Related
Hi, got some problems with one of my employes Herald (not simlocked or anything).
It ended up on my desk after complaints about it rebooting by itself every minute or so. I figured I could sort it out by upgrading to wm6. Wen to HTCs website and downloaded the official RUU (HTC_P4350_SVE_4.17.413.2_4.1.13.44_02.94.90_Ship.exe). Everything went along fine and I left it upgrading on my desk and went for lunch.
When I got back it said that the update had failed and I followed the recover function but without success.
Now Im stuck in bootloader mode, and when I try to update it again the current image version is listed as blank and I get to about 1-2 percent before it shuts down and gives "ERROR [244]: INVALID MODEL ID".
Any suggestions on what to do?
Further information...
IPL 4.17.0001
SPL 4.17.0000
When i do a hard reset, after it says format complete it boots up and freezes with a green gradient across the screen.
You can try using USPL or HARDSPL to flash.
The USPL will get around CID locks
This is from ivan's A Herald's Guide to Flashing Aserg, USPL and HARD-SPL - xda-developers
II. How do I flash an NBH file?
Warning: To use the NBH ways, you MUST have a SPL of 4.0 or higher. If you have a lower SPL, you WILL brick your phone.
a. USPL
Step 1. Download Herald-USPL-Beta3.
Step 2. UnZIP the file into a folder on your Desktop. Let's call it "MyFirstROM" for simplicity's sake. Notice that there is a folder called RUU within this folder now. Keep that in mind.
Step 3. Download your NBH file and unZIP or unRAR it into that RUU folder. Make sure that that NBH file ends up in the RUU folder, not within a folder inside the RUU folder.
Step 4. Place your phone into flightmode.
Step 5. Go back to the MyFirstROM folder and then run USPL.exe
Step 6. Follow the directions on the screen. EXACTLY.
Your screen on your cell phone will go white around the 75% part of the "second step" now.
ActiveSync will LOOSE its connection.
Step 7. One step 3 on that black window, the RUU flasher will pop up. Just follow the steps.
That's it. Welcome to the flasher's world.
Thanks for the reply,
First, I cant get activesync to find the phone, only evidence of contact in between the phone and PC is that its listed as [Windows CE USB Devices+PocketPC USB Sync] in device manager. I tried to uspl flash with ASERG.8, and it stops at "STEP 1/3...."
I downloaded mtty to see if it could connect, and it did.
Any further suggestions on what might work!
uninstall..reset.. clean install would probably get activesync to work w the phone..
Reinstalled activesync without any change. And soft/hard reseted everything…
Tried to flash via sd as per instructions in another thread, got to "checking SD contents" and then straight to triple-color bootloader.
Help me please! ;D
Cant help getting the feeling that Im completely screwed...
Cant get activesync to recognize it, only way to get it to light up is via bootloader (camera + reset button), everything ive tried to flash it with hangs almost instantly.
As a complete novice my guess is that the current rom is corrupted and I badly need advice on how to go on. The sd-flash seems quite logical but I cant get it to work. Ive tried to overwrite my sd with 00-values in winhex and then placing the original ruu [HERAIMG.nbh] (through windows, is there a way to write data with winhex?) on the card without any success.
Any suggestions on what to try is much appreciated.
Sounds like the SPL got corrupted or partially written only... sorry. Repair center time. You can also placing your Stock RUU's nbh file into your SD card and renaming it to... umm.. I forget... and then flashing FROM the phone.
facdemol said:
You can't simply place the rom file to the card and hope the device will read it in this way. In my time working for pda service, we used WINHex to format the card (to RAW-unformatted) and then we wrote the rom file in RAW format to the card. Your card looks like an endless stream of hexazecimal values. Only winhex recognises this format, if you insert the card to the computer, it will simply ask you to format it. After inserting this card into the pda, it will start the upgrade . The order of this operation was, as I remember, to fill the card with 0000 values (there is an option in WINHex, a kind of format) then write the rom file to the card in RAW mode. Then insert the card to the device.
Click to expand...
Click to collapse
Thanks for the reply, before giving up and sending it in for repair I would like to give the sd-flash a proper try... So far Ive managed to format the card with winhex but I cant really figure out how to write to the card in raw format. Could anyone point me in the right direction?
i managed to do the steps said above ... formated the card in RAW format etc but still the phone won't turn on ... it will only stay in bootloader ...
diabolic53 said:
i managed to do the steps said above ... formated the card in RAW format etc but still the phone won't turn on ... it will only stay in bootloader ...
