Database Users

[Q] Please help! flashed P1000XWJMK and now my tab stuck a "Galaxy tab"

hi,, anybody please help!!.. i was using Roto JME full v4 and then i Flashed my tab with P1000XWJMK ..
but then it turned to fail in odin.. and now it stuck on galaxy tab logo even though when i flashed back with ROTO JME full v4 it says it 'Pass'..
anybody can help??? pleaseee...
*I Still can access download mode.. and detected by Odin.. i hope i still have chance. and please help me step by step since im too noob. im sorry

Just set everything up and flash again. Double check the instructions. Don't worry, your tab will be fine.

Get a stock rom package (any of Rotohammer's firmwares will work)
Get P1_add_hidden.zip and extract the P1_add_hidden.pit file
Using Odin 1.7, put stock rom (Roto-JME-Full-v4.tar for example) in PDA slot.
Put P1_add_hidden.pit in Pit slot
Check repartition box
Put Tab in download mode by holding Volume Down and Power, connect to the computer, and press start.
After this, the Tab will reboot normally. Shut it down and return to download mode.
Open Odin 1.7 and reconnect the Tab.
In the PDA slot, choose the Overcome Kernel v2.0 tar file for use with Odin. Press start
It will flash the kernel then reboot. Upon reboot, you should hear the sexy robot voices informing you of the status of the EXT4 conversion.
Once done, the Tab will boot normally. At this point you can load Overcome Rom (or any other Rom of your choosing)

@rangercaptain : I did that,, it flashed successfully but still stuck
@btyork : i Did that too yet same,, stuck
heellllppp

I also cannot access recovery mode.. ive searched some thread regarding my problem and it seems all of them sent their tab back to warranty,, is there really no chance for me??

Nope, I tried I tried....
Off to the repair center, I think

1. Go to http://www.samfirmware.com/WEBPROTECT-p1000.htm and download the firmware for your device. (you must register first)
2 download the flashing guide and make sure you follow all the steps http://www.samfirmware.com/SVC Android/P1000 Flashguide.pdf
Sent from my GT-P1000 using XDA App

[JVH Install Help] Bell Canada

Here's what I did to get JVH (with 850mhz band) and CSC for Canada on my phone. It worked for me at least
Files:
SpeedmodK15E_withLoaders.tar.md5 (8.38 MB)
http://www.multiupload.com/SRVH1BTK8R
JVH_KC1_BMC.zip (169.32 MB)
http://www.multiupload.com/1FHETKJOWA
StockJVH_Kernal_noLoaders.tar.md5 (5.47 MB)
http://www.multiupload.com/PM3AXR7JFG
**************Disclaimer:***************
I'm not responsible if this bricks your phone, as "the boss" said if I break mine, she'll break me... or I get a $20 replacement phone
Backup your /efs folder, backup EVERYTHING, just in case... I'm paranoid so I did it all
ROM NOTES:
Got deodexed from here:
http://forum.xda-developers.com/showpost.php?p=11256520&postcount=1
Modem:
KC1
Busybox:
1.18.4
Hosts file updated for ad blocking using:
http://winhelp2002.mvps.org/hosts.htm
Here's the steps I followed:
Save all files to folder/desktop
Connect phone via usb and copy JVH_KC1_BMC.zip to root of sdcard
Restart phone in download mode
Open Odin and click PDA
Select Speedmod tar file
Uncheck Auto-Reboot
Check F.Reset Time (I don't know what it does, but it's always checked)
Flash the tar.
Once complete and the box says "PASS" in green, unplug your phone and pull the battery (I was told it's safe, as it's in the MIUI instructions as well)
Put battery back in and start phone in recovery with VOL UP+HOME+POWER
In recovery choose to update from zip
Choose file from sdcard
Choose the JVH_KC1_BMC zip file and update
The phone will restart/install.
Once it's started up for the first time I recommend restarting in download mode and flashing the stock JVH kernal
You can also use any kernal you want.
Let me know if I can help at all. I was trying to make a completely odin flashable tar for this but failed miserably :9
I'll do my best to answer any questions however this is my first time making something to flash for you all
Note:
I'm not sure where to put this, sorry to mods/admins if it's in the wrong spot, please let me know

Hi,
I saw your thread, and I found it very interesting for people who own a Bell SGS 9000m Vibrant and wanna upgrate to Gingerbread.
So I decided to flash the Gingerbread JVH ROM just like you did, but I need to know a few things:
1. Will I be able to downgrade to my original stock froyo after this flash ?
2. Will I be able to update via Kies in case Bell release an official gingerbread update ?
3. Right now my phone is SIMUnlocked, will I lose my SIMunlockation after the flash ?
4. And is my actual configuration right to excecute this flash or should I flash something else before ?
My configuration is the following:
Baseband version
I9000UGJL2
Firmware
2.2
Kernel
2.6.32.9
[email protected] #3
Build number
FROYO.UGJL2
galaxy s vibrant bell
gt-i9000m
Thanks for your hard work, I hope to read back from you soon.

