Database Users

phone call audio problem with ameo

I don't know if this is a fault or something I didn't expect but would be glad to here how others have found it.
I have had the ameo for a few weeks and have noticed that if I use a bluetooth or wired headphone everything seems to be fine on a phone call. However when I try to use it as a speakerphone, whoever I am speaking to complains that my voice is breaking up (I have a strong signal strength). It appears that if there is any response from the person I call or any noise in their background then the microphone at my end is interrupted making my voice unintelligible. I know the manual says to use a headset but what is the point of having a speakerphone if you can't use it? Does anyone else have the same problem or have I got a faulty unit?

bobg said:
I don't know if this is a fault or something I didn't expect but would be glad to here how others have found it.
I have had the ameo for a few weeks and have noticed that if I use a bluetooth or wired headphone everything seems to be fine on a phone call. However when I try to use it as a speakerphone, whoever I am speaking to complains that my voice is breaking up (I have a strong signal strength). It appears that if there is any response from the person I call or any noise in their background then the microphone at my end is interrupted making my voice unintelligible. I know the manual says to use a headset but what is the point of having a speakerphone if you can't use it? Does anyone else have the same problem or have I got a faulty unit?
Click to expand...
Click to collapse
I get this on full volume in a small room. Turning the volume down a bit usually seems to solve it. I think the mic is pretty sensitive and can get flooded a bit too easily.

bobg said:
I don't know if this is a fault or something I didn't expect but would be glad to here how others have found it.
I have had the ameo for a few weeks and have noticed that if I use a bluetooth or wired headphone everything seems to be fine on a phone call. However when I try to use it as a speakerphone, whoever I am speaking to complains that my voice is breaking up (I have a strong signal strength). It appears that if there is any response from the person I call or any noise in their background then the microphone at my end is interrupted making my voice unintelligible. I know the manual says to use a headset but what is the point of having a speakerphone if you can't use it? Does anyone else have the same problem or have I got a faulty unit?
Click to expand...
Click to collapse
I have used both the Ameo and the Dopod rom on the same device and can conirm that this problem is worse on the Ameo rom
Could other dopod users tell their experiences regarding hands-free calling

bobg said:
I don't know if this is a fault or something I didn't expect but would be glad to here how others have found it.
I have had the ameo for a few weeks and have noticed that if I use a bluetooth or wired headphone everything seems to be fine on a phone call. However when I try to use it as a speakerphone, whoever I am speaking to complains that my voice is breaking up (I have a strong signal strength). It appears that if there is any response from the person I call or any noise in their background then the microphone at my end is interrupted making my voice unintelligible. I know the manual says to use a headset but what is the point of having a speakerphone if you can't use it? Does anyone else have the same problem or have I got a faulty unit?
Click to expand...
Click to collapse
I experienced something similar but only when the caller has a lot of background noise on their end. It's not a consistent problem here so I assume it's not the same issue you're having.

Thanks for the replies - it looks as if the unit is working to spec but that there is a 'built-in' problem when using the phone as a speakerphone. I didn't get this on the spv2000 I replaced with the ameo so wasn't expecting it. Background noise does seem to trigger it - I just tried phoning using the speaker phone to call an answerphone and it worked fine with clear audio at the other end. I think a day or 2 of playing with the volume to minimise the problem is the next step. I'll post back when I can be more definite but would be grateful for any other opinions.
Cheers
BobG

On my U1000 the mic works fine in speakerphone mode. There are no brakeups of voice even while walking mid-traffic. Yes, I have to speak loud but that is expected with background noise over 85db.
However, the speakers do not return sound very loud at all (for a speakerphone). I have to lean way forward and almost put my face on the screen to be able to clearly hear the other side (even in a totally quiet environment).
Would have been great to have had a decent speaker phone, but as it is I'm sticking to my bluetooth headset.
The 2 drawbacks with bluetooth is the answer delay, it takes a good 1 second before the connection is established between the headset and phone. The second thing is the sensitivity of the mic, it picks up everything that goes on around you, and drowns out your voice. I have to move the mic close to my mouth if there is other noises going on around me (but this is most likely a bluetooth headset problem, and not related to the U1000).

