Help P1000JPJM4 - Galaxy Tab General

I flashed the new Samfirmware Arabic Rom P1000JPJM4 as described....
The device Reboot with Samsung Logo and Vibrate.
I tried several times with no hope.
Any Help please.....?

boot into recovery and wipe data and cache partions.. should do the trick.

Done several times still have same problem.
Any other suggestion?
Thanks

Roufosso said:
Done several times still have same problem.
Any other suggestion?
Thanks
Click to expand...
Click to collapse
Do these steps carefully:-
1- Reboot into Recovery (Press Power + Vol Down )constantly
2- Start Odin 1.7 , load P1 and choose Repartition
3- DO NOT LOAD ANY THING ELSE
3- Connect Device to PC, wait for connection establishment then press start
4- the device will be restarted
5- Reboot into Recovery (Press Power + Vol Down )constantly
6- Start Odin 1.7 , CHOOSE REPARTITION , DoNot Load PIT
7- Load your ROM tar file as PDA
8- Connect Device to PC, wait for connection establishment then press start
9- wait for device to be flashed, rebooted
10- if a FAILED RED ALERT at the end of flashing process....just Disconnect and Restart
B.R.

Galaxyer said:
Do these steps carefully:-
1- Reboot into Recovery (Press Power + Vol Down )constantly
2- Start Odin 1.7 , load P1 and choose Repartition
3- DO NOT LOAD ANY THING ELSE
3- Connect Device to PC, wait for connection establishment then press start
4- the device will be restarted
5- Reboot into Recovery (Press Power + Vol Down )constantly
6- Start Odin 1.7 , CHOOSE REPARTITION , DoNot Load PIT
7- Load your ROM tar file as PDA
8- Connect Device to PC, wait for connection establishment then press start
9- wait for device to be flashed, rebooted
10- if a FAILED RED ALERT at the end of flashing process....just Disconnect and Restart
B.R.
Click to expand...
Click to collapse
Thanks for your advice that I followed as mentioned.
Regarding Odin process is completed successfully then the device reboot to recovery mode so I rebooted again. Unfortunately the problem is still unsolved.
Vibrate on Samsung Logo.
Other advice may can help.?
Thanks and Best Regards,

I had the same problem with you. I own an Euro version Tab and I flashed P1000JPJM4 (I didn't know that it is arabic) and had the same symptoms after that.
I believe that P1000JPJM4 have signed kernel just like P1000XXJM* series.
I tried to flash P1000BUJI4 which was my previous version but I got errors in odin.
I flashed P1000XXJM6 which also has signed kernel and my tab come to life.
After that I did the roto patch to unsign kernel (May RotoHammer and everyone helped the patch project, live long and happy!!!!) and after that I flashed P1000BUJI4 with success.

can you poat a link to roto patch please.

flash this rom with odin 1.7 select re-partition no pit file
http://www.multiupload.com/O1RQ6NMVAP
Pass:ce4arab.com
Its P1000JPJM4 put contain dbdata.rfs
Im sure it will solve your problem

Roufosso said:
can you poat a link to roto patch please.
Click to expand...
Click to collapse
hi,
its in the stickies in this forum.
anyway, here it is
read the first post.
regards,
mike

dude i flashed this rome and nothing worked to fix it... i took to samsung and told them this happened after an update through kies and they almost gave up hope of fixing it, however, they flashed a rom as a last resort and it worked! and it is amazing and blazing fast but i wasnt able to find it online... its P1000JXJM2 good luck

@al-motamel :
I have NO words to thank you, begad enta ra'e3, teslam eidak.
Garrabt kol haga momkena fe kol makan, bas hallak howwa el wahid elly Zabat el gehaz.
shokran begad.
Wael

I've flashed my AT&T Galaxy tab.
I've run the whole process described in a video at Galaxy Tab forum and everything went well, except the last boot (JHA.tar, P1_20100909.pit and Roto-JMA.tar
At the final booting with the new firmware, the screen is black. Only the AT&T logo flashes for a second
I have no option to go to the recovery mode. The Samsung logo does not appear also. When power it on, it seems to be working but the screen is black (I've hear the jingles and the vibs of a "normal" boot)
I've rooted the tab before to be able to run the "bootloader application" from Roto (which told me I'm safe).
Do you have any suggestion on what to try?
Thanks in advance.
Kiko

