I was having a terrible time getting my wi-fi to work on my DroidX. I couldn't figure out what was going on at first. My Netgear N router was coming up as having WEP security when it has WPA-PSK. My Netgear G router would connect, but I couldn't get any data.
But today I figured out what was wrong. I downloaded a wi-fi scanner app and took a look at what wi-fi channels were in play. Not only were both of my routers trying to use the same channel, but other nearby routers were also using similar channels. Armed with this info, I went in and changed the channels that my routers use. My N router now is detected properly and connects, and speed is no issue. Unfortunately, the G router is still giving me trouble, as I can't find a channel for it that isn't being obstructed.
If you're having problems with wi-fi on your droid X, do what I did and find out if there's a better channel your router can be set to. Please leave feedback here if it does or doesn't work for you.
Related
Pardon me because this isn't entirely a Wizard specific questions although I am able to replicate the problem with my Cingular 8125 (new ROM) 100% of the time.
I'm not a stupid person. I've setup numerous wireless networks for corporations and home users. I always use WEP or WPA and never unencrypted (no) security.
In most situations, the wireless router does NOT supply the DHCP to the clients. It usually comes from another DHCP server on the same LAN segment. Typically, this is a Windows server although it could be a DHCP-assigning device, such as a Cisco router.
PCs have no trouble seeing the wireless network and connecting to it and getting addresses assigned to them. For a while, I couldn't do this on WPA security but upgrading firmware and software on the laptops (usually Dell) rectified this.
With my Wizard, both old and new ROMs, I can SEE the wireless networks and connect to them but I can NEVER get an IP address. It tries and tries and fails and fails and eventually gives up. (Yes, the Cingular proxy is turned off)
Yet, at the airport or other public places with free wireless, I have no problems connecting my Wizard to the access point and surfing away. Thus, I know its not (entirely) a Wizard issue. Of course, these public access points aren't encrypted which could be one of the reasons but I doubt its the only one.
As a test, I just built a new wireless router with a SSID (other than "default") and security turned on (WPA) and let the router act as the DHCP server. Wizard connected in seconds and was surfing away. So the obvious next question is: why doesn't this work when the wireless router ISN'T the DHCP server? Other machines (laptops and such) have no problem connecting to one wireless router and getting a DHCP address from another box yet my Wizard cannot.
I've tested this with D-Link and Belkin wireless routers (consumer-grade).
I've seen other people post that they cannot get their wireless to work on their Wizard and while the fix may not be on the side of the Wizard, I think others may be in the same boat I'm in so I'm hoping that maybe we can compare enough stories to narrow this down so that we CAN use our Wizards wirelessly!
Ken
Confusing...
maybe you should try assign a fix ip to your pocket's wifi adapter and see if it would work. or just let the wlan security turn OFF on your access point to see what would happen.
i guess that the network protocol stack is slightly different between a PC and a PPC, which limit the DHCP request route.
I have just purchased the Wizard, aka o2 XDA Mini S, and use it with my Belkin Wireless Access Point (WPA-TKIP Enabled, DHCP & NAT disabled) and Cisco ADSL Router (DHCP Server) without any problems.
I have assigned the Belkin Wireless Access Point a fixed IP address however, but I don't think this would make a difference.
The other thing I found was that the Wizard would not connect correctly to the Belkin using WPA with AES encryption, but switching it to WPA with TKIP works flawlessly.
Well, I suppose its encouraging that others with the same wi-fi routers are getting this to work but its discouraging that I'm having so much trouble!
Fixed IP does work (therefore, its unlikely a Wizard-only problem) but obviously a fixed IP doesn't let me roam from one hotspot (home) to another (work) very easily.
Haven't tried it sans-security yet although that might just prove a point, rather than be a perminant solution. I have tried WPA-PSK and WEP with the same (negative) results.
I personally have found that unless I change the power settings for the WiFi adapter to full power, its hit or miss.
Never have a problem maing connections, geting leases, etc with it there.
YMMV though
Regards - John
prob irrelevent
i found that before i active sync'd. the wireless monitor on my wizard showed a strong signal from the router. then after it synced, it picked up an IP from the servers dhcp fine.
also for lightweight simple security i use mac address filtering on the AP
I know Google has said they are looking into it. But this is ridiculous. The N1 can not handle WPA2 connections. Even though it saves the connection and password, it almost never reconnects automatically. From what I was reading on the Google help forum, it appears to have compatibility issues with many retail routers and they suggest upgrading the firmware on our routers. Throughout my day, I may connect to 3 different APs. One is a standard Linksys wrt54g with sveasoft, the others I connect to are Cisco APs.
