Soft buttons very unresponsive. - Streak 5 General

Hi,
I'm begging for some help. I had this problem that my soft buttons were getting pressed by themselves. All of the sudden when I was browsing the phone vibrated 3 times and all the sudden I was 3 steps behind. Or when I opened an app it vibrated and whent back to the home screen. I noticed the if I pushed the buttons hard it would stop for a while but it would start after some time again. This morning it really pissed me off so I turned of the phone and pushed all 3 buttons really really hard and up and down. I turned the phone back on and it didn't do the probem. At first I thought it would start after a few hours but it has been over 12 hours the problem is still gone. That makes believe that there is some connection problem under the plastic of the touch button.
Now I have a new problem. The back key is very unresponsive. I have to press it 2-3 times in order for it to work or I have to press it really hard witch is not very good.
Is there a way I can calibrate the sensitivity of the soft buttons or open the phone and clean the contacts or something? What do you guys recommend?
If I take it to service they will keep it for over 3 weeks and I don't have a spare phone. I will do this only as a last resort.
Thanks
Sent from my Dell Streak using Tapatalk

I think the buttons you are talking about are the back/menu/home button on the right hand side of the screen. As far as I know they use the capacitance of your finger to detect when they are pushed. No electrical contact is made as a result of the button press.
Has your steak been pulled apart before? If so, there is a possibility (unlikely) that the connector to that circuit isnt properly connected.
There is an app called soft keys or similar that will give you these virtual buttons if yours dont work properly.
It could just be one of those things. (ever tried using a hot steak when you have cold hands? Or put a warm greasy fingerprint on it? It fools the screen)
Best of luck.
Sent from my Dell Streak using XDA App

My streak has never been bulled apart before. I don't understand why this is happening to me
Sent from my Dell Streak using Tapatalk

Related

hard and soft buttons intermittently working?

I'm having a strange problem with the hard and soft buttons on my phone.
I went to the park to take the kids to the pool yesterday. No, I didn't get within 100 feet of the pool with my phone. It was not placed anywhere wet and no one, as far as I can tell, got close enough to drip on it. It acts like it got water inside, but unless it somehow condensed from the air or from sweaty hands, I don't know how that could have occurred.
Anyways, I had set my phone up and when I picked it back up, it was like I kept pressing the messaging and IE buttons. Eventually letter keys on the keyboard like Q and E kept appearing as well. Every now and then it would work fine for a few minutes and then start up again. After leaving the phone out in the direct sun for awhile, it stopped doing that even as much but some of the keyboard keys and most of the soft keys seem not to want to work at all, neither do the two phone keys or the directional pad. Pressing the middle button on the directional pad causes the alignment screen to come up (???).
Making matters more confusing is the fact that on a couple of occasions when I did a soft reset the buttons would seem to function normally for a time. Most recently it happened last night when I went out to lunch. I had reset my phone and all of the buttons seemed to work fine again for several minutes. I got back from lunch and proceeded to browse the forums here. When I went back to my phone a bit later and had to wake it from standby, the issues returned. I have since flashed to a new ROM but have experienced no change in the symptoms and have not gotten the buttons to work with a reset since, though I've admittedly only tried a couple of times. When I tried doing a hard reset, it instead went to the bootloader screen.
So, yeah, I'm confused. It acts like it got moisture in it but I don't know how that could have happened unless it was just from my hand. In any case, trying to dry it doesn't seem to have helped. Does anybody have any ideas on this or am I buried? It's several months still before I can upgrade to a new phone at a discount with my provider and I really don't have the money to do so in any case. I can use the touch screen but, let's face it, the WM interface is a lot easier to navigate sometimes with the buttons. I'm holding out big hope for the WNAIP project to succeed here though. Of course, that's not to mention I can't play games like Tetris without a working directional pad.
Okay, it's pretty much gotten to the point where none of the physical buttons works, hard or soft, and even some of the kb buttons don't work.
Anyone?

