Related
--
thats how mine is but in the bottom. not a big deal but i did feel it
several people reported the same thing before. screen not flush all the way around. there's no adhesive, the screen slides out of the outer sleeve if you remove the screws in back.
Oh...
--
mine does it on the bottom.
it feels like there is a slight gap in between the bottom bezel and the screen.
It's not a problem at all, but it sure is annoying at times.
On the left side of my HD2 the screen is easier to push in at the top and bottom, but it takes a lot of pressure to make it "squeak".
If I had a cosmetic issue, you can bet I would be on a waiting list to get a replacement. The looks on these phones are nearly as important as the performance, IMHO.
oh i deff agree, @op, if you only just got it id be trying to take it back.
Same on mine at the bottom - just barely - if you slightly press between the usb and headphone jack you hear a slight (guess it sounds like) a click and you feel it slightly move. When the usb jack is plugged in it stops Some play and I don't think its worth returning - also don't think it will get worse. Case materials should have been a little more rigid. Think if you get a hard shell case or aluminum skin - when they become available you won't notice it. Talking to other guys with the HTC branded Euro version their build quality is a bit better. Think its pretty much the same with all HTC stuff - their branded models (TYTN TYTN II etc.) were build better than the AT&T versions - they also cost a lot more because they aren't subsidized.
Personally feel the HD2 of all the MS phones with the exception of the HTC TYTN I is the most solid. The Fuze which I just got rid of was probably the worst. The case was ok but the front keypad was pure junk - out of the box the thing felt like it was going to break and it never sat "square" in its opening. The USB ports on all of them were really weak and were super loose out of the box. The slide out keyboards always loosened up and had too much play.
stim141 said:
Personally feel the HD2 of all the MS phones with the exception of the HTC TYTN I is the most solid. The Fuze which I just got rid of was probably the worst. The case was ok but the front keypad was pure junk - out of the box the thing felt like it was going to break and it never sat "square" in its opening. The USB ports on all of them were really weak and were super loose out of the box. The slide out keyboards always loosened up and had too much play.
Click to expand...
Click to collapse
For me, the Touch Pro 2 has top honors when it comes to "feeling" solid. My sister dropped it the other day and cracked the bevel, with a large triangle missing near the volume rocker and three other cracks on the bottom, top and opposite side.
I am encouraging her to return it and claim the insurance, but since there is no change in the quality of the phone's operation, she wants to keep it.
Again, for me, the TP2 seems more solid than the HD2, but the HD2 is very well-built compared to other phones. I am so paranoid about even putting my phone down on a hard surface, due to the sharp edges of the camera mount and the light metal case.
I will be installing my new invisibleSHEILD as soon as sirphunkee and I can make the time to meet somewhere clean (I have a 2yo at home ). I imagine my paranoia will drop a bit then...
I dropped my phone while working out at the gym.
I was on the treadmill, and dropped the phone from my hand to the treadmill belt, then it flew out (i was running pretty fast at speed 7) and ended up hitting the wall behind me. Well, I freaked out and ran over to check on the phone.
Even though I had NO protection, the phone was perfectly fine. Only a tiny scratch that's barely visible on the top left bezel, and everything was fine.
I really was surprised at the sturdiness of the phone.
Snarksneeze said:
For me, the Touch Pro 2 has top honors when it comes to "feeling" solid. My sister dropped it the other day and cracked the bevel, with a large triangle missing near the volume rocker and three other cracks on the bottom, top and opposite side.
I am encouraging her to return it and claim the insurance, but since there is no change in the quality of the phone's operation, she wants to keep it.
Again, for me, the TP2 seems more solid than the HD2, but the HD2 is very well-built compared to other phones. I am so paranoid about even putting my phone down on a hard surface, due to the sharp edges of the camera mount and the light metal case.
I will be installing my new invisibleSHEILD as soon as sirphunkee and I can make the time to meet somewhere clean (I have a 2yo at home ). I imagine my paranoia will drop a bit then...
Click to expand...
