Hi,
Since I bought HTC Trophy I am trying to find how to use TomTom or IGo,
Is there anyway to do that ?
Thanks
Nope. But you can try this one.
http://forum.xda-developers.com/showthread.php?t=919612
Thanks
I have tried many times to unlock the phone, but no luck
Will wait for a reliable unlock solution
DominikZ said:
Nope. But you can try this one.
http://forum.xda-developers.com/showthread.php?t=919612
Click to expand...
Click to collapse
Unlock works just fine. You only have to reunlock it every time you connect it to your computer (which I barely do as I use Wireless Sync).
I would love a TomTom version for WP7...I've been using TomTom for years on my 2002,2003,5.0,6.0, 6.1 and 6.5 WM/PPC devices (yes, I have had PPC devices from 1.0).
I hope Tomtom comes on board for WP7...
:/
As far as I know TomTom oficially said that they are not interested in Windows P 7 for now :/
When I tried and used both TomTom and Navigon for quiet a while, I prefered Navigon. So I'm glad it is Navigon who jumped on WP7 train
navi
I got Sygic Aura on my iPhone and in my opinion this is the best navi.
shoekstra said:
When I tried and used both TomTom and Navigon for quiet a while, I prefered Navigon. So I'm glad it is Navigon who jumped on WP7 train
Click to expand...
Click to collapse
With a WP7 interface, it might have to do... I will admit I tried both before and I liked TomTom better but, that's just me.
RobertPOL said:
I got Sygic Aura on my iPhone and in my opinion this is the best navi.
Click to expand...
Click to collapse
No offence but, how does that help someone with a Windows Phone 7 model ?
Not quite
DominikZ said:
Unlock works just fine. You only have to reunlock it every time you connect it to your computer (which I barely do as I use Wireless Sync).
Click to expand...
Click to collapse
Hi, you do not have to reunlock your phone. Check on xda forums, there is a simple method to prevent relocking of phone, I have just updated to NoDo and my phone, HTC Trophy, is still unlocked and all side loaded apps are still working.
A few simple steps to unlock and keep it that way:
Phase1:
-----------------------------
1. Do not update to NoDo yet.
2. Install windows phone SDK to a windows 7 pc or windows xp sp3 pc and Zune
3. install the reg file on the PC!
4. disable your PIN verification on the phone
5. Disable your screen timout on the phone, put it always on.
6. Send an email to yourself with the chevron's certificate file and open the email on the phone. Tap the attachment with the certificate file, tap again and chose install your phone should say developer certificate installed.
7. connect the phone to your pc, make sure the Relationship in Zune is not Guest (change it by clicking there on Guest and following screen instructions)
7.1 Close any other software on the pc: skype,yahoo, all, let only Zune running.
8.Minimize Zune and open Chevron's Unlocker, click Unlock it should take no more than 2 seconds. To check if everything is ok after unlocking close Chevron's software,and open it again, now the button should say Relock, if it says Relock your phone has been succesfully unlocked and you can proceed to phase 2.
Phase2:
------------------------
1.Get Tom's Xap installer (google it)
2.Install TouchExplorer and HTC Connection Setup
3.Install the unlockit.xap from this forum to make the phone stay unlocked, and after, run it from the applications menu (it should appear at the bottom of the list as XBMOD.Files.Deployer).
4. Using touch explorer copy \My Documents\My Ringtones\CustClear.provxml to \Windows\
5. Run HTC Connection Setup, pres the check button (that "v" mark) and let it finish.
6. You are done
This has worked for me. After applying all these steps you can now update your phone via Zune. If, somehow your phone gets relocked again use this to unlock it:
http://forum.xda-developers.com/showpost.php?p=10793775&postcount=52
Now, we all know that there is no true GPS turn by turn software available yet. But, Navigon has release a version of their navigation software only for T-Mobile users, that's a pain in the a** for others right? Do a search on the google for a patched xap of the navigon software that workes for any SIM provider you have: NAVIGON_MobileNavigator_patched.xap.
Steps to get it work:
1. Download and install the app with Tom's XAP installer.
2. Enable Data Connections on your phone (don't worry, it's smart enough not to use your 3G connection to download any huge data )
3. Open Navigon Select, it will ask you for activation press ok, it will now simply activate using your 3G/EDGE/whatever you have connection, again don't worry it uses almost 2 or 3KB of data for this.