Click to expand...
Click to collapse
Care to enlighten me on how you did that?
I've been reading a lot lately.. I wonder if the phones are savageble... something about flashing but bypassing the radio check... Also, the universal has an RUU that bypasses any checks before it flashes... this would be great for us to have... I'm asking around...
g4rwin said:
Care to enlighten me on how you did that?
Click to expand...
Click to collapse
whell i opened the mem card with winhex filled all the blocks with 00 and then i opened the nbf file also with winhex and copied the content in hex format on to the card ....but still no success ..
ivanmmj said:
I've been reading a lot lately.. I wonder if the phones are savageble... something about flashing but bypassing the radio check... Also, the universal has an RUU that bypasses any checks before it flashes... this would be great for us to have... I'm asking around...
Click to expand...
Click to collapse
if you find it please tell us about it cos a lot of phones are getting bricked ...
If I'm correct, you told us a few post above thisone you placed your SD card with the imghera.nbh and got "checking sd conents" and then it went to bootloader.
As far as i can recall you need to get your Herald into bootloader first and then place your SD card with the IMGHERA.nbh file on it. Then it should start reading the image from, your SD card.
Judging from your first post you haven't been using the asigned RUU from the HTC website if this was your first rom flash to WM6 and you got a vendor error. Try to convert and use that one when you flash from sd card.
jappo01 said:
If I'm correct, you told us a few post above thisone you placed your SD card with the imghera.nbh and got "checking sd conents" and then it went to bootloader.
As far as i can recall you need to get your Herald into bootloader first and then place your SD card with the IMGHERA.nbh file on it. Then it should start reading the image from, your SD card.
Click to expand...
Click to collapse
Ive tried all possible ways, if I pop the sd card in while already in bootloader, nothing happens at all.
jappo01 said:
Judging from your first post you haven't been using the asigned RUU from the HTC website if this was your first rom flash to WM6 and you got a vendor error. Try to convert and use that one when you flash from sd card.
Click to expand...
Click to collapse
Ive been trying to flash with the WM6 RUU I downloaded from HTC's site (the one that bricked it) since that is the only local (swedish) and official one I could find. Have I misinterpreted it all and the only thing that could do the trick for me is WM5.1?
Ive also been trying to contact the HTC service dept for over a weeks time ending up in a deadend overfilled voicemailbox - meanwhile my warrantyperiod ran out... Any suggestion on what to do?
duprade said:
You can try using USPL or HARDSPL to flash.
The USPL will get around CID locks
This is from ivan's A Herald's Guide to Flashing Aserg, USPL and HARD-SPL - xda-developers
II. How do I flash an NBH file?
Warning: To use the NBH ways, you MUST have a SPL of 4.0 or higher. If you have a lower SPL, you WILL brick your phone.
a. USPL
Step 1. Download Herald-USPL-Beta3.
Step 2. UnZIP the file into a folder on your Desktop. Let's call it "MyFirstROM" for simplicity's sake. Notice that there is a folder called RUU within this folder now. Keep that in mind.
Step 3. Download your NBH file and unZIP or unRAR it into that RUU folder. Make sure that that NBH file ends up in the RUU folder, not within a folder inside the RUU folder.
Step 4. Place your phone into flightmode.
Step 5. Go back to the MyFirstROM folder and then run USPL.exe
Step 6. Follow the directions on the screen. EXACTLY.
Your screen on your cell phone will go white around the 75% part of the "second step" now.
ActiveSync will LOOSE its connection.
Step 7. One step 3 on that black window, the RUU flasher will pop up. Just follow the steps.
That's it. Welcome to the flasher's world.
Click to expand...
Click to collapse
Hi I try tu patch IPL/SPL with hard spl but with error, now my herald stuck in boot mode. IPL/SPL 1.09.0001. He probbably is from some russia operator (rusian diacritics on keyboard).