Click to collapse
My TP2 fell out of my hand in a parking lot, the thing didn't hit hard, but it left a small scratch on the screen (it was visible, but wasn't too obvious) and then some nicks at the corners of the device. It did look used. I returned it to T-Mo (I was still within 14-day remorse period) and used the money I got back to get an HD2 instead (for some reason I didn't qualify for either the full or the 11 month upgrade price, only 50 bucks discount... now that I think about it, I should have gotten it at full price, also, the day after it arrived (ordered online) T-Mo came out with the 2 for 1 smartphone, but alas, a new line was needed and I had no use for it).
I've dropped my HD2 at least 4 times since and there's not a nick on it. I figure the glass screen helps (as opposed to the TP2's plastic), even if it's a finger print magnet. I also have no problems with the screen or bezel being uneven, even after dropping it, nor have I had any single of the problems people complain about, so, go figure, I got the perfect production HD2.
Whew.... OK. Soooo glad to hear this isnt only my device. Mines is on the bottom. I also dont see it getting any worst and its so minor right now its probably not worth the hassle of returning. I tend to keep the gel case on it anyway..
thrashingdeth said:
thats how mine is but in the bottom. not a big deal but i did feel it
Click to expand...
Click to collapse
x2 same as mines.
--
I had an issue with mine creaking, on the bottom. Mainly when I was pressing the start key, or back. Got a replacement and it seems better. For a phone seriously delayed I don't get how the quality is so terrible.
my first hd2 the camera lens started to rattle tmobile replaced it
Tm5078 said:
my first hd2 the camera lens started to rattle tmobile replaced it
Click to expand...
Click to collapse
Was it the camera lens or the casing around the camera?
After watching the tear-down video I could see how the camera casing could be improperly installed and loosen after a bit of handling, but I thought the lens was pretty solid...
--
JWang158 said:
Seriously, this phone is turning out to be pretty half baked.
Click to expand...
Click to collapse
I disagree. Not sure if I got lucky or not, but my phone is in perfect condition despite being a month old and spending most of that time in my back pocket.
I've sat on it countless times, dropped it from my hand to the floor twice and dropped it from the car holder to the console in my vehicle so many times I can't count.
The only problem I have is with the SMS freeze, and I've solved 90% of that by keeping my inbox clean. If I have the money for a class 6 microSD card, I'd bet on having solved the other 10% of my problems.
Since upgrading my radio, I don't have any problems with dropped calls, missing texts, loss of 3G or any of the other popular issues that seem to be plaguing the new owners.
Since bad news always travels faster and wider than good news, one simply can't infer from the issues being discussed here that they are the norm. I would suspect a very small percentage of the HD2 owners frequent the forums here, and of those another small percentage are having hardware issues.
I've been through a few of these new phone releases here in the past and from my experience I would say that this is pretty normal for the first few months of a phone's release. In another month or so there will be a firmware upgrade to fix the freezing and icon switching, then a lot of the issues will switch from hardware to software. Soon after that, I expect everyone will be clamoring for the release of a Windows Phone 7 ROM, followed a few months later by a newer, faster phone that everyone will be switching to. A cycle, vicious but almost predictable.
I know there are plenty of threads about G2 hinge issues, but I'd like to know about your Desire-Z keyboard hinges now that it has shipped.
I've just received my second Desire-Z this morning and it's probably worse than the first one. If pick up the phone, absolutely horizontal, from a table just by holding the upper section, the keyboard just falls half-open. Surely it shouldn't be like this? Here's a quick youtube video I took of my first phone:
Just wondering if I've been really unlucky, or are they basically all like this? I really hope not...
Andre
Mine does exactly the same. I'm not sure if this is normal or not, but I'm not very happy with it.
My other concern is that the screen wobbles back and forth when I have the phone closed if I tap on the left and right edges.
I think this is probably a design flaw rather than a specific device problem. You'll probably find they're all the same
Sent from my HTC Vision using XDA App
Cant quite tell what the angle is in the video.
If I pick up mine by just the top piece then it droops, but doesn't slide out.
If I hold it upside-down by the base it droops, but can't slide.
Whenever I pick up the phone though I hold it by the base, so in normal use it's perfectly fine.