Streak Touch Response Messing Up

This just started yesterday but the bottom of my screen (the side where the serial port is) seems to be less responsive than normally. When I go to click to respond to a text message I find myself having to press it repeatedly. Sometimes the whole screen becomes un-responsive or if I click up top it will actually make a response at the bottom. Could this be at all due to an app or something I installed? Because normally when I put it on standby (pressing the power button once) and turn it back on it will fix it all but the unresponsive bottom section for texting only. Does this make sense to anyone why this could be happening?
Just having touch problems all together
i keep pressing the screen so many timees... even tried to restart and take the battery out. but still same problems
any help
Thanks
Try recalibrating the touch screen guys, that might help. Also if you have a screen protector on, try removing it, I found my first one got more unresponsive over time.
I dont like screen protectors for that very reason and dont use them. But where is the screen recalibration? I've looked and looked for it since this started happening. It's half way working now and really just varies. So if there is a way to calibrate I really feel like that would fix it. Thanks!!
Sent from my Dell Streak using XDA App
yeah mine did that and calibration fixed it.
power it off, hold down both volume buttons and power it on, holding down all three until the menu appears.
Choose option 3 and away you go!
hth....
Haha, this completely fixed it!!! I'm so excited right now becaus I was terrified I did something to it. It works perfectly again. Thank you guys so much!!!
Sent from my Dell Streak using XDA App
It's nice to be able to give some advice that works for a change

The Infamous Unresponsive Digitizier Screen Possibly Solved!

