Database Users

XDA2 fell in water Please help!!!!

i ve a xda2 it fell in water and after that i got it dried n cleansed from a dealer but now the problem is that it only works upto the "align screen" intial setup and downt move any further i also tried to ugrade with WM5 bt same thing, Please help me. I shall be thankfull to all to you.
Kindly help

Hi,
try to clean board with isopropyl alcohol or in ultrasonic cleaner. Maybe it can help you.
jsec

Is it really dry? It can take some time...
See this:
http://forum.xda-developers.com/viewtopic.php?t=22275&highlight=
Andre

Replace the battery
I had the same problem after my mda ii went through the washing machine. Replacing the battery fixed the problem.

thanks guys for the replies , further my XDA had been properly dried and cleaned but now the problem is that the machine doesnt operate further than the "ALIGN SCREEN" setup where one has to tap the screen at four corners and the center one I tap the screen i return to the same screen as ask to tap the screen again.
Will flashing the rom serve any purpose or is it aa hardware problem, rest of the device seem to be ok even the bluetooth light flashes when i turn the XDA ok. But not able to get i any further from there.
So what do the experts have to say, Please reply.
thanks again

well, mine had very hot coffee poured all over it.
my suggestion to you would be, dont turn it on or place the battery for at least 3 days if under normal drying conditions only.
or if you know how to take it apart, spray everything with contact cleaner, it will dry up immediately,
then cross your fingers and hope nothing shorted out when it first went inot the water.
strategy is - wait - dry- wait - test - dry some more - spray contact cleaner - dry - test - until such time it works. coz some moisture might still be present and causing a little bit of short circuit.

It sounds more of a hardware issue than a software issue and you may have to take is apart to fix it.
Try two things, Number 1: (You need to use some latex or vinyl gloves if you need to take your unit apart). You are going to need to check your digitizer connection to the motherbaord, make sure you don't have any mosture trapped in the ribbon lock and make sure the entire front part of the digitizer is flush against the inside case edge. Number 2: Have you seperated the digitizer from the LCD yet? If this thing was in water the slightest spot of moisture will disrupt the very small electrical field between the digitizer and the LCD that recognizes the stylus taps. Abosolutly nothing should be present between the two and also around the white or grey strip on the inside of the digitizer for it is also a contact strip. You can use a lens cleaning cloth to clean any dust and moisture from the inside of the digitizer before you put it back together with the LCD. Being I worked on about 150 toshiba e750's that suffered sprinker damage in a fire, I learned quite bit on what makes a Pocket PC tick. Good luck with getting it working.

the same
I had the same problem 3 or 4 years ago with a HP Jornada 680 (handledPC). I must unfortunately say that I could never get my touchscreen working back again. Perhaps if you could change your screen for a new one, or at least one that always worked (some are sold around the www, even a few by members here if i remember).
Good luck

Shane
the stylus is working as the sceen responds to the tabs, but the process of calibarating the screen doesnt finish and keeps on repeating. and it asks to align the screen again.
The digitiser is working but the software doesnt seem to be working...
what do you have to say?
and thanks for the reply

guys thanks for the reply
but no luck... is there any sofware that can check if the components are working and ok, or simply what should i do. The info about the problem in a nut shell is
First the loading happpens with the O2 screen then the "Windows mobile screen says Tap the screen to setup the pocket pc" Then when i tap the screen next screen comes saying "ALIGN SCREEN" with a crosshair in the middle of the screen when i tap it with the stylus it moves till all four corners are tapped which crosshair point to. But now the problem begins.
The same screen repeats and asks for the same procedure again and again and again And the Xda processing doesnt move further.
i even flashed the ROM but same thing........
no luck
HELLLLLLLLLLLPPPPPPPP!!!!!!

REPLACE THE BATTERY
Have you bought a new battery yet?
Like I said above, my MDAII went through the wash. Just like you, i got the align screen process followed by a spontaneous hard reset. I bought a new battery, charged it up in the cradle overnight, then popped it into my machine. Good as new.
Don't mess with the software until you try a brand new battery.
Cheap and effective.

