Hello,
I´ve got an issue with htc magic 32a, I read similar topics, but decided as it´s an specific case, to open a new thread... Here´s the whole story:
Phone originally:
HTC Magic / sapphire (32A) from Tim Brazil (bstar502)
BOOT LOADER: 1.76.0007
VERSION: 1.5 / CUPCAKE
FIRMWARE: 3.03.527.3 / 63.18.55.06HU_6.35.07.29
well, rooted the phone, no problems about it, but couldn´t get recovery recovery-RA-sapphire-v1.7.0H_32A.img to work, then I saw that hboot 1.76.xxx should use recovery-RA-hero-v1.6.2.img, and so I did it. Marvelous, recovery now working, selected hboot_1.33.2009_32A.zip, and flashed it from sd. oh, while phone was still working, made him a goldcard (kingston 2gb).
all seemed fine, but phone did not boot up, instead was hanging on 'htc magic', but could still enter fastboot. so I had the terrible idea to flash Engineering SPL 1.33.2004, which made it hang even earlier, and no fastboot available.
as a last attempt, I got rom from same cid as phone is, put it on goldcard, and hoped it flash, but.... nothing! goldcard with sappimg.zip inside, I reset it holding vlm down, but it´s the same as pushing only power button (tim logo on screen, and hangs in there).
so, aware of the situation, I ask the ones who can answer me for sure: do this phone have any chance to revive with 'normal' tools, or only by jtag?
br
Related
Ok - thanks for coming in and reading my post even though you could have skipped right on through.
I have purchased a used MT3G from craigslist (i know). I am a semi-knowledgeable "veteran" when it comes to rooting and flashing on the g1 - but the mytouch is totally new to me.
I have some SERIOUS SERIOUS concerns as to what my phone even is in the first place. I bought it with original TMobile packaging, phone says tmobile in the front and back - yet when I turn it on it's VODAFONE.
When I boot into recovery, I get the Triangle Exclamation with the phone. The rom is a 1.5 HTC rom and here is my fastboot info.
PVT 32B SHIP S-ON H
HBOOT - 1.33.0009 (SAPP30000)
CPLD - 10
RADIO - 3.22.20.17
May 8th 2009
HOWEVER - when I run the "one click root" - it says I have a 32A system. Eventually I followed the instructions for 1 click root using flash rec and flashed (downloaded) the Cyan 1.4.1a from the "recovery installer" (flashrec-1.1.2 2009-0909). They said my phone was 32A, I just went ahead and downloaded and installed - now I have the cyan recovery when I boot up my phone - I just can't flash ANY roms. I tried RAv 1.6 - for both 32B and 32A. 32A keeps rebooting my phone over and over, 32B just sits at the vodafone and hangs for 15 minutes.
After HOURS AND HOURS of reading the forms and the wiki - I'm at a complete impasse. I need some guidance. Do I have a 32A or 32B? Is it possible for 32A phones to show 32B in the fastboot? Some people need a "goldcard" to do this - I just used flashrec did I do something wrong? It seems as if some people are flashing roms with their regular SPLs - do I need engineering SPL - if so HOW do I flash SPL and radio without bricking.
I just want to flash some damn roms, or even get back to OEM and get my phone up to 1.6. It's such a bad feeling buying a phone, then bringing it home and you don't realize what you've gotten......I just want to get my phone rooted and start flashing roms and I've gotten this far.
ANY HELP GREATLY APPRECIATED!!!!!!!!
edit - the only way I've gotten my phone back to the stock HTC MAGIC rom is luckily upon first running of the CYAN recovery I did a nandroid backup and just restored to my backup after the failed rom flashes.
EDIT 2pm CST : I called T-Mobile, they can track your IMEI and Sim card every time you place a call - they CONFIRMED that my IMEI belonged to a TMOBILE MYTOUCH 3G and not any european phone. This leads me to my next question - is it possible to flash this HTC MAGIC rom onto a TMOBILE MYTOUCH 3G through fastboot, or something - WITHOUT a recovery, WITHOUT having root?
My MYTOUCH 3G is running VODAFONE everything, and it's definitely a EUROPEAN HTC MAGIC rom. Did someone install something on this phone before I got it. Please community - any help is appreciated.
A possible explanation is that someone followed Amon_RA's instructions partway through but did not finish. Specifically, they may have flashed the SPL, the recovery image for 32A and then a ROM for 32A. Since the phone is 32B, the recommendation is then to update the radio and recovery and ROM for 32B after it is rooted.
