I'm trying to revert back to stock on my Epic. I previously flashed using Clockwork and wanted to try Odin this time around but when I put the phone into Download mode my computer doesn't recognize the device. I've tried multiple cables and USB ports including one on the board itself. I am using Windows 7x64 and have the 64 bit samsung drivers installed properly. If I do a battery pull and boot the phone normally the computer recognizes the phone no problem.
Any ideas?
ghsthntr said:
I'm trying to revert back to stock on my Epic. I previously flashed using Clockwork and wanted to try Odin this time around but when I put the phone into Download mode my computer doesn't recognize the device. I've tried multiple cables and USB ports including one on the board itself. I am using Windows 7x64 and have the 64 bit samsung drivers installed properly. If I do a battery pull and boot the phone normally the computer recognizes the phone no problem.
Any ideas?
Click to expand...
Click to collapse
I was having a similar issue with my MBpro, nothing would recognize my phone. Tried it on another comp and bingo. I think stuff is just finicky with USB ports. Lame-o.
ghsthntr said:
I'm trying to revert back to stock on my Epic. I previously flashed using Clockwork and wanted to try Odin this time around but when I put the phone into Download mode my computer doesn't recognize the device. I've tried multiple cables and USB ports including one on the board itself. I am using Windows 7x64 and have the 64 bit samsung drivers installed properly. If I do a battery pull and boot the phone normally the computer recognizes the phone no problem.
Any ideas?
Click to expand...
Click to collapse
when did u plugg ur phone in dowload mode?
try this ... load odin ... turn ur phone off!!! plugg it to the computure so when u see its charging for 30 sec. Then put the cellphone into download mode... and that should work
maldito.boss said:
when did u plugg ur phone in dowload mode?
try this ... load odin ... turn ur phone off!!! plugg it to the computure let it charge for 30 sec and the put it into load mode... that should work
Click to expand...
Click to collapse
Yea...this post made my brain hurt...and of course didn't change anything...but..thanks?
Here's another piece of info that may help nail down the problem...
Odin is able to see the phone if I boot into Clockwork recovery mode but because clockwork is up the phone can't receive a flash but Odin does see the phone with no problem. It just still won't see the phone when booted into download mode.
ghsthntr said:
I'm trying to revert back to stock on my Epic. I previously flashed using Clockwork and wanted to try Odin this time around but when I put the phone into Download mode my computer doesn't recognize the device. I've tried multiple cables and USB ports including one on the board itself. I am using Windows 7x64 and have the 64 bit samsung drivers installed properly. If I do a battery pull and boot the phone normally the computer recognizes the phone no problem.
Any ideas?
Click to expand...
Click to collapse
I use windows7 64 too. I encountered tons of problems when trying to flash my epic. first my computer doesn't recognize my phone in download mode. after i wipe out all the drivers and reinstall them. finally i get my computer recognize it under download mode, but Odin froze every time during the flash.
Finally, i tried on another desktop computer with windows XP. Everything went perfectly. So maybe you should try that too.
I cannot connect to my Epic in download mode on mac os x either.
I was trying to install a lag fix, and now all my phone will do when powering on is show switch between the normal Samsung screen, and another reading "Samgung GT I9000".
I can still boot into Clockwork Recovery. But OS X will not recognize my phone.
Either that, or Heimdall isn't recognizing it and won't let me flash.
Help! Any ideas?
Pirate-M.Lifnen said:
I cannot connect to my Epic in download mode on mac os x either.
I was trying to install a lag fix, and now all my phone will do when powering on is show switch between the normal Samsung screen, and another reading "Samgung GT I9000".
I can still boot into Clockwork Recovery. But OS X will not recognize my phone.
Either that, or Heimdall isn't recognizing it and won't let me flash.
Help! Any ideas?
Click to expand...
Click to collapse
Really!?! No one has any idea? Please guys, I'm just sitting here with a broken phone, there must be a way for me to fix this.
Pirate-M.Lifnen said:
Really!?! No one has any idea? Please guys, I'm just sitting here with a broken phone, there must be a way for me to fix this.
