just follow the steps in the MSM thread starting with this one:
Power off the phone, then hold for 5 seconds vol up and plug the usb to computer. Now you have to see US8_BULK as new device connected and you can also see in device manager; if you can't notice it, repeat the process until you see it (power on, power off, hold...) there is a full youtube guide for op5 and it's the same process -
Edit: It can take some practice to get the timing down, especially if your screen is not coming on at all. Just keep trying as you will be able to get into that Qualcom flashing mode unless there is physical hardware damage to your phone.
Click to expand...
Click to collapse
Awesome, that worked! I kept seeing I needed to hold volume+ and power but holding both and power is what actually worked for me. Thanks a lot my friend
@lapitman, glad to see that you finally got it to work!