How can I try to make him alive?
guyz,
plz help me out...
someone please provide me tutorial for applying roms to my pharos,
i m from india can i apply any rom?
i read in this forum
Quote:
My HTC Pharos 3470 is HardSPL now ... w000t !!! %)
Did it from the first time ... thanks to Suracha and the reading of this whole thread ... (my spl was SPL 1.11.0001)
Here are some basic notes for those who are still stuck
1. Set Button 3 (Camera) to <None>.
2. Transfer the extracted files (JumpSPL.exe & Pharos_JumpSPL.nb) to your device and execute.
3. Change 0x00000000 to 0x10000000 as Jump Address.
4. After geting the file list, press Camera first; then press Power. This is little difficult, if you pressed Power too long; you device may be turn off.
5. Tap the Pharos_JumpSPL.nb file, it must be tabbed while Camera & Power button are pressed.
6. After above, you should get grey background screen.
7. On ur pc quickly ( means make usb connection ) double click the ROMUpdateUtility.exe from the HardSPL dirrectory, and follow through the flashing process (what steps in flashing process?)
several question from me.
1) are this steps right?
2) what to do when get Grey background?
3) should i have to remove memory card and sim card?
4) did i have to backup my og rom? but how?
plz correct me >>>
I m also searching for the working tutorial to flash a rom in a safe way and avoid any damage to the phone!So can anybody help me???
Both of you are on the right path. The steps listed are definitely correct. Flash HardSPL files once using the below method first if you are not concerned over the warranty. Then you can flash any ROM you like from the Forum as many times you require. Incidentally the HardSPL for it doesnt seem to be permanent in my Pharos. I was experimenting with some ROM's and then flashed back to Original 6.1 ROM from HTC and voila it was back to original HTC SPL. Now I have to use Suracha's method or HardSPL again to replace the ROM as its back to the restricted SPL.
hey i recently got a htc pharos i wanna put android on this or the manila rom can someone email me links mactvsinist
[email protected]
Original 6.1 ROM from HTC for P 3470
Where can I find the Original 6.1 ROM from HTC for P 3470 and can the radio, ROM & SPL of my WM6 phone be upgraded without Jump/Hard SPL, if I update with this original ROM.The Current specs are:
ROM - 1.11.707.1 (Dt. 29/01/2008)
Radio- 03.15.90
Protocol Version - 4.1.13.59
wayne_rooney said:
i read in this forum
Quote:
My HTC Pharos 3470 is HardSPL now ... w000t !!! %)
Did it from the first time ... thanks to Suracha and the reading of this whole thread ... (my spl was SPL 1.11.0001)
Here are some basic notes for those who are still stuck
1. Set Button 3 (Camera) to <None>.
2. Transfer the extracted files (JumpSPL.exe & Pharos_JumpSPL.nb) to your device and execute.
3. Change 0x00000000 to 0x10000000 as Jump Address.
4. After geting the file list, press Camera first; then press Power. This is little difficult, if you pressed Power too long; you device may be turn off.
5. Tap the Pharos_JumpSPL.nb file, it must be tabbed while Camera & Power button are pressed.
6. After above, you should get grey background screen.
7. On ur pc quickly ( means make usb connection ) double click the ROMUpdateUtility.exe from the HardSPL dirrectory, and follow through the flashing process (what steps in flashing process?)
several question from me.
1) are this steps right?
2) what to do when get Grey background?
3) should i have to remove memory card and sim card?
4) did i have to backup my og rom? but how?
plz correct me >>>
Click to expand...
Click to collapse
Thanx its good!!!!!!!!!!!!!!!
success
very helpful and straight forward tutorial except i fond it hard to set camera to none since phone was in German but Google translate helped a lot.
People,
Problem: I want to upgrade my HTC Touch Viva to Win Mo 6.5.
Riders: I want to ensure that if required, I can flash the HTC original ROM that the company gave on phone. I have already downloaded original ROM from amarkangda 's thread.
My Status: I had an Asus P320 which I had upgraded to Win Mo 6.5. It involved copying the flash.bin (or whatever it was) to mem card, boot it with some keys pressed (service mode or somethin like that) and it took on from there.
Requirements: I am too confused with SPL and what not since this is my first HTC phone. Can anyone please provide a complete step by step (Bullet Point wise) guide as to what I have to do to upgrade the phone to Windows Mobile 6.5.