Okay I wasnt going to post about this cause there have been way too many posts and alot of back and forth and debates and even flaming, but I stumbled across something that I think is the cause for MAJORITY of the issues with why we keep having this happen. It Happened to me Today, and I Found the cause.
Before ANYONE Flames me for bringing this up, READ the post, Remember I solved the cause of why it happens to most of us, I dont take responsibility if you choose to take it upon yourself to fix it! And I know 90% of the users are going to tell me I'm wrong or I dont know what I am talking about, so be it.
If you have nothing to add other then flaming the post, just hit the back button and be on your merry way and pretend you never saw it. But I am 98% sure I am right about why its happening!
So if your interested read on:
I actually for the first time had this, and I know this is going to get flamed but its not the Screen thats the problem. And I think (BIG IF) that the dreaded unresponsive screen issue that we keep reading about Majority of them I think is not the screen.
I have 2 HD2s and both have worked flawlessly without any problems, but today I was playing with my test phone that doesnt get used that much and I noticed after installing a new rom that my screen after I played with it for a bit went black (sleep) and when I woke it up it wouldnt respond, first thing that crossed my mind is I just lost my digitizier, and started wondering okay why, I went as far to re-flash WinMo stock HD2 rom, same issue, so I decided its time to find out exactly whats causing this, and I found it. I wasnt going to make a post again cause I figured people would be "Not another thread about this" but I know whats causing the screen issue, at least this is my suspicision and I have temporarily fixed mine.
The problem is HARDWARE, The Culprit: THE END KEY (Red Button)! The Answer to "How or Why": The "End" key is used to turn the phone on and off or to put it in sleep mode, it is the most used key out of all 5 keys, it is used probably 7x more then all the rest, Its used for just about everything, now how does this cause the unresponsive screen? Easy, the phone lock or sleep is associated with this key, Its the only way to make the screen go off other then waiting for the time out period. Because by habit we mostly hit the end key to turn the screen off the phone automatically associates this with locking the phone, once that happens the screen becomes unresponsive because of several reasons: 1) The contact under the actual key has dirt which causes the button to stick in the down position, 2) the contact is bent which the "end" key is pressing down on the contact which is making contact with the board and causing it to be unresponsive, 3) The contact is worn. This is the reason why if you press the end key a few times (anywhere between 2-10) and then try the screen responds, this is cause your "unsticking" the key which then lets the screen respond.
Most of us when we hit the end key press to the far right to avoid hitting the back key (The button with the left arrow) which causes the end button to lean toward the right. But you can wake the phone up with the other 4 keys to the lock screen which will allow you to unlock the phone. As a temporary fix for myself, on my test phone I now make sure to press on the left side of the key to prevent this from happening, since its a test phone I'm not worried, but the real solution is to take the phone apart and clean the underside of the end button, and the actual contact with alcohol to remove the build up of dirt and whatever else. And also if the contact frame is bent to GENTLY bend the right side back up alittle to stop it from happening, or sending it to htc and letting them fix it.
We have to RE-TRAIN ourselves to start using the other keys to wake the phone up and not rely on the end key so much.
Hope this helps anyone finally why we have this problem. And if it works for you then hit the Thanks button
I completely agree with you. I've had the "dead digitizer" since December. It was pretty apparent it was a hardware key problem, as I could generally solve the issue by pressing the "Off" button to turn the screen off, and then one of the other keys (usually the back button, but occasionally one of the others) to wake the screen up, and the digitizer would be alive again.
As I am still under warranty, I sent mine off last week, and expect to hear back within a few days. But if I had the confidence to open it myself, I was sure it would be fixed with a good clean.
Anyway, thanks for crystallizing all this into a post. Thanked!
THANK YOU SO MUCH FOR THE INFO. i have had so much trouble with unresponsive screen after installing typhoon 2.6.3 and it from holding down the red button all the time for install and the past millions times for everything else.
Thanks for the heads up
Sent from my HD2 using XDA App
U maybe be right about why this issue happens but if u rely on other key then will also wear out soon ...
What I did is I remapped my volume up n down keys to power and back button which I believe are the most used in android and then found a app to manage my volume in android that way I don't lose my sound on rhw phone
Also I went ahead and got a another app which places virtual buttons on ur screen so u can use then instead of the actual hardware buttons
For button remapping
get the BUTTONREMAPPER for android and for on screen android buttons get BUTTON SAVIOR
hope this helps
Sent from my HTC HD2 using XDA App
Good to know... will now wake my phone up with the green key as its hardly used in Android. Button Savior is a great app, been using it a while now. Took a bit to retrain myself to not use the back key.
