Related
Hi!
I do have problem to connect the device (o2 xda mini S) to WLAN. It recognizes the network, asks for the WPA-PSK key and then attempts to connect - but fails.
If I configure the device with a static IP this IP shows up during the
connection process after a while but the device isn't connected anyway.
If I use DHCP I get no IP ever.
I also tried a very simple 8 alphanum character key.
What may be wrong here?
I hope you get an answer soon, because I have the same problem. Enter the key, then no connect. I also tried it with security turned off on the router, no connect. This thing connected every time before 2.26 ROM update.
bump - having the same issue
bump
Hope there's a reply; having the same issue but I think it's router specific too. I am on Dlink DI-614+ and a friend of mine who has DI-524 (i think) has no problem connecting reconnecting.
if you figure out a way to get it to work, please PM me... I have not figured out this problem yet.
I might try to disable all of my router settings (WEP).. but that would only mess my already configured other devices up.
Stupid question, but is it a B/G router or is it configured to only do one of them ?
Well, I got it to work by disabling encryption and leaving the AP all open...
So, apparently the software has some WPA-PSK-related bugs
Same thing with 2.24a Mr.Clean. Open AP works fine, and any encryption messes the whole thing up. The connection is done, it even gets the IP - and continues to blink arrows and no data comes through.
Windows Mobile only knows TKIP but as I was using AES and wanted to continue using AES on the other machines I configured the router to provide "TKIP and AES". Well, this didn't work but TKIP only actually works now.
I've been having the same problems, could connect to unsecured networks, no problems. The thing would just refuse to connect to my home WLAN (Belkin 54G set to B/G), secured with WPA-PSK and TKIP data encryption. However, just updated the router's firmware from the Belkin website, and BINGO!!!! It found the router, I entered the key and immediately connected, fast too. Just try updating the firmware of your router!
I agree on the router upgrades. And some routers are just crap, sorry to say. I've had bad luck with Belkins and Netgears. Linksys and D-Link typically give me much less problems. You also need to make sure that you installed the registry settings to enable G networks on you device (of course)
I have a Sonicwall using WPA-PSK with no problems.
I personally like molski's tweaks to make the necessary registry settings on my device ... http://forum.xda-developers.com/viewtopic.php?t=58438
Hope I was of some help.
Searched and searched, Has anyone had an issue with using the wlan SD8686 with WPA?
I can connect with no security and with WEP and I am able to browse the web.
I can still connect to the router using any of the WPA but can not get any pages to load in IE only works with wep or no security. 3 other laptops work fine.
Any idea? HTC Tech support no help.
Stealtheo said:
Searched and searched, Has anyone had an issue with using the wlan SD8686 with WPA?
I can connect with no security and with WEP and I am able to browse the web.
I can still connect to the router using any of the WPA but can not get any pages to load in IE only works with wep or no security. 3 other laptops work fine.
Any idea? HTC Tech support no help.
Click to expand...
Click to collapse
I can't answer.. but that reminds me the WPA issue that I have with the HTC Touch ..... my Touch is unable to use any WPA ... when connected the touch just freeze .. and I have to soft-reset and hope to the Wireless not connecting before being connected before disabling the Wireless.
it seems that WPA or the wireless chip is really bad ... but don't know which one !
Shift works fine with WPA I am currently using TKIP+AES
I have had nothing but issues with my Shift and Belking N Router using WEP...
Sometimes it would connect, the majority of the time the shift couldn't see the network and it did connect it would lose connection. I tried it with WEP and also with no security and also with MAC address authentication only. Every 50 times I tried to connect, it would connect maybe once.
So, decided to use my old standard 54g Belking router. Guess what, no issue so far with no security applied. Was planning to try it with WEP later....
faisal.husain said:
Shift works fine with WPA I am currently using TKIP+AES
Click to expand...
Click to collapse
I live in US and unit was from UK think this could be a problem with WPA?
I have no problem with NO security and NO problem with WEP only with any type of WPA. Also searching the net, seems like the wirerless chip in the SHIFT not a very good track record, lots of driver issues
faisal.husain said:
Shift works fine with WPA I am currently using TKIP+AES
Click to expand...
Click to collapse
Can you tell me what the Driver VER No is on your shift tfor the network card?
My unit has the Marvell SD-8686
Wifi
I had problems, sometimes the shift could not find my network, sometimes it woeked.
after setting my dlink dir655 router in b/g moder rather than b/g/draft n mode all has worked so far.
ok guys i use linksys running open source dd-wrt v23 sp2 firmware; works great; i must admit i have not used the shift on other wifi network routers....
No connection
Hi,
maybe someone can help. Since yesterday I belong tot he proud owners. But, but, I can’t get a connection to the internet over my WLAN router.