OK several calls later and after fiddling about with the volume I've found that the best way for this problem to be overcome is to set the 'in call' volume to its lowest! I've also set the main unit volume to about 40% but that shouldn't really have any effect. It's odd that the best way for the speakerphone to work is on minimum volume - fine for single calls but not much use if I want a few other people to listen in. However this is a very small problem now and the benefits of this device hugely outweigh this small drawback.

Use in Car through Aux in

hi,
I have been using a Nokia phone with a 3.5 mm audio jack to connect it to my aux-in of the car and listen to music as well as make or take calls. The phone mic picks my voice quite well and I hear back the calling party through the car speakers.
Does the same work with HTC Touch HD too?
Update: I have connected the HTC Touch HD to my car's Aux in and it works well with the THD's mic picking up my voice easily. I had echo on a couple of calls but would like to check for its recurrence to believe that's some problem with unit or with the connectivity.

Afraid not mate.
When you plug something in the earphone socket, it assumes there's a mic plugged in too, like when you plug in a hands-free kit.
I've got exactly the same setup and didn't click what the problem was the first time I took a call. I just sat there like a pratt, shouting "HELLO" at my phone! lol
There may be a software workround for this, but not that I'm aware of.

I use the same approach.. but currently even though I am using a Belkin cable to a pretty neat deck.. the sound is completely off.. Treble is too high.. and My faithful kenwoods which would handle the full Volume of my N95-2 with ease are now cracking up.
Any ideas??

I use the same approach.. but currently even though I am using a Belkin cable to a pretty neat deck.. the sound is completely off.. Treble is too high.. and My faithful kenwoods which would handle the full Volume of my N95-2 with ease are now cracking up.
Any ideas??

Ideally, you should have the phone volume at about 75% of its max (between the phone volume itself, and the volume on the music player application), and control overall volume from the deck. If it still sounds dodgy after that, mess about with the equalizer on whatever player you're using, or the htc audio booster.
If anything, mine's a little quiet, but I've not tried messing with output volume settings in Tweak HD. I tend to have to have my deck turned up about 70-80%, whereas I normally have the radio at about 20-30%.

johncmolyneux said:
Afraid not mate.
There may be a software workround for this, but not that I'm aware of.
Click to expand...
Click to collapse
Asking this question to all. Is anyone aware of any software to use HTC Touch HD mic while using a 3.5 mm headphones through its audio jack.

not both speakers and mic are off when in headset mode
it's a hardware thing
but like with htc headsets you can connect external speakers and mic to the conntors and it works
easy way is to tear the headset apart and solver in the stuff you want to the connector which came with the headset

johncmolyneux said:
Afraid not mate.
When you plug something in the earphone socket, it assumes there's a mic plugged in too, like when you plug in a hands-free kit.
I've got exactly the same setup and didn't click what the problem was the first time I took a call. I just sat there like a pratt, shouting "HELLO" at my phone! lol
There may be a software workround for this, but not that I'm aware of.
Click to expand...
Click to collapse
Mine works fine setup like this. I've got a 3.5m jack coming out and going into the back of my headunit. I can make calls without a problem. The phone seems to realise the connected jack doesn't have a mic so uses the internal one.
The first time I tried it though the person at the other end couldn't hear me but finally worked out this was because the cradle I was using was blocking the mic on the bottom of the phone! I quick readjustment of the cradle and everything was fine.
Sound quality when playing tunes has always been fine but the voice quality aint that great, the person at the other end sometime complains about echo.

crankshaft said:
The phone seems to realise the connected jack doesn't have a mic so uses the internal one.
Click to expand...
Click to collapse
Hmm.... I'll have to have a play with that then, as it was a total failure for me previously. I definitely didn't have the mic blocked, as my cradle holds the phone by the sides.
Cheers for that - I'll have a play about.