Perhaps this person rooted the phone, and then did not revert to 32B. Just a guess, though.
ok bro first lets calm down. everything is fine. all the information you need is right in front of you. first if its from europe it could be 32b and or 32a. so to check if you have root lets download a terminal app. if you dont have one pm and ill send you one. once we have that run it and type
su
if it asks for permission or just goes to
#
you are good. now type cat /proc/meminfo
for "MemTotal:" if it says 98024 or around there then you have a 32b. there that took care of what kind of board you have now we have radio and splash. your radio is .009. eng radio is .006. most likely the person that had the phone before only did have the steps. so go over them again with doing a "real" rooting. make a goldcard, get a good rec .img and have sdk working on your comp. if you need help i can help the best i can.
my touch 3g problem!! please help!!!
i bought a my touch 3g from craigslist. and when i turn it on it freezes up and says vodafone and it just stays there.. i need help to get it off can anyone help??? please
Turn it on while holding the Home key and tell us what you get? If you get a menu of options then you have a custom recovery image and you can flash a new rom ... if you just get an image of a ! then you have the stock recovery image.
Also turn it on while holding the back key, give us the information from that screen (also known as the fastboot screen) as this will tell us what recovery options are available to you.
I feel you man.
richboii8939 said:
i bought a my touch 3g from craigslist. and when i turn it on it freezes up and says vodafone and it just stays there.. i need help to get it off can anyone help??? please
Click to expand...
Click to collapse
I worked for T-Mobile and got a mytouch before launch. My MyTouch, During the 32B radio flash, fell off my desk, disconnected, and has been stuck where you are ever since.
doing MANY hours of research and trying VARIOUS different methods did not help. I since bought another, (and a nexus. DO NOT MISS THE MYTOUCH) rooted it and my original MT3G, is still stuck on Vodafone red boot screen, and has a hopefully semi-permanent place in the bottom of my shame drawer.
Mine will not respond to Goldcards, and is not picked up by ADB.
If you plug your phone in, on boot and it is recognized by ADB, then you have hope. If its completely shot like mine. I doubt you'll be able to revive it. Unless ive been missing something since July of last year. (I had it early lol).
If it is recognized.
I would...
-Get a 32B radio
-Open CMD in the radio's folder (Shift + Right click will add a button in your right click to Open Command Prompt There)
-Fastboot flash radio <insert file name here>.zip
-Adb will say "Waiting for Device"
-IF IT IS RECOGNIZED It should reboot into Fastboot and flash the Radio and you should be okay.
*Please correct me if I'm wrong. Im can root all day long, but i can barely explain it. XD*
There wasn't any info that was an exact fit for the Docomo, but I gave it a go.
It's a 32B SAP2000
It had a perfected SPL 1.33.0006, so I flashed a 1.33.0009 SPL.
It got to Fastboot, but now showed H instead of G and the radio was different.
Fastbooted into RA's 1.5.2 recovery.
Instead of applying my nandroid backup I thought I'd apply the radio from HTC site. The one for 32B.
Rebooted to the unboxing screen for 20 seconds, then back to HTC Magic splash screen.
Since then I can't get fasboot or recovery.
Putting in the battery causes the phone to instantly vibrate a little and come on.
Holding the different combinations of buttons whilst the cable is connected/unconnceted does nothing.
I can't issue fastboot commands via cmd prompt.
Hmm... this seems like a challenge, no? Anyone think they know where to even begin to de-brick this?!
No challenge, it's impossible! unfortunately once you've bricked it only HTC can help. Try to get it replaced if it's under warranty (tell them that you've tried to install an official update and that something went wrong).
No fastboot (back+power) or recovery (home+power) = dead phone
Shame. Ah well. Time to bid on another one!
This time I'll hunt down with Android 1.5; will make life so much easier!
Hi everybody,
I just got my 1.5 cupcake Magic yesterday from SFR (Vodafone french carrier). I discovered it had a perfect-SPL and used both tuts found on this forum to get over it. First I made my goldcard then used id to fix the perfect-SPL. I followed everything step-by-step. Everything went fine and my phone went from a 1.5 cupcake Vodafone with Google french rom, to a HTC 1.5 cupcake english rom with non-perfect SPL.
Now I try to flash with a rom by Luo (at SmartPhone France forums) wich is based on Ion.
I installed the SDK on my XP Pro SP3 PC, and the drivers form the SmartPhone France wiki, when needed by XP with the Magic connected on USB Debug mode and Fastboot mode. My SDK Tools folder is on the windows PATH of course, and I put the Amon_Ra recovery IMG in it. The Luo rom ZIP file is at the root of my freshly low-formated FAT32 memory card, and the card is back in the phone.