I've fixed the black screen problem just loading the JJ4 bootloaders.
I've searched on XDA and follow the suggestion from ROTO.
It is now working perfect.
MIllion thanks to Ayman07 for your easy to follow guide and also to ROTO for his suggested fix o fthe problem.
Kikobarcelona

Related

[Q] Galaxy Tab hangs on Galaxy Tab Logo after firmware upgrade

Hello, I have upgraded my galaxy tab (pda jj3-phone jid - csc jj2) to roto jmi firmware with odin 1.7. all the process seems to be ok, no error message.
After rebooting, the device hangs on galaxy tab samsung logo. factory reset is no longer possible. Does anybody have a idea?
Many thanks in advance.
ZK
Ever heard of "if it ain't broke dont fix it"? So, there you go
sure... sure but now it is
Try using volume UP rocker + power button.
This should put the phone into recovery.. Then you select reset to factory defaults. That should do the trick.
thx kragebein, unfortunately my device won't to go in recovery mode
Are you sure you are doing it right? Hold down the up volume rocker and the power button at the same time until you hit the recovery screen? Optionally you could try to see if you get it in download mode, and reflash your phone.. i had severe problems with mine, but got it fixed today by using roto-jma rom..
Sent from my GT-P1000 using XDA App
Yes, I think I dit it right. Download mode can be activated with volume down & power, but not recovery mode with volume up & power. I have tried to load the firmware again without any error message, but no way.
zolakero said:
Yes, I think I dit it right. Download mode can be activated with volume down & power, but not recovery mode with volume up & power. I have tried to load the firmware again without any error message, but no way.
Click to expand...
Click to collapse
Same here. Whatever I do (flash) I don't get past the Samsung Boot screen.
zolakero said:
Hello, I have upgraded my galaxy tab (pda jj3-phone jid - csc jj2) to roto jmi firmware with odin 1.7. all the process seems to be ok, no error message.
After rebooting, the device hangs on galaxy tab samsung logo. factory reset is no longer possible. Does anybody have a idea?
Many thanks in advance.
ZK
Click to expand...
Click to collapse
You need to flash a complete rom, like Roto JME FULL v.4 with the tab in download mode. He gives complete instructions.
Some releases are just upgrades, so start with a complete rom.
rangercaptain said:
You need to flash a complete rom, like Roto JME FULL v.4 with the tab in download mode. He gives complete instructions.
Some releases are just upgrades, so start with a complete rom.
Click to expand...
Click to collapse
I have tried that and either it fails to upload the primary bootloader (boot.bin) or it stays the same after flashing: it doesn't go beyond the first Samsung Screen. No adb connection possible.
How can I flash a primary bootloader without protection? With JTAG only?
A forum member, Rotohammer used a Jtag box to fix the bootloader issue. He doesn't recieve PM's, but someone he collaborated with to solve the bootloader issue is a fellow named Chainfire. Perhaps you can contact him for the procedure.
But when you flashed the JME did you use the hidden .pit file with repartition selected?
If I was in your spot I would
1. turn off the tab (push power button for 10 sec)
2. then push power and volume down to go to download (yellow digger screen or phone and pc screen)
3. Connect to pc with odin3 already opened, wait until the yellow box shows the connection
4. Load the p1_hidden.pit and check repartition
5. Flash that, then power off, go into DL again, load and flash JME v4 full rom
6. Now flash a modem
hi guys im thinking that u guys may have flash a lock bootloader rom
or u actually already have a lock bootloader rom
try load a roto jme v4 full version see if it works~
1. download odin 1.7
2. download Addon-JME-Modem.zip / P1_add_hidden.pit / Roto-JME-Full-v4.zip from http://files.deodexed.com/ModADroid-Galaxy-Tablet/Rotohammer/JME/
3. and follow the instruction here http://forum.xda-developers.com/showthread.php?t=895827
I wish i said that.
zolakero said:
Yes, I think I dit it right. Download mode can be activated with volume down & power, but not recovery mode with volume up & power. I have tried to load the firmware again without any error message, but no way.
Click to expand...
Click to collapse
It is there u just cant see it. Try to flash jj4 bootloader and see if u could go to recovery mode
Sent from my SGH-I987 using XDA App
The bootloader mentioned above is in a thread about the black screen and white line you are experiencing. It has the link to that jj4 file.
rangercaptain said:
But when you flashed the JME did you use the hidden .pit file with repartition selected?
Click to expand...
Click to collapse
Thanks, but this didn't help. I think it may be a hardware issue (e.g. the kernel can't be loaded, panic or something). I will return my tab tomorrow.

