Related
I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....
try :
on the htc :
Start
setting
other
USB to PC
and enable faster data sync...
hope that help you.
Thank you I will try that now and will update in a few minutes..
NO still no good same thing again, it's a pain as it keeps leaving my phone in bootloader mode so I have to keep removing the battery...
tanzi said:
I am trying to install a a new rom on my Leo, I sync my device then run SSPL_RUU it starts fine then it puts my Leo into Boot mode then it says " ERROR (206): CONNECTION
The update Utlilty cannot connect to you PDA,Please check that between the PC and your PDA Phone" your USB cradle/cable is connected properly" I have tried anothe USB port but still the same thing, the PC and Loe do connect as I have just synced them so I don't understand the problem, I am running windows 7....
Click to expand...
Click to collapse
Hi
Step 1: Right click on SSPL and "run as administrator" it will be do the job.
If you get an error then Disconnect the cable and reconnect then run the Step 1 again.
Good luck
Thank you I will try that now..
It didn't work I did it twice but still the same, I am at my wits end with this arghhh....
tanzi said:
It didn't work I did it twice but still the same, I am at my wits end with this arghhh....
Click to expand...
Click to collapse
If you use a USB Hub then try use the usb port from the motherboard.
OR
Try to Install HSPL first. then Install any roms with Custom ruu. Please read the thread before you use them. They all explained here
http://forum.xda-developers.com/showthread.php?t=609477
Good luck
1) To install this HSPL there must be SPL 1.42.0000 on your device.
Otherwise the installation will fail!
To check your SPL version, hold the Volume Down button and do a reset.
It is possible to downgrade to this SPL, by just flashing to an Official ROM
with this SPL version.
Click to expand...
Click to collapse
For instance my is SPL 1.42.6666 and I have same problem.
Troubleshooting:
* I have SPL 1.42.666 on the device.... !!!! WAIT !!!! SPL 1.42.6666 is not the version of the SPL on your device!... it is the SSPL version. Most likely you have the needed 1.42.0000 SPL on the device, just try to install this HSPL if you need it. Don't worry, if there is not the right SPL on the device, then u will get an error message, but nothing will happen to your device
Click to expand...
Click to collapse
I had same kind of problem, I also run windows 7 I simply swaped to a different usb plug and then it worked fine. I was useing the plugs on the frount of pc's case so I wonder if the internal cable has a small problem or somthing as all other things work fine from that plug.
Hope that may help you.
Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...
tanzi said:
Imanaged to get HSPL on my device and I manged to flash the rom to this one " Touch-IT Black Leo HD2 - updated " and it seems really good, the question I would like to ask now is how do I put the original rom back should I need to for warrenty issues? also does this mean that I can now use all the other roms that are on here? and is there a rom that anyone would highly recomend? Thanks for all the help that has been given to me, this really is a great forum with really helpful people...
Click to expand...
Click to collapse
Wel done
If you want to uninstall the HSPL then follow this
Uninstallation
Only way to remove the HSPL is to flash an original SPL from SD card.
- Take any "RUU_signed.nbh" from a ship ROM and copy it to SD card.
- Rename it to "leoimg.nbh"
- Reset the device while pressing the volume down button.
Recommend any roms is not easy because it depends your usage pattern. Therefore read more in the LEO threads before you choose to download any rom.
Now you have HSPL therefore you can install any rom from here
Good luck
ALWAYS USE SEARCH FUNCTION HERE AND YOU WILL FIND ANSWERS.
Thank you for explaining everything in a way that I can understand, I am not very techy so understanding exactly what to do when written is very important so thanks again..
So....i had read the thread and installed HSPL on my phone before i attempted to used a cooked rom, having tried to install my first one i find now i have the 'white triangle of death with upside down exclamation mark'.
I am on T-Mobile in the UK and i do not want to brick this beyond all repair..what is the procedure i should do now to get it working..i beleive i need to format a SD card to fat32 but which rom do i put on it and then what is the button press sequence..i have no connection via active sync anymore.
phone off - hold "volume down" - tap power whilst still holding volume down - phone will boot to bootloader (three stripes)
what does it say next to spl?
if
1.42.0000 then hspl isn't installed. what rom did you flash and how?
if says 1.42.HSPL then hspl is installed, plug in usb, wait for "serial" to become "usb" and flash your rom again from usb.