Hmm, the touch screen is responding to taps, but maybe its a bit 'offset'.. I mean maybe when you tap exactly center, it will receive your tap to be a lot more offset to right, left, up or, down.. Cos that's what making the 'align screen' asks you to realign again and again..

Hi Tanvir,
I want some of the others to advise on what I am suggeting. On my xda I ( which I own as well as a Blue Angel) we are able to put it into boot mode and press the "action" or was it the "contact" button to get it into test mode. Being I don't own a Himalaya but I would guess that they would have that function too, and in that function it has a test for the aligment screen which it might be able to align in the test mode away from the OS running. If someone has the tip for helping Tanvir of getting his unit in to test mode, Please someone post it for him. Also being I don't own the XDA 2 if anyone has anything to add on my suggestions, the floor is open. let me know how it's going Tanvir. Cheers.
Shane

I'm sure Tanvir's digitizer is no more...
Go to www.ppctechs.com and purchase a new one... not that expensive!
Good luck!
Rayan

Hi shane,
thanks for the help and time i ll try the process u suggested and lets see what happens, i ll inform you if any luck,
An thanks to all the guys for helping,
Thanks
Tanvir

hi jamil
ive guessed that posibility too, but the question is there is no way to fid out if it s he reason...
thanks
tanvir

Help! Stuck on Align Screen!

Guys, I hope you can help me!
I was using my Imate Jasjar when it was accidentally bumped by another person. the Jasjar fell but it wasn't that high and the floor was carpetted. However, I noticed that whenever i try to tap on the Start button on landscape mode, the calendar application opens up! And when I try to tap V-Bar on the other corner opposite the Start button, the Contacts application opens up. Basically, the soft keys on the bottom screen are the one opening up even if I'm tapping the ones on top! If I tap the bottom soft keys, I thought the Start button or my V-bar would come out but still the Calendar and Contacts applications were the ones that opened. Basically the everything on top cannot be tapped!
On Portrait mode, I can tap the start button but when the V-Bar was tapped it still opens the Contacts application.
I went to Settings then Screen to re-align the screen. I thought it would solve the problem but apparently it didn't! I was trapped in the Align Screen section giving me an endless loop to tap the 5 areas of the screen.
I now did a Hard Reset, and now I'm forever got stucked to the Align Screen part.
What am I supposed to do??? Please help!!!

Hi,
Seen the same problem... Try to guess the error margin of the alignment...
for example instead of tapping in the center of the cross try tapping on left or right... Since your screen isn't aligned you can't press on the center...
Now the problem is hardware, not the MB but the LCD...
After tou figure out the margin error, the Universal will resume and then you ca align the screen via Start->Settings->System, align screen
I'll try to know more about this problem asking my friend.
Best of luck

thanks for your reply!
i also believe that it has something to do with the LCD. there are no cracks whatsoever. problem with the aligning is i have to keep on guessing. and if ever i do align the screen successfully, i'm not sure if re-aligning the screen in Settings would solve the problem.
i would appreciate though if your friend or anybody else can shed light to a solution.

This is a simple problem to solve ;-)
When the allign screen is ON and you have to make the first tap on the crosshair (just before you start clicking away to allign your screen), twist your display from landscape to portrait mode...
Now continue to allign it as usual, and you should finish successfully!
Cheers,
San

unfortunately, after following your instructions, i still went on an endless loop on aligning the screen. i'll try to reflash the rom and see if it would work. i hope it does...

i updated my ROM. still stuck on the alignment screen!
any more ideas?

To be honest, sounds like your screen is broke. Even if you got it to align, I doubt it would be very usable. I think you are looking at repair - if there's no visible sign of damage, you might get away with a warranty repair.
Cheers,
Steve.