I'm basically assuming that the spring should be just strong enough for the phone to hold itself together (i.e. without the keyboard dropping away at all) when it is gently lifted up from a flat surface. That's the benchmark I would want to see anyway, and neither of mine will do that.
I might take this up with HTC and see what their view on it is - I just hope they don't do an Apple and patronisingly say "you're holding it the wrong way".
Andre
I've just sent off an email to superEtrader asking for a refund as I'm not happy.
I hope they take it back without any hassle since their website says I can't return it if its been opened. Someone on here kindly pointed out the Distance Selling Regulations say I can open it and play with it (I have the PDF stored on my PC!), but I don't want to have that sort of hassle.
my phone has the same problem as the video.
Also, the screen slides down when im lying down, holding the phone by the keyboard.
My phone isnt quite a loose as in the video, but it does droop if I pick it up by the top section rather than the base & also if I am lying down and hold by keyboard it will start to shut... I kinda expected to have a loose hinge based on reviews that I had seen for G2 & at this point its only a very minor niggle, so I wont do any return until I find out there are Desire Zs out there that actually have a firm hinge.
On another note, I noticed yesterday that the black backing of the keyboard is a bit bubbly.. Im hoping that the backing wont start coming away down the road... but I guess only time will tell.
I found it hard to do what was shown on video, I never grabbed phone like this before. It never opened on its own even slightly. Also owned TP2 and never held it by the screen. I dont think people would actually ever hold it like that.
No offense to anyone, I just dont see any issues with my hinge. I know it opens when I hold it like on video or upside down, but If I havent read some posts, I would never try it.
This is just my personal opinion on the "hinges"
The design is for the way we hold and use our phones.. I feel for you bro, but noone holds their phone at the angle your showing this at..
I have had no problem at all yet with the everyday use of this beast)
JD
Honestly, at first it bothered, but really, it really starts to make sense for me now how it acts. If our hinge would be stronger, it'd be more difficult to open it and might have us actually break it.
Also, when I hold it while typing, I instinctively put my index fingers along the side of the keyboard/screen (once it is opened) and type with my thumbs. That way, it's impossible for the screen to fold back in closed position.
When I pick up my phone, I really don't pick it up by only one of the parts (screen/base). It's actually quite heavy at 180g and if I don't want to drop it, I rather pick up nicely and firmly.
So, really, after 4 days with my phone, the thing that bothers me more now isn't the screen, but the weight difference between my old Samsung Galaxy S (with gel back) and the Z.
Actually, funny anecdote, while playing Angry Birds, I actually opened the keyboard so I had a better grip on the phone.
daft.71 said:
Honestly, at first it bothered, but really, it really starts to make sense for me now how it acts. If our hinge would be stronger, it'd be more difficult to open it and might have us actually break it.
Also, when I hold it while typing, I instinctively put my index fingers along the side of the keyboard/screen (once it is opened) and type with my thumbs. That way, it's impossible for the screen to fold back in closed position.
When I pick up my phone, I really don't pick it up by only one of the parts (screen/base). It's actually quite heavy at 180g and if I don't want to drop it, I rather pick up nicely and firmly.
So, really, after 4 days with my phone, the thing that bothers me more now isn't the screen, but the weight difference between my old Samsung Galaxy S (with gel back) and the Z.
Actually, funny anecdote, while playing Angry Birds, I actually opened the keyboard so I had a better grip on the phone.
Click to expand...
Click to collapse
+1000000
QUOTE:Also, when I hold it while typing, I instinctively put my index fingers along the side of the keyboard/screen (once it is opened) and type with my thumbs. That way, it's impossible for the screen to fold back in closed position:END QUOTE
I could not have put it better myself....
JD
I think I'll just keep mine until we get confirmation that better-designed Desire Zs have been produced. The replacement is from HTC and not my supplier, so I should be able to do it at any time during the next 2 years... right?
Mine is pretty solid - I even text in bed and it doesn't fall. I have opened the keyboard once or twice by accident, which is quite funny..