4. Now it will ask you to connect to a WiFi hotspot for it to download it's main data files,it will not work on your 3G connection.
5. Connect to a WiFi hot spot and let it download all the data needed.
6. After it's done you have a fully working GPS software, but only with Germany, Austria, Liechtenstein and Switzerland.
7. To get any maps you want do a google search for navigon maps, mainly for 1.7 version.
Installing maps:::
You either get the maps the normal way or you search for navigon 1.7 iphone maps wich come in an .ipa extension. This you can extract with Uniextract and find the required .map files inside.
OK so I presume you have all the .map files you need. Now to be able to put them on the phone you first need to apply the registry trick on the pc so your phone will appear as a device in My Computer (search google for this registry tweak: windows phone 7 as mass storage).
Now copy on the phone in My computer all the .map files you need.
Afterwards open TouchExplorer on your phone, navigate to \my documents\zune\content\0400 and there you will see the files but with a strange extension and name. You have to rename each file with the right map name and the extension .map (austria.map, france.map etc). After you have renamed all the files (please be patient, renaming large map files such as france will take some time so don't freak if your app will appear as frozen, it is not) copy them to the following folder:
\Applications\Data\6F9CB464-BDA......\Data\IsolatedStore\map
There you will see the already existing maps, copy your .map files here, also please be patient!! it will take some time depending on how may maps you have.
I strongly advise you to disable the screen timeout also untill you have finished copying the files!!!
When it's done you can open the Navigon Select and chose a country you have copied, it should appear if you have don all the steps wright.
Mention that if you change your simcard and HTC Connection Setup runs to auto setup your data connection you will need to open Navigon and activate it again, your maps will still be there do not worry.
Good luck!
I couldn't make Australian map working, it is only for people from Europe.
If you open the map it shows Europe and countries around Mediterarenian Sea
Related
Anyone got TomTom 5 working with Windows Mobile 5?
I received my k-Jam this morning but the setup.exe bombs out so I cannot get TT5 installed at all
any help appreciated!
thanks
Try to install the .cab file instead, it should work.
thanks but I have tried that. 3 of the 4 CAB files install but the main one (ttn.cab) - looks like its going to install ok and then you get "the file....installation was unsuccesful".
Any ideas?
Nothing on the TT site - I'm surprised that X51v or other early Windows Mobile 5 users have not been onto this one?
It seems like a problem with Activesync 4.0 initially but as the cab files don't work i guess we need a patch from them?
anyone got it working?
thanks
TomTom 5 install Problem
I had the same problem with the auto run procedure on my mini SD card.
I solved the problem by navigating to the '2577' folder and running each cab file directly on the phone (didnt use activesync). This seemed to work for me.
However, now Im having trouble with bluetooth com ports. Tomtom configuration does not show the port numbers assigned to my paired gps reciever.
Try this
http://forum.xda-developers.com/viewtopic.php?t=29282&highlight=tt5+kjam+qtek+wm5
Let me know how well tt5 runs on the k-jam ie how smooth etc as i'm awaiting my miniSD so can't try it yet!
TomTom Navigator 5.10 works with Windows Mobile 5 and Activesync 4 - but it's NOT easy. The instructions in this thread got it working for me (though I used COM4 instead of COM0):
http://forum.xda-developers.com/viewtopic.php?t=28386
Also I found that the bluetooth GPS had to be locked on to a signal for TomTom to see it at first - was fine after that.
Although my device is a HTC Universal, it has the same OS and Activesync version as your Wizard so there's no reason why it shouldn't work. Go to the above link and enjoy :lol:
Re: re: K-Jam / Windows Mobile 5 & TomTom 5
hampers said:
thanks but I have tried that. 3 of the 4 CAB files install but the main one (ttn.cab) - looks like its going to install ok and then you get "the file....installation was unsuccesful".
Any ideas?
Nothing on the TT site - I'm surprised that X51v or other early Windows Mobile 5 users have not been onto this one?
It seems like a problem with Activesync 4.0 initially but as the cab files don't work i guess we need a patch from them?
anyone got it working?
thanks
Click to expand...
