Related
I thought I should share this with everyone in case it helps someone out there. I might have gotten lucky, so YMMV.
Basically like everyone else my SGS (I9000M from Bell) died due to an internal SD error, but in my case I haven't updated the phone since I got it in September 2010 (it had the JG9 firmware). The good thing is I was able to flash it to the stock Froyo 2.2, and I'm currently using it as normal and can access the internal SD without problems.
Summary of steps that most likely fixed the problem:
Go into recovery mode and "wipe data/factory reset". If your phone boots (but still have problems accessing the SD card) then it's a good indication that you maybe able to fix it.
Flash JL2 (from samfirmware.com) using ODIN. Not sure if this is needed, but you may need to ask ODIN to Re-partition. You still get an error "Can't mount DBDATA", and the phone won't boot. That's ok.
Flash the SpeedMod Kernel using ODIN (I used SpeedMod K12J with HZ=256). Your phone should boot into JL2 and the SD card should be accessible again.
At this point your internal SD card is fixed and you should be able to flash whatever you want. Just note that Kies will sometimes not work properly with the SpeedMod installed. In my case I flashed 2.1 (JH2) again (this won't work if you have 2.2 without speedmod kernel), then used Kies to update to 2.2 (JL2).
For those who are interested in the details, please read on.
Bought the phone in September, it's a Samsung Galaxy S I9000M from Bell. It says 10.07 on the back of the phone, and it had the JG9 firmware on it.
Since the 2.2 update came out I've been following closely the problem of the internal SD failures and the grief it's causing to a lot of people. So I decided to hold off updating until Samsung gets their act together. (I know it's better to update as soon as possible in case it dies so that I can use the warranty, but I had 9 months remaining so I decided to wait a little more.)
Close to the end of 2010 I noticed that my Android Market has changed, and that it now allows me to "Update All", so I just hit that and noticed that after updating several apps, all the remaining updates failed. I knew this wasn't a good sign. My SD card was still fine though.
After the above incident the phone felt a bit sluggish and less responsive than it used to be. I hadn't correlated this to anything yet, but now I know it was most probably due to the internal SD on its way to die.
On January 7 the phone suddenly died. When I rebooted it, I got the infamous symptom of seeing the S logo animation then black screen, then if I touch the two buttons at the bottom they light up indefinitely. At that point I knew it was the internal SD card.
I put the phone into recovery mode and confirmed my guess when I saw the red error message "Can't mount SDCARD".
I took the phone to the Bell store, the guy told me Bell now has an expedited shipping process for this problem and gave me a number to call to get a new replacement phone.
I called the number and they verified the symptoms with me, and said they're going to send me a new phone. I asked for the $100 credit but I was told I can't get it since I didn't update to 2.2. Apparently they only give you the credit if you actually tried to update and the update caused the phone to die (which doesn't make any sense to me).
So, while waiting for the new phone to arrive, I decided to try a few things. Here's what I did:
First thing I did was going into recovery mode and doing a "wipe data/factory reset". To my surprise, the phone actually booted after I did that, but I got force closes on almost all apps, and when I checked the internal SD card it wasn't mounted at all. The phone response was extremely slow and barely usable. I was able to make phone calls though.
I wondered if the SD problem is a corrupt partition rather than a physical error. After searching for a while I found someone posted a solution to fix a problem with his internal SD card by using the "parted" tool to mkfs the partition. Unfortunately I couldn't copy the tool using adb; my phone wasn't rooted and I couldn't access the SD card, so there was no place to copy the binary to. I get either a read-only error when trying to copy to the root, or a permission denied error when trying to copy to other mounted partitions.
Then I figured if I could flash 2.2 somehow (even if it doesn't work) I can try to ask Bell for the $100 credit Kies was useless as it couldn't recognize the phone, so I grabbed the stock JL2 firmware from samfirmware.com and used ODIN 1.7 to flash it. I asked it to Re-partition (not sure if this was needed). After reboot I saw another red error message, but this time it was complaining "Can't mount DBDATA" (as opposed to SDCARD). Then all reboots after that resulted in the same problem (S logo then black screen).
I searched for the "Can't mount DBDATA" error and found a post on xda that shows a method that should fix this by first using a 512 PIT file to repartition (no ROM involved), then flashing a stock firmware. I did that but it didn't help.
