Hello, I itried to install a rom not suitable fot T-mous and I can't recover the phone since Then. It's possible to help me out? I became really sad without my hd2.
I tried to install several different roms (official and others), everything seems fine but when it reboots goes to the white screen and reboots...when i enter bootloader shows:
PB81120 ss-b3
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Still charges through usb and the led is working but when i disconnect it from the pc..Turns off instantly
PLLLLSSSS Help me out through this issue
a plus point of it, ITS NOT BRICKED
DONT DO **** TILL PEOPLE SAY WHAT 2DO..
otherwise you will brick it...(trust me selfexperience, bricked my)
when its bricked, you cant do ****, the phone doesnt turn on, NOTHING happends.
just w8 till some nice people who have some experience want to help you (and me stuck with spl-3.03.0000)
So dont do anything yet!!
Firstly try switching on the phone without the SD Card installed.
If that doesn't solve your problem then:
Go to HTC's website and download a TMOUS ROM (preferably the 2.10 ROM) - you need to use your phone's serial number to get to download the ROM. If you get an invalid message, then you are trying to download a ROM not suitable fro your phone.
Press and hold the Volume Down button then tap the Power button. You are now in Bootloader Mode. Connect to the PC and the 'Serial' at the bottom of the screen will change to 'USB'.
Run the ROM. Just tick the box about ActiveSync.
If in future you are going to run a custom ROM, then check that it is suitable for a TMOUS. Only flash RADIOs with a .50 in it and above 2.07.50.
None of the suggestions...worked...Tried to boot without tha sd inserted...Noresult...And I have installed the two official versions of the T-mobile again with no result )):
Any other suggestions///????
Thanks ):
Sounds like quite a predicament. Have you tried any of the NAND android roms? Maybe a different os might get the phone to act differently.
I'm not going to say that this will work, but if it doesn't you should be able to hard reset back to a windows mobile os you have used previously by doing what you have done up until now with flashing them back on afterwards, putting you back to your current situation.
do a task 29. and try reflashing. (google "mtty for hd2" to perform task 29 )
I have Tmobile as my carrier but ever since I changed my Rom i have a problem with the phone calls breaking up. Either i cant hear what they saying or most of the time they cant hear what I am saying. Ive changed the Rom a few times thinking that is the problem but seems to carry on, no matter what Rom i have. If anyone could help me with this problem would be great.
OMG try a different radio! If you don't know how to flash a radio then go and... what?
If it still doesn't work maybe you're in a bad area!
Ok so its a radio problem, which radio is the best to install and how do i reinstall a radio. On my phone right now - MAGLDR 1.13 Radio is SPL-2.08.HSPL 8G XE CotullaHSPL I've also got ClockworkMod v1.3 installed. A step by step info would be great. Sorry im a noob =(.... been trying to read up.
here is a radio thread http://forum.xda-developers.com/showthread.php?t=611787 and heres another talking about TMOUS HD2 USA 1024 forum.xda-developers.com/showthread.php?t=669733 give it some reading, most people are saying that Leo_RADIO_2.15.50.14** is working best. i am using that radio and its just fine for me.
now how to install, power off your phone, while holding the volume down button power on phone and keep holding volume button, you should be at a tricolor (bootloader) screen, plug in your usb cord and flash your new radio just like you did with HSPL 2.08 and MAGLDR by running the CustomRUU.exe file with the radio of your choice. make sure you dont flash a radio with the number *.**. 51.** in it or you can brick your phone.
Hi everyone! After checking the forum on possible quirks that can be encountered when installing MAGLDR I hope someone can help me with the following:
I am trying to install Android on the HD2 via full-NAND-flash (i.e. directly via USB without SD card). I read tons of webpages and I believe I understood the necessary steps. Check the SPL; Install Hspl; Install MAGLDR; etc.
I tried to install MAGLDR 1.13 and everything went nice and quick: 100% complete on the phone; 100% complete on the PC; click on finish; phone reboot .......... and now the HD2 does not go past the green-on-white HTC splash screen. No boot.
I can still acess the colour-striped bootloader, which reacts if I connect the USB cable. No more.
What have I done wrong? Can it be recovered?
Thanks in advance for any suggestion.
You need to do a bit more reading (it's fundamental). Flashing MAGLDR is only the first step in getting Android on NAND. Next, you'll need to flash CWM and if you're going to install Android, you are going to have to have an SD card.
It's clear you read enough to get as far as you have. I suggest doing a bit more.