I tried the search function but was not able to find anything. If there is something and you know a link to it, please provide it. I will be highly obliged.
do hard reset fast
see the link for flashing ( http://forum.xda-developers.com/showthread.php?t=446446)
I Agree
I think that "The N00b's Guide to Flashing Opal" really is needed...
i mean, yes, there are a couple of guides with some information on "how to" but nothing complete and simple enough for noobs... there are a lot of new HTC users that have never flashed a phone before and have no idea how to do it, and even some experienced users on flashing other brands (mi personal experience, i used to flash motorola V3, Z6 and L7i) but get really lost when it comes to flashing HTC.
And after i learned i tried to help other new users but without success (see post 4 and 5 here http://forum.xda-developers.com/showthread.php?t=638911).
A complete guide should be made with all the terminology explained, the most common methods to flash, where to find stock roms, what kind of custom roms are there (ej. Light rom, cooked rom, what winmo ver is it using and pros and cons on all of them, etc.) all the software needed and a step by step guide with FAQ included. it should be community maintained to keep it always up-to-date.
I'll offer my help for anything needed and for Spanish translation.
@ mehulkarate
@mehulkarate
i'm sorry that this is just a copy and paste (and a bit of editing) from another post that i wrote, but i'll be easier for you:
I had the exact same problem when i first started to flash htc opal... didn't know how to do it, and didn't know what rom to use... maybe someone should create a complete, step by step guide (flashing opal for dummies) and post it as sticky...
ok, here it goes...
Flashing:
0.- if you'll be using a cooked rom (a modified Rom), you'll need to do a hardSPL. check here: http://forum.xda-developers.com/showthread.php?t=446446 (HardSPL is basically the way to remove the drm lock on the phone)
1.- Make sure that you have activesync if you are using windows xp or windows device manager if you are using windows vista and the latest version of .net framework installed on your pc.
2.- unzip the new rom files on a folder somewhere accesible (desktop for example)
3.- connect the device as an activesync conection, make sure the battery is charged 50% or more
4.- just run the RUU installer (Rom Update Utility), sometimes named CustomRUU.
5.- Follow the onscreen instructions.
YOU ARE DONE.
that's it... no complications, no special drivers, no weird commands or files to copy and paste. so simple. Just one thing: make sure you don't disconect usb during rom update.
so, resumed: Download Rom, Connect activesync, run RUU, done.
About what's the best 6.5 rom: PhamQuang. check for the latest on the rom development section. but different users will recommend different roms, so i'll recommend to try several before sticking to a particular one.
great...
su8044 said:
@mehulkarate
0.- if you'll be using a cooked rom (a modified Rom), you'll need to do a hardSPL. check here: http://forum.xda-developers.com/showthread.php?t=446446 (HardSPL is basically the way to remove the drm lock on the phone)
1
Click to expand...
Click to collapse
if he isn't going to use a cooked rom (modified rom) what should he be doing flashing???
neways...good of you to help noobies out.
@mohitkumar
there is an alternate way to do the same: which one is harder or easier is up to you
RUU (Rom Update Utility) via SDCard (your memory card) search for it in the forum.
Thanks Guyz.
So HardSPL has to be done, there is no escaping doing that?
Do I absolutely need to have DotNet on my PC? (I do not particularly like it, it slows down my PC)
Since I have already upgraded the Asus P320 from SD card, that will always be an option for me. Any ideas or links to rom which i can just put in sdcard, boot in service mode(or whatever with that volume down key pressed thingy) and it takes on from there, no hardspl etc? Just like i did for the Asus P320..
Especially if it saves me from going through installing .net on PC.
Yes
as far as i know: Yes and Yes... there's no scaping hardSLP because that's the one that'll let you install a modified rom... And .Net is needed because all update utilities will use it (HardSPL and RUU)...
But as Freelancer81 said, there's an alternate way to install a custom RUU through the SD card for the Opal too, i'll let you find that out on your own because i have never used that method nor have any previous experience on similar methods.... maybe you wont need HardSPL and .NET this way.
I'm searching for Volunteers to create the noobs guide to flashing opal... anyone willing to help PM me.
Hmm, so i will search for a ROM that can be installed from the card. May be, just may be, it can be done without the HardSPL thing.
If that fails, I will stick it up and go with process given here.
mohitkumar said:
Hmm, so i will search for a ROM that can be installed from the card. May be, just may be, it can be done without the HardSPL thing.