Then I found a site called "AKA skriller" that shows a way to reflash a stock firmware after the phone is bricked. So I followed the instructions by flashing a "nobrick" image (apparently made by someone called eugene), and then flashing a stock firmware. I flashed nobrick then JH2 in attempt to go back to 2.1. After doing this the phone went into a boot loop where it keeps showing the I9000M screen then rebooting. At that point I couldn't go into recovery mode, but I could go into download mode.
After searching again I found out that this was due to a new bootloader in 2.2 that prevents going back to a 2.1 firmware. I wanted to stop the boot loop so I flashed JL2 again, which stopped the boot loop but still the phone won't boot (black screen).
After more searching I found that I could go back to a 2.1 firmware only if I flash a custom kernel, someone suggesting the SpeedMod kernel (not sure if it has to be SpeedMod or any other kernel). So I flashed SpeedMod (I used SpeedMod K12J with HZ=256) using ODIN 1.52. First thing I got is a custom recovery menu with more options, I just skipped it and rebooted. THE PHONE ACTUALLY BOOTED this time into 2.2. Not only that, but the SDCARD problem was FIXED, and the phone was responsive and fast again.
I wanted to load my contacts again using Kies from a backup I made earlier. Kies recognized the phone but for some reason the contacts widget keep saying "please connect your phone" and I couldn't copy back my contacts.
I thought this might be due to the custom kernel and I was right. I flashed a stock 2.1 (JH2) with a bootloader included using ODIN. It just worked. I could copy my contacts again back to the phone.
I was also able to update to 2.2 (JL2) again using Kies this time, and it even kept my contacts. This is what I have now on the phone.
P.S. I can't post external links due to a restriction by the forum (since I'm new).
I had my doubts when I opened this thread... I've gone through 5 phones already and just finished killing my sixth...
I had tried flashing JL2 stock after killing it through the usual process (transferring over my music collection)... and got the EXACT same errors you wrote about.
What I didn't try was then flashing the custom kernel... so I tried that...
and it was too good to believe... didn't work for me. after the boot animation, display goes blank and buttons off... you can tell it's not going to work if it starts vibrating during boot.
I'm sorry it didn't work for you. As I said I might have been lucky.
Although that I just found another thread on androidforums where the guy managed to fix his sd card in a very similar way to what I described*. I actually haven't seen his post before I fixed my card, so it was independent.
Here are the commonalities between what I did and what he did:
* We both flashed a 2.2 firmware with a PIT file and Re-partition (using ODIN)
* We both got the black screen afterwards
* We both then flashed a custom kernel with no Re-partition
* We both got recovery menu right after flashing the kernel
* We both ended up in Android 2.2 aftwerwards with the SD card fixed
Here are the differences between us:
* I used JL2 firmware while he used JPM
* I used a 512 PIT while he used an 803 PIT (that's just what samfirmware.com said to use for each firmware)
* I flashed the firmware using ODIN 1.7 while he used ODIN 1.3
* I used the SpeedMod kernel while he used the YAOK kernel. He flashed using ODIN 1.3 while I flashed using ODIN 1.52.
* Once in the recovery menu I rebooted right away into 2.2, while he "ended up selecting every option that had something to do with mounting, formating, erasing. Anything to do and sounding to do with the SD card [he] pressed." then rebooted successfully with no SD card errors.
(*)http: //androidforums.com/samsung-galaxy-s/235987-clueless.html
what slaman encountered was REAL hardware failure, like I did
what you encountered was just a Corrupt SD card, which can be fixed all the time, using the process you described, and many other methods.
Real hardware failure, even if you manage to boot into the OS, it will show no internal SD, or 0 available space, or simply an error message complaining about the internal SD
You can only see that with custom ROMs, with a stock ROM you wont even get past the black and white SGS logo screen
internal SD card
Hi,
I have followed a few discussions on this board as also my internal and external SD card was "gone". I couldn't access or mount it any more after flashing with Odin to european JPY 2.2.1 ... and I found out where at least my internal memory has gone.
In fact the internal memory couldn't be accessed after installing an exchange email account. My OWA account requires security like password protection and NO external SD card.... but it seems that version 2.2.1 does not make a difference between internal and external SD card and removes the access to both away. It looks like disappeared but it comes back after uninstalling your exchange email account.
May be this is all known and logic but I couldn't find the explanation to it therefore I would like to post the information.
Thanks
Thank you very much for this! I indeed had the mpbk01 (whatever) error, and did exactly what was posted above (using 512 pit, and 1.7 odin) and now have my pone working just fine.
Again, thanks a lot for the post!