Start here:
http://forum.xda-developers.com/showthread.php?t=905841
Thanks but I don't think I can do much more at this point. The phone seems to be stuck (see my initial post). Cheers,
Did you try holding the Red power button down while the phone was powering up? That should take you into the Magldr menu.
Also, since you say you can get into the bootloader, have you tried reflashing Magldr?
Yes, I did. However, in the flash window, where you should see you are going from ROM version X to ROM version Y, this information does not show. The flash process seems to go through normally but then the situation is the same one.
The bootloader I can access is the normal one, with the red-green-blue stripes: it shows:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
On the bottom it reads "serial" and if I connect the USB cable it changes to "USB".
Do a task 29.
Flash radio 2.15
reflash magldr
Hope this helps
yz.hd said:
Flash radio 2.15
Click to expand...
Click to collapse
I think this is the case sensitive for the OP explained symptoms.
Flash 2.15 or any Radio Rom that supports 576MB.
I have used Task29+radio 2.15.50.14, the doloop file repackaged by shadrac.....
So in principle the radio should be the correct one.
Shall I try with the separate flashes? Would you please let me have the links to download them?
(beginning to despair.....)
Thanks
Use HD2 Toolkit to re-flash MAGLDR 1.13... easiest and most comprehensive tools.. If u still stuck, re-install WM ROM (better custom ROM since u want to install AD NAND) this w keep ur HSPL. Once u are back to WM, repeat the whole cycle use the kit (pls confirm ur Radio 2.xx.50.xx (above 2.07.50.xx) and not the .51.
gd luck
Norton 360 doesn't like the HD2 tkit...
Any idea why Norton 360 discards the download telling me the HD2 Toolkit is a threat? That's odd...... the download link comes from this very site.
Anyone else with the same experience? Cheers!
Hi Guys,
I have been having this really strange Sound problem with my NAND Android on my HD2.
I have had NAND Android running on my HD2 for a long time now and it started right after i flashed WP7 mango and then got rid of it for NAND.
One thing to note is I got rid of the WP7 Mango ( XBmod-Yuki ROM) due to its volume problems, especially the in call and speaker volume was extremly low! and looking at all the threads for that it seems like it is a common issue with that ROM so i decided to go back to NAND Android Which took me about a week to unlock my SD card and reformat it and get NAND Android workin again.
After I got NAND setup i have tried all sorts of different ROM's from the official MIUI, to GOMIUI, to MXZ MIUI, to RUNNYMEDE Sense 3.5, to BLISS Sense 3.5 (All based on their latest versions) and on every single one of them it's the same issue. After the phone starts all my phone sounds stop working randomly and when I increase or decrease the volume i can see the indicator hangs for few seconds and if i keep pressing my phone would just lock and I would have to take the battery out and reboot.
Also when the sounds stop and I get a call my phone locks when I try to answer and com.android.phone forces close and i won't be able to use my phone untill i reboot.
This is a really frustrating issue since I have been using HD2 since it first came out and I would love to continue using it due to its flexibility!.
Any help is Highly appreciated
My HSPL version is
PB81120 SS--B3
SPL-2.08.HSPL 8G XE
CotullaHSPL 0x50
My MAGLDR Version is v1.13
My ClockworkMod recovery v3.0.2.4
nickshel81 said:
Hi Guys,
I have been having this really strange Sound problem with my NAND Android on my HD2.
I have had NAND Android running on my HD2 for a long time now and it started right after i flashed WP7 mango and then got rid of it for NAND.
One thing to note is I got rid of the WP7 Mango ( XBmod-Yuki ROM) due to its volume problems, especially the in call and speaker volume was extremly low! and looking at all the threads for that it seems like it is a common issue with that ROM so i decided to go back to NAND Android Which took me about a week to unlock my SD card and reformat it and get NAND Android workin again.
After I got NAND setup i have tried all sorts of different ROM's from the official MIUI, to GOMIUI, to MXZ MIUI, to RUNNYMEDE Sense 3.5, to BLISS Sense 3.5 (All based on their latest versions) and on every single one of them it's the same issue. After the phone starts all my phone sounds stop working randomly and when I increase or decrease the volume i can see the indicator hangs for few seconds and if i keep pressing my phone would just lock and I would have to take the battery out and reboot.
Also when the sounds stop and I get a call my phone locks when I try to answer and com.android.phone forces close and i won't be able to use my phone untill i reboot.
This is a really frustrating issue since I have been using HD2 since it first came out and I would love to continue using it due to its flexibility!.
Any help is Highly appreciated
My HSPL version is
PB81120 SS--B3
SPL-2.08.HSPL 8G XE
CotullaHSPL 0x50
My MAGLDR Version is v1.13
My ClockworkMod recovery v3.0.2.4
Click to expand...