Router Netgear WPNT834. Whatever I did no luck: either I get the message: limited connectivity or only local Zugriff connection something like that.
No problem with XP notebooks, but with Shift and Vista.
Has anyone an idea what causes the problem? Is it the router?
Do you know any router you can recommend: strong signal and reliability?
Thanks
Settembrini
No issue with WPA here
Hi Settembrini,
So you got your Shift from Amazon.de at the same time as they delivered mine after all
Regarding the WiFi connection to the router, it seems to be some routers / chipsets.
I am also using WPA (with a Siemens SX550i router) and it worked without any problems. The Shift detected an encrypted network with hidden SSID and after I entered the SSID and the encryption password it connected immediately and with a stable connection.
WLAN access
Hi mw65719
yes, more or less same time.
So what is the conclusion? It is my Netgear router WPNT834, why I do not get a connection? Need for a new router it seems!
Thanks!
S.
Yes same here, I just bought the new Belkin N1 Vision router and all other equipment works but the Shift can't even see the the router. I just hooked a netgear router in series with the belkin and the Shift can now see the Netgear..... Was worried for a bit there.... Really annoyed about the shift not being able to see the belkin, the Belkin wasn't cheap.
Hi,
I was not able to establish a connection to my Netgear router WPNT834, then I tried the Speedport 700 V and it worked without any problems, no special settings in Vista neccessary.
I guess you have a different Netgear router than mine.
S.
I know Google has said they are looking into it. But this is ridiculous. The N1 can not handle WPA2 connections. Even though it saves the connection and password, it almost never reconnects automatically. From what I was reading on the Google help forum, it appears to have compatibility issues with many retail routers and they suggest upgrading the firmware on our routers. Throughout my day, I may connect to 3 different APs. One is a standard Linksys wrt54g with sveasoft, the others I connect to are Cisco APs.
None of them automatically reconnect. Most of the time on the Linksys, I have to delete the connection on the phone and re-add it.
I still like this phone but between the 3g and wifi issue, it is a pain to use.
I won't pretend to understand all that you just said, but I can tell you that my router is set up using WPA2-PSK. Not sure if it is the same as just WPA2 but my N1 reconnects to mine whenever I get in range. Then at the office it will connect to the WPA2-PSK set up in there, and one more regular open connection that is available at our pool. Pretty much every time I look at it, it is connected to one of those 3. Or else if I am OOR of any of those, I am on 3G.
My home router is a Belkin -N. Work routers are a Netgear -N and a D-Link -N.
I've got a Netgear WNR2000 on WPA2, and I can confirm I occasionally have this issue with the phone not connecting to the network automatically. It usually does if I go into settings and touch it to reconnect again.
There is an easy solution for any WIFI problems, use a Mac Filter!!
I have to go into Settings > Wireless & Networks > WiFi Settings before my Nexus One will reconnect to my home router, which is also using WPA2-PSK.
Hopefully it'll be sorted in a firmware update, it is annoying having to go through 3 screens to do something that my Nokia Symbian phones have been doing without issue for almost5 years...
I am having no problems auto connecting to my home WPA2 network, I am using AES encryption and running DD-WRT firmware if it helps.
philaldred said:
There is an easy solution for any WIFI problems, use a Mac Filter!!
Click to expand...
Click to collapse
Mac Filters are no replacement for WPA2 or encryption. Almost every device has the ability to spoof a mac address. Using a mac filter might help quickly eject roaming devices nearby, but it is NOT security.
Its like using a No Trespassing sign to replace locking your doors and windows.
i found that APNDriod may be a possible culprit....
Before I installed APNDriod , every times I go back home, my N1 will connect to my home WiFi almost immediately.
But after I install APNDriod, my N1 will not connect to my home WiFI.....I need to go into the Wireless setting screen, once i am on that screen WiFi it will connect.
But it is strange this I don't have this issue in my office, it just connect automatically before and after installing APNDriod.
Today I tried NOT to use APNDriod for a day and my N1 connect to my home WiFi without issue..... will do more experiment tmr.
Netgear WNR3500 w/ WPA2-PSK. Reconnects every time I am in range.
I find that my Linksys is the worst. The Cisco Aironet 1121 is better, but still has occasional connection issues. And I have not installed APNDroid.
On another note, when my phone switches from 3g to 2g and vice versa, it takes a long time for the data connection to resume
My network at home is setup with WPA2. I have no problems connecting to it... I click on the little wireless icon, and wait for it to say "wireless settings updated" and also wait for the wireless icon to show up near the time... then i will start browsing
I have a Dynalink RTA1025W
My wifi is working now. See h**p://forum.xda-developers.com/showpost.php?p=5773148&postcount=26
No problem reconnecting to my home network with WPA2 . Apple's Airport Extreme.