If that fails, I will stick it up and go with process given here.
Click to expand...
Click to collapse
As far as i know you cant install any cooked rom via SD card with out hardspl only official roms can be flashed via SD without hardspl. Bro if you are so afraid about ur warranty then i would suggest u to use default os for more time, or install hardspl u can retain ur warranty by flashing stock spl when needed.
Hi all,
Before I post here I have googled over the internet looking for a solution and i have read alot but no success, i have tried many different suggested solutions but all have failed, so that I'm here to ask who have faced a similar situation of me.
My HTC HD2 was having SPL-1.42 with its original stock ROM, then I decided to upgrade for a cooked ROM so that I installed the HSPL then it became SPL-1.42 HSPL, that was fine then I'm were able to upgrade to any cooked ROM, I have flashed my device with many different ROMs even the stock ones, every thing were very fine till I upgraded to the stock ROM of leo 2.10 "RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50 .07U_2.08.50.08_2_Ship" by via the MicroSD card and now stuck with the SPL-2.08 as shown in the attached photos.
I tried to flash again using the EXE file from my PC but it take very long time the fail even with the original stock ROM of my device, and I tried to flash using the SD card but it take very long time just showing a white screen labeled "loading..." and no more activity.
I attached some photos showing the problem.
I know its my fault because I did not read the warning in the text file that included with the ROM folder "Do not flash using the MicroSD"
So that, I'm looking for a solution... please help..
any help will be appreciated.
Thanks in advance..
Note: pardon me about my poor English.
xda_q8 said:
Hi all,
Before I post here I have googled over the internet looking for a solution and i have read alot but no success, i have tried many different suggested solutions but all have failed, so that I'm here to ask who have faced a similar situation of me.
My HTC HD2 was having SPL-1.42 with its original stock ROM, then I decided to upgrade for a cooked ROM so that I installed the HSPL then it became SPL-1.42 HSPL, that was fine then I'm were able to upgrade to any cooked ROM, I have flashed my device with many different ROMs even the stock ones, every thing were very fine till I upgraded to the stock ROM of leo 2.10 "RUU_Leo_1_5_TMOUS_2.10.531.0_Radio_Signed_15.34.50 .07U_2.08.50.08_2_Ship" by via the MicroSD card and now stuck with the SPL-2.08 as shown in the attached photos.
I tried to flash again using the EXE file from my PC but it take very long time the fail even with the original stock ROM of my device, and I tried to flash using the SD card but it take very long time just showing a white screen labeled "loading..." and no more activity.
I attached some photos showing the problem.
I know its my fault because I did not read the warning in the text file that included with the ROM folder "Do not flash using the MicroSD"
So that, I'm looking for a solution... please help..
any help will be appreciated.
Thanks in advance..
Note: pardon me about my poor English.
Click to expand...
Click to collapse
Heya i think ur stuck now on that SPL 2.08 havent heard any1 succeeding in putting hspl on it atleast from what ive read.
The cause is because u flashed that Tmous ROM trough MicroSD which overwrites the hspl.
I think if u had read the stickies more carefully this could be avoided but u can still flash Tmous roms some1 correct me if im wrong. hope this helps a bit
Thanks for replaying,
yeah you are right I have to be more careful but now its done and stuck with SPL 2.08.
anyway, I have tried to falsh it using Tmous ROMs but it faild, it says "this device is not suitable for this ROM" then exit, by the way, my device is the Asia version and I tried to flash it using the new officially updated ROM from htc.com but it also failed, it take very long time more than 15 minutes with no activity the I disconnect the USB from the device to save the battery charge, I'm afraid to stuck with a dead battery. When I disconnect it the upgrading software on my PC asking me to restart the device and reconnect it again then I did, the official upgrading software recognise the device then start to flash it but it stuck at beginning of the flashing process it just change the screen of the device to the back background with the progress bar its reading 0% and take very long time then i disconnect it.
by the way, is the any way to downgrade the SPL to 1.42 ?
any help please..
Thank you.
Last week I also face this problem. But I'm not using SD card to flash the room.
However, I backup my sd card then format the card, it become will afther this.
Same thing happened to me. This is what I did, removed the battery for about 10 seconds and flashed the original ROM. Then reflashed HSPL. It worked for me.