Desire Z on Bell Canada Hinge problem
I have already gone through two DZ's and both have the "weak" hinge. Thankfully mine does not do what is shown in the Video in post #1, thats definitely a defect in my opinion. Just to compare notes on a relative basis here is what mine does.
When the phone is closed I turn it sideways (landscape) lift it from the bottom and then press on the left and right edges with my thumbs. The screen snaps nicely into place. If I then grap the device by the top two corners of the screen and lift it straight up and hold it perfectly horizontally the keyboard drops down. However, if I lift it up at a slight angle the keyboard remains "attached" to the screen. It seems as though there is a magnet of some kind holding it in place.
I instinctively hold it with forefingers and thumb to type much as I do on my Motorola Milestone which slides straight up and down and has no "hinge".
As for lying on my back and typing in Bed if I just hold the bottom portion keyboard along then the screen drops down. HOWEVER that is an extremely awkward way to type for anyone I would imagine.
The question is, did HTC design it to work in this way knowing that people "instinctively" do these types of actions in this way?? I am not sure they conduct such a detailed ergonomic study. There are people that have no hinge issues at all, but unless they apply specific tests as I did here it would be difficult to know if they are experiencing similar problems. If they are doing what comes naturally and holding it as nature intended then they would not deem that there are any problems.
Just my two cents.
This is worse than the "Is my trackpad wobbling?!" threads on CrackBerry. It's supposed to be loose so you can open it with one finger, according to HTC. If you don't like it, take it back (you can definitely get a refund, since it's only been out like 4 days or whatever) and get a new phone. Seriously. You want a stiff slide, get a Milestone, then you have nothing to complain about.
Bought 2 today, they're (identically!) quite loose. I was really worried before buying that I'm gonna get the 'loose one' but to be honest it's not an issue as it's a very weird way to hold your phone and like others said you instinctively hold the device with your thumb and index fingers as that's where they end up when you open the phone. Furthermore, if opened and held vertically just by the bottom, the top part stays in place and only drops down at ~40 deg angle, so unless you text a lot in bed while holding the phone upside down and holding it just by the bottom bit, you won't have a problem. If I lift it up like in the video (it's actually quite an effort) the parts will separate.
Yeah, mine is the same, but dont know why people are making such a big fuss on it, why not for example make a big fuss on the speaker quality instead?
Yeah the speaker is ****, its the one thing that is crap with this phone...
Sent from my Desire Z Beast
Did you ever think choosing a phone would be like choosing a girlfriend. At least with the Desire Z you can test it out in the shop to see if its loose before getting it home and having a nasty surprise lol XD
I never knew I had a hinge problem until I watched the videos. Some people have way to much time on their hands.
Sent from my T-Mobile G2 using XDA App
I'm pretty content with my Epic so far. I've had it since November and have had no major issues with it and any I did have I was able to fix (no gps after flash, fixed thanks to Epic community, unresponsive screen orientation, fixed thanks to epic community again).
But I'm noticing a potential problem that I'm afraid no one here will be able to fix.
One of the minor gripes I have with my Epic is that whenever I press the top right button on my phone to either lock or unlock it, I ever so slightly apply some pressure with my fingers as if I wanted to push the screen up to slide out the keyboard. The amount of pressure my fingers are giving is minuscule but I'm already noticing that my phone no longer is as firm as it was 90 days ago.
This troubles me because I hardly ever use the keyboard, in fact, I only used it several times the first month to try out some emulators but gave up on it because the keyboard just isnt that great for it. My fear is that this phone is going to get as loose as the epics you find at the Sprint stores in less than a year!
Dont get me wrong, I dont expect the sliding mechanism to be strong forever, but I am pretty surprised that the phone is already feeling loose and I dont even use the physical keyboard
My question to you all is are any of you experiencing the same problem? How about those who use the keyboard frequently? Is there any way we can "re-tighten" whatever it is that is getting loose??
My phone is only 2months old and when the keyboard is shut and you look at it from the volume side I have a huge gap there. The slider is a little loose not to bad. My problem is just the gap issue. If I press on the left side of my screen you can literally see the left side of the screen go down due to that gap. I'm gonna be exchanging it soon I just don't feel like it cause my setup is finished and I just dont feel like doing it again.
