Database Users

Problem connecting to O2 after unlocking XDA

Hello all
My colleague posted this message a couple of weeks ago, but didn't provide full info and as such the replies did not work. :roll:
So here it is. I would be grateful for any advice.
I unlocked my xda I, using a software I downloded from here, which was previously working on O2 UK. After that, it doesn't work with any O2 Sim. It works with all other UK sims (Vodafone, T-Mobile, Orange). But not O2. The O2 sims are ok as they work on other handsets and specifically my unlocked XDA II and other handsets ( I have tried 2 different O2 sims).
But no joy. I even tried to change the GSM frequency on the XDA through boot loader (even though I didn't have to), but no joy. I have gone through the auto config several times. but no joy. I even re-installed the latest O2 firmware and radio update (from the O2 web site), but still no joy.
I am running out of ideas. Does anyone have any idea? Should I try and downgrade the firmware and radio stack and try again? Can I do it from the original CD?
I would be grateful for any ideas.
Cheers
Nima

Can you tell us the nature of the error with an O2 sim, what is shown at the signal level meter, what happens when you attempt a call etc. Please leave the radio stack alone, your phone is working on 900 and 1800 bands so that is not the problem. Was the sim that you have at the moment working on this phone on O2 before the upgrade.?

Hello Thank you for your reply.
When you turn the phone on, it asks you for the SIM pin and the device works fine in every other way. But you get no signal. If you try to make a phone call, you get the phone dialer screen and you can dial the number but, obviously, it disconnects more or less immediately. If (from the phone dialer screen) you try and go to options it freezes and doesn't show you the options screen and then you can only exit the phone dialer. Also, I put the GSM frequenct back to what it was. I haven't changed anything in the bootloader mode anyway. I had problems with the original O2 sim after the upgrade (funny enough, it worked for a day or two), but now i don't have that sim as the contract finished. By the way, both of the O2 sims I am trying now are contracts and NOT pre-paid.
Well here it is. I hope this helps to let you figure something out. I would be grateful for any ideas. What about formware downgrade? what do you think? could it help ? is it even possible?
Thanks a lot.
Nima

It presents as a blocked phone, if you look closely at the signal meter after a soft reset you may see the signal come up but then drop back to nothing. It may be coincidence that it stopped working with O2 2 days after the upgrade. I have seen this happen with phones that either have been subject to insurance claim or where a contract was not fully paid up for the 12 months, however it usually means it will be blocked on all networks. It does not look like a rom downgrade will work, also as said before, if it works on Vodafone it should logically work with all other 900 mhz bands.

"Phone Not Ready...." Can anyone help?

I have an O2 XDA mini s as its so called, and an Orange Sim (both UK)
Now I can make/receive calls fine, but when I try to send a message, or goto the "phone" option, I get the message below. Nor do any contacts from my sim show up.
"The phone is not ready. Wait 15 seconds and try again"
Does anyone have some advice to resolve this as its pretty annoying!
I did try a search and got no results, so please forgive me if this is a topic that has been given the run around before.
Regards
Sam

Sounds like the simcard is dirty try taking it out and inserting again happens on probs every1 phone sometime.

Another option would be to go back to your cell provider and request they give you another SIM card

sounds like you might not be getting a strong enough signal to use the phone...or send out messages...consider flashing your radio rom to something higher (do a search for radio rom). radio rom flashing usually won't effect the os or ipl/spl...so you can keep all your existing settings. newer radios have more information on towers...so it has a chance to get a better signal...or at least that's what i've been told...
2.19.11 is common for cingular...but there's a post somewhere on changing something that will let you use higher radios with cingular without too many problems...personally, i'm messing around with 2.69.11 (t-mobile) and i haven't had any problems...

