Related
Hi!
I do have problem to connect the device (o2 xda mini S) to WLAN. It recognizes the network, asks for the WPA-PSK key and then attempts to connect - but fails.
If I configure the device with a static IP this IP shows up during the
connection process after a while but the device isn't connected anyway.
If I use DHCP I get no IP ever.
I also tried a very simple 8 alphanum character key.
What may be wrong here?
I hope you get an answer soon, because I have the same problem. Enter the key, then no connect. I also tried it with security turned off on the router, no connect. This thing connected every time before 2.26 ROM update.
bump - having the same issue
bump
Hope there's a reply; having the same issue but I think it's router specific too. I am on Dlink DI-614+ and a friend of mine who has DI-524 (i think) has no problem connecting reconnecting.
if you figure out a way to get it to work, please PM me... I have not figured out this problem yet.
I might try to disable all of my router settings (WEP).. but that would only mess my already configured other devices up.
Stupid question, but is it a B/G router or is it configured to only do one of them ?
Well, I got it to work by disabling encryption and leaving the AP all open...
So, apparently the software has some WPA-PSK-related bugs
Same thing with 2.24a Mr.Clean. Open AP works fine, and any encryption messes the whole thing up. The connection is done, it even gets the IP - and continues to blink arrows and no data comes through.
Windows Mobile only knows TKIP but as I was using AES and wanted to continue using AES on the other machines I configured the router to provide "TKIP and AES". Well, this didn't work but TKIP only actually works now.
I've been having the same problems, could connect to unsecured networks, no problems. The thing would just refuse to connect to my home WLAN (Belkin 54G set to B/G), secured with WPA-PSK and TKIP data encryption. However, just updated the router's firmware from the Belkin website, and BINGO!!!! It found the router, I entered the key and immediately connected, fast too. Just try updating the firmware of your router!
I agree on the router upgrades. And some routers are just crap, sorry to say. I've had bad luck with Belkins and Netgears. Linksys and D-Link typically give me much less problems. You also need to make sure that you installed the registry settings to enable G networks on you device (of course)
I have a Sonicwall using WPA-PSK with no problems.
I personally like molski's tweaks to make the necessary registry settings on my device ... http://forum.xda-developers.com/viewtopic.php?t=58438
Hope I was of some help.
Hello to all
I have problems trying to connect through wifi on my new 8125.
After reading a lot of threads, i downloaded a program called hitchiker, who solves the wifi connection a lot easier and faster, but i keep getting the same error, the wifi connection appears, it connects but can not solve the ip address with the dhcp server and fails...
Can anyone told me if this is a hardware problem or a firmware issue?
my router is a netgear WG602 v2 with the last firmware available.
Thanks and happy new year to all!!
ddo you have mac filtering on? if so try turning it off
No, i used to have a wep security password, but i reset all settings on the router to factory, to try to connect.
i also have a laptop and a psp and both connect great!!
dont know what the problem is here, but its frustating...
I make it to work
first i did a hard reset, then i check on the log of the access point, and it was going through and forwarding the connection to the adsl router, but the problem apparently was on the dhcp server on the router.
i add a fixed ip, and now it works
still not working on dhcp but at least its working...
tanquef said:
I make it to work
first i did a hard reset, then i check on the log of the access point, and it was going through and forwarding the connection to the adsl router, but the problem apparently was on the dhcp server on the router.
i add a fixed ip, and now it works
still not working on dhcp but at least its working...
Click to expand...
Click to collapse
I'm having almost the same problem.
First I've tried to connect on my open lan in my house. I could connect, but couldn't get an IP automaticaly.
Today I went to the mall to try some open wifi lan. A friend of mine, with a Nokia n80 succsessfully connected with one of the hotspots. I've tried and couldn't get an IP. Suddenly, don't know why, I got connected, but couldn't surf at the web.
Then I realized that the fixed Ip that I've set before was still on. Changing it for dinamic didn't work.
So, I still can't get an IP.
Any Ideas?
I have a brand new wireless router; BELKIN N1 VISION.
I have set the security for this router as followed:
- Security Mode: WPA/WPA2-Personal(PSK)
- Authentication: WPA-PSK +WPA2-PSK
- Encryption Technique: TKIP + AES
Unfortunately my Qtek 9100 (with WM5) does find my wireless connection, but it refuses to make a connection after input of the WPA-code.
I'd try setting the security to either WPA-PSK or WEP. Some older laptops and wireless cards have issues with WPA2 and that could be causing it. Anyways, I'm probably wrong, thought I'd just throw it out there.
or also that you have a MAC (Media Access Control) Binding enabled on he router as a security measure.