None of them automatically reconnect. Most of the time on the Linksys, I have to delete the connection on the phone and re-add it.
I still like this phone but between the 3g and wifi issue, it is a pain to use.
I won't pretend to understand all that you just said, but I can tell you that my router is set up using WPA2-PSK. Not sure if it is the same as just WPA2 but my N1 reconnects to mine whenever I get in range. Then at the office it will connect to the WPA2-PSK set up in there, and one more regular open connection that is available at our pool. Pretty much every time I look at it, it is connected to one of those 3. Or else if I am OOR of any of those, I am on 3G.
My home router is a Belkin -N. Work routers are a Netgear -N and a D-Link -N.
I've got a Netgear WNR2000 on WPA2, and I can confirm I occasionally have this issue with the phone not connecting to the network automatically. It usually does if I go into settings and touch it to reconnect again.
There is an easy solution for any WIFI problems, use a Mac Filter!!
I have to go into Settings > Wireless & Networks > WiFi Settings before my Nexus One will reconnect to my home router, which is also using WPA2-PSK.
Hopefully it'll be sorted in a firmware update, it is annoying having to go through 3 screens to do something that my Nokia Symbian phones have been doing without issue for almost5 years...
I am having no problems auto connecting to my home WPA2 network, I am using AES encryption and running DD-WRT firmware if it helps.
philaldred said:
There is an easy solution for any WIFI problems, use a Mac Filter!!
Click to expand...
Click to collapse
Mac Filters are no replacement for WPA2 or encryption. Almost every device has the ability to spoof a mac address. Using a mac filter might help quickly eject roaming devices nearby, but it is NOT security.
Its like using a No Trespassing sign to replace locking your doors and windows.
i found that APNDriod may be a possible culprit....
Before I installed APNDriod , every times I go back home, my N1 will connect to my home WiFi almost immediately.
But after I install APNDriod, my N1 will not connect to my home WiFI.....I need to go into the Wireless setting screen, once i am on that screen WiFi it will connect.
But it is strange this I don't have this issue in my office, it just connect automatically before and after installing APNDriod.
Today I tried NOT to use APNDriod for a day and my N1 connect to my home WiFi without issue..... will do more experiment tmr.
Netgear WNR3500 w/ WPA2-PSK. Reconnects every time I am in range.
I find that my Linksys is the worst. The Cisco Aironet 1121 is better, but still has occasional connection issues. And I have not installed APNDroid.
On another note, when my phone switches from 3g to 2g and vice versa, it takes a long time for the data connection to resume
My network at home is setup with WPA2. I have no problems connecting to it... I click on the little wireless icon, and wait for it to say "wireless settings updated" and also wait for the wireless icon to show up near the time... then i will start browsing
I have a Dynalink RTA1025W
My wifi is working now. See h**p://forum.xda-developers.com/showpost.php?p=5773148&postcount=26
No problem reconnecting to my home network with WPA2 . Apple's Airport Extreme.
No problems here connecting to my Belkin N1 router. Connects the moment its in range.
Setup using WPA2-PSK
im having this exact same problem on my D-link Dir 615!
Pisses me off alot, i hope Google fix it!
I found that unless I was on channel 6 or 11 I had issues
AES-CCMP, TKIP or WPA Cisco521G will not connect
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
xoveruk said:
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
Click to expand...
Click to collapse
@xoveruk - Someone must be able to help sort out this issue !
xoveruk said:
My cisco 521AP does not connect using any type of encryption, it only works with open authentication. Expensive phone like this that doesnt work with business class products is a joke.
Click to expand...
Click to collapse
My suggestion is - check what you're doing wrong before assuming the phone is at fault. And check that you're using PSK.