Click to collapse
I had the same problem. All cabs would install except the ttn cab. Here's how I solved it.
1. uninstall everything
2. install gps.cab
3. remove sd card and soft reset (this is the important bit)
4. install ttn.cab and this time it should work
Thanks for your help guys.
sl9; How did you get 5.1 to upgrade? After copying the files from the downloaded RAR file I tried to run the setup.exe file on the phone but get a message telling me that the file is not a valid windows mobile program (perhaps it is a smartphone program).
[/quote]
aikibrown said:
Thanks for your help guys.
sl9; How did you get 5.1 to upgrade? After copying the files from the downloaded RAR file I tried to run the setup.exe file on the phone but get a message telling me that the file is not a valid windows mobile program (perhaps it is a smartphone program).
Click to expand...
Click to collapse
The setup.exe is meant to be run on your PC, it uses activesync. Obviously we know this doesn't work so the solution is to get the 5.10 upgrade from TomTom website as the ZIP FILE, NOT THE EXE - this is important
Anyway, extract the zip, and copy the directory with the 4 cab files in it to your SD card (where you have the map on). Then execute the cabs one by one, using the tip by jdee246 above if any of the cabs don't want to install.
After you install it, then the fun begins trying to get the damn thing to recognise your GPS device, see the link in my earlier post for a guide
Thanks guys - the soft reset seemed to do it. The manual install worked fine in the end.
I now have to wait for TomTom support to give me a code as I already had two a few months back so I can't report on how well it runs yet. Overall tho the Wizard/k-Jam is pretty slow - esp for screen refreshes.
I did try the BAKONL hack which I use to test TomTom on various devices but the ttn.cab on that patch just will not install for me under Win Mob 5.
thans
Thanks to all for your help.
Managed to get Tomtom 5.1 up and running. 5.1 seems to have fixed the gps connectivity problem.
The software runs on the K-JAM just as fast as it did on my QtekS110, with no problems yet.
aikibrown said:
Thanks to all for your help.
Managed to get Tomtom 5.1 up and running. 5.1 seems to have fixed the gps connectivity problem.
The software runs on the K-JAM just as fast as it did on my QtekS110, with no problems yet.
Click to expand...
Click to collapse
Hello ,
How can I install the folder "voices" because it's not a ".cab" ?
Thanks for your help.....
Who had install Tomtom 5 on the K-jam ?
Because it's too hard for me and I don't understand everything .... :?
Thanks for your help !!!!
:idea:
In total you have to copy 4 files from your wm2003 device and paste to wm2005 in these dir:
mobile device\tomtom\CurrentMap.dat
\TomTom\TomTom\data05.bmp (voice files on cd)
\TomTom\TomTom\data05.chk (voice files on cd
\Program Files\navigator\data.chk
\Program Files\navigator\tomtom navigator.exe
\Program Files\navigator\navigator.cfg
that's all.
data05.bmp and .chk is for example, you can choose one of your own voices.
Look this up on your device other wise i send you my files so you can try them.
Good Luck
GuidO
Thanks for your help !!!!!
I try this tomorrow ....
regards.
T-Mobile MDA Compact
Hi Guys
I seem to also be having problems with my MDA.
I can install tom-tom just fine, but for some reason it just doesnt recognise my Bluetooth GPS receiver. The receiver brand & model is as per this page:
http://www.qstarz.com/html/products_BT-Q770.htm
I have enabled COM 4 & 5 in the bluetooth settings page and configred tomtom to connect using either com4 or com5 but it just doesnt work.
Any help in solving this problem would be much appreciated!
Many Thanks!
This for all of you who are still having problems...
This is what i did to get my Tomtom working on my T-mobile MDA Compact:
1. uninstall tomtom using add/remove programs.
2. using file explorer deleted the following folders:
\tomtom
\program files\navigator
\program files\contacts navigation
3. Using a registry editor - browse the software sub-folders of HKEY_CURRENT_USER and HKEY_LOCAL_MACHINE and delete any tomtom, tomtom navigator, and/or tomtom gps/ tomtom bluetooth supprt folders.
