Hi,
yesterday, my Mini went cracy. EITHER the hardware buttons OR the touchscreen works. Neither hardreset nor ROM update couldn't help. Is that a known issue?
Thanks for any hints.
Mine hang for a second time now. No observed pattern. It just froze out of the blue. You can only operate the power button. Restarting the phone will put you in the perpetual boot up "windows mobile" red splash screen. Only cure is to hard reset. And lose all your data.
HD mini is really really weird. It seems this unit had been rushed out of production without any kind of inhouse testing at all.
Sense on HD mini is very slow and buggy.
Related
Hello everybody,
After flashing an Elfin Rom to my Elf, my Elf stuck at there colors screen. Vodafone-Shop was quite helpful and they sent me a new Elf
I have been using the new Elf for about 3 weeks and for the third time (happens almost one time in a week), my Elf does not recognize, that i press the power button. If the display was off, i see that the led blinks and even the long pressing of the power button does not change anything. The only solution was a soft reset. Today i lived it again, but this time the display was on and it did not turn off. Holding the power button for a few seconds and restarting was the solution.
Has anyone the same problem or any ideas why it can happen?
Thanks in advance...
Erkan
On my HTC Touch (P3451) I have the same problem: The phone randomly freezes in such a way that I have to do a soft reset. Also, when the phone is on stand-by, when I press the On/Off button (to turn the screen on) nothing happens... neither if I press any of the other buttons (green, red or camera),despite of this, the green led of the top still blinks... Some other times, it justs restarts by it's own, no matter what I'm doing (a few time during today screen, some other using office, a couple listening tu music, and a lot of times when it was on stand by in my pocket).
Also, the phone loses the cellular signal very often (I don't know if that is related to the freezing problem).
I've tried doing a hard reset an using it without any 3rd party programs installes, but the problem persist.
I tried taking it to the vendor in Lima (where I live), but they say that because thre's a small scratch on the case, the warranty is void...
I don't know what to do about this... Any suggestions? please?
This is a hardware problem, This problem is associated with faulty motherboard, and suddenly, in a few days you will notice that phone will stop getting power on, it generally happens when phone falls on hard surface from a height, may due some dislocation of micro soldering. Its better you report to service centre, if the phone the phone is in warranty, they will replace motherboard free of cost, only issue is your device IMEI number will change with motherboard replacement.
i think the problem was something to do with the software. i flashed the Junior version of Onyx ROM with Windows Mobile 6.1 to my Elf, which has YouTube and GoogleEarth preinstalled and is memory-friendly at the same time. Now my Elf does not freez anymore.
I think it's a software problem.
I flashed a lot of ROMs in my Elf but, after a flash version 3.1.1 of really great Onyx Sr., the phone starts to have a bad behavior. It's freeze a lot and the green led still blinks.
I will try to use normal light off and shutdown method instead of using ShutXP to try. But it's definitely a software problem.
--
Marcos Guimarães
Brazil
HI marcosvafg,
i have done the same like you, marcosvafg. but unfortunately my touch is lost in black-screen-smart-moblity-screen-space. can you give me a detailed description what you have done to restart your mobile phone?
i did this:
- go into bootloader
- start to install new rom
but every rom i used i got an error (image is corrupted, wrong model ID). which rom did you use?
many thanks
alex0123
I had a problem where my Elf started freezing almost after me entering the PIN. It is true that it got a rough drop just before doing it, but no serious damage was done to its skin.
I got it to the company and they changed the motherboard free of charge.
Hi guys,
i think gagandeepbains is right that this is a hardware problem. Because i lived it many times with some other cooked ROMs, and i can say that it is happening mostly when the temperature in the environment is low. maybe it is a reason, why this happens usually, when leaving the mobile on overnight...
after flashing my original ROM, i"ll give it back to Vodafone and ask for a change.
for you all, if you still have warranty, bring those back (and who knows, maybe you get an ELFIN instead of an ELF).
the same thing happened to my elf when i first got it back in august last year.
was a hardware problem, orange UK sent it to HTC for repair and i got it back 3 weeks later with a new motherboard in the phone,
also got a surprise to find that they had also upgraded the memory.
i sent in an elf and got an elfin back.
i thought that was a nice surprise
alright.
but to make sure, you can always upgrade to 03.21.90 radio.
thats the most stable one.
I had the same problem but with coocked roms (rarely with the original one)
early onyx roms had a bug with ELF but not in new roms
If still in warrenty try to change it again
I have a Sprint Touch [Vogue]. It has served me very well up until recently.
One day, I was using my phone normally when the battery died. No big deal right?
