i have had my xda2 for a couple of months now and i just picked it up and on the back to the right and slightly up of the camera lens there is now a hole where something was covering it before, i cnat rememebr what i never really noticed. inside i can see a gold thingy sticking up which looks like it might have thread on it. anyone know what im missing, how it oculd have gone missing and if it matters?
You just discovered the external antenna connector
If you dont use a carkit, it probably was covered with a small black rubber thingie. Apparantly you have lost the rubber thingie (or someone with a similar device borrowed it . . .).
Hi all, got a wizard 3 days ago and have been baffled with removing the back cover where to batery/sim goes. my htc Touch you simply slide the case downward, but this wiz i had to slip a knife down the slit on the side (marking the darn backing) and popping it off... this seems barbaric, already put 2 nicks on my plastics.... is there a simple way rather than almost breaking the darn clips with a knife each time? wat if i'm on the move, like now 'n no knife handy?
pls help, looked for tuts evrywhere... obviously missing something very simple here, right?
I use a case removal tool. Since it is plastic, it doesn't mark the case as easily.
Is this the battery cover that is removed by pushing the slider on the bottom to free the two clips, or the cover that sits atop the antenna?
Well my problem is that the plastic pin/hock that snaps the cover in place on the left side snaps loose when I push the above and lower horizontal edges of the cover....I have tried applying tape to the pin and snapin mechanism...no joy! Now I'm contemplating om sending the phone in for a new cover or new phone I really don't want to...my main concern is that I'll get a new phone with dead pixels and/or (heaven forbid!!) screen gap problem. So what would you guys do?
It should not be flimsy. It is a bit flexible thoough. You obviously have a faulty one.
If the actual phone is ok, I'd definitely hang onto it, there's enough hardware problems out there!
I'd contact HTC and ask them if they can send a replacement cover out to you first.
DIY fix on a phone this expensive? No thank you very much..
Hi there,
I broke my touch screen and tried to replace it by myself.
To make a long story short, I failed miserably (I broke the screen under).
However, I learned a few things I didn't met in the forum.
A- Disassembly of the case.
1- The Legend is glued. So, you have first to use hoven to melt the glue before being able to do anything useful.
15min/ 60 degree in the oven. Or use an hair dryer (I used the former).
2- Don't forget to remove ALL the screws (even the one behind the IMEI notice).
3- Don't try to open the camera lid before loosening the glue or you'll damage the aluminium body.
4- You have to unplug all the différent cables, so take notes to remember where all of them goes.
5- You must disassemble all the boards. There are 2 boards. One supporting the sim / SD connector, and one supporting the screen/touchscreen.
6- When disassembling the screen board, remove it by pulling the touchscreen at the bottom, and lift it up. don't pass a tool on the sides to remove it or worse, under the touchscreen, you'r tool will touch the screen under and break it (like I did). The screen is very, very fragile
Now, I'm stuck here because I can't remove the connector of the legent which is passed under the shield on the back of the screen.
I'm not able to remove the screen so I would like to know how to remove this shielding or get back the touchscreen connector to be able to replace it.
Once I figure out how to remove this shiled, I may be able to remove the screen too.
But now, I'm clueless (it was 2 in the morning when I gave up).
Maybe, some of you knew the trick to open this phone further.
I'd like to hear about it.
A little up to my post for the ones who did not read it till the end:
I can't remove the connector of the legend which is goind under the shield on the back of the screen.
I would like to know how to remove this shielding or get back the touchscreen connector to be able to replace it.
Once I figure out how to remove this shield, I may be able to remove the screen too.
But now, I'm clueless (it was 2 in the morning when I gave up).
mate it sounds like you have trashed your phone.they are built NOT to be taken apart.They require special tools and process to be repaired. The only thing i would suggest is contacting your insurance company and let them know that your phone was crushed under a car or something and then crush it under the car and you can get it replaced. If you dont have insurance, take some out and make a claim in say a month or two.
Its not an honest thing to do but your phone sounds busted and its the cheapest way of replacing that handset.
Post a pic of it if you can
Unfortunately, I have no rights to post a link or some put some pics.
Something about spam and profile that should be reviewed before being able show any pics.
This device is glued. No specialized tools are able to open it without removing it.
That would mean that the phone cannot be repaired, only replaced. My phone's motherboard was replaced, so at the service stations they should have special tools.
Fixed it!
Bottom right hand corner:
Bend the shielding back just enough to allow you to slip the connector in & then use a little glue to stick it back.