How about something like this?
http://www.overstock.com/Electronics/Audio-3.5-mm-Adapter-with-Microphone-for-iPhone/3440143/product.html?cid=133635
(iPhone example but googling "3.5mm microphone output" finds you more, all about £3)

"How about something like this?"
there is not standart for how 3.5mm jacks with mics work as in the width of the ring and such
doubt very very very much that iphone converter would work with anything but an iphone

Thats a good idea. I havent tried this myself but its not experience that the hadware needs an attached mic when plugging the 3.5mm into speakers. I use high quality headphones with no attatched mic to listen to music on the HD and can take calls via the phone or skype by using the headphones and the phone mic.

crankshaft said:
Mine works fine setup like this.
Sound quality when playing tunes has always been fine but the voice quality aint that great, the person at the other end sometime complains about echo.
Click to expand...
Click to collapse
Same setup as me for the last 12 months. I have to play around with the volume setting on the HU / HD all the time - its not ideal but the internal mic seems to pick up voice fine (and echo!).

[Q] Phone call quality on headset

Does anyone actually use the phone as a phone? I'm finding that the echo cancel really limits the quality of the phone. I can hardly carry on a decent conversation in the car using the supplied headset.
Does anyone else have this problem?
Try this: connect the headset. Call your phone from another phone. Listen to both at the same time. You can clearly hear when you talk that the phone is suppressing noise.
What I find is that when I'm in the car, it actually seems to suppress the volume of the person on the other end! So, it can be very frustrating as I miss words that they say.
Combine this with AT&T's marvelous AGC (where if you don't talk, it cranks the volume so that when you do talk, it blows the person on the other end away!), and the total quality of the call is horrible.
I've been using cell phones for almost 20 years. This is the worst phone quality I've ever experience.

When I use the phone directly for calls, everything sounds clear and at a consistent volume with one exception, while waiting for the other party to answer, the call ringing tone goes up and down in volume.
I've paired 3 different bluetooth headsets to the phone and found that the volume in my headset goes up and down quite a bit. Usually it's the worst at the beginning of the call. Sometimes I can't hear the other person answer but then it levels out a bit and the volume fluctuations are less extreme. I've tried an old Sony Ericsson, a Jabra Extreme, and have settled on a Plantronics Voyager Pro+. The Voyager is about the best I've tried but still exhibits the volume fluctuations but not as bad. It also supports A2DP so I can listen to podcasts through the headset.

I use it with the Sync system in my ford f150 and have no problems at all. It works great. I dont use headsets so..........only my sync system

I thought it was just me. My Plantronics 925 does this as well. Calls from the phone are fine, but the headset volume cuts in and out. Is this a bad Bluetooth stack or other problem? I think I remember another phone (WM 6.5) that had to get hacked to fix this. I'm a little miffed on this. Did anyone at Samsung or ATT test the bluetooth on this phone before selling it?

I have had very good call quality whether using the "phone as a phone", the phones speaker phone, or a blue ant bluetooth headset. I have had poor call quality only when trying to call someone in very low signal area. That has only been once. Otherwise overall clarity and volume have not been an issue, actually phone volume on high is too loud for my ears!

adding to my earlier post. I exchanged my Focus due to an unrelated issue. Both handsets had the same fade out issue with the bluetooth headsets. I've experienced it on every call so I don't think it's signal related. I don't see any volume fluctuation at all when using the handset without the bluetooth headset. I've tried the same three bluetooth headsets on my wife's iPhone 3GS and all work fine. I've also streamed at least a couple of hours of podcasts from the Focus to my headset and the volume is perfectly level. Whatever the issue, it's only related to phone calls. Very frustrating.

