Ok so i when i go to run android from the root of my sd card and i get this little thing at the top left corner of my screen and its just gives me the htc boot screen.. can any one help me pleeease... i just wana cry because im stuck..
make sure all the files ar in a folder called "Android"
Also check what the startup.txt file says as well
should have a line saying
set cmdline "rel_path=Android"
Related
Im very confused..... there are so many files to download for the Android to work on the Vouge and i keep getting errors(i guess im using the wrong file) i follwed what was there but it's not working at all. Can someone please tell me the exact files to download?
crazylegs90 said:
Im very confused..... there are so many files to download for the Android to work on the Vouge and i keep getting errors(i guess im using the wrong file) i follwed what was there but it's not working at all. Can someone please tell me the exact files to download?
Click to expand...
Click to collapse
1. Download your desired build from vogue hero then place and rename it to system.sqsh on your SD card
2. Extract contents of basefiles from vogue-android to your sd card, along with haret.exe, and default.txt
3. These are all you should need. If you get a white screen after you run haret then you need to open default.txt and change your panel type or just download a different one from the code site with the panel type you need to change to.
Hope this helps..your phone enters a wonderful new world with Android
KERKEDAGAIN said:
1. Download your desired build from vogue hero then place and rename it to system.sqsh on your SD card
2. Extract contents of basefiles from vogue-android to your sd card, along with haret.exe, and default.txt
3. These are all you should need. If you get a white screen after you run haret then you need to open default.txt and change your panel type or just download a different one from the code site with the panel type you need to change to.
Hope this helps..your phone enters a wonderful new world with Android
Click to expand...
Click to collapse
So i followed your instructions exactly but im still having a small problem...... when my phone boots into linux i get an error: : mounting /dev/block//loop0 on/data failed: Invalid argument Failed Failed to mount /data /bin/shi can't access tty: job control turned off
ANY SUGGESTION AS TO HOW TO FIX THIS ERROR
THANX FOR YOUR ALL YOUR HELP!!!
reformat your sd card
im still getting the same error...... can ANYONE tell me exactly which files YOU download to get Android working
androids been working fine until yesterday, until i booted android and it decided to go into a disk check, or something like that and got stuck for like 3 hours so i restarted it and now every time i start android, no matter what version, ive cleaned my card 6 times and put all the stuff back in it gives me:
Code:
Failed to find system.img on SD card
/bin/sh: can't access tty: job control turned off
/
heres a picture of my folder:
Please help?
look over at the error message and the picture you posted 1 more time..i think ur system is named wrong.
im so confused isnt systemmap the ssystem.img its talking bout?
Your system file always has to be renamed to system.sqsh. (The only exception is if you have a file that is system-xxx.img. Then you'd rename it to system.img.)
Sally
it i now system.sqsh still gives me same error
Which version of basefiles are you using?
Are you using a really old version or the ones from 11/16/09?
Sally
smarcin said:
Are you using a really old version or the ones from 11/16/09?
Sally
Click to expand...
Click to collapse
i figured it out, u gotta put it in the root of the SD card i had it with the other files, but now when it boots it sits at the boot screen and doesnt actually boot up
Usually, everything goes in the Android folder, /android. It looks like you're trying to run SenseHero. Is your default.txt set at 320 x 480 with a density of 160? Are you using the hero.user.conf file from the SenseHero thread:
http://forum.xda-developers.com/attachment.php?attachmentid=259474&d=1261528033
Just replace the hero.user.conf file in your conf folder with the one I linked to.
Sally
zbubblez said:
i figured it out, u gotta put it in the root of the SD card i had it with the other files, but now when it boots it sits at the boot screen and doesnt actually boot up
Click to expand...
Click to collapse
go to andoidonhtc.com
Peace all,
Currently try to place the Andriod OS on my girlfreind's HD2. I had placed the file on her SD card before and it worked w/o any problems. Recently she started having problems so I decided to place a real "dual boot" ROM (OzDroid) onto her phone. that went well---but when i placed Meejay's Revolution 2.3 on the root of her SD card---for some reason OzDroid doesn't detect the Android build and when i try to do the fix that comes on OzDroid to repair Android it says "error on startup.txt". Can anyone help me with this or point me to the right direction?
thanks in advance
-ZDK-
Would be nice if you could post this startup.txt.