WILL PAY $30 to anyone that fixes my Verizon Galaxy Tab!!!

I recently purchased an off contract Verizon Tab from a friend.
I had successfully rooted it using the superoneclick.exe file.
I since decided to flash Overcome_v1.2.1 with Odin using the exact steps as listed & even watched the video 2x.
"Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button)."
Now...I don't know what "quite a long time" is but after 30mins, there was still nothing but a blank sceen w the tell tale sign of a light, thin, margin type as seen on the video.
I then followed these steps:
"IF your Tab does not boot after flashing the kernel and hangs at the Samsung Galaxy Tab screen, you must follow the following procedure
1.Get a stock rom package (any of Rotohammer's firmwares will work)
2.Get P1_add_hidden.zip attached to this post and extract the P1_add_hidden.pit file
3.Using Odin 1.7, put stock rom (Roto-JME-Full-v4.tar for example) in PDA slot.
4.Put P1_add_hidden.pit in Pit slot
5.Check repartition box
6.Put Tab in download mode by holding Volume Down and Power, connect to the computer, and press start.
7.After this, the Tab will reboot normally. Shut it down and return to download mode.
8.Open Odin 1.7 and reconnect the Tab.
9.In the PDA slot, choose the Overcome Kernel v2.0 tar file for use with Odin. Press start
10.It will flash the kernel then reboot. Upon reboot, you should hear the sexy robot voices informing you of the status of the EXT4 conversion.
11.Once done, the Tab will boot normally. At this point you can load Overcome v1.2.2 rom (or any other Rom of your choosing)
12.NOTE - Overcome 1.2.2 includes v2.0 of the kernel, so no reflashing is required after install."
I never got past the part in step 10 to hear any responses. And instead of searching for one of Rotohammers FIRMWARES as suggested, I input a kernel from Voodoo!
Now I can STIL get into DL mode but whenever I try a normal reboot or recovery, it runs through -Wiping DATA- Formatting DATA---DATA: Wipe failed!
over and over until the Tab reboots and when the samsung splash screen somes up, there is a weird "flashing" of the screen in multiple colors.
PLEASE...for God's sake...with all the great inds on here, someone help me!
Please email me @ [email protected] or call/txt me on my GV # 401-213-9555 I will PayPal or Wire someone a "service charge" for their assistance!
Thank you & I hope i did not break any rules on here by asking.
You need to find a stock Verizon firmware and flash through Odin
I just did a brief search and found this: http://forum.xda-developers.com/showthread.php?t=855415
But I'd ultimately recommend flashing this: http://forum.xda-developers.com/showthread.php?t=941749
And you may need to flash this to get to a stage where you have a working recovery image: http://forum.xda-developers.com/showthread.php?t=941781
Hope this helps
TheGrammarFreak said:
You need to find a stock Verizon firmware and flash through Odin
I just did a brief search and found this: http://forum.xda-developers.com/showthread.php?t=855415
But I'd ultimately recommend flashing this: http://forum.xda-developers.com/showthread.php?t=941749
And you may need to flash this to get to a stage where you have a working recovery image: http://forum.xda-developers.com/showthread.php?t=941781
Hope this helps
Click to expand...
Click to collapse
Thank you very much! I will attempt that. I seem to be stuck in DL mode though.
I was downloading in Odin and the Tab has been stuck at 95% for the past 30mins.
Should I power off or is it a sure fire way to brick it?
dvargas72 said:
Thank you very much! I will attempt that. I seem to be stuck in DL mode though.
I was downloading in Odin and the Tab has been stuck at 95% for the past 30mins.
Should I power off or is it a sure fire way to brick it?
Click to expand...
Click to collapse
Assuming there are no bootloaders being flashed you can't really make it un-recoverable. What exactly were you flashing?
Sent from my GT-P1000 using XDA App
Originally? Just the overcome_v1.2.1 kernal.
dvargas72 said:
Originally? Just the overcome_v1.2.1 kernal.
Click to expand...
Click to collapse
Kill the the current Odin flash. Then flash the k-lean kernel. Reboot into recovery. Flash k-lean ROM
Sorted
Sent from my GT-P1000 using XDA App
I want that money!
From the Tab.
www.twitter.com/ayman07
LOL...Get this working for me! My patience is wearing thin now..lol.
But if the advice from The Freak, he earned it
Any idea why it keeps getting hung up right about 99%?
hi
hi friend
i had simmilar problems in past.
Maybe you have problems with the usb ports of your machine.
If you have amd/sis/via for usb chipset at your computer try to do the procedure with another machine with intel chipset.
I hope this helps you
dvargas72 said:
Any idea why it keeps getting hung up right about 99%?
Click to expand...
Click to collapse
Its getting stuck there because you're flashing a GSM ROM to a CDMA Tab
Sent from my GT-P1000 using XDA App
PM me and ill guide u step by step. send me a friends request.