I've experienced the same issues. I have an Aliph Jawbone Icon. Before I updated the firmware on it I could barely hear someone on the other end. With the new jawbone firmware I have the ability to control the volume in the headset and only when I have it turned all the way up does it work ok. I do, however, still have trouble when people are talking that when the first start and or finish talking what they say seems to get clipped. Further, the volume seems to fade in and out. Also, if I'm using the AT&T navigator software and have my headset attached it will give me directions through the headset, but the end of every direction gets chopped off. So, the avene or street part of a direction doesn't come through.

I've been following this issue in a few different forums. Today a moderator in the Microsoft Answers forum jumped in and said they were experiencing the same problem and they would escalate the issue.
http://social.answers.microsoft.com...4ce-30ee-4734-9dab-28ce0d561132?prof=required

Can't recommend this phone
I was so excited when I first got my Focus. I thought it was such a huge step forward for MS mobile and actually had some chance at being mainstream. Sure it lacked a few features but there was the hope that MS would update the phone quickly. After all, they seemed to have made such phenomenal progress in getting the phone to market, seemed like fixing a few things and adding a few features would be a no-brainer.
Well, here we are 3 months later (Apple released the first update for iPhone 1.0.1 only one month later) and lots of rumors but nothing substantial on the long-awaited update. We'll see cut/paste but it's not at all clear if they will address anything else.
Here in CA we have a law that says we can't talk on the phone unless it's hands free. For the first time since that law was imposed, I've been regularly breaking it. I can't use a handsfree headset. Even the wired one that comes with the phone is so damn inconvenient that by the time I get it going, the caller is long gone. So, seemingly MAJOR features like BT headsets appear to get no notice at all from MS. I've looked through all the threads and there's nothing from MS. They don't even acknowledge the problem.
Looking at the thread from mcraine, I don't see where MS is going to do anything about this. Also, don't see any indication that it's part of any forthcoming updates.
Too bad. I thought this MS had a chance with this phone but they are blowing it big time. Momentum is gone now. If we have to wait another 3 months to get the browser fixed then the phone is destined to be like the Palm Pre. Good phone but can't keep up with the 'big' boys. This horse jumped out of the gate and was looking really good for the first couple of strides but then completely fell down and they are trying to coax it to get up again.

same issue here as well. mine is only a month old. it is not as noticable when sync'd to the car, but still noticable. and as said before more at the beginning of the call. if there were not issues, it would not be M$

[Q] Has the focus audio volume issues been sorted out yet?

Tried to ask in another thread but it was kinda off topic.
Last I knew people were playing with diagnostic codes but there was no consensus on what did or did not work.
Audio from the headphone jack and seemly the blue tooth was too quiet.
Is this still an issue?

Is that a no?

In all truth, i don't use the bluetooth. But i just checked my headphones, and they sound OK. My sony earphones work great on the phone. I did d/l that one app... Media Volume Settings and set the volume all the way to 100...that may be what is making mine work better. Hope this helps!

haven't tried Bluetooth...
But when i tried headphones it was waay to loud even at 1.
I don't know how to lower the volume using codes.

You should look through the diagnostics codes thread. It has some stuff about sound changes in there as well as some of the registry tweaks you should look up if you're unhappy enough with it to need to change something.

Funkadube: I did and couldn't seem to get any reliable change. Plus having to redo it everytime I restarted the phone seemed crazy.
I know when I had mine the volume level out of the head phone port was NOT loud enough when hooked to my car radio even though every other phone I've ever had was. You'd have to goto MAX VOLUME to get it very loud and if it was a quiet song or something not at loud (I'm staring at YOU SLACKER RADIO) then you could barely get it listenable.
I then installed Bluetooth module into the car and had the same issue with it also.
I'd wish I knew someone with one I could test IRL to see if its still a problem. I'd love to switch back to WP7...