Hi
Few months back i've got exactly the same problems (odd LCD behavior, impossible alignment, etc...) with an HP4700. I went to the service center and they had to replace the LCD screen. They did not charge me and take it under warranty. In my case the unit did not drop and i made it clear to them. I would suggest you go back to the service center and forget about the drop in your problem description .
Cheers,
Bruno

I had the same thing happen on a HP 3700, I did not even drop it all i did was install the Quake game for it and after a few days the screen alignment went a bit out. It was usable but definately out by about 1 cm in each direction. The unit had not been dropped. I went into the allign screen utillity and ended up in the infinite loop. The only way to fix was a new screen. But unforunately it was no longer under warranty. The screen consists of 2 separate parts the lcd and the touch screen bit. In my case the lcd had no issues just the touch screen. Very annoying but there you go.
Search your soul and do what you feel comfortable with.
Good luck
Charlie

thanks for all your replies!
i've made several searches yesterday with similar problems (even if they're using different PPC models) and they all ended up sending back their units for repair. there's even one who posted in expansys with the same exact problem!
we'll be sending it back through expansys (we got the unit from them) and hopefully get it back before the end of the month. and yes, i won't tell them that it was dropped, he he :twisted: and they won't find evidence either on the outside because there are no physical damages. what a start of the new year for me <sigh>
right now i'm back using my XDA IIi.
thanks for all your support! this is my first thread/topic in this site and it's so unfortunate that it had to be sort of a negative one. looking forward to be active more here!

Hello there
This might help (I am currently wrking with 200 PDAs so have had this a few times)
THere may be a iece of dust/biscuit crumb etc, under the edge of the casing above the screen, try using a post it note or paper and go around the casing/edge of screen, this should clear the screen of anything that may be causing this problem.
THis worked for me on the majority of non-aligning screens
HTH
DB

My story was, one day when I needed to twist the screen, it was a bit stuck so I twisted a bit harder, yes it went back. Then few days later, the mis-alignment started and since then I have been keeping to do re-alignment my screen.
My screen is mis-aligned once every 2 or 3 days or even few minutes then I have to re-align by using WM5's alignment program. It sometimes takes me 2 or 3 times or even one time.
The most anoying thing is it keeps forget after aligned screen.
Now, certainty, I don't think it is a screen problem because after running alignment app, it correctly pointed into the right spot but then it forgot where the right position was.
I have done the upgraded ROM ( even tried Ivan AKU 3.2 ROM ) but problem still persisted.
I just tried clean up the edge of screen, finger cross, hope it fixes my problem.
Bad thing is, I bought my device from UK and I am living in Australia so therefore, my warranty is definately invalid. I don't want to spend 200 AUD for the new screen ( unless I am 100% sure that LCD is faulty ).
Anyone has any idea or even a better suggestion because I don't see many people having this problem.
I suspects that maybe the flex cable got ripped but not totally ripped. Don't know , please help me out on this one
Best regards

Anyone has any idea about my problem ??
One question :
I know that the flex cable has 2 connectors ( one is for LCD display and another is for LCD function ). Now does LCD function relate to the touch screen function ? and if one tiny wire of the function cable got cracked, but not totally cracked, will it affect the touch screen function ?
Other thing, does WM5 store any setting relating to screen alignment setting ? If yes, where is it ?
Thanks

Hi, from another forum, it only help to bypass the alignement loop:
"here you go theses are simple steps to bypass the touchscreen alignment.
Install you activesyn blah blah blah when it finds it go on my computer and go into your PDA device
go to windows startup and delete the Welcome file
after that give your PPC a soft reset and BAM u by passed the screen now get a free desktop program liek pocket controller from the internet it will automatically install on your pda and BAM you can control your pda add music and whatever
but now if you want to click stuff on the road get pen irazu just search on google and send it to your PDA then go to file explorer and double click it and you got a cute little mouse program that you can use like a stylus"
also try this little soft:
http://www.codefactory.es/downloads/mobile_speak_pocket/release/MSP_RemoteAlignment.zip
Hope it helps.
MaX