Thanks...
1.42.HSPL is what it says, it also says lower down 'upgrade ROM code error please try again' which i did do several times through the .exe on the rom i tried to upgrade to which i believe was TOUCH_X_TREME_21895_1_2_36_47, im not to sure whether the rom is compatible for me or even what i done wrong, i was relying on the fact that i had installed HSPL prior to trying to flash the new rom, i can confirm that the phone changes to 'usb' when i plug it in on the tri colour screen...so when you say try to flash the rom again what exact method do i use..when i tried the first time i just run the .exe file in the rom folder and followed the prompts
EDIT: having just followed what you said...i run the rom .exe file and followed through recovery and it says error 'error 302 update error'...what if the rom i am flashing is NOT compatible.
Why don't you first try to flash back a stock rom that you can download from http://www.4shared.com/dir/22189940/b8552fa0/Shipped_Leo_ROMs.html ?
Choose preferably a 1.48 rom.
Anyway, you'd better read the "flashing for noobs" thread in ROM dev forum before you go and do something even worse. You're probably trying to flash a corrupt file or something alike.
get the T-Mobile ROM from HTCs website, boot into the bootloader and connect and flash the stock ROM...that should at least get you working again
yea as above.sounds like a bad download or something. try a different rom or re download.
be aware the rom you are flashing needs a certain radio, so when it does flash it still won't boot till you flash the correct radio.(it's all in thefirst posts of the rom thread)
you have hspl installed so as long as you only flash by usb you are safe. just boot to bootloader, run the instal from the pc, phone will flash
EddyOS said:
get the T-Mobile ROM from HTCs website, boot into the bootloader and connect and flash the stock ROM...that should at least get you working again
Click to expand...
Click to collapse
Have done this..still not flashing, keeps giving update error, as i said..i have no active sync connection and it states that is needed ?...so how do i flash the rom ? also when you asked me to go to the tri colour screen and read off the HSPL part, on the green section it says 'upgrade ROM code error please try again'..is this normal in this state
Why am i getting this error when i try to flash it via usb...comuter still recognises phone but active sync does not connect to it so i am assuming this is causing the error ?
So when you go into the bootloader and plug in the USB does it say USB on the phone screen? If so, you also need to run the updater as an administrator. If this doesn't work, try another PC. If that doesn't work then you may very well have bricked it.
Also, are you using ActiveSync or WMDC?
EddyOS said:
So when you go into the bootloader and plug in the USB does it say USB on the phone screen? If so, you also need to run the updater as an administrator. If this doesn't work, try another PC. If that doesn't work then you may very well have bricked it.
Also, are you using ActiveSync or WMDC?
Click to expand...
Click to collapse
Yes it changes to USB when i plug it in, i am using WMDC but when i plug the phone in it does not connect anymore, i have tried running as admin but it makes no difference, i keep getting error 302.
Correct me if i am wrong, i thought the idea of installing HSPL would keep me safe from bricking the phone, i think all i initially done was flash an incorrect rom, ill try it on my laptop but that has not been in contact with the phone yet
What OS is on your laptop? if it's Windows 7 just plug in your phone and it will automatically WMDC so you don't need to install it first
Laptop done the trick !..seems to be doing the job now...dont know what the hell thats all about...
Would be helpful if knew what radio i had on it...and do i install rom first, then install radio ?
ActiveSync or WDMC wont recognise the device as the phone has not fully booted up.
With the phone in boot-loader mode and connected by USB, then run the ROM installation program. Ignore the fact that it says you must be ActiveSynced. Just tick the box and go into the next page.
As been said already, make sure you install the correct RADIO rom for the customised ROM. Once that is done, then you can install the ROM.
The best ROMs to download are ZIP'd or RAR'd ones, as they have a check that they have not been corrupted when uploaded or downloaded.
Well this is highly weird !!...i restored the Tmo dump from htc website but i now have the rom on there that i was trying to install previously before i bricked it...Touch X treme
What radio are you trying to flash? Read this and use this to flash the phone with the radio needed for your ROM choice:
http://forum.xda-developers.com/showthread.php?t=644781
Once done, try flashing the phone again (I'd make sure HSPL is on the phone too)
fred_up said:
ActiveSync or WDMC wont recognise the device as the phone has not fully booted up.