(in order to avoid steps 1,2,3 you can also perform a hard reset after you have backed up all your data & files)
4. Navigate to HKEY_LOCAL_MACHINE -> DRIVERS -> BUILTIN -> BTINSerial
5. Now change the index key from 4 to 6.
6. Exit the registry editor.
7. Soft reset your MDA.
8. Now install TTN5
9. After following the initial setup prompts of TTN5 exit it.
10. Now install tomtom nav. 5.1 (update available from the tomtom website)
11. Go back into tomtom and select "change preferences"
12. Go into GPS CONFIGURATION
13. Select Other Bluetooth
14. Select COM5
15. Click Done
16. Give tomtom about 10 seconds and your GPS navigation should now work OK!!!!
Hope this helps everyone who is trying to get this to work. I have spent a lot of time trying to find a solution that works and this i feel is it!
Needless to say use this solution at your own risk - all i can say is that its worked for me!
once installed, use this procedure.
http://forum.xda-developers.com/viewtopic.php?t=32267
It works 100%
Re: T-Mobile MDA Compact
unknown01000 said:
Hi Guys
I seem to also be having problems with my MDA.
I can install tom-tom just fine, but for some reason it just doesnt recognise my Bluetooth GPS receiver. The receiver brand & model is as per this page:
http://www.qstarz.com/html/products_BT-Q770.htm
I have enabled COM 4 & 5 in the bluetooth settings page and configred tomtom to connect using either com4 or com5 but it just doesnt work.
Any help in solving this problem would be much appreciated!
Many Thanks!
Click to expand...
Click to collapse
Can you confirm that HKEY_LOCAL_MACHINE -> DRIVERS -> BUILTIN -> BTINSerial is correct - My Vairo didnt have that key...
Plus I seem to be having the same probs as you did but with the Qstarz Q880...
Terran
ttn.CAB won't install despite reset
Tried installing TT5.0 on my Vario, but no luck. Like posted before, it won't install ttn.CAB. I tried:
removing all TT files, also from registry
soft reset,
installing gps.CAB,
remove SD,
soft reset,
then install ttn.CAB
but it still says 'installation failed'. Aaarrrggghhhhh
Any ideas, anyone?
Has anyone managed to install Destinator 3.075 on Jasjar
Yes, try searching and you'll find your answers!
1. Copy across the "DestinatorApps" directory to the PPC manually using active sync instead of using the installer
2. Copy the "DestDll.dll" into the windows directory of the PPC manually using active sync
Now you have destator installed (almost) the DestDll.dll also needs to be registered!
3. to register the dll I used "regsvr_arm.exe". just copy it onto the device, and run then select the "DestDll.dll" to register it.
4. Run Destinator and active it with you licence code as you would have previously
i had problems with connecting the com ports on destinator....so i just followed these steps:
First you've got to pair your GPS.
Then go to the "COM" tab in the bluetooth manager
Add a new outgoing port with the GPS as device (use a free com port usually try every single port until it accepts it)
And then do this:
5. Copy the "DestinatorApps/Destinator/Destinator.ini" to your desktop
6. Open this in a hex editor and change where it says C.O.M.6 to the com port of your gps. Mine was Com4 so I just changed
the 6 to a 4.
7. Copy the "Destinator.ini" file back onto the PPC
steps 5-7 i dont know if this is necessary coz after i did these steps, i closed the destinator program and then ran it and the "GPS was found automatically"....but when u go to the gps settings on the destinator program its on COM 1....and COM 4 was not on the list......but i didnt bother trying to set it up as per instructions coz its already working for me......just another note, if u turn off your gps receiver while the destinator program is running and then turn on the receiver again ur not going to be able to connect to a gps satellite etc......u have to actually close the destinator program and start it again and it will again automatically connect ur gps......its a bit complicated trying to follow the instructions......but if u follow it properly it will work.......well it worked on my jasjar as well as my XDA II with WM2003SE.....good luck
yes, thanks hadn't thought of that....
of coarse I have tried searching, I have spent 3 hours doing so ... I have found lots of references especially to a post by believer... haven't as yet found the post which gives the actual full answer ...
found one which gave the ini mod for getting around the os check
-------
if anyone else is looking for answers that part is:
modify the [Platforms] section of C:\DestinatorApps\Installer\Console\Default.ini
add the line
P2577V351=ARM
-------
what I haven't found is the issue of the dll being registered.