Edit: While all this is true.. seems like i have 0.00b of internal phone storage available, so I cannot install any apps. The internal SD card space is reporting normal at 13.03gb though.
Glad it worked for you. Hope you can solve the internal phone storage problem though.
As I mentioned I might have been lucky, I don't expect everyone to be able to fix the internal SD card problem by just flashing custom roms/kernels. If it works for a few people then I'm happy I saved them the hassle of going through Bell to replace the phone.
just a suggestion to send it out for repair, before you run out of warranty
Uss_Defiant said:
Thank you very much for this! I indeed had the mpbk01 (whatever) error, and did exactly what was posted above (using 512 pit, and 1.7 odin) and now have my pone working just fine.
Again, thanks a lot for the post!
Edit: While all this is true.. seems like i have 0.00b of internal phone storage available, so I cannot install any apps. The internal SD card space is reporting normal at 13.03gb though.
Click to expand...
Click to collapse
uys I have a very serious problem. I'm on Darkkys latest rom...
I took out my battery for 1 hour... put battery back in and the phone did not boot up.
All I got was the screen saver and the phone kept on virbarting...
I tried wiping cache through clock work recovery, resetting to factory settings via clock work.. still nothing..
I just updated phone via odin to latest JPY...the phone goes to black screen and keeps vibrating... It won't boot.
Guys what's wrong with my phone? I am really worried...and I need to use it
I appreciate your help.
Ps. Phone can go into download mode..
Edit: XWJM8 worked
jUsT2eXy said:
uys I have a very serious problem. I'm on Darkkys latest rom...
I took out my battery for 1 hour... put battery back in and the phone did not boot up.
All I got was the screen saver and the phone kept on virbarting...
I tried wiping cache through clock work recovery, resetting to factory settings via clock work.. still nothing..
I just updated phone via odin to latest JPY...the phone goes to black screen and keeps vibrating... It won't boot.
Guys what's wrong with my phone? I am really worried...and I need to use it
I appreciate your help.
Ps. Phone can go into download mode..
Edit: XWJM8 worked
Click to expand...
Click to collapse
well I have this problem and cant get it sorted at all, it seems to have also created another partion and i have no idea how to wipe the sd card clear of all partions so it can recreate them!!!!
please help !!!
Hii there,
this thread seems to be very helpful, so I want to value your help with something in return. if any of you can get me out of this mess I will donate you appropriately so that you can constantly offer this helps to others too.
some details are as follow:
1. my Galaxy S (korean) M110s was on USB downloading Market update when I disconnected it abruptly to make a call. It was downloading some updates then.
2. moment than its showing SD card damage error and even showing 00 for external SD card which I inserted post that.
3. this means neither internal nor external SD card are being detected. Though it shows that ext SD card is mounted when I insert in and also let me unmoutn it.
BTW I have tried flashiing using odin and eclair 2.1 version which didnt help much.
Need urgent help
usb jig only gets me into download mode. and not recovery mode
so can Odin still get it to work while in download mode instead
It worked for me but I can't access the internal memory nor the external one. Hence, I can't use the camera or install any app. I don't have any kind of warranty so I believe this is the best I can get, right?! At least I can use as a phone and browse the internet!
Thanks for your help, even though it worked half-way for me!
http://forum.xda-developers.com/showthread.php?t=1020278
Please take a look of this thread:
http://forum.xda-developers.com/showthread.php?t=1188482
It may fix your internal sd card problem permanently.
Hi I've searched for many hours for a solution so I've finally decided to post a query on XDA.
As you all know, the Samsung Galaxy Y has a small internal memory - in a bid to expand it I did the following:
1. Rooted my phone using an update.zip file - this created superuser on my phone.
2. Using CWM Recovery I made a partition with 512MB
3. I installed the Link2SD app.
4. Upon opening the app I chose "ext3" to link the internal memory with. This caused my phone to reboot.
5. Upon reboot, I found that the SD card memory (supposedly 2GB) had reduced to 1.35GB which was lower than expected.
6. Wanting to un-partition, I used CWM Recovery to format all parts i.e. /cache, /data, /system etc.
7. The phone did not boot up despite waiting hours...
8. I used Odin mode to flash a stock rom which did not finish correctly despite trying several times, however when I detached my phone from the USB, I was able to boot it up and start it normally.