Click to collapse
I suggest u start from scratch..
Task 29
Reflash the radio 2.15.50
reflash Magldr
reflash Clockwork (i run the new 5.0.23 Recovery) Im attaching it if you'd like
and try new roms....
hope this helps
casemandan said:
I suggest u start from scratch..
Task 29
Reflash the radio 2.15.50
reflash Magldr
reflash Clockwork (i run the new 5.0.23 Recovery) Im attaching it if you'd like
and try new roms....
hope this helps
Click to expand...
Click to collapse
Thanks Casemandan for the suggestions.
I have actually re-flashed to the latest radio 2.15.50.14
and re-flashed magldr to 1.13 and HSPL2.8HSPL
and so far the sound has been stable.
I am guessing it was the radio and maybe i had a faulty one before!
Anyways thanks again.
Hi everyone!
I am very sorry for such a n00b-post, but I really cannot find a solution.
The problem:
I recently got a HD2 of a friends who did not use it anymore, because Android suddently stopped working. Now it's stuck at a black screen [A] saying:
aMAGLDR V1.13
Build: Feb 1 2011 03:46:07
by Cotulla 2011
I tried resetting the phone using the red button near the battery, but it did not solve the problem. I am able to boot the HD2 into recovery-mode (colory screen) but then, after connecting to a pc it does not change from "serial" to "usb".
I have installed WMDC on my W7 64-bit system. I have also tried to use "RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship" (from the 4shared "shipped LEO roms"), but none of them recognises my HD2 neither in Recovery nor in the black screen [A].
Is this phone useless? What can I try to revive it?
What might be helpfull: when normally booting, the phone vibrates once during the HTC-screen and 5 times after the black screen [A] appears.
andrejazzz said:
The problem:
Android suddently stopped working. Now it's stuck at a black screen [A] saying:
aMAGLDR V1.13
Build: Feb 1 2011 03:46:07
by Cotulla 2011
I am able to boot the HD2 into recovery-mode (colory screen) but then, after connecting to a pc it does not change from "serial" to "usb".
I have installed WMDC on my W7 64-bit system. I have also tried to use "RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship" (from the 4shared "shipped LEO roms"), but none of them recognises my HD2 neither in Recovery nor in the black screen [A].
What might be helpfull: when normally booting, the phone vibrates once during the HTC-screen and 5 times after the black screen [A] appears.
Click to expand...
Click to collapse
Since you're unable to connect to PC, then you can't re-flash HSPL.
HSPL needed to force flash any shipped WM6.5 ROMs to HD2.
Then the only way is to flash original WM6.5 ROM for your device from uSD.
If you're not sure what CID, just download any HD2 shipped ROMs and try to flash from uSD.
Just be careful not to flash EU's ROM on T-Mobile device!
Extract the ".exe" file, then rename the ".nbh" file into "leo.nbh", copy that to root of uSD.
Power up your device while pressing vol down button.
Don't worry if the ROM refuse to flash, it's just a wrong CID.
But to make sure, connect your device to another clean PC (without android drivers inside, just WMDC), preferably a PC sets for syncing WP7/WP8 devices.
And make sure your device turns on by itself when charger is connected (auto turn on from off state).
That's just to make sure that usb connector is not damaged.
HD2 vibrate 1x at power on, it's normal.
Vibrate 5x after magldr shows up, I suspect something wrong with magldr or the ROM itself (corrupted or something).
Another possibility is some NAND bad blocks.
But if it's vibrate 5x at power on, then you have a bad luck.
The point is, flash the original ROM first.
If it's success, then flash HSPL.
After that, the rest is up to you..
Firstly, I want to thank you very much for your quick and extensive answer!
But I have only one tiny question: are these the ROMS which I can find at http: //www . 4shared . com/dir/22189940/b8552fa0/Shipped_Leo_ROMs.html#dir=MGRa1Cen ? And you mean I should just pick one and try?
You can also find HD2 shipped ROMs here.
Anything that has "TMO" are T-mobile ROMs, otherwise it's EU.
Again, don't flash EU's ROM on TMO devices!
The first 3 digit are the ROM version (1.66, 1.48. etc.), 3.14 is the latest WM6.5 ROM.
The next 3 digit are CID code (207, 404, 707, etc.).
Like I've said, if you don't know which CID for your HD2, then just download all ROMs from different CID then flash it one-by-one using uSD.
Thanks!
So far I have tried the 404 and 162 (edit: and 161, 911), but so far without luck. I'll keep you posted!