With the phone in boot-loader mode and connected by USB, then run the ROM installation program. Ignore the fact that it says you must be ActiveSynced. Just tick the box and go into the next page.
As been said already, make sure you install the correct RADIO rom for the customised ROM. Once that is done, then you can install the ROM.
The best ROMs to download are ZIP'd or RAR'd ones, as they have a check that they have not been corrupted when uploaded or downloaded.
Click to expand...
Click to collapse
So find out what radio i need before flashing, what if the radio i need to flash is not for the currant rom i am using...and am i right to say that some of these roms i cant use as they are not for the UK ?
All radios can be used, you can get them on their own and use with that link I posted before. going by the Touch X thread it says you need a 2.07 or 2.08 radio so get one of them and flash that first before flashing the ROM
I understand that better now...still not sure what went wrong there, from the laptop i thought and still do that i was flashing the stock rom for tmo from the htc website to restore the phone...but when it started up i was shocked to see the splash screen for the Xtreme rom..maybe i flashed that ?? if so why did it work this time..bad flash before ? and i have certainly not installed a radio myself...well thaks for your help anyway..the phone is up and running again and i will make sure HSPL is still there before i try my next rom
Likely bad flash - glad you're sortred now though. I always do the task29 with the radio nI want to use before flashing a ROM now to make sure the memory is clear...
Hi everyone! At first sorry because my english is not better than my french
My problem: I have an HTC hd2 with a white screen and the SPL 1.42.0000 (i can go to bootloader). I google it and can't find any solution, i tried to instal HSPL (with hspl2/3/4) without success (usb fail connection) i have the same error with an task29, and an hd2toolkit. I tried to instal from sdcard but i have the error "radio v2 fail".
I think this is a problem at height of XDA developers ^^
PS:I tried to change Computer or usb port and execute as administrator but nothing...
If you coul help me it will be realy nice.
is the phone recognized in device manager? If not its a driver problem.
also do the usual ( verify its not the usb cable, try different usb port,) if drivers are ok
thank you for your help
The computer recognize the device but without OS (white screen) i can't do anythings with Activesync, i tried other computers and other usb port/cable but nothing. I think isn't a driver's problem because the instalation with sd card don't work.
Anis92 said:
The computer recognize the device but without OS (white screen) i can't do anythings with Activesync, i tried other computers and other usb port/cable but nothing. I think isn't a driver's problem because the instalation with sd card don't work.
Click to expand...
Click to collapse
Don't understand what you mean by "white screen"?
Try installing a stock winmo for you device to make sure everything is ok...
i tried to instal an official htc rom from sd card but it doesn't work, by "white screen" i just wanted to say that when i turn on my phone the screen is white.
It sounds like you have done a Task 29 and you do not have a ROM on your HD2 right now. This is why you just boot to the white screen.
You do npot have to use Active Sync or Windows Mobile Device Center to flash via RUU. You just have to have them installed because the haqve the USB drivers for the HD2's WINCE Bootloader in the programs and they install the drivers when you install the program.
The drivers in Active Sync and WMDC allow you to have a HTC Sync connection in the bootloader. Just boot into the bootloader by holding down the volume down button while powering on yuour HD2. Next connect your HD2 to your computer via USB cable. Wait and watch for the Serial in the white bar of the bootloader to change to USB. When you see USB you can run a RUU.
Now to address your 1.42.0000 SPL, this is a older SPL version and you may have to keep trying different RUUs until you get one that will flash. Just make sure if you have a T-Mobile HD2 that you do not flash any radio version below 2.08.50.?? or any radio version that has a 51 in the radio where the 50 is in the first radio I mentioned, or you will brick your T-Mobile HD2. Look for the radio version in the RUU name it will be there.
Sometimes the HD2 develops what is referred to as a "stuck radio" when they have these early SPL versions like yours. This is why I say you may just have to keep trying different RUUs until you find one that will flash.
Hey there Community,
I really don't know much about mobiles, especially the HTC HD2 and flashing ROMs,
but somehow I got Android to work on my HTC HD2 1 year back and now wanted to sell my phone because I got a new one.