I have exact same configuration and exact same questions as poster above!!!

Still no answer... Guess we'll have to try if wanna know...

nguetto said:
Hi,
I saw your thread, and I found it very interesting for people who own a Bell SGS 9000m Vibrant and wanna upgrate to Gingerbread.
So I decided to flash the Gingerbread JVH ROM just like you did, but I need to know a few things:
1. Will I be able to downgrade to my original stock froyo after this flash ?
2. Will I be able to update via Kies in case Bell release an official gingerbread update ?
3. Right now my phone is SIMUnlocked, will I lose my SIMunlockation after the flash ?
4. And is my actual configuration right to excecute this flash or should I flash something else before ?
Click to expand...
Click to collapse
1. yes, it's possible
2. yes, but you would either need to downgrade first or do a kies hack
3. no
4. you can do it straight

Thanks zorxd.
I am going to try. So there is no need for me to select any Pit file or did the guy forget to mention it ? Also can we tick the repartition option in Odin?
Sorry if I ask usekess question I am used to flash android but new to the SGS flashing...

when you repartition you need a PIT file.
My advice is to not repartition unless you need it.

Too late... I did it got stuck into bootloop. I had an error when I tried to install the zip from the recovery (I had recovery 3e) : E : Short write of /tmp/sideload/package.zip (No space left on device) . However, I flashed the back eclair JHL and went back to the stock eclair rom. I am going to restart from there following your intructions. I now have recovery 2e ( Somehow I can't get ClockWorkMod Recovery to load directly; it always send me to recovery 2e and there I apply update.zip to go to CWM recovery)
Thanks for your help, I'll let you know if I manage to get it done.

Still get the error E:Short write of/tmp/sideload/package.zip (No space left on device) when try to install JVH_KC1_BMC.zip from the recovery 3e ( this recovery comes right after I flash SpeedmodK15E_withLoaders.tar ...
Don't know what else to try... Help please..

I did it a slightly different way. From 2.2, I flashed a stock 3 part gingerbread rom (phone, PDA, CSC) with bootloader update using ODIN 1.82. I then flashed CF root gingerbread kernel for CWM3 and then flashed the KC1 modem from clockwork recovery for the 850 band.

Could you please show me the exact files you used so I can try to do the same ?

Aren't there at least a couple threads on how to install jvh/jvp on an i9000? Its the exact same process as those you just have to flash the kc1 modem via cwm after you are done. It sounds like you guys are experimenting too much.
Sent from my Darky's i9000m

nguetto said:
Could you please show me the exact files you used so I can try to do the same ?
Click to expand...
Click to collapse
Our canadian phone is not really different from all the other ones, so you don't need a special "Bell Canada" installation.
If you want JVH, you can follow this thread:
http://forum.xda-developers.com/showthread.php?t=818556
You don't have to do everything like fugumod, etc. I would flash JVH via odin and then flash CF root kernel via odin so you get CWM3.
There's also leaked 2.3.4 JVP gingerbread out, if you feel inclined:
http://forum.xda-developers.com/showthread.php?t=1102881
There's a way to enable 850 band on the different gingerbread modems, but i never bothered, I just flashed the KC1 modem for Bell which has the band (via CWM3). Search for I9000UGKC1
http://forum.xda-developers.com/showpost.php?p=9874879&postcount=1

Okay I am really starting to freak out now...
I am stuck in bootloop, I can't get out og it. I tried flash Back the Stock Bell Firmware but it keeps boot looping. Download mode is okay. But it started doing this I had a message like sd could not be mounted in recovery 3e. Now I can't even access recovery after I flash Eclair but Download mode is still okay...
Aby ideas ?