Hi godtakeit!
I've had the same problem a few weeks ago (and still having it from time to time) and for me a slight (very careful) bending of the screen makes it work again. It seems to me that there are connector behind or near the display which has some loose contacts.
Did you notice any other problems which came in conjuction with the alignment problem (e.g. speaker not working)?
.ox

Hi oxident
No, I don't have problem with speaker ( it was not working before but it is because of the jack plug problem - it solved ). Yeah, I did notice if I bend the screen carefully, the problem is gone. The funny thing is when I aligned the screen, it worked but if I closed it off and left it over night, it started again when I opened the lid.
You may right about the connector between LCD screen and mainboard. Well, I have no choice but openning the device and check it up.
Also, I read the thread somewhere in this forum and somebody advised this problem maybe relates to magnet around device. My brother aslo advised me that LCD charged and reserved negative electrons. Wierd but I am experiment it at the moment ( taking off battery and leave the device for a few days so that it can release the negative electrons ).
Hope it fixes

please help
i have an imate jas jam that i i got from my father he used it for like 3 years and it is pretty banged up so i cant use the warranty and repairs cost a lot, any who i got it yesterday and it was very slow so i reset the settings and now im stuck on the align screen it keeps going on for ever and ever if any one knows any thing plzzzz help

Welcome aboard
You have one of the best HTC devices ever made!
Have a look here to locate the solution to your prob:
http://forum.xda-developers.com/showthread.php?t=549207
Post number 2
Good luck,

Screen Alignment Experiment Mystery

Try this:
1. Wait till the screen misaligns
2. Switch off device
3. Use a clean cloth and apply pressure EVENLY on the WHOLE of the screen (as if 'ironing' the screen)
4. Power on the device
My XDA Trion (HT626) re-aligns itself WITHOUT having to go through the screen alignment 'routine'.
How about yours?

hellogts said:
Try this:
1. Wait till the screen misaligns
2. Switch off device
3. Use a clean cloth and apply pressure EVENLY on the WHOLE of the screen (as if 'ironing' the screen)
4. Power on the device
My XDA Trion (HT626) re-aligns itself WITHOUT having to go through the screen alignment 'routine'.
How about yours?
Click to expand...
Click to collapse
And how long you have to re-do again ? Or only one time for yours then no more misalignment?

hellogts said:
Try this:
1. Wait till the screen misaligns
2. Switch off device
3. Use a clean cloth and apply pressure EVENLY on the WHOLE of the screen (as if 'ironing' the screen)
4. Power on the device
My XDA Trion (HT626) re-aligns itself WITHOUT having to go through the screen alignment 'routine'.
How about yours?
Click to expand...
Click to collapse
And how long you have to re-do again ? Or only one time for yours then no more misalignment?

Re
I don't know, here are my thoughts.
I am 99% sure that screen pressure will affect alignment - when I had misalignment, i used the stylus to press the screen in different areas, the contact point position will change in response to this, though i have no idea where it will change to.
So even if my method does have some effect, eventually the screen layer will 'loosen' again and you will have to 'press it back'.
The 'loosening' of the screen layer may be due to vibration, heat (from battery?), deficient screen etc.

a question a bit OT: how much time after the first start your TyTN had the mis-alignment of the screen? you found it also in the very first days of use?

whassup people
had the same problem..got the tynt yesterday..today have scrreen alignment issues..tried what u told me n works..
hopefully it will keep working
thanks

works for me too
I have had an m3100 for a month now and no screen problems until last week. getting more and more frequent now. 4 or 5 times a day at the moment.
sometimes just opening the keyboard and closing it again sorts it. sometimes just pushing the screen gently here or there sorts it. if I power off and run my finger around the perimeter of the screen that always sorts it out!
I have a screen protector fitted. is this a factor?
I think it maybe due to pressure on the casing when its in my pocket sending the screen out. I've never used the magnetic case and I've not tried the screw adjustment thing yet.
my problem is, is that i've flashed the rom so I not going to be able to send this back easily for exchange even though I have orange care.