JanssoN said:
Would be nice if you could post this startup.txt.
Click to expand...
Click to collapse
It says: "error, can not modify startup.ext" when i press the button that loads Android
ZEDEK said:
It says: "error, can not modify startup.ext" when i press the button that loads Android
Click to expand...
Click to collapse
but what is the text inside startup.txt?
Perhaps it's because it's looking natively in the "Android" folder, which I know guess is not pressent on the other SD card.
Open your startup.txt on your android phone, and look for this line:
set cmd "rel_path=Android" or simmilar. If so, remove the entire cmd line, if there is nothing else in that line. Otherwise, just remove the rel_path=Android part inside the "" signs.
Hope this helps you
Stenager129 said:
Perhaps it's because it's looking natively in the "Android" folder, which I know guess is not pressent on the other SD card.
Open your startup.txt on your android phone, and look for this line:
set cmd "rel_path=Android" or simmilar. If so, remove the entire cmd line, if there is nothing else in that line. Otherwise, just remove the rel_path=Android part inside the "" signs.
Hope this helps you
Click to expand...
Click to collapse
Peace to u Stenager,
Thanks so much for ur reply....sorry I didn't get back right away---was away for holiday. However, if u don't mind...can u tell me where I go to set up the startup.txt to change cmd?...I'm totally lost.
Thanks so much for ur time & patience
-ZDK-
Sent from my HTC Evo using Tapatalk
Does It Everytime N For Some Strange Reason When I Extract The Andriod Folder To The Phone There's A Harlet File N Also A Harlet 1.5 With It
Don Boss said:
Does It Everytime N For Some Strange Reason When I Extract The Andriod Folder To The Phone There's A Harlet File N Also A Harlet 1.5 With It
Click to expand...
Click to collapse
Could you be more specific? Haret.exe is required to boot into Android. As described in the first post you need to tap clrcad.exe first (nothing appears to happen), then tap haret.exe and Android will be started. What's going wrong after you tapped those to files in that sequence?
Sincerely,
Mac
I tried to install frx 04 finished the calibration setup and then there was a black screen which i think was android booting up. However I reset my phone at this point because there was a black screen 4 about 2 mins. Tried to run haret again but got the message the file 'haret' cannot be opened. either it is not trusted..if the problem persists try reinstalling or restoring the file.
I tried deleting all the frx04 files and putting them back into memory card but I keep getting that message. What do I do ?(btw htc touch hd.)
problem solved
hard reset, changed roms, android now works!
try formating the card and reinstalling the fresh full FRX4 (dated 10/2)
ypsmav said:
try formating the card and reinstalling the fresh full FRX4 (dated 10/2)
Click to expand...
Click to collapse
yep done that nothing changed
mickeystar said:
yep done that nothing changed
Click to expand...
Click to collapse
use fresh copy of haret and see if your STARTUP.txt is right
most importantly check if this is right:
a) if your haret and other files are in root of the sd,open startup.txt and check if there is something like "rel_path=andboot" if there is,just delete that
b) if your haret and other files are in some folder eg. "FOLDER3" go to startup.txt and
-if there is no "rel_path=****" add "rel_path=FOLDER3"
-if there is just change **** to FOLDER3
be sure that rel_path has space before it and it is under quotes together
since there are only one quotes in that file,you will easily find them and place the right line there
additionally check for SD card problems,use search for your problem, you can easily find what to add to startup.txt if it is an sd card issue
farukb said:
use fresh copy of haret and see if your STARTUP.txt is right
most importantly check if this is right:
a) if your haret and other files are in root of the sd,open startup.txt and check if there is something like "rel_path=andboot" if there is,just delete that
b) if your haret and other files are in some folder eg. "FOLDER3" go to startup.txt and
-if there is no "rel_path=****" add "rel_path=FOLDER3"
-if there is just change **** to FOLDER3
be sure that rel_path has space before it and it is under quotes together
since there are only one quotes in that file,you will easily find them and place the right line there
additionally check for SD card problems,use search for your problem, you can easily find what to add to startup.txt if it is an sd card issue
Click to expand...