No problems here connecting to my Belkin N1 router. Connects the moment its in range.
Setup using WPA2-PSK
im having this exact same problem on my D-link Dir 615!
Pisses me off alot, i hope Google fix it!
I found that unless I was on channel 6 or 11 I had issues
AES-CCMP, TKIP or WPA Cisco521G will not connect
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
xoveruk said:
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
Click to expand...
Click to collapse
@xoveruk - Someone must be able to help sort out this issue !
xoveruk said:
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
Click to expand...
Click to collapse
My suggestion is - check what you're doing wrong before assuming the phone is at fault. And check that you're using PSK.
SEC AUTH ENCRYPTION
No security None Open - working
WEP WEP Open - no
WPA-PSK TKIP WPA-PSK - no
WPA2-PSK AES CCMP WPA-PSK - no
android 2.2 on N1, FRF91
I have my Tattoo rooted with 1.6 (can't recall the ROM name) with build number 1.67.405.6. Almost everything works fine except the connection with my home WiFi network. It's a PPPoE connection through ADSL modem. Next in line is the Netgear WG602 v3 WiFi router. At the beginning I couldn't connect at all so I changed the router's ROM to DD-WRT. Now I can connect with the router but no connection to the internet whatsoever. I can ping my router through my Tattoo, I can even open the 192.168.1.1 and mess around with its software but no connection to the internet. It is only limited to my Tattoo as I can connect through my laptop, through my other mobile (HTC S710) and also I can connect my Tattoo with any other WiFi (Secured or Open) with no problems at all.
I tried with no Security, with WEP, with WPA-PSK to no avail. Any other clues?
try running htc mail while you are using your wifi throuf your tattoo it worked for me
What is supposed to happen if I do that? I'm trying it as soon as I get home btw.
Nothing happened
Hi all...sorry for my interference but this problem is similar to mine.
I'm going mad from many weeks trying connect my Huawei Ideos (U8150) to my home wlan through a netgear VG602v3 AP. No way to do this.
Wifi works from my laptop and from my girlfriend's laptop, but from ideos it doesn't.
I turned off all wireless device in my house, I tried with/without WPA, I tried open network from channel #1 to channel #13, tried changing ssid and I also tried praying .
There is a weak wifi near here: it is on channel #1 and its power is between -89 and -82db. My wifi power (data from kismet) is between -50 and -18 db and is configured on channel #11.
In any cases, even if I put my Ideos near to AP antenna the story is ever the same:
- Ideos indentify the wifi network
- Ideos acquire the IP
- I open the browser or the android market and...
- Ideos lose connection...and so on.
I downloaded from work wifi (crypted with WPA) a wifi scanner from app store: it shows me the neighbour's weak wifi and my wifi network which appear and disappear recurrently.
Please, someone helps me (without suggest to buy another AP!!), any suggestions are welcome!!
Have you tried logging into the router and checking the privileges for devices. Some of them have a security element that restricts the use of the internet on newly connected devices until the setting is changed. I had a similar problem with a new laptop.
hope it helps.
I checked every setting to no avail. I still think somehow that my problem is with my router or adsl modem which doesn't connect automatically with PPPoE and Android doesn't have any command or software to initiate a PPPoE connection.
Other than that... Can't find any solution. Until then, I use connectify on my Win7 laptop. The thing is that I have to keep my laptop switched on as long as I'm in the house.
alpick36 said:
Have you tried logging into the router and checking the privileges for devices. Some of them have a security element that restricts the use of the internet on newly connected devices until the setting is changed. I had a similar problem with a new laptop.
hope it helps.
Click to expand...
Click to collapse
thank you for suggestion. I looked in depth but I did not found the option of which you were talking about. The unique solution still remains change the AP!!!
WiFi and Netgear Router
I think I finally found the answer. It appears Netgear routers support something called WiFi Multimedia. Its a QOS methodology. I disabled WiFi MM or WIMM as its sometimes called, as well as Internet QOS and all my problems connecting to web pages, the market, etc. through WiFi disappeared.
Strange that older versions of the ROM supported WIMM (or ignored it) and newer ones don't. But that solved the problem for me with no real degradation of performance on any of my other computers.
Good luck.
Sometimes my I9500 disconnect from my netgear router, saying that the password is wrong. I already tried different roms, official and non official. I also have updated my netgear router with the last firmware. Nothing actually solved the problem.
P. S. Seems if I put my 2.4ghz Wifi to work on 54mbps helps, but didn't solve the problem. And no, my notebook and tablet does not have the same problem, so it is not the router. A college of mine have the same issue with his galaxy S3 and his linksys router
Probably you should set your security to wpa2 and aes in your router.
But it is WPA2...