9. After booting it up, no apps would install despite many different methods trying to install them.
10. I launched into the standard recovery mode and did factory reset.
11. Now the phone functions normally except for two things that I've noticed:
- I can't perform a software update for my phone, the 0.38mb file downloads and as it is installing (before booting up), it reaches 22% and then the phone starts and gives the message "failed to update firmware" or something of the sorts. Also in Samsung Kies, I get the message "GT S5360 does not support initialising" when trying to update.
- Even with the packet data on, I don't get a 3G symbol at the top of my phone and I can't connect to the internet. This is the major issue in this post.
Apologies for the long post, but I've done a heck of things so I wanted to include all information. If there's any god amongst you guys who can help me then I will be very grateful.
P.S. I live in the UK and I am on TalkMobile!
I am idiot - ignore this.
Hey guys
Just got a S5 (previously owned a S2 and S4 Active, which I have rooted and put custom ROMs so many times. Hence I'm familiar with Odin, Recovery, etc etc).
About a week ago, I installed Shohat v5 ROM, everything went fine. I was quite happy with it.
I installed back my app from my S4 Active through a big update.zip (backed up with Titanium paid version) thanks to custom recovery.
And just now, when my battery was like 5% left, I decided to make a hard reboot (as Xprivacy warned me that I needed to restart to have my changes into effect).
I charged my phone and THEN I push the reboot button (not the hot boot).
While charging, the screen went normally black, but stayed black with the blue LED notification ON (not sure if that info is important).
Then, black screen stays forever:
- no logo
- no download mode
- no recovery
- When phone is connected through USB to my laptop, I hear the usual "tadaam" sound from Windows, but no "USB notification".
It seems a JIG would be the solution, but no idea if that would work for a S5 (I guess Samsung has now worked to avoid that solution)
Well, if anyone can help, that would be cool
Obvious I know but you have pulled the battery for a while and tried again right?
Sent from my SM-G900F using Tapatalk
Goldie said:
Obvious I know but you have pulled the battery for a while and tried again right?
Sent from my SM-G900F using Tapatalk
Click to expand...
Click to collapse
Hello
Indeed, I just removed the battery for a few hours a tried, no success.
But is it normal that a hardbrick can occur 1 week after installing a custom ROM?
Right now I can't bring it to Samsung store for repair...
(Adding a new post as editing is not working properly)
Isn't there a way to use ADB with commands through Windows (as there is the "tadaam" sound when I connect it through USB)?
A friend of mine bricked his Nexus tablet and went through such solution to remove the brick ...
OK ............
Here's the magic
After removing on and off the battery many times, trying to boot in recovery or download (trying about 15 times)
Now I managed to boot in recovery (I was like "huh?" and "wooohoooooo")
Did Wipe cache
Did Wipe Dalvick
No Factory reset
Fixed root (seems like I lost it, no idea why)
Let's see if I can reboot it
I think maybe the issue came from the huge update.zip created from my S4 Active (i9295) with Titanium backup (I was in Android version 4.2.2).
Maybe the reinstalled apps, messed up something as the ROM was in version 4.4.2...
Desanusseur2porc said:
OK ............
Here's the magic
After removing on and off the battery many times, trying to boot in recovery or download (trying about 15 times)
Now I managed to boot in recovery (I was like "huh?" and "wooohoooooo")
Did Wipe cache
Did Wipe Dalvick
No Factory reset
Fixed root (seems like I lost it, no idea why)
Let's see if I can reboot it
I think maybe the issue came from the huge update.zip created from my S4 Active (i9295) with Titanium backup (I was in Android version 4.2.2).
Maybe the reinstalled apps, messed up something as the ROM was in version 4.4.2...
Click to expand...
Click to collapse
OK ... bad news again
I performed a hard reboot to check that everything was stable, and phone rebooted fine.
then I turned off and removed to battery to put back the SD card and the SIM card, and now the phone is not being turned on again.
And now the phone is not able to be turned ON again...
What's going on, any idea?
*** EDIT ***
I managed to reboot in custom recovery totally randomly after playing with the battery (removing, putting it back, trying to boot)
I made a full factory reset and reinstalled the custom ROM Shohat.
After rebooting, it went directly to ODIN as it was displaying error messages "ddi: MMC_read failed"
I guess the internal SD card is dead.
Questions:
1/ Is warranty OK if
- KNOX counter is at 0 (no idea why it is at zero)
- Current Binary is set to OFFICAL
- BUT SYSTEM STATUS is set to "CUSTOM"
2/ Can a custom ROM do this or is it a hardware failure?