How to Re-stock P1000 to Gingebread 2.3 | Guide with Links

NOTE : this is not my own procedure but i just wanna share this with you guys since some tab users here are having problems restocking their tab to gingerbread, i have also added some notes and troubleshooting in case there will be an issue flashing the rom
link to the original post credits of course to the writer > how to restock p1000 to gingerbread 2.3
btw, this is a complete and full tutorial/step-by-step guide on how to restock gingerbread rom, so if you did not download all requirements, restocking wont be successful
my story and experience : hey guys, yesterday night, i softbricked my galaxy tab p1000 which was running cm9, it turned out like that when i went to recovery and wipe all data, cache, dalvik, even system, and boot. i tried reflashing the cm9.zip but as it was installing its update, my tab suddenly boot into battery icon, meaning it was already empty (maybe, dont have any idea), then, since it was already 12 midnight, there were no internet cafes open in our village, so i went out though somehow it might be dangerous for me, then, i found an internet cafe open. i rent a pc, first, i tried to go to download mode, so some drivers will be installed, but it kept showing "unkown device recognized" bla bla.. still.. i didnt lose hope. so i searched on google, and i found this site > http://suzhipackz.blogspot.com/2012/07/how-to-re-stock-samsung-galaxy-tab.html , when i finished downloading odin, i opened it to check whether it will read my device or not, first three attempts, it did not. so, i thought of downloading samsung kies so the drivers will be installed (safest way really to install samsung drivers), then i still looked for a smaller file (while waiting for kies to complete its download), then i found that there is a smaller zip file for you to install samsung drivers (see attachment below), i installed it, but still odin cant detect my device (try it, might be just on the pc i rented), so i just waited for kies to complete.. after a couple of minutes, successfully downloaded kies, and installed it. i tried connecting tab to pc with odin opened, i rebooted to download mode again and reconnect tab to pc, and voila! odin read my device! so, since pc has already detected my device, i just waited about 1 1/2 hours for the rom and the pit file and the db data file.... after almost 2 and half hours of crossing fingers, i have revived my tab and restocked it to gingebread 2.3!
HOW TO RESTOCK SAMSUNG GALAXY TAB p1000 to 2.3.3 GINGER BREAD STOCK ROM?
HERE:
- ALL REQUIREMENTS
.......Samsung KIES > LINK FOR SAMSUNG KIES
.......ODIN3 v1.7 > LINK FOR ODIN3 v1.7
.......p1000xxjq1_p1000xxjq1_p1000xxjpz < THIS IS STOCK ROM > LINK FOR STOCK ROM
.......gt-p1000_mr_PIT > LINK FOR PIT
.......dbdata.zip > LINK FOR DBDATA
.......place it all in ONE FOLDER in desktop "unzip it all"
PLEASE DOWNLOAD ALL OF THIS BEFORE YOU CONTINUE..............
PROCEDURE:
.......Turn off tab
.......open ODIN3 v1.7
.......click on the PDA and select - p1000xxjq1_p1000xxjq1_p1000xxjpz in your computer
.......clink on the PIT and select - gt-p1000_mr_PIT
.......Check only RE-PARTITION, "uncheck auto reboot and f.reset time"
.......in your tab press and hold "VOLUME DOWN AND POWER BUTTON"
.......if DOWNLOADING APPEAR leave it like that
.......now, connect you tab in computer
.......if ODIN detects your phone PRESS START in ODIN
.......wait for it until success, after that disconnect your tab
(if for an instance it stuck on downloading mode but you have already finished flashing, do not worry, you just have to manually hold the power button for it to boot up, it might get into recovery, so please reboot the system (it might also be a touch recovery so please tab the home touch key to continue) then if it keeps on booting on "samsung", do not worry, you are not done yet with the restocking procedure, so please proceed to the next step)
.......press and hold power button until it will turn off
.......open ODIN3 v1.7 again
.......UNCHECK it all "re-partition, auto reboot, f.reset time"
.......click on the PDA and select dbdata.zip
.......press and hold "VOLUME DOWN AND POWER BUTTON" again
.......if DOWNLOADING APPEAR leave it like that
.......now, connect your tab again
