Charger Plug Fitness - XPERIA X10 General

just a quick question guys
when you plug your charger into ur X10, is the plug slightly lose?
mine wiggles a bit and *i think* when it was new, it was tight
maybe im just imagining things, i just wanted to check with everyone

Mine wiggles a bit ever since it was brand new.

Mine got loose too.. Just bend the connector out a bit (the side without the pins) you can use a fingernail
or just buy a new cable

And after wiggling, it is broken...

Related

Any hope in repairing pin on battery clip?

I'm not sure if my title makes any sense, so I will further explain here. I had to repair my charging port, while doing so I must have damaged the clip that the battery plugs into. It looks like a pin or two (that is soldered to the mobo) is a bit loose. My phone does not charge but will function when plugged in. I bought a replacement battery thinking I damaged that, when going to install I noticed the loose pins. Went through with the install anyway, and phone acts the same.
Is there any hope for my to resolder the pins back to the mobo? I want to get some input before I buy a soldering gun etc.
A1will said:
I'm not sure if my title makes any sense, so I will further explain here. I had to repair my charging port, while doing so I must have damaged the clip that the battery plugs into. It looks like a pin or two (that is soldered to the mobo) is a bit loose. My phone does not charge but will function when plugged in. I bought a replacement battery thinking I damaged that, when going to install I noticed the loose pins. Went through with the install anyway, and phone acts the same.
Is there any hope for my to resolder the pins back to the mobo? I want to get some input before I buy a soldering gun etc.
Click to expand...
Click to collapse
Resoldering battery connectors is normally a very difficult job, best to take it to someone experienced. If the solder pad is gone too you'll definitely need a professional.
DrFredPhD said:
Resoldering battery connectors is normally a very difficult job, best to take it to someone experienced. If the solder pad is gone too you'll definitely need a professional.
Click to expand...
Click to collapse
What makes it so difficult?
Or by me asking do I show that I'm in over my head? lol

New way for magnetic charging port to break

Typically the issue on our phones is that the magnetic port pulls out after a lot of use. I had this and I superglued that sucker back in. Now, I have a whole new issue. One of the little nubs with the metal contact completely came off! I seriously have no idea how they could have happened. It's hard to describe but I'll take a picture when I can to show this. The annoying thing is that I superglued this one in very well. I would have to seriously risk breaking more things to pry this one off to replace it! Despite no update to marshmallow (D6616) and these crazy build issues I still don't see a compelling new phone to replace this one -_-.
Pics. Initially, the little metal circle was gone. I scraped away the rest of the little black circle to expose the little bit of metal that is still sticking out. I can still use the magnetic charging port as long as I carefully attach it in a way that the little metal piece makes contact with the charger.
Please make a photo of your magnetic cable connector too
When the microphone of my z3 broke, the service changed all the frame of my mobile.
i was so happy, my old magnetic charging port was very worn out (almost like your picture)
I blame users using cheap magnetic cables bought from ebay and amazon because of this. Magnets can be super strong, strong, medium, and weak. Mine has been fine since owning the phone Dec 2014. I use the Sony magnetic dock and always charge on it. The only problem I have is that it needs a backbone to charge because DUE TO MY FAULT, when the phone dropped, it bent the trim area of the magnetic port.
People always need to point fingers at everyone besides themselves.
lvlonkey said:
Pics. Initially, the little metal circle was gone. I scraped away the rest of the little black circle to expose the little bit of metal that is still sticking out. I can still use the magnetic charging port as long as I carefully attach it in a way that the little metal piece makes contact with the charger.
Click to expand...
Click to collapse
By the condition of your phone from the pics you posted I'm not surprised. I have 2 magnetic chargers and non have this issue. The magnets are relatively weak - just strong enough to hold the cable to th phone while moving it around - and I've not experienced any issues although my charging port doesn't look near as haggard as the ops.
Sent from my D6603 using Tapatalk
I use the magnector connector which is what initially caused my magnetic port to pull out. My magnetic port looks all jacked up because I superglued the port back in but got messy with the glue and had to scrape some off. Anyways despite how messed up my magnetic port looks, the rest of my phone is actually pretty much in new condition. I have had it in a case all its life and a glass screen protector.

Could I improve water resistance with magnetic connector and caulking?