When I start in Fastboot mode and then type the
fastboot boot nameoftherecovery.img command line on my PC, it says it's loading the file.
Then on the phone screen a tiny green progress bar fills up from bottom to top in the top right corner of the screen, when full, the phone vibrates briefly, then restarts, show me a magnificent htc magic logo and stays like that forever. I never get a chance to get to the menu that I need to wipe then flash.
I guess I'm not bricked since I can boot normally and access the fasboot, and not in perfect-SPL anymore, but hell yeah I'm in some deep sh*t and fed up already as it's been 24hrs I had my phone and can't use it ...
Any clues you pros ?
Thanks in advance !
Then on the phone
try turning it off for a while and then turn on, Otherwise try flashing one of dwangs roms.If you have the same problem as i do i cant flash any modified boot.img over 2MB it says write image error thus when you flash its not actually flashing the boot.img its using the one previously on the phone
The problem is solved. VincentjuanFR has followed the tutorial from AmonRA to disable a perfect SPL. But this tricks installs a 32A radio on the phone whereas he's got a 32B. Then, the recovery for 32B cannot boot.
he used the recovery for 32A to flash a 32B radio and then his phone was fine again.
I just rooted my Mytouch a couple days ago and everything worked perfect and i did it without bricking my phone. I was trying to get the supercsdiv4 rom, but i needed to flash the lateset radio and heres where the problem started. the radio tried to flash was 2.22.23.02. I used the recovery image to flash it and then when i rebooted the phone it stayed stuck at the splash screen and i cant get into fastboot or recovery anymore. it just boot to the splash screen and stays there. I know i cant get my phone back but i want to know what i did wrong so that i dont ever do it again. maybe it was because the radio i had was a 32a radio and this radio i tried to flash might have been 32b but im not sure why that wouldn't work if my phone is 32b
here was my system
pvt 32b
Hboot 1.33.2005
radio 3.22.20.17
have you tried taking the battery out for a bit.. relax a while, then put it back in and try to get into recovery mode (home and power)
this actually happened yesterday and my phone was off the whole time so it has had plenty of time to rest. My phone is truly bricked
well im sorry to hear that, but i have no idea what you did wrong, unless you did flash a 32a over a 32b or the other way around, im sure that could really mess up the phone.
may be a useless idea but have you tried a hard reset
1. With the phone turned off, press and hold the HOME and BACK buttons.
2. Briefly press the END CALL/POWER button while continuing to press the HOME and BACK buttons.
3. When you see the screen with the 3 Android
images, release the HOME and BACK buttons, and then press the TRACKBALL.
i have no idea if it will do anything but might as well explore EVERYTHING.
Similar Problem (Partial Brick?)
Not to take anything away from clint1225 but
I have a similar problem and didn't want to start another thread.
I tried unrooting my devices using the method
described at theUnlockr.com. Everything was fine up until I tried using
their sappimg file (said it worked for all old magics).
At the hboot stage, it found the sappimg but the update failed.
However, the magic now says:
SPL-1.33.0006 (SAP50000)
Radio- 2.22.19.261
Ship S-On G.
It's a 32A version.
I had an engineering spl and 6.35xx radio before I attempted to unroot.
Oh I'm not able to access recovery but I can access
fastboot (computer can't find it though under "fastboot devices")
Other than that, it's stuck at the first splash screen.
Any advice/tips?
Sorry for the long post and thank you.
Good luck to you too, clint1225!
UPDATE *Similar Problem (Partial Brick?)*
In the adb, the serial number
of the htc magic is coming
up under "fastboot devices".
However, if I try to
flash a recovery for example, the adb
returns "remote access not allowed".
I've read about the gold card method
but my phone won't boot up properly
(stuck at splash screen) and I can't
access recovery. Only fastboot seems to be
working.
Any help is greatly appreciated.
Thanks!
Take it for what it's worth coming from a newb. But from my understanding if you can reach your phone with Fastboot your a NOT bricked. But this is what I have heard here on XDA, I haven't proven this myself.
Check around and hopefully with fastboot you can get your phone back. Good luck.
I did the exact same thing a few weeks back. I flashed a 3.22 radio over my 2.22 radio, thinking it's an upgrade but after it reboots, it wont get past the logo screen. I spent the whole day trying to find ways to recover it but cannot find any. Thank god I have warrenty on it so I went to the Tmobile store, told them I updated it and when it restart, it got stuck on the logo screen. They gave me a new phone and told me dont f-up this one. Now I'm afraid of updating my phone to the 6.something radio.