SEC AUTH ENCRYPTION
No security None Open - working
WEP WEP Open - no
WPA-PSK TKIP WPA-PSK - no
WPA2-PSK AES CCMP WPA-PSK - no
android 2.2 on N1, FRF91
I have my Tattoo rooted with 1.6 (can't recall the ROM name) with build number 1.67.405.6. Almost everything works fine except the connection with my home WiFi network. It's a PPPoE connection through ADSL modem. Next in line is the Netgear WG602 v3 WiFi router. At the beginning I couldn't connect at all so I changed the router's ROM to DD-WRT. Now I can connect with the router but no connection to the internet whatsoever. I can ping my router through my Tattoo, I can even open the 192.168.1.1 and mess around with its software but no connection to the internet. It is only limited to my Tattoo as I can connect through my laptop, through my other mobile (HTC S710) and also I can connect my Tattoo with any other WiFi (Secured or Open) with no problems at all.
I tried with no Security, with WEP, with WPA-PSK to no avail. Any other clues?
try running htc mail while you are using your wifi throuf your tattoo it worked for me
What is supposed to happen if I do that? I'm trying it as soon as I get home btw.
Nothing happened
Hi all...sorry for my interference but this problem is similar to mine.
I'm going mad from many weeks trying connect my Huawei Ideos (U8150) to my home wlan through a netgear VG602v3 AP. No way to do this.
Wifi works from my laptop and from my girlfriend's laptop, but from ideos it doesn't.
I turned off all wireless device in my house, I tried with/without WPA, I tried open network from channel #1 to channel #13, tried changing ssid and I also tried praying .
There is a weak wifi near here: it is on channel #1 and its power is between -89 and -82db. My wifi power (data from kismet) is between -50 and -18 db and is configured on channel #11.
In any cases, even if I put my Ideos near to AP antenna the story is ever the same:
- Ideos indentify the wifi network
- Ideos acquire the IP
- I open the browser or the android market and...
- Ideos lose connection...and so on.
I downloaded from work wifi (crypted with WPA) a wifi scanner from app store: it shows me the neighbour's weak wifi and my wifi network which appear and disappear recurrently.
Please, someone helps me (without suggest to buy another AP!!), any suggestions are welcome!!
Have you tried logging into the router and checking the privileges for devices. Some of them have a security element that restricts the use of the internet on newly connected devices until the setting is changed. I had a similar problem with a new laptop.
hope it helps.
I checked every setting to no avail. I still think somehow that my problem is with my router or adsl modem which doesn't connect automatically with PPPoE and Android doesn't have any command or software to initiate a PPPoE connection.
Other than that... Can't find any solution. Until then, I use connectify on my Win7 laptop. The thing is that I have to keep my laptop switched on as long as I'm in the house.
alpick36 said:
Have you tried logging into the router and checking the privileges for devices. Some of them have a security element that restricts the use of the internet on newly connected devices until the setting is changed. I had a similar problem with a new laptop.
hope it helps.
Click to expand...
Click to collapse
thank you for suggestion. I looked in depth but I did not found the option of which you were talking about. The unique solution still remains change the AP!!!
WiFi and Netgear Router
I think I finally found the answer. It appears Netgear routers support something called WiFi Multimedia. Its a QOS methodology. I disabled WiFi MM or WIMM as its sometimes called, as well as Internet QOS and all my problems connecting to web pages, the market, etc. through WiFi disappeared.
Strange that older versions of the ROM supported WIMM (or ignored it) and newer ones don't. But that solved the problem for me with no real degradation of performance on any of my other computers.
Good luck.
A picture is better than 1000 words.
For an application I'm trying to get this configuration working:
Is this possible or not?
WiFi Tethering to a WiFi Router / Network
Yes, IF your wifi router will accept wifi as an input.
If all of the devices need to be on a network OTHER than your cell phone, then yes, you need a router. The router will have to accept wifi as it's source.
If all of the devices can be on the same wifi network as your cell, then you can get a wifi repeater or range extender. Repeaters "extend" the range that wifi will reach. I don't see that as an issue here as should be able to place your cell phone well within range of your other wifi-enabled devices.
I don't immediately see why you can't have all of the devices connect to your phone directly, but I don't know anything about the application you are working on.
What I cannot say is whether this setup could bypass the number of wifi devices your service provider limits you to. I know my hotspot (Verizon) limits you to five concurrent.
I hope I've answered your question and I've helped. BTW - your picture was perfect!
Thank you for your explanation.
This is a very specific setup.
The router is an Airlink NMini and I carry in my pocket. It has to be near my camera for the wifi connection to work. I get a lot of interference from wireless equipment on my photoshoots. The Wifi router is trong enough to overpower the interference (only when used in B-mode). It's hooked up to a 5 volt power pack.