Now that you have wasted everybodies time and had me write all of this, are you likely to be helpful and provide a link, (as you seem to know where it is) or are you more a smartass without a clue than a geovass.
Thank you irv777 nice to see someone with intelligence
no probs
davidberrysmith said:
Thank you irv777 nice to see someone with intelligence
Click to expand...
Click to collapse
You didnt search correct...
http://buzzdev.net/index.php?option...c=view&id=2529&catid=26&limit=15&limitstart=0
geovass, thanks for the link...
irv777, followed your instructions and the only thing I changed was to install from the consol and disconect the device when I got a error re registration of file. All the rest... Perfect.
Thanks again
Destinator on JasJar and regsvr_arm.exe
Can anybody please point me in the right direction as to find regsvr_arm.exe. I have followed all the directions so far and when I try run destinator I get a Destinator object creation error. The only thing I havn't done is the register bit, please.
here you go
Destinator turns off after some minutes
First of all, thank you everybody who gave instructions for the installation, of the Destinator specially for irv777. I followed the irv777 instructions and I could install the Destinator and configure the GPS perfectly. But I could notice that after using some minutes the Destinator, the screen of my Pocket PC turned off and when I turned it on again (using the light button), the GPS communication was lost because the GPS COM Port was changed. Does anybody have the same problem? Does anyone have any idea of what is happening in my case? I could realize that when I open the registry on HKEY_LOCAL_MACHINE/SOFTWARE/Apps/DestinatorApps of my Pocket PC it is different from the registry of the Pocket PC of my friend who installed the Destinator using the custom metodology (he doesn't have WM5). Is it the cause of that problem? If it is the cause how can I fix it? I don't know how to edit registry.
I havn't found any problems with it on mine. a possible work around for you might be to change the power and light settings so they don't turn off when you are using destinator.....
;-)
good luck
obviously i am doing something wrong here....
copy the destinator apps were in the ppc? i dont have enough memory eventhough my exec is recently formated (ppc 32mb free/destinator apps 36mb).
anybody?
edit: please mates.... i am leaving for a road trip in ten days and i could realy use a gps
Aussie topic - destinator cont'
hi guys,
I followed the instructions:
1. installed destinator on PC
2. copy all files (140MB) of them to the storage card
3. were trying to run ...\ARM\Independent\DestinatorApps\Destinator\Destinator.exe and got the error message described in the discussion
4. registered the dll in the windows directory...
now when trying to run the destinator.exe from the storage card I'm getting nothing (the screen flicker once)...
any ideas? any help would be appriciated.
irv777 said:
1. Copy across the "DestinatorApps" directory to the PPC manually using active sync instead of using the installer
2. Copy the "DestDll.dll" into the windows directory of the PPC manually using active sync
Now you have destator installed (almost) the DestDll.dll also needs to be registered!
3. to register the dll I used "regsvr_arm.exe". just copy it onto the device, and run then select the "DestDll.dll" to register it.
4. Run Destinator and active it with you licence code as you would have previously
i had problems with connecting the com ports on destinator....so i just followed these steps:
First you've got to pair your GPS.
Then go to the "COM" tab in the bluetooth manager
Add a new outgoing port with the GPS as device (use a free com port usually try every single port until it accepts it)
And then do this:
5. Copy the "DestinatorApps/Destinator/Destinator.ini" to your desktop
6. Open this in a hex editor and change where it says C.O.M.6 to the com port of your gps. Mine was Com4 so I just changed
the 6 to a 4.
7. Copy the "Destinator.ini" file back onto the PPC
steps 5-7 i dont know if this is necessary coz after i did these steps, i closed the destinator program and then ran it and the "GPS was found automatically"....but when u go to the gps settings on the destinator program its on COM 1....and COM 4 was not on the list......but i didnt bother trying to set it up as per instructions coz its already working for me......just another note, if u turn off your gps receiver while the destinator program is running and then turn on the receiver again ur not going to be able to connect to a gps satellite etc......u have to actually close the destinator program and start it again and it will again automatically connect ur gps......its a bit complicated trying to follow the instructions......but if u follow it properly it will work.......well it worked on my jasjar as well as my XDA II with WM2003SE.....good luck
Click to expand...
Click to collapse
Is the procedure similar if you have an embedded GPS?