Click to expand...
Click to collapse
I had the same problem, I couldn't connect it to 3 of my pc's. 2 xp's and one windows 7. Turned out the port on the phone it self was broken, had to take it sprint and get it replaced.
Pirate-M.Lifnen said:
Really!?! No one has any idea? Please guys, I'm just sitting here with a broken phone, there must be a way for me to fix this.
Click to expand...
Click to collapse
If OS X isn't recognising your phone it's likely your phone has the buggy secondary bootloader. Samsung corrected the bootloader for at least the GT-I9000 JPA firmware but I'm unsure if they have done so for other devices or firmware releases.
Unfortunately the only solution then is to use Windows or Linux. If you don't have access to a system running either of these OS then I recommend downloading a 64-bit release (assuming your PC has a 64-bit CPU) of Ubuntu, then you can download the Heimdall binaries from my website and use it to recover your phone.
i had an extremely similar issue as to what you are having. I have 3 win 7 machines and 1 xp, none worked. I went to a friends house he has 2 win 7s and an xp also didnt work. I did a general search and found all kinds of crap. One dude something about using his chicks blackberry usb cord and suddenly it worked on any and all of the machines it had previously not worked. so at the time im reading this on my chicks laptop which has a damn blackberry cord attached to it chargin her evo(go figure) ... anyway u didnt need the whole story but i have nothing to do right now.
Point is everyone says try different cords, i say try the damn blackberry cord if you happen to have one or a friend that has one.
Benjamin Dobell said:
If OS X isn't recognising your phone it's likely your phone has the buggy secondary bootloader. Samsung corrected the bootloader for at least the GT-I9000 JPA firmware but I'm unsure if they have done so for other devices or firmware releases.
Unfortunately the only solution then is to use Windows or Linux. If you don't have access to a system running either of these OS then I recommend downloading a 64-bit release (assuming your PC has a 64-bit CPU) of Ubuntu, then you can download the Heimdall binaries from my website and use it to recover your phone.
Click to expand...
Click to collapse
Is it the hardware on the Macbook pro itself? or just the OS? in other words, If I were to partition my macbook with ubuntu would that work with heimdall? would it be able to recognize my phone while it's in download mode as opposed to OSX, which couldn't...?
ldartez said:
Is it the hardware on the Macbook pro itself? or just the OS? in other words, If I were to partition my macbook with ubuntu would that work with heimdall? would it be able to recognize my phone while it's in download mode as opposed to OSX, which couldn't...?
Click to expand...
Click to collapse
In this particular instance Apple haven't done anything wrong at all, both their hardware and software is fine. The issue is that Samsung are distributing secondary bootloaders that aren't complaint with the USB specifications.
Whilst that is annoying, the good news for you is that you can simply install Linux (Ubuntu etc.) or Windows on your Macbook and you'll be able to flash just fine.
Related
I've searched all over the posts and google and have yet to find a solution. I am a MAC user and trying to restore fascinate. I am stuck at Samsung screen. I can get into Clockwork Mod Voodoo.
When i did my last backup I never enabled USB Debugging. I can not ./adb into device, nor can I use ODIN on friends PC. (No Device) Same result with Heimdal "Failed to detect Device" I would just like to get back to stock. Is there a step by step guide to recover similar to ODIN get you back to stock but for a MAC. Or since i never enabled Debug mode I should just use my warranty?
When you tried Odin, did you have the battery out and put the phone in download mode?
Kevin Gossett said:
When you tried Odin, did you have the battery out and put the phone in download mode?
Click to expand...
Click to collapse
Yes, I did see the Yellow triangle Droid character w/ shovel
So, battery out and in download mode, Odin doesn't recognize? Hm
Kevin Gossett said:
So, battery out and in download mode, Odin doesn't recognize? Hm
Click to expand...
Click to collapse
I feel because I never enabled debug mode originally.
Does it recognize the phone at all? Maybe the drivers need to be updated
Sent from my SCH-I500 using XDA App
Morning, I'm attempting to resolve the same issue. I have the "Yellow Shovel" Andy but I can't get Odin to recognize the device.