I had the same problem yesterday, figured it out by adding my Wizard in the Access Control Enabled list.
Then there was the problem of not connecting automatically which I fixed by enabing IEEE.
Did anyone get this fixed ? - I have also bought a Belkin N1 - not MAC Enabled, no security enabled (WAP et al) - I live on a farm so that's not an issue !. My Nokia N95 *M works well with this over WiFi however my K-Jam finds the Router but cannot connect, comes back as unavailable all the time. HELP PLEASE !!!
hey guess what
my ignorant ass has.. the same problem!
my linksys router (WRT54G) has both b and g broadcasting (mixed)
i use static ip addresses and i'm not seemingly capable of assigning a static ip address on the G3.. before i attempted to assign the IP on the wiz, it would draw the connecting icon and eventually come back with "unable to obtain ip address"
so i knew that i needed to assign the ip.. so i gave it my best shot (i was able to do this on the laptop) and now it doesn't complain about not getting an ip address, it just never stops drawing the connecting icon, never connects, and i'm (obviously) unable to connect to the net via wifi.
any ideas or help or will this be a thread that just slowly rots without one of the xda-developer gods stepping in and solving problems for us brainless members?
hey man if it was a Ford i'd fix it for ya..
Hi, I have HTC Touch HD New. I have home wireless secured router DHCP with (WPA2 Mixed) with paraphrase While trying to connect I ran through wizard to connect to my wireless no luck. Then gave static IP , changed WPA2 to WPA/TKP, changed channel from 5 to 11 no response, stopped Firewall, anything what can be done with router did…..no connection. The HD sees the network, but refuse to connect. Although, I am able to connect to an unsecured networks. All other media that connected to my wireless network works fine. Also I have noticed that wile running wizard the: "Use IEE8021x network access control" is checked and gray so I am unable to uncheck it. Maybe here is the problem.. no clue. Appreciate any suggestion.
Hi,
I can confirm I have the same problem.
Not only with Touch HD but also with HTC Rapheal.
If I find a solution I will let you know.
I had this problem too. In the wizard you have to specify it as a 'worknetwork', not 'internet'. The 'internet' option is for public (secured) networks like on a café. Then again, maybe you did this already. I have a WEP encryption.
You might also want to check, if your HD connects at all by turning off encryption in your WLAN router.
If your HD connects fine, then check in Advanced Config under the "Network" section, if you have WPA authentication enabled. My ROM had this disabled. After I enabled this option and made a soft-reset, my HD could connect to my WPA2(AES) secured network.
If everything else fails, you might try this free supplicant: http://www.securew2.com/products/
Please, report back if and how you resolved the problem !
None of the sugestions here (post #3, #4 and #5) solved my problem.
It's still not possible to connect to a secured network.
Tried without MAC filtering and vissible network but no joy.
I use WPA-PSK with a network key.
Unsecured it connects fine.
spasovxda said:
If everything else fails, you might try this free supplicant: http://www.securew2.com/products/
Please, report back if and how you resolved the problem !
Click to expand...
Click to collapse
I had the same problem with my Linksys Wrt54g Router using WPA-PSK, no matter what I tried it just would not connect. Without encryption or WEP encryption it worked just fine. Did set Wifi to performance oriented on the HD since that seems to have helped others but still no success.....
Here's the rub: I had installed Schaps Advanced Config tool before and had enabled WPA authentication under network. In a last attempt I set WPA Auth. to disabled, did a soft reset.....activated Wifi, entered my (27 character) passphrase and...my HD connects to my router using WPA-PSK and MAC-filtering without a problem...so that might be worth checking as well...
i hav no problem conneting my blackstone to my linksys wrt610 router using wpa2-aes. maybe you hav ur mac adres filtering turned on
just my 2 cents
Ditto post #8..
I have just connected for the first time to my work network, WPA-PSK(AES) and it connected fine without any problems.
Switched on CM, waited for the phone to list the networks, selected the one I needed and then choose "work" for connection and entered our passphrase. Sync'd up without a hitch.
Just to put this out there - do not connect your phone to the pc when trying to go wifi. It is disabled when activsync is... active.
Hi,
Thanks for the help.
Yes MAC filter is enabled but I've added the adress of HD to the list so it should work.
Today I've changed the channel in my Zyxel router to channel 11 and ques what....
IT WORKS FINALLY !
Channel 11 I choose because that's what the Touch HD chooses in WLan settings.