I notice the epic case set helps it from feeling as loose now.
Sent from my SPH-D700 using XDA App
musclehead84 said:
My phone is only 2months old and when the keyboard is shut and you look at it from the volume side I have a huge gap there. The slider is a little loose not to bad. My problem is just the gap issue. If I press on the left side of my screen you can literally see the left side of the screen go down due to that gap. I'm gonna be exchanging it soon I just don't feel like it cause my setup is finished and I just dont feel like doing it again.
Click to expand...
Click to collapse
You can backup your data to your pc..and when you get your new epic just throw it back in.
Sent from my SPH-D700 using XDA App
It is what it is...
There are multiple causes for the screen wobble effect, and once it gets loose, much like a fine woman's _____, there's not much you can do to fix the situation. I've read on here how people have taken their epic's apart to try and tighten the slider but it's just not possible unless you send it back to samsung to have them do it. However, there are a few solutions insofar as mitigating one's "noticing" it on a daily basis. Both the Otterbox and Seidio Active X are nice cases and once they are attached, there is not really any screen wobble effect due to the way the cases fit. Although, what most people don't realize is that most of the cheap cases that are available for the epic (including the ones at the sprint store and the non-platinum series cases at best buy) are actually to blame for creating the gap between the screen and keyboard in the first place. The way that they clip on to the phone is not very well thought out like on the more expensive cases and the clips sometimes overlap and are simply thicker than they need to be on most of the cheapo cases. I learned this the hard way with my first epic and when I figured it out it was still within the 30 day trial period Sprint gives you with their phones. So i took it back under "false pretenses" and told bestbuy that the earphone speaker quality was ****ty compared to my "friends" Epic and that i wanted to get a different Epic. I've been very careful about which cases I use on my phone from that point on. The Seidio innocase and active x, platinum series, and otterbox cases are all the ones i know for sure that won't cause a "gaping" effect on your phone. All the ones at the sprint store have a negative impact and even the otterbox does just a tad, mainly due to the side clips on the top bezel that clipon by the top row of numbers on the keyboard.
anyways, that's my 2cents
Hi everyone, I very recently purchased my brand new Desire Z. So far, I am really impressed with the software and general likability of the phone.
Although, having read too much about the Z hinge, it really makes me paranoid sometimes while handling the phone.
A few obervations and questions, which if someone with a few months of experience could respond to would put me at ease,
1. The Z hinge is surely loose, but doesn't worry me in general use. Although, I am scared it will get further loose with time, is that so?
2. The cable / ribbon running along with the hinge is not protected, is the wear and tear comparitively higher because of having no protection? Should I be budgeting in changing the ribbon every couple months?
3. Because of the hinge being loose and possiblity of the keyboard opening on a fall seems almost definite. Doesn't that put much more at stake on a fall comparitively? Fortuunately, mine hasn't fallen yet, but what's the experience you all have had with your devices falling on hard surfaces? Other than the scratches, that's not a problem. I am worried, the device will break in pieces if it falls!
4. For a little more peace of mind, are the hinges metal or plastic? I have read both on reviews and I can't seem to find a definitive answer to this one.
Thank you for taking out the time to read and respond with your experiences.
Sent from my HTC Vision
I've had mine since January and I've dropped it plenty of times. I have never had any problems with the keyboard, hinge, or ribbon cable.
After dropping my phone a few times my phone speaker went down... Had to replace them
Sent from my HTC Vision using XDA App
So it does seem like it is a sturdy device, or at least as sturdy as the other devices.
Any idea about the hinges, if its plastic or metal?
Thanks!
Sent from my HTC Vision
Fairly certain they're metal. I've dropped my caseless G2 several times but it's only dinged with no other damage.
Sent from my G2
don't know about the hinges if they are plastic or metal...
but i got it 5 months ago... dropped it plenty of times... and nothing happened... not even a scratch
these kind of phones are sturdy... unlike samsung phones (believe me, i had one)... it breaks into pieces...