The device was fine and Odin was working last night, however I do believe I did something ridiculous last night. I tried flashing my phone with a Nexus S rom and succeeded. HOWEVER, the only buttons that are recognized are the "Home" and "Menu" soft keys.
I can boot into the 2.3 Nexus S rom but I can't get the hardware to recognize anymore.
UPDATE: I managed to get the USB to recognize. I'm not completely sure how, it just started recognizing it after fidgeting with the cable. I'm not flashing it back to stock using ODIN and the following post.
http://forum.xda-developers.com/showthread.php?t=867648
UPDATE: The link above worked. I recommend using the stock USB cable that comes with the phone. Now that it's back.. I'm curious to know what I would have to change for 2.3 to work.. hm..
Kevin Gossett said:
Does it recognize the phone at all? Maybe the drivers need to be updated
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
Come to think of it I did update the drivers on my friends PC but there was an error installing drivers. He had a Windows XP 32bit device (Did install the 32bit drivers X86) Im going to try my other buddies PC he has Vista should that make a difference?
Soft Brick fixed
rolo12010 said:
Come to think of it I did update the drivers on my friends PC but there was an error installing drivers. He had a Windows XP 32bit device (Did install the 32bit drivers X86) Im going to try my other buddies PC he has Vista should that make a difference?
Click to expand...
Click to collapse
UPDATE: My buddy brought over his PC and got it restored! looking good now. We just updated the samsung drivers. restarted the machine. And it worked. Will update w/ the file he used. Thanks for the help and feedback.
Alright, so I've been trying to figure out why Windows doesn't recognize my phone in Download Mode (attempting to get EB13) and I've now realized it doesn't even detect it in Mass Storage mode (Windows tells me a USB device was not recognized when I connect it)
Any ideas?
I'm stumped here...
Note: tried it on both x86 and x64 versions of Windows.
Download the latest drivers. As for download mode areu trying to use odin?
Sent from my EB13 Samsung Epic
Check the "teeth" in where the cable connects to your phone. Some people have had them bend out of place.
MedicStuder said:
Download the latest drivers. As for download mode areu trying to use odin?
Sent from my EB13 Samsung Epic
Click to expand...
Click to collapse
Just downloaded them onto my x86 machine, and even when connecting my phone in normal mode (when it's fully on) it tells me device not recognized.
So at this point, I'm not even focusing on Odin, because nothing seems to be able to see my phone over USB.
I've even tried a different cable, but to no avail.
And yeah, I tried the Samsung EB13 download and I tried Odin. Neither could see it (just like Windows).
Other then this, it works perfectly fine. So it's not like I bricked it or anything.
Having the same issue. Tried multiple computers, reinstalling the drivers, and multiple USB cables. No luck. Makes things tough trying to get EB 13.
tanmack33 said:
Having the same issue. Tried multiple computers, reinstalling the drivers, and multiple USB cables. No luck. Makes things tough trying to get EB 13.
Click to expand...
Click to collapse
Alright, so I'm not alone here...
Windows actually seems to have just recognized it while powered up fully (and is currently installing the drivers).
Figure I'll let that finish and then try Download Mode again.
And then hope for the best I guess.
EDIT: It seems to be working now.
The Samsung EB13 utility is doing its thing in Download Mode.
Crossing my fingers it finishes without incident.
Uninstall drivers then install then reboot pc and phone then try. If reboot didn't solve the problem reboot phone and try again.
Epic 4g
Well, it seemed to be working.
But now my phone has a green screen and the EB13 utility is stuck on "FACTORYFS" and the progress bar says "Elapsed Time: 18sec.... 4%"
I really hope this didn't brick my Epic
anyone know where the drivers are for the epic
shud be somewhere on this site.. or on samsungs website.. its easy to just google..