I have a Mio P350 & want to put Destinator 3 on it, do you install the console on the PC first, if so what files & from where do you install on the PDA, & what do you install on the SD card?
Appreciate any help I can get, as the MioMap v3.2 is driving me crazy!
Ive done everything there is to do to try to activate windows 7 live and market....tried 4 times and I cant change the HD2 saying its a Leo70...How do I change that in order to download apps from the market.... any help? thanks
topspin72 said:
Ive done everything there is to do to try to activate windows 7 live and market....tried 4 times and I cant change the HD2 saying its a Leo70...How do I change that in order to download apps from the market.... any help? thanks
Click to expand...
Click to collapse
You have to do exactly this:
1. Install WP7 sdk Windows Phone Developer Tools;
2. Install zune;
3. Make partneship with zune and phone;
4. Attach the ChevronWP7.cer(you found in the toolkit) to your email and send the email to your email itself (On PC);
5. Login to your email account (On Phone), Open the email, Select attachment and install the cert;
6. Connect your phone to pc and make sure zune is running in background;
7. Run the unlocker (ChevronWP7.exe) and click unlock button(Make sure your phone date is set correctly)
(you need to close skype and disable network adapter.. hamachi.. wireless.. Dropbox.. etc)
6. Install toms .xap installer;
7. Deploy Connection Setup.xap, Touch Xplorer.xap and XBMODDeployer.xap (Install it on the phone and run XBMODDeployer.xap);
8. Copy the .provxml from the ringtons folder to the windows folder (on the phone using touch explorer app);
9. Run connection setup to install the .provxml;
10. Call Microsoft helpdesk and ask them an activating key for your hd2 (don't pm me for the key)
11. Setup up your live ID and enter the activation code (on the phone).
The whole thread is here: http://forum.xda-developers.com/showthread.php?t=911579
Ive dont that whole process like 4 times and my phone is always a leo70 and I cant download apps from the market after activation with a key that I got from MS.
you sure you did this part
8. Copy the .provxml from the ringtons folder to the windows folder (on the phone using touch explorer app);
9. Run connection setup to install the .provxml;
yes several times
topspin72 said:
yes several times
Click to expand...
Click to collapse
Start from scratch again then, Make sure you don't skip ANY steps, as they are all important.
Alrighty one more time thanks
make sure date & time is not automatic
and that ur location is us
activating live services took me 2 days. i ended up having to do a clean install of windows 7 64bit ultimate
Hi everybody.
I'm disappointed, I've looked all the posts in this forum and in the french one (HTC DEV). I have followed all the instructions and I'm still locked after the click on the unlock button in chevronwp7 with uhoh message.
register base ok
chevronwp7.cert on the phone
zune full synchronized (not guest)
host file free to write
port 443 free
no firewall no anti virus
no skipe
airplane mode on or off (the 2 modes tested)
task29 done and re install WP7
windows 7 re installed
zune re installed
What have I forbitten?????
cheap66 said:
Hi everybody.
I'm disappointed, I've looked all the posts in this forum and in the french one (HTC DEV). I have followed all the instructions and I'm still locked after the click on the unlock button in chevronwp7 with uhoh message.
register base ok
chevronwp7.cert on the phone
zune full synchronized (not guest)
host file free to write
port 443 free
no firewall no anti virus
no skipe
airplane mode on or off (the 2 modes tested)
task29 done and re install WP7
windows 7 re installed
zune re installed
Are you running Windows 7, have you installed the SDK, have you installed Zune and have you followed this guide to the letter?
http://forum.xda-developers.com/showthread.php?t=911579
What have I forbitten?????
Click to expand...
Click to collapse
Do all of that and you should have a working phone that is unlocked.