———————————————
sent from a phone... 'nuf said
btw... justin bieber sucks
———————————————
don't worry about the hinge
d_gkal said:
don't worry about the hinge
Click to expand...
Click to collapse
+1, I dont get it, lot of discussion on this, but never I never had any problem with the hinge...
I know, lots of discussions on the hinge, but I guess its the placebo based on the early hands on the device. Although, I am getting much much more comfortable and relaxed about it.
In a nutshell, its a great device. Thanks everyone for endorsing it for me!
Sent from my HTC Vision
The G2/Desire-Z is one of the most rugged phones ever made, the only knock is that some people find that the hinge spring action gets loose (mine never has) - but if yours ever does, and you are comfortable taking your phone apart, you can replace the stock hinge spring in about 30 minutes, start to finish. - The part costs about $5 - Then it will be tight as hell like when new! (possibly tighter than new)
There is a great thread on this here on XDA complete with an HD video showing you an exact POV of the procedure being done in it's entirety!
The phone is quite sturdy overall. I had a stone thrown at my screen and no change whatsover.
Sent from my HTC Vision using XDA App
First half fall and its scratchless
Why I call it a half fall is, it didn't fall but it it lost my hand and hung from the charger and hit the side of the bed pretty harshly. The keyboard did open up though but luckily all's good - gave me a little more confidence on the device build.
Sent from my HTC Vision
Dropped mine a few times - the battery cover always seems to fall off when that happens. Few dents and scratches but nothing serious.
As for my opinion about build quality, personally I think it's pretty crap, due to the design of the hinge. I changed my first DZ for another, since the first one had a ridiculously loose hinge. The second one developed the same problem in 24hrs. It's not that that bothered me so much, but the fact the two halves were not held snug together by the spring, so touching or pressing on the touchscreen caused the top half of the phone to tap annoyingly on the bottom half.
Eventually I bodged this by sticking layers of electrical tape between the two halves. It's not visible in normal use, but I'm pretty annoyed that I had to do this to my (then brand new) phone. Good job nothing better with a keyboard has come out yet, cos if I tried to sell this thing then I'd get literally nothing for it.
The lacquer on my battery door started falling off after a couple of weeks. My physical camera button only works intermittently, but I won't send it away for repair because I don't know what software it will come back with - it's over a year since I rooted this thing, and I don't feel like researching the latest methods, or finding out that HTC have closed all current ways to root.
This phone does not have good build quality, in my opinion.
setspeed said:
Dropped mine a few times - the battery cover always seems to fall off when that happens. Few dents and scratches but nothing serious.
As for my opinion about build quality, personally I think it's pretty crap, due to the design of the hinge. I changed my first DZ for another, since the first one had a ridiculously loose hinge. The second one developed the same problem in 24hrs. It's not that that bothered me so much, but the fact the two halves were not held snug together by the spring, so touching or pressing on the touchscreen caused the top half of the phone to tap annoyingly on the bottom half.
Eventually I bodged this by sticking layers of electrical tape between the two halves. It's not visible in normal use, but I'm pretty annoyed that I had to do this to my (then brand new) phone. Good job nothing better with a keyboard has come out yet, cos if I tried to sell this thing then I'd get literally nothing for it.
The lacquer on my battery door started falling off after a couple of weeks. My physical camera button only works intermittently, but I won't send it away for repair because I don't know what software it will come back with - it's over a year since I rooted this thing, and I don't feel like researching the latest methods, or finding out that HTC have closed all current ways to root.
This phone does not have good build quality, in my opinion.
Click to expand...
Click to collapse
A better hinge would have surely made the phone much more sturdy. That's what has always scared me so far, but now that the phone is 2 months old now I have started to get more comfortable around it.
Milestone 3 or MyTouch Slide could be good contenders, I think.