Click to collapse
i dont understand what u mean by ' be sure that rel_path has space before it and it is under quotes together'
i've uploaded my startup file, my haret and files are in an andboot folder with the rel_path added onto startup
mickeystar said:
i dont understand what u mean by ' be sure that rel_path has space before it and it is under quotes together'
i've uploaded my startup file, my haret and files are in an andboot folder with the rel_path added onto startup
Click to expand...
Click to collapse
Flash with another ROM, for example: WM 6.5.x (build 28244) I think it's the best!
Next.. on a FRESH formatted microSD card copy all the linux/android files except the "modules*****", "rootfs.img" and "zImage" to the root of microSD.
Go here and download the latest kernel htc-msm****
Next>> Go here and download the latest rootfs
Next>> unpack the "htc-msm***" archive and copy "modules-***" and "zImage-***" to root of microSD, rename "zImage-***" to "zImage", "modules-***" don't need rename!
Unpack the "rootfs-***" archive and copy "rootfs-***.img" to root of microSD, rename "rootfs-***.img" to "rootfs.img", delete "data.img" if exist, delete "ts-calibration" if exist!
Hope this helps!
Best Regards, FLeX!
Edit: use the untouched STARTUP.TXT
mickeystar said:
i dont understand what u mean by ' be sure that rel_path has space before it and it is under quotes together'
i've uploaded my startup file, my haret and files are in an andboot folder with the rel_path added onto startup
Click to expand...
Click to collapse
If that's your startup.txt, the problem is right there:
NOT:
....gsensor_axis=-2,-1,3"
boot
rel_path=andboot
BUT:
....gsensor_axis=-2,-1,3 rel_path=andboot"
boot
That should fix the FIRST problem with booting it up.
Another problem might be still having the USB plugged in to the phone. Be sure to take it out before running haret.
hrk7474 said:
If that's your startup.txt, the problem is right there:
NOT:
....gsensor_axis=-2,-1,3"
boot
rel_path=andboot
BUT:
....gsensor_axis=-2,-1,3 rel_path=andboot"
boot
That should fix the FIRST problem with booting it up.
Another problem might be still having the USB plugged in to the phone. Be sure to take it out before running haret.
Click to expand...
Click to collapse
changed it not sure if its right though still doesnt work, can u upload rite startup txt file for blackstone please
mickeystar said:
changed it not sure if its right though still doesnt work, can u upload rite startup txt file for blackstone please
Click to expand...
Click to collapse
Better yet. I took your startup.txt made it look more readable.
See pic for how the folder should look.
Don't worry about not having data.img and tscalibration files, they are created on first boot.
And there's a great video about it on youtube by theDeadCPU. --> VIDEO <--
Just in case your kernel doesn't ask for calibration, download the attached file and put it in andboot folder. Remove extension (should be ts-calibration)
hrk7474 said:
Better yet. I took your startup.txt made it look more readable.
See pic for how the folder should look.
Don't worry about not having data.img and tscalibration files, they are created on first boot.
And there's a great video about it on youtube by theDeadCPU. --> VIDEO <--
Click to expand...
Click to collapse
still not working, i used your startup. these are the files on my andboot folder on my storage card.
sorry about image quality had to resize
any1????????????
mickeystar said:
these are the files on my andboot folder on my storage card.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showpost.php?p=11411484&postcount=10
thanks for the replies but i think my problem goes further
http://forum.xda-developers.com/showthread.php?p=11572912&posted=1#post11572912
problem solved
hard reset, changed roms, android now works!
mickeystar said:
thanks for the replies but i think my problem goes further
http://forum.xda-developers.com/showthread.php?p=11572912&posted=1#post11572912
problem solved
hard reset, changed roms, android now works!
Click to expand...
Click to collapse
Glad it works now.