Tried cleaning the sim card to no avail.
As with regards to the radio rom, im sure thats the issue as i can make phone calls fine, so im getting a signal. It just seems accessing the sim card and texting is the issue
Its bugging me because its an awesome phone. Im wondering if its due to it being a different network branded phone to the sim card im using...
Sam

Ozington said:
Im wondering if its due to it being a different network branded phone to the sim card im using...
Click to expand...
Click to collapse
if that's the case, you may need to sim unlock your phone? but if you're making and receiving calls, you should be fine...
if the sim card is old, or the service provider was taken over...or something of that sort, maybe your sim card has a problem...something like this was a problem back in the US when cingular bought out at&t...the problem was resolved by consumers going to cingular to get a 64kb sim card rather than a traditional 32kb...perhaps something of that sort is happening there?

I suppose that is a possibility,
I will try using the unlocking tool, but im not sure it would be the sim as it is only 2 months old. I just didnt like the phone i got with the contract so bought this.
I will certainly try. I kinda wish i'd just bought the Orange version of the phone
Oz

@Ozington. If you can make calls, chances are your phone is already unlocked. Did you bought this phone 2nd-hand? The previous users may have done something to it. Soft reset your system and tell us all your stuff (especially the Radio/GSM displayed) displayed on the first boot screen.
Alternatively, if you want to avoid all O2 crap, hardreset your phone and during init setup, soft reset it (poke it) just after you have done your security settings. If it is not using official ROM (e.g. no O2 stuff around to be seen), make a guess on the ROM used, and you can also try upgrading an official ROM (safe to do so).

Hanmin,
The phone was bought from ebay, but was brand new sealed, all in o2 packaging, the seller stated it was unlocked. It was all factory packed and the seal wasnt broken..
The Device info is as follows:
Rom Version 2.21.4.1 WWE
Radio 02.07.10
Protocol 413.1.03
ExtROM 2.21.4.101
Does this mean anything?
Regards
Sam

I'm doubtful that it is factory sealed and unlocked. From the information you gave (although not those I've asked for), seems that your phone ROM is a bit, old. Go to O2 webpage and download an update for the ROM (I'm not sure, but I think they have an updated ROM).
To check your ROM version, tell me the battery icon on Today screen, is it on the top left or bottom left. Top left battery icon means it is AKU2, the updated version.

To throw a spanner in the works the battery icon is in the top right?
Thanks for your help. What info did i miss out? (Please bear in mind i have no idea what im doing with the more technical side of the phone!)
Regards
Sam

I briefly had this problem as well. In my case, I could also receive text messages, but still could not send. I changed OS's and it was fixed. The problem only seemed to happen with one of the new OS6 roms. It was intermittent, and even resetting the phone seemed to solve the problem occasionally and briefly. I have flashed my device too many times, but think it was the most recent Touchflo version that had the problem for me. I was using radio 2.69 Ipl/Spl 3.08. I hope this might help. Good luck.

Orange SIM & Unlocked T-Mobile MDA Vario
Hi Guys,
Just a quick note to say that I have a similar problem with my new Orange SIM.
All the GPRS works fine, calls send & receive OK, POP3 email works a treat but no text messaging and when I try Start > Settings > Personal > Phone .. I get "The phone is not ready. Wait 15 Seconds and try again"
I have no answers to this but from all the searching I have done over the past few days to try and find a cure this problem seems to be common to Orange SIM cards. All I can think of is that the Call Centre Message Number needs changing to get the txt messaging to work.
The phone has worked fine on other networks - no GPRS but text messaging & phone calls
Any advice gratefully received !!

Hi guys first poster so be nice
I've got the same problem but came from T-Mobile to Orange.
My IPL / SPL is 1.03 so I'm going to upload the newer versions on the fourm to my phone and see what happens tommrow. Havn't got the time at the moment but I'll post up how I get on.
Do you guys think this is a good approch to the problem I've got?