Thank you all for replaying..
I tried to do as you did but no success at all.
well, what next ?
Thank you
silentP said:
Same thing happened to me. This is what I did, removed the battery for about 10 seconds and flashed the original ROM. Then reflashed HSPL. It worked for me.
Click to expand...
Click to collapse
i believe to try to flash Original Rom from SD Card. not from PC.
i personally save my stock rom in SD card for future use in case of emergency.
Thanks for replaying
I tried to flash using the stock ROM is SD card but it failed, it shows a white screen with a "Loading..." word only, no activity.
Any help please..
You must use GoldCard repaired your device .Look here (Post 31 & 41) Repaired (with any Goldcard ) HD2 damaged when the flash rom TMOUS with memory card :
http://forum.xda-developers.com/show...=640183&page=4
You must change Tmous 2.07 ( in guideline article ) replaced by your ship rom 2.10.
same happened to xmoo....just letter xmoo about your problem...i hope he can help you....
ancola66 said:
You must use GoldCard repaired your device .Look here (Post 31 & 41) Repaired (with any Goldcard ) HD2 damaged when the flash rom TMOUS with memory card :
http://forum.xda-developers.com/show...=640183&page=4
You must change Tmous 2.07 ( in guideline article ) replaced by your ship rom 2.10.
Click to expand...
Click to collapse
Ok this is solution for that problem
no success yet..
but i'm confused about how to use the goldcard ?
I tried to you the attached goldcard.img from the post Id=640183&page=4 but no success.
is the goldcard.img dedicated to a specific device based on its CID ? or it can be used for any device ?
Thank you
Surely XDA Mods should take down the SD card method as there are about 10 threads a week of flashing the 2.10 ROM via SD card and getting stuck cause they don't read enough before hand - if the SD card method isn't there people won't brick their phones!!
{Solved} HTC HD2 stuck at beet loader...
Hi all,
finally I got my device running
by flashing it using Goldcard method, I bought the PSAS software and flashed it using Tmous 2.10 and now it is running fine.
well, the steps as the following:
1- getting the CID of the SD card that you are going to use for flashing you device, I used linux OS to get the CID of my SD card by:
linux host #>more /sys/class/mmc_host/mmc1/mmc1:*/cid
that will give you the CID of the SD card.
2- Start the PSAS software and must be registered then go to Calculations/Generators then select Generate HTC goldcard.
3- then click "Save Goldcard Image to file", rename it whatever you wanna name for example "goldcard.img".
4- Use HxD Hex Editor, then select Extras from the menu then Open disk image..
5- Use HxD Hex Editor, then select Extras from the menu then Open disk...
6- then click on "goldcard.img" tab then select the lines from 00000000 to 00000170 all the file content by high lighting it, then select Edit -> Copy.
7- then go to the disk tab the containing the sd card, then select the same addresses (00000000-00000170) then Edit -> Paste Write, then save the new content.
8- copy a leoimg.nbh to the SD card, its recommended to get it from the ROM that bricked your device. I'm used Tmous 2.10.
9- insert the SD card into your device then boot it to the bootloader by holding the volume switch down while your switching the device on.
10- wait for the menu to appear and follow the instruction to complete.
Thats work from me and should work for you.
by the way, I flashed US Tmous while my device is Asian.
Thank you all
and
Best regards
if you have your CID I may help you to generate the suitable goldcard.img for your device.
I think I've read that even though you are stuck on spl 2, now that you have it running you should be able to flash roms with sspl but you won't be able to change the radio.
HTML:
till now I'm not sure about the radio, any way, I'm trying to hack it, i successfully initiated the process of radio upgrading but it failed at 99%.
we gonna do it one day...
EddyOS said:
Surely XDA Mods should take down the SD card method as there are about 10 threads a week of flashing the 2.10 ROM via SD card and getting stuck cause they don't read enough before hand - if the SD card method isn't there people won't brick their phones!!
Click to expand...
Click to collapse
I tought I read througout numurous posts that the SD method is the prefered way to go?
xda_q8 said:
Hi all,
finally I got my device running
by flashing it using Goldcard method, I bought the PSAS software and flashed it using Tmous 2.10 and now it is running fine.
well, the steps as the following:
1- getting the CID of the SD card that you are going to use for flashing you device, I used linux OS to get the CID of my SD card by:
linux host #>more /sys/class/mmc_host/mmc1/mmc1:*/cid
that will give you the CID of the SD card.