Well, I charge my phone and reboot it. For some reason, Windows is EXTREMELY slow and unresponsive. I figure that something vital had been corrupted by the battery's death, and that it was nothing that a hard reset couldn't fix.
I performed a hard reset.
I let the utilities for the first boot run to customize the phone. Everything seemed pretty much normal. I configured my settings, re-added my contacts, etc. Then I turned the screen off [with the power button].
I turn it back on later to do something. I touch the screen. It immediately and accurately detects the touch's location, but it continues detecting a touch. For 20-30 seconds, after the input has stopped.
It was strange, so I soft reset the device. It booted, with the same problem. So I performed another hard reset. I did some configuration [the response acting normal at this point], and then turned the screen off. Turning it back on brought the same problem back.
This problem still exists on my phone, even after numerous hard resets and even ROM flashes.
A better description of the problem: When the device is first turned back on [meaning brought out of standby], its touch response is messed up. It will immediately and accurately detect any touch input, but it will continue to detect the input for up to 30 seconds AFTER it has been released, as if you were holding it the whole time.
WHY is this???? My phone is almost unusable because of this!!!! I can still place/ receive calls, using the navigation buttons and the red and green buttons. But the touch response is screwed!
Can someone please shed some light on this problem I'm having?
Phone specs: Windows Mobile 6.1, HTC / Sprint customized. Minimal third party software is currently installed.
[I've already determined that third party software is not the problem, because i haven't installed any!]
Possible solution
Hi,
today I experienced something similar to your description - no touch response when I tried to pickup a call. The strange thing is that last night everything was working and no settings were modified nor programs were added/removed. The screen suddenly 'died'. At the moment I am using it through a program MyMobiler which brings the mobile display to the PC and I can use the mouse to control the phone (it is like VNC for the phone screen, the phone is connected with ActiveSync).
This is temporary solution untill I finish my backups of files, programs, settings. I didnot performed hard reset yet, hope this will solve my problem
In the following link there is a 'magical' solution - to remove the screen protector:
http://www.htcwiki.com/thread/1112981/LCD+or+Touch+screen+not+working
P.S. I had removed the screen protector and voilá - the screen is now touch responsive. The root cause of the problem obviously is the dust between the screen and the protector which results in constant screen pressing - and as a result no accepting my finger presses.
I hope this will work for you and others with similar problem.
I had a similar experience with an old Vogue.....In my case, there was no battery death precursor, but it just started acting up. Not too long thereafter, I noticed the screen/digitizer was forming what looked like an air bubble between the digitizer and the LCD on one place of the screen. The screen was becoming defective. I eventually had to buy another Vogue from a friend who didn't have a clue of the 6900's potential, and didn't want his anymore, so I got it cheap.
Sounds like your screen/digitizer may be on it's last leg.
I had a strange issue recently with my build (below). I had a 'normal' data freeze and rebooted, but when I did, apparently a message was waiting and some appointment on my calendar was due. This seemed to really slow down WM and HaRET ran very slowly before booting Android. However, after Android booted, the touchscreen was locked and wouldn't slide out of the way. In fact, the screen darkened and shut off just as if I wasn't touching the screen at all. I did receive a phone call, which worked, but touchscreen was still unresponsive.
So I tried rebooting again. This seemed to lock up JMZ Dual Boot and not allow me to boot up Android. Moreover, it locked my touchscreen in WM! I have pocketshield installed, and after cover screen showed up, I couldn't move it away. I tried rebooting, taking the battery out for 5 minutes, etc. and no luck.
Ultimately, I resolved this by a HARD RESET of the phone. Lost my windows setup which will take some time to repair, but since I use Android most of the time, maybe it doesn't matter?
Anyway, posted this in case others are having this problem, maybe there's a theme.
editted: ok, touchscreen stopped responding again, in WM and Android, while the unit was just sitting on my desk. I'm now thinking hardware problem...
yes i have the same problem since a ~week. NO TOUCHSCREEN... i have flashed maybe 100 different roms, but no luck... even when i install the original vodafone rom with radio and downgrade to spl 1.48 it doesnt work... this must be an android issue i think.
yesterday i was in the vodafone shop and they give me an NEW HD2 ))))).
now im waiting for an solution about that problem and hope someone will fix it. untill that i will stay on WM6.x. i dont think, i will get another new HD2^^
sorry about my bad english! im german...
ps: when i started the hd2 there was an picture of an WORLD MAP for ~one second. maybe this helps. i think there is something in the front of the orange screen. something with "yes" or "no" option. but i cant see it.
Alright, so here's my problem. My touchscreen won't response to any finger movement. I could press the hardware buttons like power, volume and talk and it response to that but my problem is mainly trying to get inside my rom. I tried flashing rom via NAND and via clockwork mod and nothing helps. The G Sensor seems to work just fine because it rotates the screen when I'm inside my ROM. I could go back into MAGLDR but I don't think anything there is going to help?