Sent from my HD2 using XDA App
i'm going to agree with your hypothesis or at least suspect that dirt is probably a bigger factor than most people think in these cases. i just bought a non-responsive phone today and while i stuck my nail (yes, i should probably clip them) around the edge, in between the screen and housing, i was surprised to see just how much dirt was in between that crack. same with the area around the buttons; there's a lot of grime there.
since i just got the phone i haven't even opened it up but the first thing i'm planning to do is give it a good interior clean around the buttons for sure as that seems to be the sensitive spot. touch screen devices are very delicate and the micro particles of dirt which build up over time probably create a hazard that people really don't really anticipate. compound that with having to mash on those buttons all the time probably crams the debris in there even tighter.
i'll attempt to clean and check the contact as you suggested and will report back if it helped in my case.
About hardware keys:
I don't use them at all, only for wake up the phone (it can be wake up with any key)
There is an app in market called "button saviour" it's just excellent app to keep your hardware keys for a long time
AngelDeath said:
The problem is HARDWARE, The Culprit: THE END KEY (Red Button)! The Answer to "How or Why": The "End" key is used to turn the phone on and off or to put it in sleep mode, it is the most used key out of all 5 keys, it is used probably 7x more then all the rest, Its used for just about everything, now how does this cause the unresponsive screen? Easy, the phone lock or sleep is associated with this key, Its the only way to make the screen go off other then waiting for the time out period. Because by habit we mostly hit the end key to turn the screen off the phone automatically associates this with locking the phone, once that happens the screen becomes unresponsive because of several reasons: 1) The contact under the actual key has dirt which causes the button to stick in the down position, 2) the contact is bent which the "end" key is pressing down on the contact which is making contact with the board and causing it to be unresponsive, 3) The contact is worn. This is the reason why if you press the end key a few times (anywhere between 2-10) and then try the screen responds, this is cause your "unsticking" the key which then lets the screen respond.
Most of us when we hit the end key press to the far right to avoid hitting the back key (The button with the left arrow) which causes the end button to lean toward the right. But you can wake the phone up with the other 4 keys to the lock screen which will allow you to unlock the phone. As a temporary fix for myself, on my test phone I now make sure to press on the left side of the key to prevent this from happening, since its a test phone I'm not worried, but the real solution is to take the phone apart and clean the underside of the end button, and the actual contact with alcohol to remove the build up of dirt and whatever else. And also if the contact frame is bent to GENTLY bend the right side back up alittle to stop it from happening, or sending it to htc and letting them fix it.
We have to RE-TRAIN ourselves to start using the other keys to wake the phone up and not rely on the end key so much.
Hope this helps anyone finally why we have this problem. And if it works for you then hit the Thanks button
Click to expand...
Click to collapse
You just hit d nail on d head pal...My HD2's touchscreen also stopped responding and nothing i did (software-wise) worked...i flashed several WinMo ROMs and Android builds with no luck, till i read somewhere online dat some guy seemed 2 solve his touchscreen issues by installing "CleanRam", ran a level 3 clean up (use MyMobiler for this) and by pressing real hard on the red end key button..I did just dat and voila it works!!
I have a Tmobile HD2 which is no longer covered under warranty and i'm not willing 2 part with almost $200 here 2 have d whole lcd & digitizer replaced...I recollected dat in d forum i read the suggestion from, a lot of ppl came n posed their views on why it's not possible but i tell u it is cuz it worked for me..Nw i'm comfortably dual-booting WinMo & Android via sd. i use "button savior" and "extended control" to navigate and power down/reboot respectively.
Hweva i believe its not a permanent fix as it simply refuses 2 allow me run android full-time thru MAGLDR, & i think i know y..pressing down on d end button 2 launch MAGLDR/CWR options after install messes up d connection with d digitizer underneath and d touch screen thereby causing it 2 fail again when android boots up....I just might try opening it up myself n cleaning dat area up as u suggest but dat'll be when my current fix fails cuz as d saying goes "If it aint broken? then don't fix it"
Just installed Button Remapper, and not to sound like an idiot, but can someone tell me which one I would have to remap to make the volume up key or down key to put the phone to sleep and wake it up, and would that still be able to use the volume key to turn up and down the volume as well?
AngelDeath said:
Just installed Button Remapper, and not to sound like an idiot, but can someone tell me which one I would have to remap to make the volume up key or down key to put the phone to sleep and wake it up, and would that still be able to use the volume key to turn up and down the volume as well?
Click to expand...
Click to collapse
Hmm...i don't use d app but from wat i can gather on d dev's thread, you would have 2 remap ur volume keys to "Power"...Also checkout dis review 2 learn hw 2 mk d remapped button work even in sleep-mode.