2- Start the PSAS software and must be registered then go to Calculations/Generators then select Generate HTC goldcard.
3- then click "Save Goldcard Image to file", rename it whatever you wanna name for example "goldcard.img".
4- Use HxD Hex Editor, then select Extras from the menu then Open disk image..
5- Use HxD Hex Editor, then select Extras from the menu then Open disk...
6- then click on "goldcard.img" tab then select the lines from 00000000 to 00000170 all the file content by high lighting it, then select Edit -> Copy.
7- then go to the disk tab the containing the sd card, then select the same addresses (00000000-00000170) then Edit -> Paste Write, then save the new content.
8- copy a leoimg.nbh to the SD card, its recommended to get it from the ROM that bricked your device. I'm used Tmous 2.10.
9- insert the SD card into your device then boot it to the bootloader by holding the volume switch down while your switching the device on.
10- wait for the menu to appear and follow the instruction to complete.
Thats work from me and should work for you.
by the way, I flashed US Tmous while my device is Asian.
Thank you all
and
Best regards
if you have your CID I may help you to generate the suitable goldcard.img for your device.
Click to expand...
Click to collapse
I also bought PSAS and used my old TP to goldflash the card. Then flashed it with the TMOUS ROM using SD method. After that it game back to life and only way to flash other roms is using sspl. Only thing now is that I'm stuck with this TMOUS initial splash screen.
Also you can change the splash screen using SSPL,till now you can change what ever you wanna change using SSPL except the radio and SPL flashing.
now i'm looking for flashing the radio with some how.
tamAyT:
SD card method should be used a last resort and only if you know what you're doing - it's a million times easier to use HSPL and ActiveSync as if it fails it's easy to recover. I've never used the sd card method and after reading what it can do if you don't read into the ROM well enough it's not worth the hassle IMO
BladeKnight said:
same happened to xmoo....just letter xmoo about your problem...i hope he can help you....
Click to expand...
Click to collapse
HAHAHA.
For me changing the first 2 00 in de hex edit of the goldcard to 11 fixed the issue.
Radio 2.08 is greate.. SPL 2.08 is greate... So no problems a.t.m., if I need a stock rom I use SSPL...
But then again I hope someone comes with HSPL 2.x tho.
Hi Guys,
I'm kinda stuck here, hope you'll be able to help:
Situation is as follows:
I have an HTC Leo, and after 2 months of usage - got the white screen:
1. Tried soft reset - no good
2. Tried hard reset - no good
3. Cannot sync to PC with ActiveSync - does not detect the device
4. Can go to boot mode, but only with voulme down+soft reset button
5. Cannot sync in boot mode as well - there appears to be a "USB" writing at the bottom, (white line on boot mode) though ActiveSync does not detect via usb?
6. Tried to install HSPL2 - starts to install, never finishes, proggress bar goes up and down forever (on PC) - I believe device needs to be synced before installing?
7. Device is enabled in the device manager, though cannot explore - thus no access to SD card
8. Here we go, I seem to do something wrong, PLEASE HELP, I payed for the device about 400E in my country, stock warranty is not an option
9. HEEEEEEEEEELP
10. Thanks!!!
Try flashing the stock ROM for your HD2 via SD card. If you have a T-Mobile HD2 then go to T-Mobile.com to download the ROM you will have to enter the IzmEI number from under your battery to download it. If you have a international HD2 go to HTC.com and enter your serial number that is under your battery to getca list of ROMs you can download and install on your HD2. If the ROM is a .exe you will have to right click it and renamecthe file .zip to view the contents. After that follow the instructions in the thread linked below to flash the ROM.
http://forum.xda-developers.com/showthread.php?t=681317
[Q] Thanks
Hi, thanks for the info,
When I go to HTC homepage, i find "Rom Upgrades" - is that the same as the ROM itself?
Sorry if the q is dum ,I'm completely new in this
And also - does the card have to be empty (only ROM in) so that the phone boots it?
Thanks again
yasho1984 said:
Hi, thanks for the info,
When I go to HTC homepage, i find "Rom Upgrades" - is that the same as the ROM itself?