Close to me I have an Android tablet for quick selecting the right images, then the images are copied over to a remote laptop that is used by my colleage to edit the images.
I needed the internet connection for sending the processed images to a ftp server or dropbox, so my clients can download the images.
I tried using the router as a relay/bridge, but couldn't get that to work. Maybe it's possible, but that's higher networking config.
I finally got it to work by connecting the phone to the laptop using usb.
Configured the laptop for ICS connecting the USB-internet connection to the wireless router. Had to set ip adresses manually, becaue the dhcp of the router did not transmit the correct gateway. But as there are only 2 devices attached, that's not a problem after documenting this change.
So I'm good to go for our next photo assigment. Case closed.
Sent from my Transformer TF101
Sweet setup man
I have a weird situation. I have an SMC8014W-G modem/router at my upstairs desktop and D-Link DAP-1360 Range Extender on the main floor. I can connect from wifi being initially turned off to either spot no problem. BUT I cannot move my phone or tablet from one of their locations to another unless I turn off my Tablet`s WiFi for about 5-10 minutes before turning at back on at the new location, or it will not connect. This is a problem with my network, because the same thing happens on my android phone. Still working on it. I`ve seen others across the web talk about this problem with other mobile devices, while saying the problem doesn`t happen on PC type devices like laptops.
To test that out, I turned my phone's hotspot on. Using my tablet I was able to switch between my home connection and my phone's wifi signal back and forth with no delay at all. But moving from my router's location to my repeater's location could not be done unless I waited 5-10 minutes whether it's on my phone or my tablet.
The entire network is on "802.11 G" (can't used mixed mode or N, that's a whole other story we're not going to get into here) and both router and repeater are set to exactly the same gateway, DNS, network name etc. Encryption is WPA2. The only difference between them is that my main router is set to be a DHCP server, while the repeater is not (it says I can leave DHCP Server off if the router's is on. Perhaps that's wrong, I still have to try that). And my router settings only shows WPA2-PSK while my repeater has more detailed options showing WPA2 Cipher Type: AES PSK/EAP: Personal.
omnius1 said:
I have a weird situation. I have an SMC8014W-G modem/router at my upstairs desktop and D-Link DAP-1360 Range Extender on the main floor. I can connect from wifi being initially turned off to either spot no problem. BUT I cannot move my phone or tablet from one of their locations to another unless I turn off my Tablet`s WiFi for about 5-10 minutes before turning at back on at the new location, or it will not connect. This is a problem with my network, because the same thing happens on my android phone. Still working on it. I`ve seen others across the web talk about this problem with other mobile devices, while saying the problem doesn`t happen on PC type devices like laptops.
To test that out, I turned my phone's hotspot on. Using my tablet I was able to switch between my home connection and my phone's wifi signal back and forth with no delay at all. But moving from my router's location to my repeater's location could not be done unless I waited 5-10 minutes whether it's on my phone or my tablet.
The entire network is on "802.11 G" (can't used mixed mode or N, that's a whole other story we're not going to get into here) and both router and repeater are set to exactly the same gateway, DNS, network name etc. Encryption is WPA2. The only difference between them is that my main router is set to be a DHCP server, while the repeater is not (it says I can leave DHCP Server off if the router's is on. Perhaps that's wrong, I still have to try that). And my router settings only shows WPA2-PSK while my repeater has more detailed options showing WPA2 Cipher Type: AES PSK/EAP: Personal.
Click to expand...
Click to collapse
I have a similar problem with my TP-link WA5210G wifi extender.
My laptop connect fine,but my phones for some reason don't want to connect,they just stay on the obtaining IP and don't connect,i have mine in universal repeater.
And my phone and PS3 will just not connect.
I am guessing that you have this thing turned on in "Repeater Mode"?
Are you using it in Repeater or WDS mode?
Repeater but I solved the issue with newer router now it's handing off properly. There's a slight disconnect and reconnect for a few secs when moving between the 2 points but that's liveable
Sent from my Atrix using Tapatalk
omnius1 said:
Repeater but I solved the issue with newer router now it's handing off properly. There's a slight disconnect and reconnect for a few secs when moving between the 2 points but that's liveable
Sent from my Atrix using Tapatalk
Click to expand...
Click to collapse
That's how it should be unless you're using the commercial routers I use at work. Those are generally way above consumer price points, though. Even at my house, I have a four second handoff time between router and AP.