I can agree but mine's been in twice on repairs with the same error but screen was replaced both times amongst the digitizer, backcover (Can't understand why) and 3 other things were replaced. Buttons weren't replaced.
CaCtuZ123 said:
I can agree but mine's been in twice on repairs with the same error but screen was replaced both times amongst the digitizer, backcover (Can't understand why) and 3 other things were replaced. Buttons weren't replaced.
Click to expand...
Click to collapse
If I'm to base how the HD2 is setup internally, they wouldnt replace the buttons, they would replace the contact or contact board under the buttons, remember the buttons are like a keyboard, they dont wear out, its what they push on that gets dirty or worn.
I was traveling and this happen t me and became desperate.
Following the instructions I come to the clear conclusion that our HD2 has this hardware problem.
If I do not use the end call button no issues with the screen, really, no issues.
Hope my feedback will be helpfull as well. Great job done here!
pauloviegas said:
I was traveling and this happen t me and became desperate.
Following the instructions I come to the clear conclusion that our HD2 has this hardware problem.
If I do not use the end call button no issues with the screen, really, no issues.
Hope my feedback will be helpfull as well. Great job done here!
Click to expand...
Click to collapse
Yeah HTC screwed up on dat...its just as said,1 has 2 be careful n avoid using d red end key button as much as possible 2 enable d device last much longer...And if u do ave 2 use it, press on d left-most part of d key (closer 2 d back arrow button) to get d job done.
I just had this issue happen to me and thought it was my build... But I found another way, I use Cyanogen Mod 7, and in the drag down menu (from the top) I added a sleep option, because thats the only thing I use it for... and I never have a reason to press the end button now.
This is the best thing I have found to fix it without having to remap the buttons
I guess I'm lucky because I have never had a problem with the responsiveness of the touchscreen and/or end button. I got my HD2 a month before TMO release date and trust me it has been thru alot (scratches all over, even a piece of glass missing next to the call button). So my question is how much pressure and wear 'n' tear are you all putting on your end button or phone for that matter?
big3d said:
I just had this issue happen to me and thought it was my build... But I found another way, I use Cyanogen Mod 7, and in the drag down menu (from the top) I added a sleep option, because thats the only thing I use it for... and I never have a reason to press the end button now.
This is the best thing I have found to fix it without having to remap the buttons
Click to expand...
Click to collapse
Can that be done with other roms? And wouldnt a shortcut or a widget on the main screen also work?
on1ydabest said:
I guess I'm lucky because I have never had a problem with the responsiveness of the touchscreen and/or end button. I got my HD2 a month before TMO release date and trust me it has been thru alot (scratches all over, even a piece of glass missing next to the call button). So my question is how much pressure and wear 'n' tear are you all putting on your end button or phone for that matter?
Click to expand...
Click to collapse
It all depends really Understand that not all HD2's go thru the same testing process when it comes out of the manufacturer. Also take into consideration that it also depends on how often you flash a rom, if your flashing a rom every day or every week expect that you will shorten the life of the end button, also it doesnt always mean that the button is bad, it could clearly be dirt underneath that could also be causing the issue. And I said the same thing when I saw posts about people saying that android killed their screen. I even responded to it but always maintained it was hardware, even though I didn have the problem, and I bought both my HD2's used in Dec. and the day it happened and I found out why I posted this, if I was to guess, I would say that I probably flashed both my HD2's close to 200 times with different roms, or upgrades, or testing fixes out.
So if your not a flash nut, then your probably safe. There are many factors that can play a role in the end button life cycle, And no two people use their HD2's the exact same way.
the non-responsive touchscreen problem happened to me this morning. I woke up trying to unlock my phone only to find that it would not respond to any touch gestures. I was however able to uninstall HSPL and Flash the stock WM6.5 rom since I was going to T-Mobile to get a replacement. When I took it to T-Mobile the employee resetted the phone by holding the 2 volume buttons and the power button then somehow the touchscreen started to respond to touch again. I was completely puzzled as I thought it was for sure a hardware problem. But now I'm going to flash Android and hopefully the problem will not arise again, if it does, back to T-Mobile I'll go!
What Android really needs is some sort of "X" button, or even a widget on the main screen that you can just tap and put it to sleep. The three most keys used in my opinion is the windows key (Apps that use it for a menu), the back key (Since there is no damn close button), and the end key (sleep, flashing, booting to magdlr).
Some one had a concept here of buttons that looked very similar to The desire HD, the greatest thing would be if someone could make the bottom of the htc sense (app drawer, phone, and the personalize) auto hide and have the desire HD buttons come up with a power button at the end and this way if you hit menu it would bring up the original 3 button screen.