Therefore I needed to set up the factory settings and get Windows Mobile 6.5 back on my phone..
Unfortunately I failed hard while following the instructions of a tutorial that said I only needed to rename ruunbh to leoimg and put it on my SD-card and so on.
Halfway the update was interrupted and since then Iam getting "00028002 Not allow" error and can only boot to the bootloader saying "Upgrade ROM code error Please try again" And the usual things in the red disctrict and at the bottom it says that I got an USB-connection which seems to be wrong, because I can't see the device and so on.
I tried to install HSPL4 but it failed due to no USB-connection.
So what can I now do to make it work again? Iam really frustrated
Flashing image from sd is all good if it original correct country/vendor rom, if not you get your problem & things can be tricky as HSPL was replaced with standard SPL so care must be taken.
Either find a correct Vendor/country (CID) ROM for your HD2 or get it in bootloader & able to flash HSPL.
Would of thought for resale a good Android build would be more desirable.
I know what you mean, but the problem is that I just don't know what to do..
My phone is not branded or anything, so I couldn just go to htc.com and get me the newest winmo Rom?
The Problem is, what to do then, exactly?
It seems that I can't flash anything because I dont got usbconnection..
So no idea to original ROM country vendor !
usb connection may be due to driver issue on PC, install Activesync if on XP or WMDC 6.1 for Vista & Windows 7 then retry connecting hd2 via usb .
*Also make sure you know your version of HD2 & be aware of .51 radios killing US T-Mobile HD2s.
Try to flash 2.08.HSPL only (also in HSPL4). It is enough. You can also try these drivers to fix your USB connection.
And here you can find offical ROMs.
Drivers linked above are not suitable, install activesync or WMDC is best option.
Finding original ROM is not going to be easy if you have no clues to origin of handset ...
Also, just cost you don't "see" the phone from the p c doesn't mean you don't have a USB connection.... it will never show up in your drives list like it does when an os is running, and activesync (or wmdc) will also not see the phone when it's in bootloader.
If the phone shows "USB" (and your PC may even "ding" when its plugged in, that's all you can expect unless you look deeper,, into the hardware list, for example.
What does hspl line say?
I'd do....
Hspl4, choose 3.03.hspl (NOT 3.03.0000)
Flash unbranded 3.14 rom from USB
Report back.
I have same story - 00028002 not allow+no usb.
no one stock rom can be flashed.
completely lost and no idea what to do.
Hi!
I've been using an Andriod NAND for like 2 years now and decided to upgrade to IcecreamSandwich. I installed HSPL 2.08 which I believe I had before anyway. Then I tried updating my radio but I get connection error 262. Apparently my phone wouldn't synch with WinMobileDeviceCenter. When I bootload I get serial and when I plugin it changes USB. But device doesn't get recognized. after rebooting I can start my Android no longer - MAGLDR 1.11 says ...boot mount failed. So I'm stuck in MAGLDR 1.11 and I can't ever restore to WinMobile original ROM. Any ideas?
slickie said:
Hi!
I've been using an Andriod NAND for like 2 years now and decided to upgrade to IcecreamSandwich. I installed HSPL 2.08 which I believe I had before anyway. Then I tried updating my radio but I get connection error 262. Apparently my phone wouldn't synch with WinMobileDeviceCenter. When I bootload I get serial and when I plugin it changes USB. But device doesn't get recognized. after rebooting I can start my Android no longer - MAGLDR 1.11 says ...boot mount failed. So I'm stuck in MAGLDR 1.11 and I can't ever restore to WinMobile original ROM. Any ideas?
Click to expand...
Click to collapse
if you put the phone in bootloader (4 colors Screen - HSPL 2.08 exc..) and show up USB when you connect it to the PC, it should be recognized from the application flasher, no PC.
Try to go in bootloader and when you connect the phone to your pc and when show up USB try to upgade and flash MAGLDR 1.13, (no MAGLDR 1.11 the old one) the last one.
Are you sure you used the right Radio for Leo?
thanks
eclyptos said:
if you put the phone in bootloader (4 colors Screen - HSPL 2.08 exc..) and show up USB when you connect it to the PC, it should be recognized from the application flasher, no PC.