Is there a way to boost the out-of-call Bluetooth volume on the Samsung Focus? Between builds 7712 and 7720, the Bluetooth volume for voice dial responses, TellMe, and text-to-speech were drastically reduced and now they are so low that I can't hear them with the phone turned all the way up to 30/30. I used to use the phone at 20/30 with my car's Bluetooth without a problem on 7712 and 7390. Has anyone else noticed this change since upgrading to 7720?

I didn't see other people complaining about the volume in the accessories thread.
I also have a bt headset and works fine for me.

EnderPsp said:
I didn't see other people complaining about the volume in the accessories thread.
I also have a bt headset and works fine for me.
Click to expand...
Click to collapse
I have a Bluetooth headset and it isn't as bad with the headset. But the text-to-speech is still significantly lower than call volume. In fact, the real issue is that there's a huge imbalance between the out-of-call volume and in-call volume with Bluetooth headsets in 7720.
As I mentioned before, when the phone is paired to the car I can turn the phone up to 30/30 from 20/30, but I still have to boost the volume from the car side about 5 levels higher when I'm out-of-a-call to get any decent level of audio out of the phone. The problem then is that when I take a call it is way too loud and I have to rush to turn down the volume on the car side. It makes the use of the feature so inconvenient that I've just turned it off. While I would be perfectly content with Microsoft returning volume levels to what they were since 7004, I'd just as readily use the Samsung Diagnostic app to make the adjustment myself, if it is possible. I'm looking for any remedy at this point.
Text-to-speech was the feature I was looking forward to the most in Mango, and now it's the only feature of the OS I can't use. I can't express how frustrated and disappointed I am that this has happened, and I just can't understand why this change was made. I've seen no reports of anyone ever complaining that the volume was too loud before 7720. It's one thing if I was seeking a feature that wasn't implemented, but it is implemented and it's broken. I just wish there was some solution or recourse to make it usable again.

Bluetooth and Volume Control

I am having an issue with Bluetooth, crackling, and the volume controls not working. It happened before I unlocked and rooted and thought it might be an area I was going through. However, today I was driving down the road and received a business call. The caller's voice kept crackling and popping like crazy. It would start, stop then start again. I will have to say it was driving me nuts and really hurt my ears. My G2 had no issues like this. This is going through my stereo in my truck.
The phone was sitting in a generic holder attached through a suction cup on my windshield. I tried to turn the volume down on the phone and nothing happened. I tried turning it up and nothing happened. It seems there is no control with the volume rockers. Has anyone else had this issue? I really want this phone to work out as I ordered all my phone and accessories through Amazon at the same time. This will be a real deal breaker for me if it can't be fixed as I use Bluetooth exclusively when I am on the road.

Update: I turned the bluetooth off and back on then went for a ride and talked with my wife. It only popped and cracked 1 time. The volume control still would not work. I had to do all the controlling through my stereo. The volume control works when playing music through my Bose Soundlink but not when connected in my vehicle. That seems rather strange.

Volume control doesn't work with all Bluetooth devices from what ive discovered. I have not had issues with popping to my beats Bluetooth headphones and volume control works

razor237 said:
Volume control doesn't work with all Bluetooth devices from what ive discovered. I have not had issues with popping to my beats Bluetooth headphones and volume control works
Click to expand...
Click to collapse
I can't say if I ever had to reach for my phones volume control on my lg, however I never had the popping I am getting with this phone. The X seems to have some temperamental issues. I'm just trying to figure out if these issues are correctable with updates or if they are flaws that can't be fixed. I want to make sure I don't have a defective device. I really like many facets of the phone.
Sent from my XT1575 using Tapatalk

I had a 40 minute phone call this morning on Bluetooth today. The other person's voice kept changing volumes. It was like the phone was trying to adjust the volume constantly. I had a little popping when the volume would go to loud but not at lower volumes. Is there anyway to set Bluetooth volumes at one level and leave it? I am rooted so I can modify a file if needed.
Sent from my XT1575 using Tapatalk