Alright, Ive been browsing these forums ever since I got a Captivate and now I am trying to help a friend that has an Epic. They currently have dk28. Their Epic has always been Flakey on being detected on computers. We have tried three, it only gets detected on Mass storage on one of those and doesnt get detected in dowload mode on any of them. That being said, We cannot get back to stock via Odin, or use the Samsung official Update due to that it will not be detected in download mode. Can anyone tell me is there anything I can do at this point? Ive already tried 3 cables, uninstalling and re-installing drivers, etc... I am hoping maybe there is some way to get back to stock without odin, then from there getting to EB13 without the use of a computer. Thanks in advance and I look forward to posing here.....
Did you restart the computer at all?
usb debugging enabled?
i have trouble connecting sometimes and it's always solved by restarting the phone.
Basementboyz24 said:
Alright, Ive been browsing these forums ever since I got a Captivate and now I am trying to help a friend that has an Epic. They currently have dk28. Their Epic has always been Flakey on being detected on computers. We have tried three, it only gets detected on Mass storage on one of those and doesnt get detected in dowload mode on any of them. That being said, We cannot get back to stock via Odin, or use the Samsung official Update due to that it will not be detected in download mode. Can anyone tell me is there anything I can do at this point? Ive already tried 3 cables, uninstalling and re-installing drivers, etc... I am hoping maybe there is some way to get back to stock without odin, then from there getting to EB13 without the use of a computer. Thanks in advance and I look forward to posing here.....
Click to expand...
Click to collapse
Are you placing the phone in Download mode???
****Ensure USB Debugging is Enabled.
Download mode:
1. power off the phone.
2. Press 1 + Power button together
otherwise, I would highly recommend to:
1. uninstall drivers
2. restart the PC
3. install the Samsung drivers
4. restart
5. try connecting the phone (while powered on) and letting the PC recognize it.
6. Once drivers are installed, unplug the USB cable and Power off the phone
7. Place the phone in download mode and reconnect the USB cable and let the secondary drivers install.
8. unplug and reboot the phone, and restart the PC for last time.
Try Odin now, remember you need the phone in Download mode to use Odin.
Note: Yes I know I send the OP to restart many times his PC but, with windows we can never "restart" to much...
Couple things:
What OS are you using? If vista or 7, plug it in in debugging and go to the devices window in control panel, see if there is a samsung device there. If there is, right click and look at properties..check to see if there's an adb driver. If you see other drivers but not adb then its matter of getting the drivers to install somehow.
Second, there IS a full di18.zip, and a modem updater.zip to di18 as well, both flashable in CWM..(I believe its in a thread started by noobnl, its kinda old)...you might only have to do the .zip though since you'll eventually be going to the eb13 modem. I don't know for sure.
But be wary: switching android versions with CWM can be dangerous. I know it sounds counterintuitive, but it can actually be riskier than using odin. I would say use this only in last resort.
If you decide to do this, MAKE SURE you have the full download (I say download twice and compare the sizes just to make sure), have a full battery and keep it plugged in, and do your 3x wipes
Good luck
Sent from my baked and emotionless SPH-D700
megabiteg said:
Are you placing the phone in Download mode???
****Ensure USB Debugging is Enabled.
Download mode:
1. power off the phone.
2. Press 1 + Power button together
otherwise, I would highly recommend to:
1. uninstall drivers
2. restart the PC
3. install the Samsung drivers
4. restart
5. try connecting the phone (while powered on) and letting the PC recognize it.
6. Once drivers are installed, unplug the USB cable and Power off the phone
7. Place the phone in download mode and reconnect the USB cable and let the secondary drivers install.
8. unplug and reboot the phone, and restart the PC for last time.
Try Odin now, remember you need the phone in Download mode to use Odin.
Note: Yes I know I send the OP to restart many times his PC but, with windows we can never "restart" to much...
Click to expand...
Click to collapse
Did everything up till 5, and that did not work because the computer would still not recognize the phone. What now?
squshy 7 said:
Couple things:
What OS are you using? If vista or 7, plug it in in debugging and go to the devices window in control panel, see if there is a samsung device there. If there is, right click and look at properties..check to see if there's an adb driver. If you see other drivers but not adb then its matter of getting the drivers to install somehow.
Second, there IS a full di18.zip, and a modem updater.zip to di18 as well, both flashable in CWM..(I believe its in a thread started by noobnl, its kinda old)...you might only have to do the .zip though since you'll eventually be going to the eb13 modem. I don't know for sure.