.......if ODIN detects your phone PRESS START in ODIN
.......wait for it until success, after that disconnect your tab
(again, if it is stuck on downloading mode but you have successfully done the flashing, hold power key to turn the tab on, and if it keeps on booting to "samsung" again, do the next step)
.......This time we will go to CLOCKWORKMOD by holding "VOLUME UP and POWER BUTTON"
(then wipe data, and wipe cache, (volume keys to scroll up or down, and home touch key to select) and reboot system, wait for a minute or two and home screen will now appear)
.........................................NOW YOUR IN STOCK ROM AGAIN 2.3.3 GINGER BREAD
another note : when there is an error for example that flashed on your tab screen like a color red "E:\ " something like that, do not worry, it is the external sd card (i dont have one so it was an error then but not a problem, no worries) just let it be, wait until it finishes
some files are already attached below coz they are just small in size
clicking "thanks" button is enough for me..
just sharing this with you guys...
happy restocking!! :laugh:
Update Prob
mastersymvts said:
I want get full file samsung tab p1000. For flash my tab.. Tq
Click to expand...
Click to collapse
Hi Guys is crashed my tab.
i get it functional with the stock rom 2.3.6
P1000XXJPZ
Kernel 2.6.35.7
[email protected]#2
Build gingerbread.XWJQ8
i wantetd to Flash to a newer rom but noting worked any ideas?
I modified a couple years ago the tab to include the sd space as System space. I do Not rember how i did this....?
If i get throught the stock partion all would be find but i couldn´t.
Regular mod Installation doesnt work, rooting also isn´t possible ...
readin with Heimdall shows this message
Initialising connection...
Detecting device...
ERROR: Failed to access device. libusb error: -12
I hope you guys have any ideas.
Greets
P1000XXJQ1_P1000XXJQ1_P1000XXJPZ.zip do you stil have this?
Hotfile is down
Stock Rom's Link doesn't work
So, I tried your recipe and it worked pretty well for me, but the annoying thing about it was the links to the Stock Rom, so i got the below link as a mirror for those who are interested.
p1000xxjq1_p1000xxjq1_p1000xxjpz < THIS IS STOCK ROM >h-t-t-p-:-/-/-f-i-l-e-s-c-r-o-p-t-u-b-e-.-c-o-m/file/7806957-p1000xxjq1-rar
Couldn't find the given URL
LeMasoud said:
So, I tried your recipe and it worked pretty well for me, but the annoying thing about it was the links to the Stock Rom, so i got the below link as a mirror for those who are interested.
p1000xxjq1_p1000xxjq1_p1000xxjpz < THIS IS STOCK ROM >h-t-t-p-:-/-/-f-i-l-e-s-c-r-o-p-t-u-b-e-.-c-o-m/file/7806957-p1000xxjq1-rar
Click to expand...
Click to collapse
I couldn't locate the file.
need new links. prefer putlocker/mediafire etc.
THKS a Lot!!!!
Great!! many thanks my p1000 have a second life
http://www.4shared.com/get/B-DeOju6/P1000XXJQ1.html here you go its a miracle what using google could do using the right search methods if you would thanks i would really apreciete it guys and gals.
I just flashed my tab stock 2.3.6 from cm11 using odin. But stuck in bootloop. After going to recovery i get error message (red) as in pic. Where did i go wrong?
Thank you for this and sorry for reviving an old thread. It sucks when links go dead (or offer that sketchy ilivid crap). Here is a mirror:
Mirror for samsung galaxy tab P1000 stock odin TAR: stock-P1000XXJQ1_P1000XXJQ1_P1000XXJPZ_HOME.tar
https://mega.co.nz/#!7wohlbKT!i3K7lvIfombRdJEzUUP-fiIZQS1qeStOr16tty-T86w
And a mirror to download ODIN 3 v 1.85: odin3-v1.85.zip
https://mega.co.nz/#!W553iL7B!vZTVktUwwg35a_glWGgBEaIDg11JVgkvFZ94mpzECas
2.3...
I think that there was a couple of kernel and Android security flaws in Linux 2.6, not fixed by Samsung Electronics Co. Ltd..
Samsung Tab P1000 stuck in nowhere!
First of all thanks the OP for the brilliant post on how to re-stock GB on P1000.
Earlier today I was fooling around with my P1000 to update it from CM11 to Omnirom 5.0.2, troubles started there. I was trying to install the TWRP recovery over CWM, and that is when all hell broke loose.
1. P1000 couldn't mount my internal SD. The tab was perfectly booting to a previous version of JB CM sapir, which I don't have any clue appeared where from. The storage showed the 2 GB internal memory, but the 12GB internal SD was missing out.