Have you tried flashing back the stock JL2 firmware from bell? (found on samfirmware.com)
I've never encountered this error before, I wonder if it is a problem with the bootloaders, as the official froyo firmware from bell had a secondary bootloader and gingerbread has its own bootloaders as well.

nguetto said:
Okay I am really starting to freak out now...
I am stuck in bootloop, I can't get out og it. I tried flash Back the Stock Bell Firmware but it keeps boot looping. Download mode is okay. But it started doing this I had a message like sd could not be mounted in recovery 3e. Now I can't even access recovery after I flash Eclair but Download mode is still okay...
Aby ideas ?
Click to expand...
Click to collapse
I imagine you'll need the stock bell firmware as said above and also the proper PIT file to go along with it.
Sent from my Darky's i9000m

Also if you repartitioned it when you tried to flash the whatever it was when you tried you will also have to repartition it when going back down to froyo.
2.2 and 2.3 use different bootloaders therefore if you try to mix and match rom's without the bootloaders and repartioning you will get a ****y phone.
Sent from my Darky's i9000m

Thanks for your help guys. I didn't solve it yet, but i will open a new thread to prevent this one from getting to messy.

cm9 via odin3

hey guys, my samsung is in a bootloop and recovery mode is not acceseble
im looking for a cm9 firmware thati can flash via odin3 to fix my phone

i think that is not possible .start ur fone in download mode .flash a stock rom .and then flash CM9 .

Just search for "fix recovery" package. I've seen it in many threads. It should help you
edit: here..I came across with this in some thread..
http://ics.samsung-updates.com/trouble/FixRecovery.tar.md5
Sent from my GT-I9000 using Tapatalk 2

if you manage to get into recovery, try to flash cm9 again, it will probably fix your problem.
if you rather flash JVU to start over again, dont forget for the small installation that comes after the odin process to end before flashing any custom kernel.

(Q) (Solved) Problems with upgrading and rebooting

Hi guys. First of all it's gonna be my first thread. That's way I wanna say hello to everyone. Anyway. I just tried to upgrade my Samsung Galaxy S Gt-I9000 to ICS 4.0 and I followed pinappu. hubpages. com/hub/Samsung-Galaxy-S-firmware-update-to-Android-40-aka-Ice-Cream-Sandwich instructions. My phone installed the upgrading files successfully. After rebooting my phone didn't turn on. I can't start my phone even in recovery mode but download mode is working. What should I do?
Yours
Sir_Night
---
Sorry for my lexical and grammatical errors. English isn't my native language.

Boot into download and flash a GB rom through Odin. Then flash a kernel with CWM (like Semaphore). Download any ICS rom zip file and flash it twice (it will bootloop or reboot recovery after the first flash).
The instructions and links to tutorials/videos for installing roms are usually in the rom's OP so you can just follow that.

Captain_17 said:
Boot into download and flash a GB rom through Odin. Then flash a kernel with CWM (like Semaphore). Download any ICS rom zip file and flash it twice (it will bootloop or reboot recovery after the first flash).
The instructions and links to tutorials/videos for installing roms are usually in the rom's OP so you can just follow that.
Click to expand...
Click to collapse
Thank you for your reply. I just flashed GB 2.3.6 rom and now my phone is working. Thank you. I'm not sure about ICS anymore

If you only want the appearance of ICS use SauROM and then flash the ICS theme. It looks just like ICS but is obviously still GB.

When bootloop or no CWM occurs after flashing from GB -> ICS:
-remove battery
-download a ICS kernel to your PC.
eg. Semaphore ICS http://forum.xda-developers.com/showthread.php?p=21910951
-start Odin and put .tar in PDA field. Untick repartition.
-insert battery and go download mode.
-connect usb to PC and flash ICS kernel.
Next boot of phone should be normal ICS.

How to restore back to stock kernel in galaxy y ? :( please help :( ?

i installed merruk technology kernel pre 2.0 final ... and now want to restore back to default kernel(stock) .. i have ddle1 stock rom running....
i tried restoring to stock kernel provided there on merruk kernels page but the kernel wont remove help me please
if i could get boot.img from ddle1 rom i would be greatful ...
or can someone tell me how to extract it from .md5 flashable rom i have ( through odin )
and when i try to flash a stock rom (ddle1 for instance ) through odin it shows this error.. the picture is attached below