Tiny question: is it normal that I cannot shutdown in Recovery Mode?
Perhaps some useful info shown in Recovery:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Correct me if I'm wrong, but it looks like an EU HD2, TMO HD2 are rarely using hynix nand, made around late 2009 or early 2010.
Just try to flash ROM with CID for your friend's country first.
If failed, then try another CID.
There should be one or two info about CID number vs. country somewhere around.
Good luck!
Sent from my Windead Phone 7 using xda app-developers app
At this moment I have tried all the NLD roms with no result. Also I have tried roms from several european countries, but none of them works:/ Might it help if I give the serial number?
And what might be worth saying: my phone turns on when connected to AC power / wall-charger; when connected to charger the "serial" disappears...
Thanks for all your help!!!
Have you try connect to other PC?
When flasing ROM from uSD and failed, what error message you got?
If it's "CID mismatch" or something like that, than it's definitely a wrong CID.
If it's "ROM update error bla bla bla", it's most likely corrupted flash image or the uSD itself (use a small sized uSD, 1gb would be fine).
Even if you flash the correct CID, without removing HSPL first, it would still throw an error message "ROM update error bla bla bla" during flashing Radio.
Then it will restart and retry to flash again on it's own.
By the way, I don't know if there are ways to flash HSPL from uSD.
Or guide on how to make a "gold card".
I sugest you search it.
Worth to try if you couldn't find the correct CID for your device.
CID from serial number?
Yes, back in 2010/11 HTC site provides s/n checking for download the correct ROM.
But now it's gone.
Sent from my Windead Phone 7 using xda app-developers app
Thank you very, very much for helping such a newbie ^^
At this moment, I am able to get into the update-menu: I changed the filename to LEOIMG.nbh. The only problem is that all the Dutch images give the same error: 00018003 : Radio (V2) - FAIL.
What could I do to solve this error? Use the freezer-trick or wouldn't it make any sense?
edit: it does boot when I connect to another W7 pc with WMDC (replies " Not connected" ), only it automatically starts the update-procedure (which fails).
There are no such thing as newbie, that's why we need to learn.
Error 00018003 during Radio flash?
I have no idea what error is that.
But first, are you sure that your friend bought the phone on local shop?
I mean, not imported, or when he/she travel overseas, or has the mainboard swapped at HTC service center.
It happens to me when my second HD2 suddenly has no signal, about 2 years ago.
Brought it to local service center and they swapped the mainboard without telling me.
And the swapped mainboard has CID from 404 (europe), the original was 707 (indonesia).
Okay, back to error something.
WMDC won't recognize the phone unless it's a working WM6.5 device, or a working WP7 device with WP7 SDK + Zune installed on your PC.
Just put the phone into bootloader screen (3 color screen), then connect it to a clean PC.
Does the "Serial" changed to "USB"..?
If it does, reflash HSPL 2.08 using HSPL4 package.
Then flash Radio ROM only, 2.15.50.14 is a good one.
Again, an EU HD2 can use either EU's Radio ROM or T-Mobile's Radio ROM.
But a T-Mobile HD2 can only use a T-Mobile's ROM..!
If the "Serial" doesn't change to "USB" but on your PC makes sound like something is plugged in, open device manager and look for an unknown device (no drivers loaded).
Expand it, what does it says?
To be honest: I am not 100% sure that it is an European (Dutch) phone. What I saw when I opened the phone's back was that the warranty-seals on the screws were molested. I don't think he got the motherboard replaced: way to expensive in relation to a new phone...
The bootloader screen gives now the following text:
RUUNBH
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0X05
CotullaHSPL 0x40
Upgrade ROM error
Please try again
When I connected it to a clean pc, the phone booted and gave another upgrade-error, only this time on a black screen (I got the uSD out the phone).
After booting the phone and connecting to a pc the "serial" does not change to "usb"...
When I tried to install WMDC I get the error "Installationpackage not supported by processor". Seems like bullcrap, but there it ends. No yellow exclamation marks in Device Manager...
I have yet not tried to flash a T-Mobile ROM to the phone. I have tried all the NLD ROM's: 1.66.404 ; 1.48.404 ; 1.66.404 ; 3.14.404 ; 1.66.404 ; 1.43.404
I have yet not tried the other ROMs I downloaded, but I will tomorrow. To start 161 does not work.
Also: I cannot shutdown when in bootloader or MAGDLr, is that correct?