daddyo said:
works for me too
I have had an m3100 for a month now and no screen problems until last week. getting more and more frequent now. 4 or 5 times a day at the moment.
sometimes just opening the keyboard and closing it again sorts it. sometimes just pushing the screen gently here or there sorts it. if I power off and run my finger around the perimeter of the screen that always sorts it out!
I have a screen protector fitted. is this a factor?
I think it maybe due to pressure on the casing when its in my pocket sending the screen out. I've never used the magnetic case and I've not tried the screw adjustment thing yet.
my problem is, is that i've flashed the rom so I not going to be able to send this back easily for exchange even though I have orange care.
Click to expand...
Click to collapse
a most probable hardware issue, i have my lcd replaced and everything went pretty okay

I think.... HTC produces device while they're drunk... How was it possible? I'm a developer and after I finished to develop a software "I MUST" test it because if something doesn't work my boss become a T-Rex, and "I WANT" test it because in my opinion custom satisfaction is much more important then moneies.
Sorry for my poor english, I'm lerning it.
I am a disappointed XDA Trion owner.

Anyone with this problem try this out:
Open up the keyboard and flip the device over so you are looking at the back.
You will see two screws at the top of the screen on the rear. Losen them off a bit and retighten, but so that they are NOT AS TIGHT as they originall were.
See how you go.
I saw this mentioned here...apparently it can fix the problem for good. The issue is that the screws were overtightened at the factory and there is also a seal that runs out the edge of the screen. As the device gets used/warm the seal expands a bit causing pressure to be applied. If the screws are over tight then this impacts on the touchscreen causing the misalignment.
Try it...might fix it...

Screen Alignment Problem Fixed 100% Working (WithOut Voiding ur Warranty!!!!)

Hello There everybody....
I have been using htc tytn sn ht628 from the begining of the september and the sa probs started to occure after 2 week or so....it generelly occure when the device got hot due to recharge or using for some time and also when i try to clean the screen with a soft cloth....so i tried all the methods discribed here like flashing particular rom or keeping 20 mb free on phone!!! or loosing the two screw on the back of keyboard...but nothing helped me...the sa probs do get back again and again due to hotness or pressure on screen when cleaning the screen....
then i tried the business card method.....and removed the fomes that was glued with the screen and casing....but alas it lasted for some hours only....i have to do the same thing again and again...so finally i got frustated and sold my tytn to one of my friend...(i could not go for warrenty easily as i brought it from usa and i live in south asia..) and then i brought a dopod 828pro with serial sn ht639 3 weeks ago when i was returning from malaysia after a business visit....
but the sa probs get back to that new device too!!!!!!!!!!!!!!!!!! just after 2 days...but i have left malaysia within that time so i am unable to claim for warrenty now....
from my frustation i had been almost decided to open the set completely and use the method described in two japanise site where they mentioned to remove the foam and use some small sized foam...but that also instied me as it will void the warrenty and im not that of expert on opening set so anything might happen...
so finally i decided to apply my own method (actually not my own method but the combination of all the existing method...) and walla... i got wonderfull success now i have two perfectly working hermes (tytn and dopod 838pro) which where used to have sa probs....now they dont show any sa probs even due to excessive hotness of 3-4 hour use and charging not even for hard pressure on screen due to cleaning or so...i am using both set extencievely (one me and one my friend) for more then 13 days now after fixing it and they are working like angel.....i was thinking to share the methods here as you all helped me on many things over long time...i waited those ten days to make sure everythings working ok and sa probs dont came back....and for 100% confarmation....
now here goes the steps that i used to fix the two set.....
1)open the two (2) small screw located on the back of the keyboard...
2)Use a hard and sharp business card (i used prepaid scratch card i got when i do refill my mobile) to clean the foam and loose the screen from the casing...you will see a noticiable empty space between screen and casing if all the foam is clean....you will be needed to do this step a number of time to make sure everything is clean...you actually need to do this thing in both side of the screen (left and right)
3)Now the actual thing that i used from my own thoughts...i cut two piece of that business card i used in step two (in my case the prepaid plastic scratch card which is thin and hard ) and pushed them in the empty space of both side of the screen (left-right) that been created in step two....the size of the piece is small enough to get inside of the hole and hide its presence when you look straight to the screen you can only see its pressence when you will look from one side....also make sure the length is not two long mine size is like 10/1 size of the whole screen length and the wideness it also importent make sure to push it as far as it go to the end of the casing..so that its presence is unoticed...also make sure the tickness is not two much so that the screen and casong doesnt get two much presure....
4)now put those two screw again you can tight it up but dont tight too much...
This two piece stoped the screen from getting in touch of the casing body and as a result the sa probs is gone permenantly for good....i can assure you that this will work 10000% for sure i tested it in both of the hermes verient....
now if you got any more question then you can ask me or if you like me two take a picture of the procedure or the plastic piece i used then i will post it here...
Thanks
BR.
Sajib