chotu222 said:
i installed merruk technology kernel pre 2.0 final ... and now want to restore back to default kernel(stock) .. i have ddle1 stock rom running....
i tried restoring to stock kernel provided there on merruk kernels page but the kernel wont remove help me please
if i could get boot.img from ddle1 rom i would be greatful ...
or can someone tell me how to extract it from .md5 flashable rom i have ( through odin )
and when i try to flash a stock rom (ddle1 for instance ) through odin it shows this error.. the picture is attached below
Click to expand...
Click to collapse
You have to select Modem and CSC files too I guess

avinash9441 said:
You have to select Modem and CSC files too I guess
Click to expand...
Click to collapse
I tried with MODEM and CSC also i got FAIL !!!!! at top left box :crying::crying::crying:
here plz help

you sure you picked all 3 files? shud be ok by then .
Sent from my GT-S5360 using xda app-developers app

chotu222 said:
I tried with MODEM and CSC also i got FAIL !!!!! at top left box :crying::crying::crying:
here plz help
Click to expand...
Click to collapse
Download and flash through odin DDLC2_ODDLA2_DDLC2 or DDLE1_DDLD1_DDLE1. Even I had problem with DDLA3_DDLA2_DDLA2.
Hope it works now.

hmmm
Im really confused, because if you flashed merruk kernel and it did not work then just download recovery kernel..
put phone in download mode (power+home+volume down)
plug phone to pc while odin is open
choose recovery kernel on PDA option (don't check or uncheck anything)
flash it and it should work... lol
Stock : http://www.mediafire.com/?dzfcrhb8fj3s40x
Terma Kernel ; http://www.mediafire.com/?81d1acx1c19m9k5
Test Kernel ; http://www.mediafire.com/?0j6guwgg60opj7y
-----------------------------
iplaygalaxyy for android

chotu222 said:
i installed merruk technology kernel pre 2.0 final ... and now want to restore back to default kernel(stock) .. i have ddle1 stock rom running....
i tried restoring to stock kernel provided there on merruk kernels page but the kernel wont remove help me please
if i could get boot.img from ddle1 rom i would be greatful ...
or can someone tell me how to extract it from .md5 flashable rom i have ( through odin )
and when i try to flash a stock rom (ddle1 for instance ) through odin it shows this error.. the picture is attached below
Click to expand...
Click to collapse
It was happened to me before.. I have no choice but to flash to a fresh STOCK ROM with stock Kernel.
The SOLUTION would be ODIN. Go to Doky's thread and select the latest version of your firmware based on your country - download and extract.
Here's his thread : http://forum.xda-developers.com/showthread.php?t=1465800
Now, download ODIN if you're not having it yet. here's the thread - credits to OP : http://forum.xda-developers.com/showthread.php?t=1464775
Here's the instruction on how to flash to STOCK ROM and Kernel. http://forum.xda-developers.com/showpost.php?p=21846668&postcount=2
I did formatted my sd card extent that time too hope it helps.

anyone can help

Restore to Stock Kernel
Download the stock kernel ...
In Odin choose PDA and select the kernel
Flash it in Download Mode....

guys
i can only give you my solution....i was on hells kernel #50 and i wanted to revert to stock.....
i tried DOKY73 sirs stock roms but they didnt work.
thus, my and my friend YASH 98 modded it and now it works perfectly....
simply use these instead of the stock on DOKY73s thread.
http://d-h.st/tjd
[ Tested ] [ worked when sir dokys failed ]

how to remove meruuk kernel from g s5360[[[[[[samsung glaxy y]]]]]]]]
my build is GINGERBREAD.DDLF2
BASEBAND version isS5360DDLF1
KERNEL IS 2.6.35.7 Merruk [email protected]
I want to revert back to my stock kernel.please tell me how to do this.
I can't update my phone because of it.

Flash stock rom via odin. U can get all the requirements at sir doky73's thread.
What u need :
1. Odin
2. Your own country's firmware and totoro_0623.pit ( find it on the web. )
3. Usb drivers
4. A pc
5. Samsung usb cable
Extract the zip file u downloaded of your country's firmware. Open the odin.exe on your pc (windows ), then pit option choose totoro.pit, boot option choose boot, phone choose modem file, pda choose pda.
Finished press volume down + home button + power button to download mode on samsung galaxy y. Then screen turns on press volume up again. Connect the usb cable to your phone to pc.
Then odin recognises your phone and shows a yellow thing on the top. Then press start and wait for it to boot up !
Remember to press thanks ya !
Sent from my GT-S5360 using xda app-developers app

That ,or you can flash stock kernel via flashable zip. I remember seeing one in hells fusion thread.