Sent from my HTC Vision
Don't get me wrong, there is no other phone I'd rather have at this moment in time - but that's due to a lack of qwerty phones on the market, as opposed to the DZ/G2 being some sort of amazing quality :-/
The Droid 4 looks proper nice though, hopefully it'll get released worldwide. And Motorola won't lock it down like they have with every other phone they've released since the OG Droid... but the chances of that are basically zero.
setspeed said:
Don't get me wrong, there is no other phone I'd rather have at this moment in time - but that's due to a lack of qwerty phones on the market, as opposed to the DZ/G2 being some sort of amazing quality :-/
The Droid 4 looks proper nice though, hopefully it'll get released worldwide. And Motorola won't lock it down like they have with every other phone they've released since the OG Droid... but the chances of that are basically zero.
Click to expand...
Click to collapse
I totally hear you there.
So, all the current Motorola droids are locked and can't be upgraded to cm or other custom roms? Really!!
Sent from my HTC Vision
I have been VERY careless of my phone, dropped it probably close to 100 times some of them being quite bad, and the most I can see is a couple corners have SMALL little dents, often the keyboard does open when dropped but nothing happens after that... I'd be more worried if dropped WHILE open but chances are if the keyboard is open you're typing (and therefore have two hands on it) My spring is still as sturdy as when I first got it as far as I can tell.
setspeed said:
Dropped mine a few times - the battery cover always seems to fall off when that happens. Few dents and scratches but nothing serious.
As for my opinion about build quality, personally I think it's pretty crap, due to the design of the hinge. I changed my first DZ for another, since the first one had a ridiculously loose hinge. The second one developed the same problem in 24hrs. It's not that that bothered me so much, but the fact the two halves were not held snug together by the spring, so touching or pressing on the touchscreen caused the top half of the phone to tap annoyingly on the bottom half.
Eventually I bodged this by sticking layers of electrical tape between the two halves. It's not visible in normal use, but I'm pretty annoyed that I had to do this to my (then brand new) phone. Good job nothing better with a keyboard has come out yet, cos if I tried to sell this thing then I'd get literally nothing for it.
The lacquer on my battery door started falling off after a couple of weeks. My physical camera button only works intermittently, but I won't send it away for repair because I don't know what software it will come back with - it's over a year since I rooted this thing, and I don't feel like researching the latest methods, or finding out that HTC have closed all current ways to root.
This phone does not have good build quality, in my opinion.
Click to expand...
Click to collapse
Lol and that's why I got the slide, I hate the hinge with a passion. I luckily got the slide and gave the G2 to my mom. The slide has an awesome build quality dispite the not so appealing look the quality is great.
I have dropped the G2 a couple of times but it had the rubber case on so nothing happen to it. Haven't dropped my slide so I can't compare
Sent from my myTouch_4G_Slide using xda premium
I had this since summer 2011. I did get a case (stays attached to the phone) for this phone and found the hinge very weak, it will slide out if I held it in at an angle. Then recently I removed the case and there was no problems with the hinge since, able to hold it at many angles without worrying it slip out.
Having put my phone with keys.etc all in one pocket I found there are scratches on the back of the case. I have dropped my phone a few times but no problems.
Ribbon is good, the hinges I believe is metal (perhaps, alloy or some sort).
I wouldn't worry about the hinge too much unless you plan to keep using the same phone for more than 3 years. HTC does also have a global 2 year guarantee (from day of purchase).
Sent from my HTC Vision using XDA App
I switched from GNex because I couldn't stand that plastic back panel crackling and how cheap it feels (like every Samsung does). Now I have N4 and what started happening to my GNex after two weeks, the same thing started happening to my brand new N4 after 4 freakin' days!!! I am pissed beyond words! This is suppose to be Google's flagship? Seriously?! I seriously regret that I didn't take HTC One instead!
Even small pressure, like putting the phone on desk or holding in hand, will push back plate slightly into phone, thus creating gap right next to it on the right side and on bottom of the left side. When I put it to my hand to clean the display the back plate will make move again. So in the end almost every pick-up I make is "packed" with crackling sound from either back plate or sides, like if I was holding cheap Samsung crap for 1 €! I didn't pay 450 € for this disappointment!
Thanks for your opinion. Not.
This thread is going to be closed.
Terepin said:
I switched from GNex because I couldn't stand that plastic back panel crackling and how cheap it feels (like every Samsung does). Now I have N4 and what started happening to my GNex after two weeks, the same thing started happening to my brand new N4 after 4 freakin' days!!! I am pissed beyond words! This is suppose to be Google's flagship? Seriously?! I seriously regret that I didn't take HTC One instead!