Hi Sasyboy
You posted just after me. I got my phone working great on Orange now. It has taken me 3 days !!
You'll have to be careful on how you do it. I just jumped in and it caused me a lot of work and time. and a long period where I thought it was bricked 'cos the bootloader screen stayed on and I lost all comms with the MDA
First make sure the CID is unlocked, you must read this:-
http://forum.xda-developers.com/showthread.php?t=285435
I wish I had. This may seem a long way of doing it, but you don't want an expensive paperweight do you ??
After you have unlocked the CID and updated everything as per the Dr P stickie (link above) and it is working, you then need to get the Wizard_Love ROM upgrade. I tried after doing all the Mr P instructions in the stickie but still kept getting the "Phone is not ready...." so I decided I then needed the Wizard_Love ROM upgrade. This took me ages to find, I tried to d/load it via uTorrent but only got 25% and then found it on a Russian website - anyway I have it now, and as I said you'll need it, PM me and I'll get it to you.
You will have to download several files and set half a day aside. If you are struggling PM me and I'll get the files to you as I have them now.
I just need to get the Ornge MMS settings right and then all is fine. GPRS, POP3 email, Internet, Txt messaging OK now, SIM manager works fine (didn't even have it before!) and can access all phone settings for call divert etc
Good luck. Any queries I may be able to help, but I'm no expert. I have spent hours looking at this forum and all the answers are there it is just getting them in the right order.

How do all,
Really happy I updated everything and now it all works fine. Thanks to the community. I love this phone and now with updates it's even cooler.

WM6 upgrade - then no network

I upgraded to WM6 artemis touchflo ROM. Worked fine initially then I lost the network. Is constantly searching.
Try Find Network and just searching
Try change Network selection to manual and get following message:
Network error
Cannot read settings from the network, Try viewing settings later or disconnect data connection and try again.
Retry Cancel
Get the same error if I try Set Networks.
Can anybody help please ?
Saw this on the HTC website today ''The TyTN becomes the first HTC device to get the upgrade, with the HTC P3300, S620 and Advantage also scheduled to receive the upgrade from August''

Have you tried doing a soft reset? (stylus in the hole)

I've tried soft reset, hard reset the lot. Still no joy

Can't think of any other good ideas off hand. Maybe try a reflash?

Why not try just re-flashing the radio first.
Found here

Gajet said:
Why not try just re-flashing the radio first.
Found here
Click to expand...
Click to collapse
Thanx - re-flashed the radio but still the same problem. Is there anything else I can try please ?

I never thought I'd say this piece of CS crap, but have you checked the contact of the SIM card, try cleaning the SIM with a dry cloth.
Otherwise a re-flash of the ROM is probably the next best step.
Can you check the SIM works OK in a different phone?

Thanx - SIM works fine in another handset and have flashed back original T-Mobile ROM. Could it be anything to do with the WM6 ROM I used ?

shaggy1965 said:
Thanx - SIM works fine in another handset and have flashed back original T-Mobile ROM. Could it be anything to do with the WM6 ROM I used ?
Click to expand...
Click to collapse
Yes, If you desperately want Touchflo, then Tom's B&B 4 is imminent, his track record at ROM releases can't be faulted.

Sorry don't think my last post was very clear. Have flashed back to the original T-Mobile ROM and still same problem no networK

Oh! That's not good.
Sounds suspiciously like a hardware failure then.
Still under warranty?

Got it fixed under warranty by local T-Mobile store Thanx for your help and advice

what was the issue then, i am having the same issue with my orbit, and can not seem to find the problem? i reflashed all versions of the radios, and changed to all kinds of sims availabe on Rogers network in Canada, and the phone works fine from all features, except it does not conenct to the network??? when i do search the network, it reads all the towers available, but does not register on any network !!!
the first time i changed the sim worked like a charm for 30 min, and then the phone de-registrerd itself from the network, and i could not connect again. i could always get it to work for maybe an hour at the most everytime i change to a new sim card, but this is not a solution and a costy one