A_Reloaded said:
That ,or you can flash stock kernel via flashable zip. I remember seeing one in hells fusion thread.
Click to expand...
Click to collapse
from where can i get a flashable zip of stock kernel??????

Idk. Search...
Try to get a boot.img of stock kernel.
Then search for Sgybicwm.zip in general section. Put the stock boot.img in root of your sdcard and flash sgybicwm.zip via cwm. You are done.
Any other boot.img flasher like faqbly wont work. I just tried it with hells fusion 50. it has a stock kernels boot.img inside stock folder of the kernels zip. Get that and sgybicwm.zip

[Bruce Wayne] said:
Idk. Search...
Try to get a boot.img of stock kernel.
Then search for Sgybicwm.zip in general section. Put the stock boot.img in root of your sdcard and flash sgybicwm.zip via cwm. You are done.
Any other boot.img flasher like faqbly wont work. I just tried it with hells fusion 50. it has a stock kernels boot.img inside stock folder of the kernels zip. Get that and sgybicwm.zip
Click to expand...
Click to collapse
PLEASE HELP ME. I TRIED TO INSTALL STOCK KENEL BY APPLYING ZIP IN CLOCKORKMOD.
THE SITE WAS GALAXY4GAMING.COM. IT TOLD ME TO WIPE DATA AND CACHE AND THEN INSTAAL ZIP. I DO THAT.IT SAYS INSTALLATION IS ABORTED. I GET BORED AND REBOOT MY PHONE. WHEN I REBOOT IT ,,IT ONLY SHOWS A BLOCK ELCOME SCREEN WIH GALAXY Y WRITTEN ON IT AND DOES NOT DO ANYHING.IT SHOWS IT FOR HOURS AND HOURS.PLESE HELP AND TELL ME WHAT TO DO.:crying::crying::crying:

YES He is right this is a good method of flashing the stock kernel instead of flashing the whole firmware again.
GT S5360
Rom - Jelly Blast v4.0.5
Kernel - Marroc v2.0 Final
Overclocked - 1.2 GHz
Undervolted - -100 mV
Battery - 3200 mAh
SD Card - 32 GB class 10
Swap - 256 MB
SD / EXT - 2 GB ext 3

apoorva.97 said:
PLEASE HELP ME. I TRIED TO INSTALL STOCK KENEL BY APPLYING ZIP IN CLOCKORKMOD.
THE SITE WAS GALAXY4GAMING.COM. IT TOLD ME TO WIPE DATA AND CACHE AND THEN INSTAAL ZIP. I DO THAT.IT SAYS INSTALLATION IS ABORTED. I GET BORED AND REBOOT MY PHONE. WHEN I REBOOT IT ,,IT ONLY SHOWS A BLOCK ELCOME SCREEN WIH GALAXY Y WRITTEN ON IT AND DOES NOT DO ANYHING.IT SHOWS IT FOR HOURS AND HOURS.PLESE HELP AND TELL ME WHAT TO DO.:crying::crying::crying:
Click to expand...
Click to collapse
Stop using all caps mate.
Keep kalm and use odin.
Can you go to recovery mode?
And download mode?
Try to give as much info as you can. So that people here can assist you better.

[Bruce Wayne] said:
Stop using all caps mate.
Keep kalm and use odin.
Can you go to recovery mode?
And download mode?
Try to give as much info as you can. So that people here can assist you better.
Click to expand...
Click to collapse
i dont know what is download mode. i cant go in recovery mode too. its my fisrtt mobile.only passed 3 months with it . o god i am crying:crying::crying::crying::crying::crying::crying:

Ok.
Here is what you need to do.
Download a stock rom from dock73's thread from dev section (its a sticky one, so no trouble in finding it).
Then download odin3 v1.85 from same thread.
Get samsung mobile device drivers.
Install drivers first.
Then extract all those zips (rom and odin ) in a separate folder.
Open odin.exe.
Then switch off your phone (pull battery if nothing works).
Press Volume down + Power + Home Buttons All at same time
You will be I'm download mode.
Press volume up and connect your phone to pc with data cable.
You will see a yellow signal on odin screen. Dont change anything and just add those files from the firmwares you extracted in the folder.
Csc.tar.md5 for csc
Modem.tar.md5 for phone
And
pda.tar.md5 for pda
Click on start and it will show a pass to you when completed.
Hope that complets all for you.
If you still dont get head over to docky thread.
And see 2nd post.