1. Install WP7 sdk Windows Phone Developer Tools; done
2. Install zune;done
3. Make partneship with zune and phone;done
4. Attach the ChevronWP7.cer(you found in the toolkit) to your email and send the email to your email itself (On PC);done
5. Login to your email account (On Phone), Open the email, Select attachment and install the cert;done
6. Connect your phone to pc and make sure zune is running in background;done
7. Run the unlocker (ChevronWP7.exe) and click unlock button(Make sure your phone date is set correctly)done
(you need to close skype and disable network adapter.. hamachi.. wireless.. Dropbox.. etc)done
still locked
Are you doing a full hard reset and then reinstalling the certificate? It should work after the PortalUrlProd and PortalUrlInt values get returned to the default.
yes I have done by pushing + and - volume button
solution
the default year in WP7 is 2010 it took me a while to realize i was forcing the phone due to the date.
small thing easy to overlook hope it helps
edit: with the correct date phone should unlock
cheap66 said:
1. Install WP7 sdk Windows Phone Developer Tools; done
2. Install zune;done
3. Make partneship with zune and phone;done
4. Attach the ChevronWP7.cer(you found in the toolkit) to your email and send the email to your email itself (On PC);done
5. Login to your email account (On Phone), Open the email, Select attachment and install the cert;done
6. Connect your phone to pc and make sure zune is running in background;done
7. Run the unlocker (ChevronWP7.exe) and click unlock button(Make sure your phone date is set correctly)done
(you need to close skype and disable network adapter.. hamachi.. wireless.. Dropbox.. etc)done
still locked
Click to expand...
Click to collapse
On #5 did you use touchXplorer to copy that file to Windows directory?
Remember Zune will lock you HD2 everytime you connect your usb. use the crack in this forum to prevent that.
are you using windows XP?
Also try putting chevronwp7.exe in the root of your c: drive and run as administrator. I've seen people say that it isn't necessary, but I had to.
Also if you're using vista or windows 7 make sure UAC is disabled.
besides turning off the firewall, i turned off the windows defender service.
It might do the trick.
Solved
Thanks to everybody
My problem is solved.
Like audit angel was saying the default year is 2010, and the solution was there for me.
When I changed the year to 2011 Chevronwp7 did his job.
What an idiot I was!!!
I have made it all the way to the part where u run connectionsetup.xap,touchxplorer.xap
everytime I unzip this it will not run them correct, it always tries to open the files in a read me or something instead of running the program.......sucks please help
dman35501 said:
I have made it all the way to the part where u run connectionsetup.xap,touchxplorer.xap
everytime I unzip this it will not run them correct, it always tries to open the files in a read me or something instead of running the program.......sucks please help
Click to expand...
Click to collapse
Ok I think you missed some steps, so lets start from the top. First of all you cant "RUN" or "Execute" a .xap file. Its meant to be installed or "deployed" to your phone, not PC, through the Application Deployment software provided in the Windows Phone 7 SDK(Step 1). Only after installation of Windows Phone 7 developer tools can you go through steps 2-6, and then on step 7 go to your PC's Start>All Programs>Windows Phone 7 Developer Tools>Application Deployment. Choose the Brows button and the two .xap files(1 at a time) and deploy them to your device. After you complete that you can proceed to steps 8-10.
If you find this to be confusing you may consider a Cooked Rom as many of these features are already provided. Good Luck.
1. Install WP7 sdk (Not confrimed, Skip and see if it works);
2. Install zune;
3. Make partneship with zune and phone;
4. Attach the cert to your email and send the email to your email itself (On PC);
5. Login to your email account (On Phone), Open the email, Select attachment and install the cert;
6. Connect your phone to pc and make sure zune is running in background;
7. Run the unlocker (ChevronWP7.exe) and click unlock button(Make sure your phone date is set correctly);
6. Install toms .xap installer;
7. Deploy Connection Setup.xap, Touch Xplorer.xap and XBMODDeployer.xap (Install it on the phone);
8. Copy the .provxml from the ringtons folder to the windows folder (on the phone using touch explorer app);
9. Run connection setup to install the .provxal;
10. Setup up your live ID and enter the activation code (on the phone).
dman35501 said:
I have made it all the way to the part where u run connectionsetup.xap,touchxplorer.xap
everytime I unzip this it will not run them correct, it always tries to open the files in a read me or something instead of running the program.......sucks please help
Click to expand...
Click to collapse
Just use a cooked rom, why stress yourself with the original one, when you can use a cooked rom and have all that done already for you..?
Link?
CrAzYiaN said:
Just use a cooked rom, why stress yourself with the original one, when you can use a cooked rom and have all that done already for you..?
Click to expand...
Click to collapse
A link to your cooked ROM would have been nice!
this one works for me
http://forum.xda-developers.com/showthread.php?t=1356833