Maybe I was lucky, but my phones working as good as new again
I fixed my Legend
Guys, I know it's been a while since you talked but in case someone else is looking for this info, that's what happened to me:
I cracked the display of my legend and purchased a new one on eBay (roughly 40 pounds) - obviously delivered from Hong Kong but a genuine Samsung (in case you didn't know the Legen's screen as well as most of the AMOLED screens are Samsung's).
Then I used the above information plus some YouTube videos to give myself an idea as to what should I do. The result follows:
I used a hair dryer to heat up the back of the phone (camera and loudspeaker cover). Perhaps I should have been more patient as in the end I decided to use a knife with a very thin blade to lift it and I scratched the plastic and the aluminium body a bit. Anyways - the back clicks in but is glued in addition to that so you have to use both the heat and gently applied force.
Once you remove the back cover (which took me the longest out of everything) you should start removing screws. There's two behind the back cover and six behind the bottom cover (where the battery is). At this stage you don't have to remove all the screws - the bottom two, the one behind the IMEI and the one under the VOID sticker hold the main board but the two screws sitting deeper inside the phone's body hold the front buttons so you may leave them for now.
Now comes the trickiest part so read carefully: the main board is held inside the unibody by the screws (which we already removed), but is also glued right below the camera lens and along the sides. You should probably heat it up as much as you can and for a long time. I decided to do it the hard way. My dislplay was already cracked and it's the most delicate part of the phone so I said "whatever" and used the same knife as before - moved it alongside the screen (pushed it in gently from the front) until there was no resistance (the glue let go). Then I pushed and I heated the thing up and pushed and tried from every angle until finally the board slid out of the unibody. I hope you'll find it easier then I did as it seems that everyone describing it found it quite doable.
Now everything becomes easy-peasy. Remove the remaining screws to put the buttons aside (you'll have both the actul buttons and the tiny board with sensors - the latter sticks to the screen but once you remove the connectors, yu can take it off too). All the connectors are quite easy to remove if you hav a needle or something (just pull them out gently). I didn't worry about noting which is which as ther is practically no way you can mix them up - they're very different.
The rubbery plastic black surrounding of the board clicks in, so once you find the right spots you can lift them gently and take the thing off. You'll be left with the display covered by the shielding from the top and a thin metal board from the bottom. You have to remove two more screws to disconnect the main display plug.
And the final bit (that's where the thread's author had a problem I believe). My display was cracked but the shielding - fine. These two are glued together so I had to find some space for my finger nail and lift the shield. By slowly and gently pulling it apart I detached one from the other - and had to do the same thing with the metal board. Don't forget there's some extra stuff to remove from the back of the display - they're all glued but the glue will remain fresh enough for you to glue them again - this time to the new screen. The same applies to the front shield. I hope you won't let any dust sit on it in the meantime. You should have a screen protector on your new display if you bought it like I did. Remove it now and the display will be happy to stick to the old front shield just as if it was always there. The metal back will also fit in.
Now you can go through the above process backwards - just remember to connect all the connectors.
What I didn't do: I didn't use ANY glue putting the phone back together. As an effect the front shield is sticking out a bit (doesn't sit in the unibody tightly). It doesn't affect the phone itself but it gives you the funny feeling that something isn't 100% right. But I prefer that than screwing something up with a misuse of glue (glue can be disobedient).
The most important piece of information: the phone is working 100% correctly as if it was never disassembled by an amateur. Apart from two scatches on the back, the VOID sticker missing, the front sticking out slightly (less than a mm) and the missing battery slider (which I forgot to put back in and didn't bother to repeat the whole process for the sake of it) - there is nothing wrong with the phone. So if you ever crack you ever crack your Legend's screen - you can try fixing it yourself if you have the courage.
I would like to see some photos too But I'm never gonna take my phone apart - can't see the point
Foto's
Nice thread, i myself am wondering, if a better gsm antenna can be fixed inside the phone. and connect them to the 2 connections.
Do you have any pictures of the inside housing etc?
Hey all, havent been on here since I upgraded to a Dell product rather than my normal preference with HTCs but Im sure we have some knowledgeable people watching the Streak forum too. So heres the deal.. Dropped my streak while it was inside my Zagg case/cover from about 3 feet onto the floor. The screen no has a small crack and is barely sensing me touching it to unlock. First of all, I need to find a program to control the phone from my computer so I can save all my newer contacts to Google and whatnot, something like "My Mobiler," if anyone remembers that from Windows Mobile phones. Secondly, Im not to knowledgeable on how these screens work. I've never messed with a capacitive screen like this. Is there any way I can mess with the hardware to get it to function again? The crack in the glass is small, I wouldnt think the digitizer is messed up but like I said, I dont know. Can I tear it apart and maybe realign the digitizer or is it probably screwed? Thanks in advance.