Sorry if the q is dum ,I'm completely new in this
Click to expand...
Click to collapse
Yeah that is what you are looking for. The ROM upgrades is the most recent official ROMs out for the HD2. Just make sure you use your serial number to make sure you get a ROM that is for your HD2 or you will not be able to flash it unless you get HSPL on your HD2. Also make sure the HTC site you are on is for your part of the world, your country or the country the HD2 originated from.
[Q] Hi again, last q
When I Explore the contents of the rom I see numerous files, and reading the instructions you linked tells me to rename an image. The ROM is an exe, so I renamed it to zip , explored and currently I see only one .nbh file:
RUU_signed.nbh
Should I rename this one to LEOIMG.nbh and copy this file only to SD card? Or rename and leave there, take the whole exe and put it into the SD Card?
Would that be sufficient to run the ROM in bootload?
Thanks again brother, you're a lifesaver
yasho1984 said:
When I Explore the contents of the rom I see numerous files, and reading the instructions you linked tells me to rename an image. The ROM is an exe, so I renamed it to zip , explored and currently I see only one .nbh file:
RUU_signed.nbh
Should I rename this one to LEOIMG.nbh and copy this file only to SD card? Or rename and leave there, take the whole exe and put it into the SD Card?
Would that be sufficient to run the ROM in bootload?
Thanks again brother, you're a lifesaver
Click to expand...
Click to collapse
Just take and copy the RUU_signed.nbh file make a copy ofcthe file and past it to your desktop and then rename it to LEOIMG.nbh then copy that file to the root of your SD card. All you have to have is the .nbh file but it has to be named LEOIMG.nbh.
You can also flash a radio, splash screen, and MAGLDR this way if need be. But you would still have to flash CWM via custom RUU via USB if you installed MAGLDR.
[HIHI]
Great - now "Radio fail" - update terminated... any ideas?
Exact error description:
00018003
LEOIMG.nbh - Fail
RADIO - Fail
Update Terminate
UPDATE FAIL
and this is an official HTC ROM?!?
yasho1984 said:
[HIHI]
Great - now "Radio fail" - update terminated... any ideas?
Exact error description:
00018003
LEOIMG.nbh - Fail
RADIO - Fail
Update Terminate
UPDATE FAIL
and this is an official HTC ROM?!?
Click to expand...
Click to collapse
Sorry I had to get some sleep, anyway I suggest you first make a backup copy of your SD card and then reformat your SD card using the Panosonic Mick SD card formatting software, just Google it you will find it. Do a full wipe of hour cardcand format it using Fat 32. Then copy the LEOIMB.nbh to your card and try it again. Also try to use a card no bigger than a 8GB as bigger SD cards are prone to give people problems when flashing via SD card. Note I did not say they will notcflash a ROM, bit they sometimes give people trouble.
Also I forgot to tell you this morning that if your HD2 says USB in the white bar of bootloader and it also says HTC USB sync in the device manager in the control panel of your computer, then you have a Sync connection to your computer but you can not use this connection for anything bit to flash different software to your HD2.
[Q] Hi Buddy, 10x for staying so long :)
Sorry brother,
I really appreciate your help so far.
Same Sh*t - even after FAT 32 format
When tried to upgrade with the official HTC ROM - "RUU_signed...." (not via SD) HTC boot screen appeared, but after 1% said : Image corrupted". It coud be that the stock rom sucks big time. May be try with some Artemis?
yasho1984 said:
Sorry brother,
I really appreciate your help so far.
Same Sh*t - even after FAT 32 format
When tried to upgrade with the official HTC ROM - "RUU_signed...." (not via SD) HTC boot screen appeared, but after 1% said : Image corrupted". It coud be that the stock rom sucks big time. May be try with some Artemis?
Click to expand...
Click to collapse
Yeah maybe you got a bad download of the ROM. If that was the only official ROM you could down load. I would try to download it againcand delete the first copy you downloaded, or I would flash HSPL. to my HD2 and then try to flash the stock ROM are a custom ROM. Custom ROMs are better than stock ROMs anyway. Just remember though if you have a warranty and you need to send your HD2 in for warranty work or exchange you need to revert your HD2 back to complete stock. This means ROM, radio, and SPL.