But be wary: switching android versions with CWM can be dangerous. I know it sounds counterintuitive, but it can actually be riskier than using odin. I would say use this only in last resort.
If you decide to do this, MAKE SURE you have the full download (I say download twice and compare the sizes just to make sure), have a full battery and keep it plugged in, and do your 3x wipes
Good luck
Sent from my baked and emotionless SPH-D700
Click to expand...
Click to collapse
Im Using Vista and No Drivers were there.... And I guess I may be at the last resort point. Full details?
some people have tried changing usb ports and it will work.
anyone else having problems not being able to connect phone to comp. can try this method but not sure if this works on the dk28.
what you could do is to remove the microsd card from phone use the adapter that came with it and put sd card into your laptop or if you have a external hub then your microsd will just be a storage devise then download the mac version of froyo from samsung (sorry i can't post outside links yet)but it is the samsung support downloads then search for this SPH-D700ZKASPR click on the software then download the mac version to comp. then copy and paste what you downloaded to the root of the sdcard (the first one you see when you open the sdcard) then put card back in phone, power off phone wait untill all lights go off press volume down, camera and power at same time. then in recovery chose update.zip from sd by using volume buttons to chose what you want to do then press the home button to start.
I had issues with mine taking the update (and issues with it beforehand) and getting it recognized on two different computer, multiple times, it seems completely random whether or not it would work sometimes.
thepervster said:
some people have tried changing usb ports and it will work.
anyone else having problems not being able to connect phone to comp. can try this method but not sure if this works on the dk28.
what you could do is to remove the microsd card from phone use the adapter that came with it and put sd card into your laptop or if you have a external hub then your microsd will just be a storage devise then download the mac version of froyo from samsung (sorry i can't post outside links yet)but it is the samsung support downloads then search for this SPH-D700ZKASPR click on the software then download the mac version to comp. then copy and paste what you downloaded to the root of the sdcard (the first one you see when you open the sdcard) then put card back in phone, power off phone wait untill all lights go off press volume down, camera and power at same time. then in recovery chose update.zip from sd by using volume buttons to chose what you want to do then press the home button to start.
Click to expand...
Click to collapse
Any confirmation on whether or not this is safe and will work???
this is how i put different updates in zip format on my phones sometimes my comp hesitates, so to make sure they go on sd card all the way this is how i do it. its doing the same as mounting phone in storage mode.
but i went back to stock ecliar di18 2.1 a couple days ago and i had no prob.at all.
i just didn't want to wait for the ota and i found the update.zip on the samsung website yesterday at about 6 pm. downloaded it and it worked great. was rooted this morning at 7am and am good to go.
thepervster said:
this is how i put different updates in zip format on my phones sometimes my comp hesitates, so to make sure they go on sd card all the way this is how i do it. its doing the same as mounting phone in storage mode.
but i went back to stock ecliar di18 2.1 a couple days ago and i had no prob.at all.
i just didn't want to wait for the ota and i found the update.zip on the samsung website yesterday at about 6 pm. downloaded it and it worked great. was rooted this morning at 7am and am good to go.
Click to expand...
Click to collapse
I dont see how this is going to help me since I am not on stock....
sorry, what i was saying for you was to change ports. i guess what should have been asked is are you rooted or do you just have the unofficial dk28 on it from dec. and have you removed any of the bloatware?
Yes change USB ports. The ones in the front normally don't work. You need one directly on the mortherboard
thepervster said:
sorry, what i was saying for you was to change ports. i guess what should have been asked is are you rooted or do you just have the unofficial dk28 on it from dec. and have you removed any of the bloatware?
Click to expand...
Click to collapse
I tried changing ports multiple times. I got a new cord, and now it finally detects the phone in regular mode but it will not in Download mode or when I have USB debugging on. Any more ideas anyone?
Basementboyz24 said:
I tried changing ports multiple times. I got a new cord, and now it finally detects the phone in regular mode but it will not in Download mode or when I have USB debugging on. Any more ideas anyone?