v1605 Video Phone Not There

Hi guys
I've just received my third v1605 from Vodafone (1st backlight broke on screen replaced under warranty, 2nd got run over by a car ) in three months. The latest one came with a new sim as my old one was destroyed in the accident. I've had the SIM activated and all my old settings reinstated from what I can tell.
I've got access to 3g so can access my ISP email and the web. I can make voice calls and send/receive SMS. One thing that is different to the previous two phones of this model I've had is the video calling function. The button is on the faceplate as before but when pressed it only opens a voice softphone screen. The software phone has no option at all for video calling. It looks like a completely different phone app to previously, certainly not the one shown in the manual. I've spoken to VF customer services who haven't a clue to be honest, although they do say there are 3g problems in the London area which may be the problem. (I can use 3g data services no problem and connect with HSDPA from what I can see (H Icon))
Any thoughts on how I can reinstate the correct software phone?
ROM version 2.07.161.1
ROM Date 02.06.07
Radio Version 1.32.00.00
Protocol Version 32.65.7020.09H
Model No HERM200
Cheers for any help you can offer.
Charles

Welcome to the forum.
I don't use the video function, but do have the same phone version (with vodafone) as you. One thing I do remember when playing with the phone when new is that if you hard reset, then soft reset to disable the vodafone customisations then you do lose the video functionality.
So, if yours is the stock vodafone rom you may need to hard reset to get back the video call function.
If it is stock rom but without the vodafone customisations you won't get video call function.
If it's the stock rom maybe you should try a hard reset - it might bring back the function - BUT make sure you back up all your data first because it'll be erased with the reset.
Also, if you are still using the stock vodafone rom, why not try one of the wm6 roms from this forum (I think Schaps 3.54 is one of the best). But before you do, please read lots (the stickies on these forums) especially about CID/SIM unlocking and olipro-2.10 before you start. A good place to start is mrvanx's guide.
Hope this helps a bit.

Cheers ach2. I'll investigate as you suggest.

Please help!! SX66 radio

I've loved my Blue Angel for 2 1/2 years thanks to xda-developers, but right now I just wanna throw it away!
I have a Cingular SX66 (PH20B1) running WM6 from Xplode (6.00.00.WWE) and the radio 1.15. After I upgraded to WM6 everything was kind of OK I thought, until I realized that sometimes calls weren't getting through to me and I was getting 'No service' too often. That's when I upgraded the radio to 1.15. I was getting the no radio error, but I found through searching that if I soft reset and keep the phone charged the radio comes back.
Here's my problem.. even when the phone gets out of 'No service' and finds the network (even showing me full signal strength) I can't make calls! Calls won't come through to me! It's pretty useless as a phone, but it seems to be usually able to send text messages if I have the network. It takes endless soft resets and long waiting just to get it to see the network, and then the phone still doesn't work.
The sim card is fine, and it seems the problem is the same if I downgrade to 2003SE (by the way, I only seem to find T-mobile ROMs that work.. don't know where the WM2003SE ROM is I originally had on here).
The phone only seems to work sometimes if I after I soft-reset, I make the call while the BA is still on the cradle.
If anyone knows of a solution I'd really appreciate it.. on WM2003 my SX66 would only act funny if the charge fell to 60%. Now it's wacky with all the up/downgrading/charging/soft-resetting I've tried.
Thanks!

Additional info
I don't know if this is related, but I have the storage almost full of installed programs and the device is much slower now. Also, the Data Connection buttion is grayed out in HTC Comm Manager.
The phone seems to be working right now. Give it an hour and it'll probably be wacked again