I'd say: Show me the pictures ...
I've got a Vario 2 HTC635 and only had SA problem after i cleaned the screen to apply the screenprotector. After a reset/reallignment the problem was gone since so I think you're right about pressure to the screen.
Also i've done the business card trick just to be sure it wont happen in future.

I wonder how this does not void your warranty?
Just for opening up the device does that (tho no-one can tell if you had done it), but surely, if you remove foam or anything else from the phone.
I'd think that any kind of modification to the phone, will catch the eye of service guys and after they have done the repair, they will send a bill.
On the other hand, if the phone works without any issues during the warranty time with that modification, hell with the warranty.

picture please.

Well, you don't need to remove any of the tamper tags with this method so unless the device gets close scrutiny beyond that, the chances are that it'll go under the radar, especially if you remove the shims prior to sending it back.

If I understand this procedure correctly this is what you're saying.
1. Remove the screws.
2. Take a thin rigid card-like material and push it between the cover and screen on both the left and right sides of the Hermes screen (when held upright) to dislodge the adhesive.
3. Afterward, wedge a screen length piece of the thin card-like material between the screen and cover on both the left and right sides of the screen to prevent the screen from touching the case in the future causing the SA problem to come back.
If I have this correct I may try it this afternoon.

some pictures would be nice
what is the length of the card pieces that you placed between the screen and the body before tightening the screw? was it one tenth of the length of the screen?
as I said please post some pictures, it would help
Thanks

yes the length is like 1 tenth of the screen size...i will post a picture of the plastic lateron that i used...

I've had serious SA issues, I just tried this.
Of course, I also lost one of the screws *grrr*
I'll let you know how it works, though!
edit: found the screw on the floor with the help of the tytn's camera LED .

Sounds true...
Actually I had the screen alignment issue and after applying a screen protection and therefore "pushing a bit" the display it is gone (hold thumbs)

Just thought I'd report that my screen has been fine (after doing this) for the past 24 hrs, a new record .

hey pkx glad to hear that my hack worked for you...im now on 15th day and im not having even a slight screen mis allignment after the hack even giving hard pressure on right side of the screen is not making any misallighment...so its now safe to say that god freed me from the sa problem curse....
sajib

I woke up this morning and my screen was misaligned .
So it's not a permanent problem for me, but it helped considerably.

1) what do you use to loosen the screws? mine looks like a 6-pointed star
2) pictures!