And the CWM errors were E:/can't mound internal SD
2. Now, after wiping data, dalvik, battery stats, formatting and all that, the tab doesn't even boot into the OS. The moment the power button is on, CWM initiates a count down saying, trying to mount SD, but unable to do so. After 20 seconds, the tab starts this whole process again, and thus a loop.
3. I tried to re-stock to GB; but my tab isn't being detected by Odin in download mode. Odin detects the tab when it is turned on and when the tab is on countdown-restart-countdown loop; but not in download mode.
I am a total noob, and I don't want to throw my tab away as I am a student and can't afford to get a new one Someone please help me to fix the issue. Thanks in advance!
PolaritySwitch said:
First of all thanks the OP for the brilliant post on how to re-stock GB on P1000.
Earlier today I was fooling around with my P1000 to update it from CM11 to Omnirom 5.0.2, troubles started there. I was trying to install the TWRP recovery over CWM, and that is when all hell broke loose.
1. P1000 couldn't mount my internal SD. The tab was perfectly booting to a previous version of JB CM sapir, which I don't have any clue appeared where from. The storage showed the 2 GB internal memory, but the 12GB internal SD was missing out.
And the CWM errors were E:/can't mound internal SD
2. Now, after wiping data, dalvik, battery stats, formatting and all that, the tab doesn't even boot into the OS. The moment the power button is on, CWM initiates a count down saying, trying to mount SD, but unable to do so. After 20 seconds, the tab starts this whole process again, and thus a loop.
3. I tried to re-stock to GB; but my tab isn't being detected by Odin in download mode. Odin detects the tab when it is turned on and when the tab is on countdown-restart-countdown loop; but not in download mode.
I am a total noob, and I don't want to throw my tab away as I am a student and can't afford to get a new one Someone please help me to fix the issue. Thanks in advance!
Click to expand...
Click to collapse
Can you flash at least the PIT in countdown mode(after you flashed the PIT, it goes to download mode)
Flash during countdown...
black_blob said:
Can you flash at least the PIT in countdown mode(after you flashed the PIT, it goes to download mode)
Click to expand...
Click to collapse
Thank you! I tried doing that. On the success/failure counter on Odin, it shows as a failure
PolaritySwitch said:
Thank you! I tried doing that. On the success/failure counter on Odin, it shows as a failure
Click to expand...
Click to collapse
Can you try booting the Vol- or the Vol+ button until you see the flashscreen?
Weird.(and making the tablet unbrickable needs a mod which I hope that you don't do)
black_blob said:
Can you flash at least the PIT in countdown mode(after you flashed the PIT, it goes to download mode)
Click to expand...
Click to collapse
black_blob said:
Can you try booting the Vol- or the Vol+ button until you see the flashscreen?
Weird.(and making the tablet unbrickable needs a mod which I hope that you don't do)
Click to expand...
Click to collapse
Well yes, Vol+ takes me to CWM recovery and Vol- takes me to download mode. Odin detects my Tab on CWM; I tried flashing the PIT which resulted in a failure. And on the download mode as I mentioned earlier, Odin doesn't detect my Tab
Well, I am all ears about the mod you're mentioning about, but let's just hope for now that I don't need that
PolaritySwitch said:
Well yes, Vol+ takes me to CWM recovery and Vol- takes me to download mode. Odin detects my Tab on CWM; I tried flashing the PIT which resulted in a failure. And on the download mode as I mentioned earlier, Odin doesn't detect my Tab
Well, I am all ears about the mod you're mentioning about, but let's just hope for now that I don't need that
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1312391
very Helpful
you Saved my life ... thank you veeeeeeeery much
Thanks for sharing this method. I quiet had a problem with the drivers and the link for them isn't available but I got a way to fix it. Thanks anyways.
Can you guys help me out with my p1000 tab too its bootlooped its in a stock recover and unrooted . I tried wiping data but nothing happens
thank you soo much