Maybe this helps for other people as well.
Edit;
A small update to mention.
I have two devices here, Touch Pro and Touch HD.
They both connect fine now.
Also the Touch Pro seems to pick channel 11 as default channel !
I would love to see someone confirms this because it was a real bugger to me.
Edit 2;
With MAC filter enabled both devices won't connect.
Weird thing is, both devices have the same MAC adres !
playboy4u2nv said:
i hav no problem conneting my blackstone to my linksys wrt610 router using wpa2-aes. maybe you hav ur mac adres filtering turned on
just my 2 cents
Click to expand...
Click to collapse
Laurentius26 said:
...Weird thing is, both devices have the same MAC adres !
Click to expand...
Click to collapse
Are you sure you're seeing it correctly??? MAC addresses are unique, just as telephone numbers are unique to the phone system. Same concept. No two wifi devices are supposed to have the same mac address...
I was having the same issue: not being able to connect my HD to my wireless network. Very frustrating... Then I remembered I use a controlled Access List, on my wireless router, based on MAC addresses. Once I put my HD's MAC in the list, I was able to connect.
I made a mistake.
I connected both devices to the desktop with Active sync to find out MAC.
If I give the command 'IPCONFIG /ALL' both WM devices have the same physical adress,
but after I succesfull made a wifi connection (without MAC filter) with both devices,
I noticed that the MAC adresses are different on both devices in the router config window.
I've added both adresses to MAC filter and enable.
Now everything is up and running !
JesseW said:
Are you sure you're seeing it correctly??? MAC addresses are unique, just as telephone numbers are unique to the phone system. Same concept. No two wifi devices are supposed to have the same mac address...
I was having the same issue: not being able to connect my HD to my wireless network. Very frustrating... Then I remembered I use a controlled Access List, on my wireless router, based on MAC addresses. Once I put my HD's MAC in the list, I was able to connect.
Click to expand...
Click to collapse
Laurentius26 said:
Channel 11 I choose because that's what the Touch HD chooses in WLan settings.
Click to expand...
Click to collapse
Can this be changed on the Touch HD? I don't seem to be able to change it. And channel 11 is a bit oversubscribed where I am...
razorblader said:
I had the same problem with my Linksys Wrt54g Router using WPA-PSK, no matter what I tried it just would not connect. Without encryption or WEP encryption it worked just fine. Did set Wifi to performance oriented on the HD since that seems to have helped others but still no success.....
Here's the rub: I had installed Schaps Advanced Config tool before and had enabled WPA authentication under network. In a last attempt I set WPA Auth. to disabled, did a soft reset.....activated Wifi, entered my (27 character) passphrase and...my HD connects to my router using WPA-PSK and MAC-filtering without a problem...so that might be worth checking as well...
Click to expand...
Click to collapse
i had the same problem. my hd use to connect fine with my wireless ruter untill yesterday. everything i tryed failed until i red this solution. i've done what razorblader suggested and guess what. it works flawless.
thank you!
it seems that the problem occurs after instaling advanced config 3.3, wich i did yesterday. for some reason it seems it mess the wifi settings.
thanks again!
i still have another problem, wich i have it since i bought the hd
i connect my laptop to my wifi router and it works great. i connect my hd to my wifi router and it works (again) great
but if i connect my hd to my laptop via usb and activesync, my laptop lose wifi connection. i reconnect it, keeps connection for few seconds and it loose it again.
any advice?
thank you!
Confirmed...
Had the same problem, Advanced Config WPA disabled works like a charm, if you enable it it actually disables it...
I connect to a Linksys broadband router with Mac filtering and WEP with no problems. Too lazy to try WPA2 because I'll have to reconfigure 3 PC's and two wireless printers. If I do try WPA(2), I post here.
I have WPA2-PSK with mac filtering and ssid broadcasting disabled. And I never had any problems, my router is linksys wag200 if it matters. Maybe you just do something wrong?
Wi-Fi and Active Sync
noris08 said:
i still have another problem, wich i have it since i bought the hd
i connect my laptop to my wifi router and it works great. i connect my hd to my wifi router and it works (again) great
but if i connect my hd to my laptop via usb and activesync, my laptop lose wifi connection. i reconnect it, keeps connection for few seconds and it loose it again.
any advice?
thank you!
Click to expand...
Click to collapse
Note: This may be in a slightly different place in ActiveSync on XP.