What colour are your call & end key buttons !
if white you have standard EU type model. T-Mobile EU models are same as any EU model & can flash any ROM/Radio
If green & red you have a T-Mobile USA model (TMOUS) & need correct ROM (found in HD2 Wiki)
T-Mobile USA model needs care as if flash wrong radio version you can brick it.
Flashing via SD card should be last choice as first stage of a SD card flash is install of the SPL to standard SPL from the nbh which means you have no CID bypass as HSPL gone.
ideally you need a Windows 7 32bit machine with a known working WMDC setup & try flashing a suitable rom once decided on EU or TMOUS device.
As you have HSPL on your HD2 already it will bypass CID if flash via PC so you can flash any CID code rom.
Try connecting device to PC (with known good WMDC) and use reset button on HD2 to boot to bootloader & see if get any luck in running ROM installer from PC.
If lucky the USB flash issue is PC & drivers rather than hardware on HD2.
I would suspect you have nand issues on HD2 or perhaps worse, if nand sometimes you can get it back if persistent & get something to flash completely.
Thanks MisterB for adds up.
So am I, suspected a nand issue.
The reason I want him to revert back to original SPL & Radio is to make sure that it's a nand related problems, not radio hardware problems.
If he managed to find the correct CID for his phone, he could easily reverts back in case somethings wrong in the future after playing with custom ROMs.
This also happens to my friend's phone a couple months ago.
But in her case, the bad blocks are definitely located where magldr resides, and many more on data partition.
She can flash shipped ROMs completely, but it refuses to boot.
Can't flash a WP7 ROM because magldr freezes when it's loading, can't even bring the menu screen.
She can run a native sd android build for a couple weeks, but then it acting strange again.
Then finally she just gave up and bought another phone.
@andrejazzz:
You can't shutdown on bootloader (3 color) screen.
Remove the battery is the only way to shutdown, or press the reset button to restart.
But you can shutdown/restart or anything else on magldr menu screen.
Press & hold power key right when magldr loads up (before it's start to "go go go").
In addition, you can download WMDC x86 version here, and x64 version here..
He may indeed need try SD flash but I would exhaust all options of USB cable flash via PC first as retaining HSPL will be useful to start with as any generic HTC ROM could be used for the USB cable flash.
If that is not possible then flashing via SD is only viable option & indeed many times only way get over bad boot/nand issues but with all the CID versions for HTC regions & operator branded regions you have a hard job knowing the right one, you could even try the right ROM & as it does not flash overlook it for further testing.
I see he has tried SD flashing but still has HSPL so either SD card is not best suited for nbh flashing or nand/hardware that bad even first stage of flash is not possible.
If I was testing this device & trying recovery I would probably try freezer test to cool device prior flashing & make good effort on USB flash before going on to SD card.
Most well used Android HD2s these days have nand or bga issues to some degree as android works the hardware so much harder than WM6.5.
You really need be sure PC & driver are known good for flashing & if going to SD flashing that SD card is suitable or you will waste a lot of time & effort.
Loads of links & tips for all the software & some threads are in the HD2 Wiki
I apologize for replying so late, but I have had no time: I had a few tests at school
@Mister B: I have a black HD2 with white icons, so I have a european model.
I have installed installed the X86 on a clean 32-bit system, but it does not recognize the phone. I have reinstalled the WMDC on my W7 64-bit system, but still it does not recognize the hd2. I have no other Windows Phones, so I am not able to verify the WMDC-installations.
When I connect to a pc, the phone boots and shows: "Software update failed! Please try again"
@Shadow_Nexus: Correct, that is exactly what happens. I do not completely understand what you mean with "Press & hold power key right when magldr loads up (before it's start to "go go go")", could you please explain?
@Mister B: How could I check if the SD-card might be the problem? It is a 16GB Class 4 Kingston SD. I have tried all the NLD-roms and other versions (random countries, not TMOUS). I have tried the freezer trick with a NLD-rom on a mSD, but it did not work.
Thanks for all your help!
Best using a 2gb or 4gb (8gb max) card for nbh flashing & do a proper fat32 format with something like hp format tool before using it.
link below may help:
http://forum.xda-developers.com/showthread.php?t=681317
Again, thank you very much for your reply. But: do you have any clue what ROM's I should try? I am asking this, because I have already tried all the NLD ROM's I found on the site @Shadow_Nexus gave in post #4, but every one of them returns the same error. Should I switch to another country and try, for example, all German ROM's?
I got my hands on another HD2 and when I connect that one to my pc it show up, named "HTC Sync". The bricked one still does not respond:/ Should I retry all the non-TMO roms I can find?
Edit: My brother "helped" me out and sold the phone...