Even small pressure, like putting the phone on desk or holding in hand, will push back plate slightly into phone, thus creating gap right next to it on the right side and on bottom of the left side. When I put it to my hand to clean the display the back plate will make move again. So in the end almost every pick-up I make is "packed" with crackling sound from either back plate or sides, like if I was holding cheap Samsung crap for 1 €! I didn't pay 450 € for this disappointment!
Click to expand...
Click to collapse
Its a tiny creaking noise, and from that you're saying it feels like crap? *Cough"OCD*Cough* Let the phone 'ware in'..
It's anything but tiny. I can hear it and feel how it moves by simply using it. I don't need to perform any special moves or something. A simple pick up suffice. Considering this phone has nothing removable (except SIM card), but still manage to bring the same issue, it says a lot about it's build quality.
I think it's the issue with your particular Nexus 4... mine one feels very solid. :/ maybe try to exhcnage the phone?
I used to have a GS3 but i couldnt stand its cheap materials, so the nexus 4 feels like a much needed upgrade in terms of hardware
The back panel literally bends into the phone. How is this even possible with glass back panel is beyond my comprehension.
P.S.: I was worried, like many others, that I'll scratch it somehow and somewhere, so I was keeping safe. I mean extremely safe. I didn't even imagine that this would happen regardless what I do.
I would not call the device crap if you are having problems. Its something wrong with you or that particular device, as numerous people and developers love this phone
This guy is for fail
What did you really hope to accomplish by posting this here? Your first world OCD problem does not concern any of us and in fact and this may come as a shock. Most people frequenting this forum happen to like our N4. Stop being a whiny ***** and sell it if you don't like it.
Terepin said:
It's anything but tiny. I can hear it and feel how it moves by simply using it. I don't need to perform any special moves or something. A simple pick up suffice. Considering this phone has nothing removable (except SIM card), but still manage to bring the same issue, it says a lot about it's build quality.
Click to expand...
Click to collapse
The noise most likely comes from the camera assy when the lens moves inside it. (known feature since the launch)
And the back glass indeed does flex some under pressure. Most likely thats a feature also to minimize the risk of breaking the back glass.
At least my rev11 version does flex (very)little when i press it.
Did you even test the phone anywhere before buying it?
Terepin said:
I switched from GNex because I couldn't stand that plastic back panel crackling and how cheap it feels (like every Samsung does). Now I have N4 and what started happening to my GNex after two weeks, the same thing started happening to my brand new N4 after 4 freakin' days!!! I am pissed beyond words! This is suppose to be Google's flagship? Seriously?! I seriously regret that I didn't take HTC One instead!
Even small pressure, like putting the phone on desk or holding in hand, will push back plate slightly into phone, thus creating gap right next to it on the right side and on bottom of the left side. When I put it to my hand to clean the display the back plate will make move again. So in the end almost every pick-up I make is "packed" with crackling sound from either back plate or sides, like if I was holding cheap Samsung crap for 1 €! I didn't pay 450 € for this disappointment!
Click to expand...
Click to collapse
****ing douchebag, go back to your cave of iPhones since you think that's quality, and HTC one isn't even better..just because its aluminum makes it better?? Gtfooh..and don't think you can resell it either at full price because its probably beat to **** with no screen protector like every other phone a crack head sells on craigslist
Nexus 4-CarbonROM(0100)
Tapatalk2
So get mommy and daddy to buy you another different phone.
Sent from my Nexus 4 using Tapatalk 4 Beta
So this is how it supposed to work right? Your gonna tell us, how the N4 feels like a cheap piece of crap, and if we disagree we are either A) in denial? or B) out hands aren't as finely acute as yours are and we are just too simple to realize the crappiness that is the N4 build? Thanks for this, without I would still think that the N4's build quality was actually one of the finer points of the phone.
Sent from my Nexus 4 using xda app-developers app
Thread closed. If you dont like the device sell it and get something else. Simple.