Has anyone else experience anything like this and if so, what did you do to solve it?
had same problem, found a FIX
i have had same problem past couple of days. i was running darkstones SuperRAM_FroYo_V1.5 build with oz 2 cleanex rom. i know that every now and again it would be a pain to unlock the device with the agonising wait for the lock screen to show up but this time the touch screen would not work at all not recognising any movement and not dragging the unlock button across. i would have to take the battery out and restart, even some times touch screen would fail completely when in winmo too, got to a point when 3 days of working then not working and taking the battery out a million times to boot back into android to unlock the device, then touch screen died completely.
FIX- Hard reset
will reset windows mobile. all data on device will be lost.
hold down up-vol key and down-vol key, soft reset button and then power button till it displays formatting screen. follow on screen instructions.
hope this helps.
tidygrant said:
i have had same problem past couple of days. i was running darkstones SuperRAM_FroYo_V1.5 build with oz 2 cleanex rom. i know that every now and again it would be a pain to unlock the device with the agonising wait for the lock screen to show up but this time the touch screen would not work at all not recognising any movement and not dragging the unlock button across. i would have to take the battery out and restart, even some times touch screen would fail completely when in winmo too, got to a point when 3 days of working then not working and taking the battery out a million times to boot back into android to unlock the device, then touch screen died completely.
FIX- Hard reset
will reset windows mobile. all data on device will be lost.
hold down up-vol key and down-vol key, soft reset button and then power button till it displays formatting screen. follow on screen instructions.
hope this helps.
Click to expand...
Click to collapse
well i have woke up this morning to be able to unlock my device to then locking it and not being able to unlock it again!!! i had notification to say it had managed to restore 16 apps whilst i had been asleep so i am thinking there is a dodgy app out there some were
mazdarider23 said:
Alright, so here's my problem. My touchscreen won't response to any finger movement. I could press the hardware buttons like power, volume and talk and it response to that but my problem is mainly trying to get inside my rom. I tried flashing rom via NAND and via clockwork mod and nothing helps. The G Sensor seems to work just fine because it rotates the screen when I'm inside my ROM. I could go back into MAGLDR but I don't think anything there is going to help?
Has anyone else experience anything like this and if so, what did you do to solve it?
Click to expand...
Click to collapse
Sent from my PC36100 using XDA Premium App
I have this problem and have found no way to fix it, I have tried everything except possibly going to the clk loader instead of magldr. when i put the phone to sleep with the power button is when i have the issue of not being able to unlock my phone in Android. I have tried task 29, going back to original windows roms, sd and nandroid, it is a hardware issue related to the digitizer as far as I'm concerned. I love my HD2 and really need to fix or find another one. I know this doesn't help, but maybe a little more insite if nothing else
I had the same issue. With my 1st HD2 it started as an intermittent problem, then eventually completely stopped working. With my replacement it just started to happen again. I immediately flashed back to stock tmo windows and the touchscreen would work so long as I did not try and put the phone on standby or wake the phone using the end key. If the phone went to standby on its own, the touchscreen would not work either. I changed the settings so that the phone would not go into standby at all. I then learned that locking the phone from the windows menu and allowing it to go to standby that way somehow averted the touchscreen problem. After 2 days, the problem seemed to resolve itself, almost completely. If I try and wake it using the end key, the touchscreen still wont work, but every other button on wake works. Also, putting it in standby with the end key seemed to not cause the problem any longer.
I dont know if the issue varies per person, but what worked for me was going to stock windows for a couple of days, then starting over with android. I guess it depends on how far along the problem has progressed.
Look at my thread in my Sig about the Unresponsive Screen Solved. This sounds exactly as that. And there are various workaround solutions through out the post.
The problem began randomly while using CM7 Barebone. Upon boot, the phone works as usual. However, it would stop responding to my touch when I would try to slide the unlock screen. I would have to turn the screen on and off a couple of times and finally it would respond again.
I assumed it was a ROM issue, so I switched over to Paranoid Android, however the problem is happening on this ROM as well. Initially, I assumed it was a hardware issue, but the phone works perfectly fine right after I boot it back up.
Does anyone have some idea as to what could possibly be happening? I'm worried that this will just get worse and I'll end up having to purchase a new phone.
Search for unresponsive screen, your issue is likely to do with the digitizer. When you Held down the power button to reboot the phone this temporarily fixed it (it's a known temporary fix). Install some sort of lock screen widget so that you don't have to use the end call button too much, and unlock using any of the other hardware buttons.