Did you try with another sd card did you have apps installed on this sd card for me this sounds like a dead sdcard issue with some apps on it. I had the same issue with my X8 when a lot of apps ware running from the sd card btw sd cards are totally unreliably for storing important data as they usually die after some writing on them.
Change the SD Card and I think your phone will come back to normal.
SD Card Reader
Desanusseur2porc said:
After rebooting, it went directly to ODIN as it was displaying error messages "ddi: MMC_read failed"
I guess the internal SD card is dead.
Click to expand...
Click to collapse
I don't know if this helps but I had an GS-900H (S5 octacore version) and struggled with it for a week trying to debug this problem, ordered new memory cards, installed different ROMs, etc. only to find out that the card reader was bad.
In my case it would corrupt the card every time so that my PC would need to 'repair' it before I could begin using it in the PC.
Maybe the card reader is a common point of failure?
EDIT: I also had issues with different cards working and not working based on the speed of the SD card (different S5). I know for a fact that it will switch you over to main memory when taking pictures that require advanced features -- I got a popup telling me that my memory card wasn't fast enough.
alex_tytn said:
I don't know if this helps but I had an GS-900H (S5 octacore version) and struggled with it for a week trying to debug this problem, ordered new memory cards, installed different ROMs, etc. only to find out that the card reader was bad.
In my case it would corrupt the card every time so that my PC would need to 'repair' it before I could begin using it in the PC.
Maybe the card reader is a common point of failure?
EDIT: I also had issues with different cards working and not working based on the speed of the SD card (different S5). I know for a fact that it will switch you over to main memory when taking pictures that require advanced features -- I got a popup telling me that my memory card wasn't fast enough.
Click to expand...
Click to collapse
Hello guys
Thanks for your input.
Unfortunately I do not have an external SD card, the issue is with the Internal memory
So i can not request new ones or try to replace it, or work on the card reader...
Amazing that you are about to lose your phone forever and you don't even consider installing the original Samsung firmware.
What da f*** are you doing?
100%. Numb nut doesn't deserve the great phone It's like he got OCD.
Sent from my SM-G900H using XDA Free mobile app
lcmazza said:
Amazing that you are about to lose your phone forever and you don't even consider installing the original Samsung firmware.
What da f*** are you doing?
Click to expand...
Click to collapse
Hello
Well, not sure that ODIN will work as the internal MMC is not recognized, so where would that be installed?
Furthermore, I'm waiting for the feedback from Samsung (as knox counter is at 0, Binary is set to OFFICIAL and only status is set to Custom).
I did not want to change these counters with manipulating ODIN.
If Samsung gives it back to me with a new one, then wooohoooo
If Samsung says "f*** off, you manipulated it, warranty is off", then I'll use ODIN with STOCK ROM from Samfirmware + PIT file (they are ready for use on my computer)
If you can't get to download mode how do you propose to use Odin to flash stock ??
Sent from my HTC One using Tapatalk
Hello!
I have a problem with my Galaxy Note 3:
On a monthly basis, I do a Online Nandroid Backup to my SD-Card.
After encountering a problem with the PlayStore, I booted into Recovery and recovered to my last "good" backup.
Since starting I had weird problems on my phone and I tracked them down to being a problem with the root access.
I used TowelRoot to gain root access again, but the SuperSU app didn't work. I then upgraded the SuperSU app, by deleting the old and installing the new version from the play store.
(After trying the uninstall function within SuperSU which did exactly nothing)
Since then everything kept working fine, but I encounter serious reboot problems.
With no clear time frame, my Note 3 Screen just freezes for 5 sec, and then the phone reboots. Sometimes I can use the phone 1 hour, sometimes 20 min until it happens again.
I have tried to narrow down the problem over christmas, and have the following points:
When I boot up, I have a SD-Card symbol in the notification bar which shows a sd card with a cog wheel in it. As soon as I enter my password it vanishes. Without the SD Card inserted I haven't encountered a problem, and it runs faster. So I reformated the SD Card in my PC to exfat, then reformated it again in my Note 3 and copied all the Data back (over my PC). After using it for 10 min, it rebooted again. I would really like to use my SD Card. 128 GB can't be the problem because it worked beforehand just fine.
In SuperSU I have set the root access to "allow always without questioning". This didn't change anything. I have fixed the Error from KitKat which blocks write/read access to the SD Card. So no problem there.
The problem still persists. And I have no clue what to do.