Update *Similar Problem (Partial Brick?)*...again.
MasterColdSoul and koolpre,
Thanks for the tips and luck!
I figured it wasn't a total brick so I searched
the whole day on google and xda.
What I can tell you is that I now have a functional phone.
I used the rogers "mandatory" update (2 sappimgs) to
get my phone (rogers 32a) working again (boots fully).
However, I now have the SPL 1.76.0010 which means
I've lost root functionality and it's harder to get root.
But I could use the phone to make a gold card and get root again.
Boy I'm glad this worked! I should have learned my lesson
but I will probably try to root, hehe!
Thanks to google search and xda community!
koolpre said:
I did the exact same thing a few weeks back. I flashed a 3.22 radio over my 2.22 radio, thinking it's an upgrade but after it reboots, it wont get past the logo screen. I spent the whole day trying to find ways to recover it but cannot find any. Thank god I have warrenty on it so I went to the Tmobile store, told them I updated it and when it restart, it got stuck on the logo screen. They gave me a new phone and told me dont f-up this one. Now I'm afraid of updating my phone to the 6.something radio.
Click to expand...
Click to collapse
just because the radio starts with bigger numbers doesn't make it an update. 3.22 was the old radio and 2.33.23.02 is the latest radio so you were actually downgrading your radio and thats why your phone brick. Just letting you know because you seem to be under the wrong impression. Dont make that mistake again. just do a little research to find the latest radio.
hi,
i need ur guys opinion,
story goes
i have Magic 32a unlocked version.
then i root it to android 2.2.1 using the old radio / hboot combo.
then, i thought i want to update to android 2.3.1
now here is where the problem begins.
i accidently flashed the 32b radio on the phone. now the phone wouldnt go past the HTC Magic logo.
to fix this, i download the mytouch3G sappmig.img file and completely flash the phone over.
when i open fastboot it still using the 32b radio / hboot but this time the os loaded fine.
i install superandroot and superoneclick on the phone to root it
after rooting i tried flashing 32a radio / hboot but it say not allow.
next step i tried installing custom recovery and finally manage to do it using the flashrec app. i installed 32a recovery but it failed to boot it. i tried installing 32b recovery and it run fine.
now from the recovery itself i tried flashing 1.76 radio and the recovery unpack the file just fine. but when it says reboot, the 'Box with arrow and phone outside' image appear for a sec and then dissapear.
after that my htc magic is completely dead. pressing any button, pluging in usb cable or charger yield no effect (like a brick)
have i completely bricked my phone? please help.
Sad to say this, but yes.
You just had a bad radio flash...
Try JTAG.
i tried again after leaving the phone overnight, these are the only thing iam able to do with the phone:
trackball + power = blue led
long press power = led blink red once
plug in charger = battery charge indication light on, orange and then yellow indicating the battery is full.
and thats about it. no other button combo works. and fastboot devices and adb devices booth shows no device.
anyone doing this JTAG repair service?
bump...
im having the same problem...just posted my issue here: http://forum.xda-developers.com/showthread.php?t=959938
i have the blue LED as well...
i googled how to make a JTAG cable...but its really past my level of competence...
were you ever able to get your phone fixed?
you found any solid step by step guide to make the jtag? please post the link here. i want to explore further. tq.
i was having the same problem...initially all went well, manage to change the from SHIP S-on to ENG S-off. i brick my device right after updated the rom to froyo and thereafter unable to boot. everytime i booted my magic, i only sees the RUU (fastbot) page. i cant do adb command. luckily the fastboot flash command still work.
i have try flashing with a lot of different images but always got stuck @ either
FAILED (remote: 42 custom id check fail) or FAILED (remote: 12 signature verify fail). never go beyond that...after going thru so much hassle of finding the right image, i finally manage to get it up and running. it flashes by ROM to enclair (2.1), good enough for me to use whatapp..
specification of my Magic is 32A S-O; radio 6.35.16.19; hboot 1.76.0010
this is how i "unbrick"
Download the SAPPIMG from shipped-roms.com, download Brasil_SAPPIMG_3.54.zip
place the file in android sdk folder, where fastboot resided.
make sure your device is fully charged...
boot your device and connect it to the usb, you will sees RUU USB.
type this command fastboot flash zip XXXXXXX.zip
i hope this help...