Final solution for 'No service'
Hi burnblue...
Try this thread: http://forum.xda-developers.com/showthread.php?t=340557
This resolved my problem...
1) In WM2003 and install bandsel .CAB
2) Choose a band of your operator gsm/country (in Brazil, for my operator is 900/1800Mhz (Operator "Claro" and "TIM")... here in Brazil we have another operator what works in 850mHz (Operator "Vivo").
3) If you want, upgrade your rom for WM6 (much better)... your band selection will be fixed (came to wm2003). I don´t undertand about fixing a band remain after rom version upgrade... No explain about this.
No more issue about radio gsm signal, be happy....
Works perfect to me, I´m 100% certain about this procedure.
Rodrigo Pelosini
burnblue said:
I've loved my Blue Angel for 2 1/2 years thanks to xda-developers, but right now I just wanna throw it away!
I have a Cingular SX66 (PH20B1) running WM6 from Xplode (6.00.00.WWE) and the radio 1.15. After I upgraded to WM6 everything was kind of OK I thought, until I realized that sometimes calls weren't getting through to me and I was getting 'No service' too often. That's when I upgraded the radio to 1.15. I was getting the no radio error, but I found through searching that if I soft reset and keep the phone charged the radio comes back.
Here's my problem.. even when the phone gets out of 'No service' and finds the network (even showing me full signal strength) I can't make calls! Calls won't come through to me! It's pretty useless as a phone, but it seems to be usually able to send text messages if I have the network. It takes endless soft resets and long waiting just to get it to see the network, and then the phone still doesn't work.
The sim card is fine, and it seems the problem is the same if I downgrade to 2003SE (by the way, I only seem to find T-mobile ROMs that work.. don't know where the WM2003SE ROM is I originally had on here).
The phone only seems to work sometimes if I after I soft-reset, I make the call while the BA is still on the cradle.
If anyone knows of a solution I'd really appreciate it.. on WM2003 my SX66 would only act funny if the charge fell to 60%. Now it's wacky with all the up/downgrading/charging/soft-resetting I've tried.
Thanks!
Click to expand...
Click to collapse

"no service" is a issue...
Your problem about slower is another problem...
Storage full ~ slower... I had problem´s about these in anothers pda´s.
Take easy to storage your files, much components in today screen, etc...
Use sd card, this help.
Upgrade for Wm6 (xplode rom) and be happy...
WM6 by xplode is faster.
What´s your radio rom version? 1.15 ?
If < 1.15, then upgrade....
Rodrigo Pelosini
burnblue said:
I don't know if this is related, but I have the storage almost full of installed programs and the device is much slower now. Also, the Data Connection buttion is grayed out in HTC Comm Manager.
Click to expand...
Click to collapse

not yet
Thanks for the advice rod, but I still have problems.
1. I saw that thread too, and it's not that I have totally 'No service' -- I have signal but calls just won't connect. It might work one minute, but 90% of the time it just doesn't.
2. I can't find a working ROM for my SX66 to downgrade to 2003. I remember weeks ago when I was trying to fix this I think I found a T-mobile ROM, but nothing is working for my downgrade now.
Why is my phone radio so unreliable?

Strange problem...
I have some tests for you...
1) Do you enable PIN ? If yes, then disable.
2) Do you upgrade your radio rom to 1.15? No? Then apply.
3) Do you have problems with anothers gsm chip ? Your SX66 is gsm or cdma ? Possible issue in your gsm chip, maybe... Try another gsm, another operator...
4) What´s the message errors or problems with upgrade or downgrade rom ?
If your sx66 is a cdma phone, sorry, I don´t have any idea how to help you.
In this case, ignore all my questions. My experience in Blue Angel is about gsm...
Take care...
(Send a message if you resolve or not this case...)
Rodrigo
burnblue said:
Thanks for the advice rod, but I still have problems.
1. I saw that thread too, and it's not that I have totally 'No service' -- I have signal but calls just won't connect. It might work one minute, but 90% of the time it just doesn't.
2. I can't find a working ROM for my SX66 to downgrade to 2003. I remember weeks ago when I was trying to fix this I think I found a T-mobile ROM, but nothing is working for my downgrade now.
Why is my phone radio so unreliable?
Click to expand...
Click to collapse