Tech Details:
Rooted: Yes (with Towelroot), SuperSU installed/working
Branding: None (International Version)
Micro SD-Card: SanDisk 128 GB
Android: KitKat 4.4.2 (Stock)
Recovery: ClockWork Mod 6.1ish (newest)
XPosed Framework installed
1. Factory reset your phone and flash the latest firmware official for your device.
2. Replace the SDCard for other and make some tests.
Joku1981 said:
1. Factory reset your phone and flash the latest firmware official for your device.
2. Replace the SDCard for other and make some tests.
Click to expand...
Click to collapse
Thanks for your fast answer.
As I mentioned above, the SD Card can't be damaged because it worked beforehand. So I think it is not a hardware issue.
As I have recovered from a working Backup it has something to do with the rights/root access and the SD Card.
Factory Reset is not an option for me, because I spent so much time costumizing this thing that it isn't worth doing it all again.
On the other hand:
I am thinking of Flashing CM 11 and doing a Titanium Backup Restore.
Do you think CM 11 would solve my problem?
Hi! I have a SM-N910F and I think that the internal memory has some serious problems. At first the phone was lagging; next, when I was trying to copy some files for backup I was getting errors on my phone and also on my pc. When I tried to reflash it with kies, I needed two attempts to make it work (phone was stuck at "flashing firmware" stage). The inital setup after restore was painful, as the phone was lagging and not responding (even randomly rebooting). Finally, after I installed some apps, the phone randomly rebooted in recovery mode. My question is: Is there any way to use only the sd card (for system and firmware) and isolate the internal memory? Thanks!
Drake97 said:
Hi! I have a SM-N910F and I think that the internal memory has some serious problems. At first the phone was lagging; next, when I was trying to copy some files for backup I was getting errors on my phone and also on my pc. When I tried to reflash it with kies, I needed two attempts to make it work (phone was stuck at "flashing firmware" stage). The inital setup after restore was painful, as the phone was lagging and not responding (even randomly rebooting). Finally, after I installed some apps, the phone randomly rebooted in recovery mode. My question is: Is there any way to use only the sd card (for system and firmware) and isolate the internal memory? Thanks!
Click to expand...
Click to collapse
I've seen someone do something similar in here before, try and give it a search. But i think it still utilized some of the internal memory for the kernel if i remember correctly.
Also what kind of errors are you getting when transfering files?
Diload said:
I've seen someone do something similar in here before, try and give it a search. But i think it still utilized some of the internal memory for the kernel if i remember correctly.
Also what kind of errors are you getting when transfering files?
Click to expand...
Click to collapse
When I transfer files over mtp on windows 10 I get errors like: "Make sure these file are available on PC". On the phone I can't remember exactly what was the error in file explorer.
Random Resetting and Lagging Note 4 - Poss EMMC Mem Failure
Drake97 said:
When I transfer files over mtp on windows 10 I get errors like: "Make sure these file are available on PC". On the phone I can't remember exactly what was the error in file explorer.
Click to expand...
Click to collapse
For the past 10 days I have had the same problem. Random restarts and resetting. Very laggy phone. I have Factory reset it 3 times, and it still has the issues. I am convinced the EMM chip has problems/failed. I have flashed roms many times, and am not new to it. I got the latest stock rom with the PIT file (prob not needed), and set about to flash it. It fails straight away with a "write" failure no matter what I do. Looks like I will need a new motherboard or EMM chip replacement unless there is another option. Kies 3 does not even see the phone. Odin does, but all attempts to re-flash have failed so far.
rammitt said:
For the past 10 days I have had the same problem. Random restarts and resetting. Very laggy phone. I have Factory reset it 3 times, and it still has the issues. I am convinced the EMM chip has problems/failed. I have flashed roms many times, and am not new to it. I got the latest stock rom with the PIT file (prob not needed), and set about to flash it. It fails straight away with a "write" failure no matter what I do. Looks like I will need a new motherboard or EMM chip replacement unless there is another option. Kies 3 does not even see the phone. Odin does, but all attempts to re-flash have failed so far.
Click to expand...
Click to collapse
Odin fails to flash for me too, I think the storage chip is dead. I didn't flash any roms at all, not even root, so probably it is age related. Maybe it works in your case: try to download all files from: https://mega.nz/#F!QIMmFRIT!Ns3AM-n0FUoMqOOWUif9ng!YN9lgLRI except the APQ8084, load them in ODIN in their places (PIT, BL, AP, CP, CSC, ) and try to flash; maybe "NAND erase all" would help, but I am not sure.