Cyanogenmod 7 / power button issues

Pressing the power button a few times to get to the unlock screen automatically reboots the phone. A few times because with the case I have it is somewhat difficult to get it right everytime. This doesn't happens every time but I do face this once a day. Anybody else has the same problem??
Cheers!
Hello,
I have the same problem as you. If someone in the solution ... thank you
Well the answer seems to be:
1. Press the power button right
2. Get a new casing probably the one with kickstand from HTC
Its the casing probably. Haven't tested. But the HTC casing comes with well cut design non obstructive.
Sent from my Desire HD using XDA App
I really don't see this as a problem. It happens to me from time to time also, not many times though. But usually because I've been clicking it in my pocket "accidentally" when I'm taking the phone out of my pocket. Just take it as a feature

Back Button Problem

This might be a relatively small problem but it can be a little annoying. The back button (right side of the menu button) seems to be a little less responsive and 'smaller' than the options button (left side of the menu button).
By smaller I mean I need to click it exactly at the right spot and the button reponsive 'area' seems to be very small compare to option button which seems to take up most of the left side allocated to it.
I am not sure if this is intented or some kind of software/hardware fault?
I read about upgrading touchpad firmware through *#*#2663#*#* but there are reports than this could brake the buttons completly.
If anyone has any information it will be greatly appreciated.
P.S phone is not rooted and I bought it from vodafone Ireland.
there are a few threads on the hardware buttons not working correctly try the search.
I found one about the back button, not a lot of info though.
http://forum.xda-developers.com/showthread.php?t=1057348&highlight=button
I have the same issue but also to another extent. Mine has an issue where sometimes it will double tap when I only press it once. This can get annoying. I do have a screen protector on and I'm not sure if that has anything to do with it.
Same thing happens to me ... but Its kinda rare(I am not using a screen protector). Does anyone know a solution? should updating firmware fix this?
I am thinking about asking for a replacement.
Replace it, same problem with my first unit, 20% of the presses didn't register
Sent from my GT-I9100 using XDA App
nomnompie said:
I have the same issue but also to another extent. Mine has an issue where sometimes it will double tap when I only press it once. This can get annoying. I do have a screen protector on and I'm not sure if that has anything to do with it.
Click to expand...
Click to collapse
I thought it was just me with the double tap when i press it once lol. Grrr its annoying man! :[email protected]
Sent from my GT-I9100 using XDA Premium App
So the only way to fix it is to replace it?
I would imagine someone can make a mod to the touchkeys for like a certain millisecond delay between presses to fix the double tap. People have patched hardware keyboards for stuff similar to that.
As far as the non-registering presses, that might have something to do with delay too. A smart developer would have to try and look at it though I'm just guessing here.
I haven't noticed the non-registered presses in a while, not sure if it went away with a new kernel or if I just got used to how to press it to make it work. The double tap happens more often to me now lol.
Happened to me on my first unit, back button was only responding about 50-60% of the time, on the 2nd phone back button was extremely sensitive ( as sensitive as the SAMOLED screen which is a huge plus) 3rd phone seems "normal"
Galaxy S2 back button getting pressed twice on a single press.
When I am in 2nd/3rd level screen of an app, back and menu button lights go off(but screen is on). While pressing back button sometimes it's going back 2 levels with one, single press! As if I have pressed it twice. It doesn't happen always though.
Is there any fix for this?
PS: I am using a screen protector. Will remove it and see if that's the culprit or not.
u shud b thankful mate..my home butoon stopped responding at all
Hi,
Sorry to hear that.
But how did it happen? And how old is your phone? It must be still under warranty. Did you try taking it to the service center?
Back button problem sgs 2
I was also having this annoying problem.....searched over XDA....and found some tricky (fishy) codes for updating touch firmware.....which may end up braking those keys....so i stayed away from those tricks..
i googled again and found one method which finally worked for me
To get sgs2 into sleep use power button...nd for waking up use home (centre) button...this worked for me
SGS 2/XWKF3/CF root
Odp: Back Button Problem
Sorry for digging it up. I have the same issue, sometimes back button is acting like it was tapped twice. Is there any sofware solution instead of replace any parts?
Wysyłane z mojego GT-I9100 za pomocą Tapatalk 2
i had the same promblem and a full wipe did the job

Categories

Resources