Click to expand...
Click to collapse
Hate to ask, but did you follow the instructions EXACTLY as the SW Updater tool says? Pull battery (next) - Download mode (next) - plug into PC (next) - Pull battery (again) (next).
One of the steps the tool does has to do with installing drivers... you mentioned Vista, but is it 32 or 64 bit? Have you tried a different PC?
Whosdaman said:
Yes change USB ports. The ones in the front normally don't work. You need one directly on the mortherboard
Click to expand...
Click to collapse
I have the exact issue with my phone. I can only connect to my computer using the back usb ports (off the motherboard). I'm on windows 7. If you haven't, give that a shot. Even try uninstalling the drivers, connecting to the back usb ports and see what it does.
Saw someone post about Odin only working when they flipped the phone face down - thought it had something to do with the accelerometer. I suspect that in that case it might just be a bad connection and flipping the phone over made the contacts work. Worth trying though it you are desperate.
Ok so. I bricked my gt-i9505, and i have tried everything to try and fix it. The problems are as follows:
Phone wont turn on
Wont boot to recovery mode
Odin, Kies and pc wont recognize phone
The things i did that got me to a bricked phone are i flashed paranoid android onto the phone and tried to flash gapps full modular, it wasnt working, clockworkmod gave me a status 6 error and so i decided to use mobile odin to flash it as soon as it began the phone crashed and it wont turn on anymore. i am able to go into download mode
I need some help if anyone can help. I dont know what to do.
Sir,
Please wait until mods will move this thread to the device specific forum.
Stand by
Until then read/ask in this thread: How to Unbrick Samsung Galaxy S4?
Good luck
mujtabay said:
Ok so. I bricked my gt-i9505, and i have tried everything to try and fix it. The problems are as follows:
Phone wont turn on
Wont boot to recovery mode
Odin, Kies and pc wont recognize phone
The things i did that got me to a bricked phone are i flashed paranoid android onto the phone and tried to flash gapps full modular, it wasnt working, clockworkmod gave me a status 6 error and so i decided to use mobile odin to flash it as soon as it began the phone crashed and it wont turn on anymore. i am able to go into download mode
I need some help if anyone can help. I dont know what to do.
Click to expand...
Click to collapse
If the phone won't turn on at all you might be boned.
Odin and all that obviously require you to be able to boot to download mode.
Are you positive the battery is good? Could you find another battery to try?
Does the charging light come on when its plugged in? Are there any signs of life at all?
Skipjacks said:
If the phone won't turn on at all you might be boned.
Odin and all that obviously require you to be able to boot to download mode.
Are you positive the battery is good? Could you find another battery to try?
Does the charging light come on when its plugged in? Are there any signs of life at all?
Click to expand...
Click to collapse
I think it does turn on because the phone does continue to heat up but its just a black screen also i can put it into download mode and it stays there without being plugged into charge. I'm not sure about the battery ill have to check that out. ill get back to you.
It sounds like you dont have recovery or a rom installed at all.
To fix that you need odin. If the PC wont recognize the phone that is a problem. Did you try a different USB cord to connect to the PC? They are not all created equal.
Skipjacks said:
It sounds like you dont have recovery or a rom installed at all.
To fix that you need odin. If the PC wont recognize the phone that is a problem. Did you try a different USB cord to connect to the PC? They are not all created equal.
Click to expand...
Click to collapse
yes i have used both the original one that came with the phone and the s5 one that my brother has, i have had no luck.
my phone shows up as "msm8960" or mtp usb device also it it device driver software was not successfully installed.
[UPDATE] i have found something similar to odin called JOdin3 that connects to my phone, through this i will try to flash a stock firmware, downloaded from sammobile, and see what happens.
Odin doesn't work without the drivers, and since you had an issue with the drivers that would explain why Odin doesn't work yet JOdin3 does.
Strephon Alkhalikoi said:
Odin doesn't work without the drivers, and since you had an issue with the drivers that would explain why Odin doesn't work yet JOdin3 does.
Click to expand...