The screws in mine are Phillip yours are Torx based on your description. My guess would be a size thats between T-4 and T-6. I haven't done it yet so no pics.

ah torx! i knew it! i thought you only use torx on screws with messed up heads.
now where to get that screw

please,send me the pictures...
Vamp

vampirello said:
please,send me the pictures...
Vamp
Click to expand...
Click to collapse
ok i am going to post a picture tomorroaw as my camera is not at my hand right now..
and to clearify one thing more u need to use a bit of fatty card to resist the screen to get in touch of the casing..mine is like 2 time thick then of the thickness of a standard sim card...i thing it will help..
sajib

Sajib: thanx a lot for trying to help us with this annoying problem. I removed the two screws that appear under the screen when I slide out the keyboard. But I couldn´t loose the screen from the casing since apparently there are two more screws hidden between the keyboard and the screen. I don´t understand how you did it. Can you please explain me with more details???? I am aligning the screen at least 6 times a day!!! Thanx!

I need some help..
If i understand correct, just relax the screws, put the plastic to the both sides (left and right) between the screen and the front panel(WITHOUT disassembling the whole case) and then tight the screws back to the original state.Is that correct?
Also i deleted some files to get more than 10mb free space and that helped me alot
But when i clean the screen there is small change in the screen position so i still may need to do the hax.
Thansks in advice and sry for my bad english

FIX for HTC HD2 touch screen not responding

After reading several posts to find a cure for my HTC HD2 unresponsive touch screen,( Slider wont slide to open applications), I decided to verify a theory. Software... Digitalizer screen, or power button.
Ok, first I Instelled about six different android versions, and the screen slide still failed. I reverted the cell back to original t-mobile windows software, and still locked screen.
Conclussion: The sofware is not the problem.
After several attempts pressing the red power button, I got the slider to open. Briefly, it locked again. Pressed the red button hard and tried to work the slide on the touch screen. Again briefly worked. After several more attempts I got it to slide and while the phone was awake, everything worked perfect. I played games, oppened applications, texted, made phone calls, and the touch screen worked flawless.
Conclussion: The digitalizer (Thin top glass screen on top of the display that responds to touch) is not the problem.
This led me to belibe that the power button was at fault. I called T-mobile and after explaining the problem, they decided to send me a different type of windows cell. I want my htc. So I declined the offer and decided to void the warranty and take matters in my own hands. Yes, I opened my HTC HD2. This is what I found: After about an hour I had carefully taken my htc apart without braking or scratching the phone or screen. When I finaly got to the buttons on the bottom, I noticed how cheap they where made. A thin copper circle on top of two contacts held in place by tape. Yes you heard right, tape. After a while, beating on the red end key for maybe a year or two, the tape brakes and the metal piece slides to the side, and makes the button to malfunction, that's why the hard pressing to make it work. I tried A bottle of comppressed power air to clean them before disassembling the phone but the way they are installed It's not possible to clean them like that.
Conclussion: The red end key is faulty.
I decided to keep the cell alive so I went on e-bay and ordered the buttons, and just in case I also got a new digitalizer for testing purpose.
The buttons panel was about 4 dollars and some change, and the digitalizer (touch screen) was about 14 dollars for a total of less than 20 bucks. (Worth it)
So here are some pics of my cell buttons, and what it should look like. After I get the parts and assemble it I will conclude and let you know the final and official veredict. As of now, it all leads to the button.

Please do let us know how you got on. I have a HD2 which I'd like to get up and running again so I can play with custom roms and leave my other mobile alone...lol. Any chance you could link to the places you got parts/tape from, and what tools we would need?
Cheers! :good:

Did it worked ??? i am also in the same situation...please share the details,

bijeeshvs said:
Did it worked ??? i am also in the same situation...please share the details,
Click to expand...
Click to collapse
+1

listening in as well

sheesh! my wife's HD2 also stop responding yesterday, seems like clockwork that a lot are having the same problem
first have to find "how to open your HD2" w/o breaking anything in the process :silly:

Damn. The second time I'm hearing about the red button giving problems.... Will be waiting results from you dude!!! +1

still wayting for the parts
Well, I am still wayting for the parts, they are on the way. The parts I found on E-bay. The buttons panel was about five or 6 dollars, I also got the digitalizer which was about 15 dollars. As soon as I get the parts, I will assemble my hd2 with the original digytalizer (the thin top screen) and test to make sure the buttons were the problem. If all goes well, I will post a complete test result with links to how to get the parts, a link on how to dissassemble the hd2 and all info I can to help on this issue. I did a step back in life, and pulled out my trusty 7 years old motorola razr v3 and stuck my sim card so i can talk and text 5 words in 7 minutes. No internet... I need my HD2... Well, I will report back as soon as I can. Thanks for the wait...

@dragonsuicida
will be waiting for your findings & ways to dis-assemble the HD2 :fingers-crossed:

You were lucky to find the buttons' panel for 4bucks. I just checked out Ebay india, and the panel is 40bucks!!! What a robbery!

Wow. Me too!
I have been running Win6.5 still on my HD2, and have found in the last few days, my screen locks and I can't unlock it.
I came here deciding it was a software issue and was going to look into putting Android on my HD2.
I was slowly coming to the conclusion that it was the power button.
If I make an effort to NOT touch it - my phone seems happy.
It's amazing that we're all having the same problem about 2 and a bit years down the track since the HD2 was released - almost a built in expiry!!
And yeah - lots of details on how to fix it would be great.
The HD2 is too good-a-piece of hardware to allow a ****ty hardware button to be the cause of it's death.

New Keypad Button Flex Cable Ribbon For HTC HD2
Copy this:
New Keypad Button Flex Cable Ribbon For HTC HD2 T8585 and paste it on ebay, it will bring the buttons for the htc hd2. I belive they all come from china, but after I test them I will let you all know if they work and if they are worth it.
Copy this: REPLACEMENT DIGITIZER TOUCH SCREEN LENS for HTC HD2 T8585 and paste it on e-bay and it will bring you the digitizer for the hd2.
copy this: http://www.youtube.com/watch?v=YdOC3Xxo_k0 and paste it on your web browser, and it will lead you to a video on How To Replace Repair Disassemble Screen Digitizer. When it gets to a part that say that you have to put the phone in a oven, is just to melt the tape or glue holding the screen to the phone. I just used a hair dryer to war the screen enough to carefully remove the screen and the digitizer from the phone without breaking them, It works. I will be back soon with more info. I believe my digitizer screen is on the mail box now. Will report back...

I have same problem. Today I bought a flex cable ribbon and waiting for the dispatch (estimated in 2 days). I will also report back..

Same problem here!
Hope to hear soon that this is the way to go to fix it

You have to stick back the tape in the housing. The tape is electrically conductive. It connects the ground of the keyboard flex cable with the ground of the housing.
Copy this: REPLACEMENT DIGITIZER TOUCH SCREEN LENS for HTC HD2 T8585 and paste it on e-bay and it will bring you the digitizer for the hd2.
Click to expand...
Click to collapse
Be careful! There are two types of digitizer:
- Solder version http://www.parts4repair.com/htc-touch-hd2-touch-screen-with-digitizer-solder-version/
- Socket version http://www.parts4repair.com/htc-touch-hd2-touch-screen-with-digitizer-socket-version/

Be very careful when ordering parts, specially the digitizer they have several kinds, solder and socket, and different socket sizes. Compare parts with the ones in your cell to make sure, don't just believe the advertisements.

Hi, any updates on this? I'm also having this issue, but in my case, even pressing end call really really hard doesn't solve the problem... snif..

+1 on that
i pressed all the keys even the lower part of the LCD & flashed new roms but no joy :crying:
will bring to shop instead I'm afraid to open it up, it might end up even worse

Just be extremely careful when you try this. That flex cable is so incredible fragile and easy to tear. My roommate tore the volume rocker section right off of his HD2.

Hi dragonsuicida
Were you able to get your touchscreen to work?