I have Windows Mobile Device Center on Vista and I had the same trouble until I went to Mobile Device Settings > Connection Settings > check "Allow data connections on device when connected to PC"
(see attachment)
Just noticed you said laptop loses wi-fi.... I assumed HD loses wi-fi. My bad.
This may or may not help some of you, but I found out (the hard way) that the WLAN pre-shared key "passphrase" may only be 12 bytes long. Any more and it will not work.
-Valynor
I know Google has said they are looking into it. But this is ridiculous. The N1 can not handle WPA2 connections. Even though it saves the connection and password, it almost never reconnects automatically. From what I was reading on the Google help forum, it appears to have compatibility issues with many retail routers and they suggest upgrading the firmware on our routers. Throughout my day, I may connect to 3 different APs. One is a standard Linksys wrt54g with sveasoft, the others I connect to are Cisco APs.
None of them automatically reconnect. Most of the time on the Linksys, I have to delete the connection on the phone and re-add it.
I still like this phone but between the 3g and wifi issue, it is a pain to use.
I won't pretend to understand all that you just said, but I can tell you that my router is set up using WPA2-PSK. Not sure if it is the same as just WPA2 but my N1 reconnects to mine whenever I get in range. Then at the office it will connect to the WPA2-PSK set up in there, and one more regular open connection that is available at our pool. Pretty much every time I look at it, it is connected to one of those 3. Or else if I am OOR of any of those, I am on 3G.
My home router is a Belkin -N. Work routers are a Netgear -N and a D-Link -N.
I've got a Netgear WNR2000 on WPA2, and I can confirm I occasionally have this issue with the phone not connecting to the network automatically. It usually does if I go into settings and touch it to reconnect again.
There is an easy solution for any WIFI problems, use a Mac Filter!!
I have to go into Settings > Wireless & Networks > WiFi Settings before my Nexus One will reconnect to my home router, which is also using WPA2-PSK.
Hopefully it'll be sorted in a firmware update, it is annoying having to go through 3 screens to do something that my Nokia Symbian phones have been doing without issue for almost5 years...
I am having no problems auto connecting to my home WPA2 network, I am using AES encryption and running DD-WRT firmware if it helps.
philaldred said:
There is an easy solution for any WIFI problems, use a Mac Filter!!
Click to expand...
Click to collapse
Mac Filters are no replacement for WPA2 or encryption. Almost every device has the ability to spoof a mac address. Using a mac filter might help quickly eject roaming devices nearby, but it is NOT security.
Its like using a No Trespassing sign to replace locking your doors and windows.
i found that APNDriod may be a possible culprit....
Before I installed APNDriod , every times I go back home, my N1 will connect to my home WiFi almost immediately.
But after I install APNDriod, my N1 will not connect to my home WiFI.....I need to go into the Wireless setting screen, once i am on that screen WiFi it will connect.
But it is strange this I don't have this issue in my office, it just connect automatically before and after installing APNDriod.
Today I tried NOT to use APNDriod for a day and my N1 connect to my home WiFi without issue..... will do more experiment tmr.
Netgear WNR3500 w/ WPA2-PSK. Reconnects every time I am in range.
I find that my Linksys is the worst. The Cisco Aironet 1121 is better, but still has occasional connection issues. And I have not installed APNDroid.
On another note, when my phone switches from 3g to 2g and vice versa, it takes a long time for the data connection to resume
My network at home is setup with WPA2. I have no problems connecting to it... I click on the little wireless icon, and wait for it to say "wireless settings updated" and also wait for the wireless icon to show up near the time... then i will start browsing
I have a Dynalink RTA1025W
My wifi is working now. See h**p://forum.xda-developers.com/showpost.php?p=5773148&postcount=26
No problem reconnecting to my home network with WPA2 . Apple's Airport Extreme.
No problems here connecting to my Belkin N1 router. Connects the moment its in range.
Setup using WPA2-PSK
im having this exact same problem on my D-link Dir 615!
Pisses me off alot, i hope Google fix it!
I found that unless I was on channel 6 or 11 I had issues
AES-CCMP, TKIP or WPA Cisco521G will not connect
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
xoveruk said:
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
Click to expand...
Click to collapse
@xoveruk - Someone must be able to help sort out this issue !
xoveruk said:
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
Click to expand...
Click to collapse
My suggestion is - check what you're doing wrong before assuming the phone is at fault. And check that you're using PSK.
SEC AUTH ENCRYPTION
No security None Open - working
WEP WEP Open - no
WPA-PSK TKIP WPA-PSK - no
WPA2-PSK AES CCMP WPA-PSK - no
android 2.2 on N1, FRF91