Try to go in bootloader and when you connect the phone to your pc and when show up USB try to upgade and flash MAGLDR 1.13, (no MAGLDR 1.11 the old one) the last one.
Are you sure you used the right Radio for Leo?
Click to expand...
Click to collapse
When I try updating either the radio or MAGLDR in the install instructions there is this step2 where I have to establish an activesynch with my phone. I can't. So when I run the update it starts but progress stays at 0% both on PC and phone screen. After a few minutes I get error 262.
I'm trying to install radio 2.15 from Jayce Ooi's Paradise
Forget about active sync, you will never get an active sync connection unless win mo is running,, ,that'snot what the instruction to "get an active sync connection" means. It means get a USB connection, which uses the active sync drivers.
Try different usb ports,,do not use a front mounted usb port,only theones inthe back of the machine.
samsamuel said:
Forget about active sync, you will never get an active sync connection unless win mo is running,, ,that'snot what the instruction to "get an active sync connection" means. It means get a USB connection, which uses the active sync drivers.
Try different usb ports,,do not use a front mounted usb port,only theones inthe back of the machine.
Click to expand...
Click to collapse
Why do I get this connection error then?
I did try different USB ports. Even tried different PCs. Same thing.
slickie said:
When I try updating either the radio or MAGLDR in the install instructions there is this step2 where I have to establish an activesynch with my phone. I can't. So when I run the update it starts but progress stays at 0% both on PC and phone screen. After a few minutes I get error 262.
I'm trying to install radio 2.15 from Jayce Ooi's Paradise
Click to expand...
Click to collapse
find another radio from XDA for HTC HD2, "radio 2.15? What this mean? from Jyce Ooi's Paradise" do not mean anything, I know Jayce and he is an amateur, not master.
You don't answer on questions given to you, if you want help, do you flash from bootloader? turn-off phone, keep pressing volume-down, press button on?
In bootloader, when you connect to pc, show up USB on the bottom of the screen?
eclyptos said:
find another radio from XDA for HTC HD2, "radio 2.15? What this mean? from Jyce Ooi's Paradise" do not mean anything, I know Jayce and he is an amateur, not master.
You don't answer on questions given to you, if you want help, do you flash from bootloader? turn-off phone, keep pressing volume-down, press button on?
In bootloader, when you connect to pc, show up USB on the bottom of the screen?
Click to expand...
Click to collapse
The same thing happens even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship). What question haven't I answered? Yes, I flash from bootloader and yes USB shows up on the bottom when I connect it to the PC. When the updating of the ROM image starts there is no progress - neither on the instalator, nor on my phone (it shows HTC and a progress bar with 0%). After a couple of minutes I get Error 262 and "The ROM update utility has encountered a communication errors during update process."
Is my phone bricked?
slickie said:
The same thing happens even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship). What question haven't I answered? Yes, I flash from bootloader and yes USB shows up on the bottom when I connect it to the PC. When the updating of the ROM image starts there is no progress - neither on the instalator, nor on my phone (it shows HTC and a progress bar with 0%). After a couple of minutes I get Error 262 and "The ROM update utility has encountered a communication errors during update process."
Is my phone bricked?
Click to expand...
Click to collapse
Bricked mean dead, no life at all, your still alive but there is some errors, you should be happy to turn-on the phone in bootloader and usb be recognized. You have to try flash ONLY Radio 2.15.50.14.
If you can't flash the radio which I told you try to erase your rom with this tool.
you can update you magldr 1.11 to 1.13
you can update you magldr 1.11 to 1.13:highfive:
even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_S igned_15.32.50.07U_2.07.51.22_2_Ship
Click to expand...
Click to collapse
thats not a radio, thats a rom that includes a radio, but also includes an spl, , 1.66.0000
Are you SURE it still says x.xx.HSPL in bootloader? because hanging at 0% is very often associated with not having hspl installed.
samsamuel said:
thats not a radio, thats a rom that includes a radio, but also includes an spl, , 1.66.0000
Are you SURE it still says x.xx.HSPL in bootloader? because hanging at 0% is very often associated with not having hspl installed.
Click to expand...
Click to collapse
exactly, I forgot about that!
Also if you really have x.xx HSPL is no more a problem of you Phone but of you PC, so try different OS, even XP, and still trying. IS NOT THE PHONE.