Boot Loop after installing a custom ROM

Hello..!!
I need some help here. I tried to flash a custom ROM (X-Note (build 6.0) for Galaxy S5 GM900F) and then flash a new bootloader, the problem is that my device will never pass the booting process. I was stuck with the logo and black screen. I have searched and tried tons of tutorials and fixes but have not solved it.
I even tried to wipe Dalvik cache, wipe data, format system. I even put out the battery and leave it for sometimes, then on but the problem is still there.
This link to bootloader that I downloaded and flashed using Odin (after successfully installing custom ROM) and also the instructions that I followed to install the custom ROM.
https://www.androidfilehost.com/?fid=23622183712475277
When I try to re-install stock Samsung via Odin, it shows a Fail message. I don't know where to go from here and I'm really worry that my phone will never come to work.
Please help me to solve it.
..
fffft said:
I'm too busy today to describe this in detail.. but here are a few comments that may help you.
First, it is fixable. Usually it's enough to boot to recovery mode (phone off, then press and hold home + volume up + power buttons). Then from the recovery mode menu, choose wipe system cache. Then reboot. If you still have an issue then try a system data format from the Settings menu (this will erase user files!).
And as a last resort, restore a backup (if you have one) or a full, stock firmware image with Odin or Heimdall. Odin is infamous for being a bit picky, so don't panic if you get a failed message. That happens to all of us. Look for a detailed Odin tutorial or how to flash back to stock firmware thread that has Odin tips e.g. use a different USB cable + USB port. Temporarily turn off anti virus on your PC.. If the Odin write fails, do not close the Odin window. Just pull the battery and USB cable from your phone again.. put the battery back.. go back to download mode (home + volume down + power), plug the USB cable back, then press the start button in Odin again. It's important that the Odin window was open the whole time.
It may take a few tries (Odin can be frustrating) but you'll succeed.
.
Click to expand...
Click to collapse
Thanks for your words, you give me some hope because I thought my phone is now useless. I'll try again as you said.

!HELP! my Grand 2 stuck at first boot screen :crying:

Hello guys I need your help plz for my new grand 2 phone
Phone model: Galaxy grand 2 sm-g7102.
Android: kitkat 4.4.2 ,rooted without using custom recovery.
I have rooted my grand 2 mobile using kingroot app without using any custom recovery
and it worked fine.
the problem started when I have installed Gltools 1.0.7 and give it root permission then my mobile screen turned off and mobile didn't respond.
then i do the following press volume up+home+power buttons and the mobile restart in recovery mod i press the first option
reboot system now and then screen stuck at first boot screen .
I wiped my data ,cache and factory reset and no benefit of that .
what i have to do plz help me
abbody said:
Hello guys I need your help plz for my new grand 2 phone
Phone model: Galaxy grand 2 sm-g7102.
Android: kitkat 4.4.2 ,rooted without using custom recovery.
I have rooted my grand 2 mobile using kingroot app without using any custom recovery
and it worked fine.
the problem started when I have installed Gltools 1.0.7 and give it root permission then my mobile screen turned off and mobile didn't respond.
then i do the following press volume up+home+power buttons and the mobile restart in recovery mod i press the first option
reboot system now and then screen stuck at first boot screen .
I wiped my data ,cache and factory reset and no benefit of that .
what i have to do plz help me
Click to expand...
Click to collapse
flash stock firmware.
go to sammobile.com
Search for grand 2 firmware
then download it.
The firmware must base on your country.
after that flash using odin.
after complete. Remove battery then insert it again.
go to recovery
wipe everything
then reboot system
wait about 10 minutes
congrats your phone is normal again
Solution to your problem:
You will need to download the NK1 version of kitkat 4.4.2 stock firmware.
1) install samsung kies or samsung usb drivers so that your PC will detect your phone.
2) Switchoff your phone first and put it in download mode by pressing volume down and home button and power button at the same time.
3) connect your phone to your PC through the usb cable and start odin. (The com port turns blue in odin which means phone is detected).
4) In odin, check the "Nand erase all" in the checkbox and then click on "AP" buttion and select the "G7102DDUBNK1_G7102ODDBNK1_G7102DDUBNK1_HOME.tar" file.
5) Click the start button and wait for 5 mins till the OS is installed.
6) After installation, on your phone it might show 'memory damaged' and 'erase memory'. Don't worry, nothing is damaged or serious, just click to reset and everything will be fine.
7) Done!
I have provided the NK1 version link to you from my google drive account:
https://drive.google.com/folderview...03NF9WUzJLTHVSVnkzWWN5aFVQSzVOS28&usp=sharing
(Please hit thanks if I helped you)
Thanks guys
Problem solved and it is working now :fingers-crossed:
I have this same problem and I downloaded the above file and followed the instructions accordingly, after flashing it is still stuck at REBOOTING TO RECOVERY for about one hour now.I guessing it might be related to hardware.
mbond said:
I have this same problem and I downloaded the above file and followed the instructions accordingly, after flashing it is still stuck at REBOOTING TO RECOVERY for about one hour now.I guessing it might be related to hardware.
Click to expand...
Click to collapse
Which firmware were you on before the first boot loop? Flash that firmware, and don't forget to pull the battery afterwards.
(Don't hit thanks, hit the phone on a pillow/bed of you think its hardware related).
abbody said:
Hello guys I need your help plz for my new grand 2 phone
Phone model: Galaxy grand 2 sm-g7102.
Android: kitkat 4.4.2 ,rooted without using custom recovery.
I have rooted my grand 2 mobile using kingroot app without using any custom recovery
and it worked fine.
the problem started when I have installed Gltools 1.0.7 and give it root permission then my mobile screen turned off and mobile didn't respond.
then i do the following press volume up+home+power buttons and the mobile restart in recovery mod i press the first option
reboot system now and then screen stuck at first boot screen .
I wiped my data ,cache and factory reset and no benefit of that .
what i have to do plz help me
Click to expand...
Click to collapse
For future!
Just flash compatible kernel
Press THANKZ
Shane_Picardo said:
Solution to your problem:
You will need to download the NK1 version of kitkat 4.4.2 stock firmware.
1) install samsung kies or samsung usb drivers so that your PC will detect your phone.
2) Switchoff your phone first and put it in download mode by pressing volume down and home button and power button at the same time.
3) connect your phone to your PC through the usb cable and start odin. (The com port turns blue in odin which means phone is detected).
4) In odin, check the "Nand erase all" in the checkbox and then click on "AP" buttion and select the "G7102DDUBNK1_G7102ODDBNK1_G7102DDUBNK1_HOME.tar" file.
5) Click the start button and wait for 5 mins till the OS is installed.
6) After installation, on your phone it might show 'memory damaged' and 'erase memory'. Don't worry, nothing is damaged or serious, just click to reset and everything will be fine.
7) Done!
I have provided the NK1 version link to you from my google drive account:
https://drive.google.com/folderview...03NF9WUzJLTHVSVnkzWWN5aFVQSzVOS28&usp=sharing
(Please hit thanks if I helped you)
Click to expand...
Click to collapse
I have same problem, please share the download link.

Categories

Resources