Recently my phone was damaged through the charging port due to moisture. In the morning I typically bring my phone with me to keep track of time. Usually I would blow out the port to remove water but when I plugged in my charging cable later in the day, the connector got so hot it burned the tip of my fingers and melted some of its internal plastic into the port. So now I can only charge wirelessly. I'm thinking what if I purchase a magnetic connector and leave it there permanently and seal the gap with some metal purpose caulking. In the case I get moisture on the contacts I can just wipe it off.
Immediately I want to say it's a very bad idea, mainly because most caulking has an off-gassing effect that could be damaging to the sensitive innards of a phone. But! I'm surely willing to be impressed. Be leery not to get any on the actual contacts and use it sparingly, you may be OK.
Batryoperatedboy said:
Immediately I want to say it's a very bad idea, mainly because most caulking has an off-gassing effect that could be damaging to the sensitive innards of a phone. But! I'm surely willing to be impressed. Be leery not to get any on the actual contacts and use it sparingly, you may be OK.
Click to expand...
Click to collapse
When I get my phone back I'll post some pictures.

How hard is it to destroy the V20's Type-C connector phsically?

How much force would I need to exert for the connector to break? I'm asking this because I've heard that the connector isn't replaceable without replacing the entire motherboard, and I'm a bit paranoid about it breaking:silly:. Thanks in advance!
p7810456 said:
How much force would I need to exert for the connector to break? I'm asking this because I've heard that the connector isn't replaceable without replacing the entire motherboard, and I'm a bit paranoid about it breaking:silly:. Thanks in advance!
Click to expand...
Click to collapse
Owned g3, g4 and now v20. Totally normal to ask about this. Even if you protect your phones with cases and tempered glasses, two primary weak spots remain: motherboard battery contacts wearing out and breaking off (happened to me on my G4) and USB-C troubles. As both the battery connector and the USB-C port are soldered onto the motherboard, even if your phone is under warranty, the only fix is installing a new motherboard, losing the data (back up your data often!) As I was explained in the service center, taking the parts off the motherboard and soldering the new ones back on (that's only if you have a donor motherboard or parts to begin with) results in heating the surrounding circuitry area to the temps of up to 400c, risking damaging the metal tracks (or ripping the seating metal pucks for the parts off the board altogether on removal).
Since the g4 mishap, my solution for effectively protecting the USB port from wear, pulling and yanking damage is the permanent (but easily removable) magnetic USB-C insert that lives in your phone all the time and has magnetic studs on the outside plane that the charging cord snaps to. There are several manufacturers of those on Amazon, none are perfect but any of them is better than using your port "raw" daily. WZKEN makes tangle-free USB-C cords with strong contact between the insert and the cord. The cords (at least in my case) support Qualcomm quick charge 2. When connected through a WZKEN cord, my Anker QC2 charger plug changes light from blue to green to indicate QC and my phone notifies me QC is on, so the QC handshake works as expected.
One thing though if you go the magnetic rout - order MORE inserts than cords, if your USB-C port is loose, the inserts might fall out every once in a while, you'll lose them. Also I haven't seen any magnetic cords with light indicators that change color when QC kicks in, all the light shows is that there's electricity in the port on the wall charger that your cord is connected to. Also, WZKEN cord heads snap to the inserts the right side up only, not on either side.
Whatever the quirks, beats the every day pounding that USB-C ports take by far, especially knowing v20 doesn't charge wirelessly! Inserts are small enough to fit into all port cutouts on all cases I have, so no problem there, either.
The solution is so simple that I charge most of the micro-USB and USB-C devices in my house this way.
p7810456 said:
How much force would I need to exert for the connector to break? I'm asking this because I've heard that the connector isn't replaceable without replacing the entire motherboard, and I'm a bit paranoid about it breaking:silly:. Thanks in advance!
Click to expand...
Click to collapse
Very very hard.
Sent from my LG V20 using XDA Labs

Note 4 charger port housing bent - charger cables keep snapping

Hi there.
A few months ago I dropped my refurbed, less than 2 month old, N4 on a chair leg and the housing around the charger port broke. I was told the motherboard was screwed, hence why the charge wasn't lasting. I decided the phone was too good to get rid of so I kept with it. The other day the official charger lead cable charger USB plug snapped. I put it down to being squashed by a chair. However, another cable did the exact same thing (and wasn't squashed by a chair). Could it be as a result of going into this bent housing? What is the solution.
Thanks
A bit difficult to ascertain what's actually going on without something to look at.. Would you mind posting a few pics of the housing around the charging port and the snapped cables.
On a lighter note, Looks like your N4 doesn't quite like being around furniture (chairs, specifically )

Categories

Resources