Click to collapse
I installed the samsung drivers several times and it still wouldn't connect to the pc, i also installed kies and it still wouldn't work, but it was working before i bricked my phone. i have fixed my phone through JOdin3.But thank you everyone for your help.
Will it connect now through Odin or Kies?
Strephon Alkhalikoi said:
Will it connect now through Odin or Kies?
Click to expand...
Click to collapse
No it still wont connect to either but the computer does recognize the phone.
MTP is built into Windows, so the fact the PC detects the phone is a good sign. The entire problem you're having seems to hinge on your PC rejecting the Samsung drivers, which are absolutely required for Odin to function. Those drivers should have no problems installing, and I have successfully installed them on both Windows 7 (x64) and Windows 8.1 machines so I know the installer does work.
There could be many reasons as to the source of your problem, such as a corrupt file or registry entry from when the phone soft-bricked. You want to take a closer look and do some detective work here. Uninstall the drivers if you haven't already done so. Clean out the PC with CCleaner. Even attempt a reinstall of the drivers in the PC's safe mode. Regardless of what you choose to do, if you ever wish to use Odin, you'll need to get this resolved.
Strephon Alkhalikoi said:
MTP is built into Windows, so the fact the PC detects the phone is a good sign. The entire problem you're having seems to hinge on your PC rejecting the Samsung drivers, which are absolutely required for Odin to function. Those drivers should have no problems installing, and I have successfully installed them on both Windows 7 (x64) and Windows 8.1 machines so I know the installer does work.
There could be many reasons as to the source of your problem, such as a corrupt file or registry entry from when the phone soft-bricked. You want to take a closer look and do some detective work here. Uninstall the drivers if you haven't already done so. Clean out the PC with CCleaner. Even attempt a reinstall of the drivers in the PC's safe mode. Regardless of what you choose to do, if you ever wish to use Odin, you'll need to get this resolved.
Click to expand...
Click to collapse
yeah ill definitely try to fix the problem because odin is such a great tool. i have uninstalled and installed the samsung drivers but i'll go search the net and what not to try and find a fix. odin was working before when i flashed the stock rom and changed something to mtp and adb (i think i put in an ussd code or something (*#0808#) and through that i was able to use odin) but because the wifi wasn't working on the stock rom, i flashed a custom rom to fix the wifi problem but was once again greeted with the odin problem.
Okay so here goes. I've looked at the forums searching far and wide for anything that may help.
The problem is I have an S4 that had some battery problems. (swollen) so i replaced it out for a new one. The shop that I bought it from claimed that it was an original replacement battery (I live in Pakistan so finding an original battery was hard for me). So the phone worked fine for about half a month and now it's acting weird.
1. It seems to be stuck on a boot loop. but sometimes will start and run for a few minutes (random amount of time) and then go back into the reboot phase.
2. the phone does not go into recovery mode. The recovery screen pops up for a second followed by a no command screen and then phone goes back to boot loop.
3. the phone doesnt go into safe mode either. So i cant check if its a app related problem.
I tried to then flash a new recovery or the stock rom. The phone doesn't connect to odin/ nor Dr.fone for android.
-> Windows doesn't install the MTP drivers even though i have the latest version of KIES installed.
-> I have checked with a replacement battery the problem still persists.
Please HELP!!
Boot it into download mode, then try connecting it to a PC.
@GDReaper
The phone goes into download mode but the computer doesn't recognize it. It doesn't connect to odin and it says mtp drivers aren't installed..
T3R3NC3 said:
@GDReaper
The phone goes into download mode but the computer doesn't recognize it. It doesn't connect to odin and it says mtp drivers aren't installed..
Click to expand...
Click to collapse
Did you install the Samsung drivers? Windows won't do it by itself.
GDReaper said:
Did you install the Samsung drivers? Windows won't do it by itself.
Click to expand...
Click to collapse
yes I have samsung Kies installed, I also tried to install the drivers separately.
T3R3NC3 said:
yes I have samsung Kies installed, I also tried to install the drivers separately.
Click to expand...
Click to collapse
Then try a different USB cable.
Try a different USB port, different computer, and different OS.