I have network/sim unlocked my Vibrant and it works fine. However, I have had to re-enter it at least 3 times. All of these times it was after a reboot that was done because the phone was locked up or because an app was frozen. After the reboot, it would ask for the sim unlock again. I can enter it and it unlocks and works fine until I have to reboot under the same circumstances. Normal reboots do not cause a problem, only the ones where an app or the phone is frozen.
I thought that once it was unlocked, it was unlocked permanently. Is there a preferred way to enter the unlock code? I am entering it at boot up with a non TMobile sim when it asks for it. Is there a way in the OS that would make it "stick".
Very strange...After searching a bit I have not found any mention of a similar situation.
Thanks for any info.
Related
Hi,
I purchased a MyTouch over ebay which was locked initially. Somehow I reseted the phone and I am into Google screen now without any data access.
I inserted my sim card and it asked for unlock code which I entered successfully (code procured from unlockingonline).
However, still I am stuck at google screen. It does not offer any option to setup APN or WiFi so I can't make any progress. It's kind of a deadlock situation. I tried to turn it off and on again without any success.
What can I do now? Please help.
Thanks
Press the menu button, it will allow you to change your APN.
Thanks AdrianK. It did help.
Hi, I am looking for some help with my Nexus S.
I recently rebooted and changed to a new SIM, and upon booting I am presented with a screen saying "Enter password to unlock", My gmail password wont work and I don't know what password it means.
So i then put my old SIM back, and it still happens! now I cant get into my phone at all, and cant use it!
I even tried a reset, and when I select recovery in the bootloader, it doesn't work.
I do have Prey installed (http://preyproject.com/), and I did forget to switch it off before changing SIMs, but I entered my prey password and that didn't work either.
Please help!
Thanks in advance,
Tris
Ok i have solved this.
It was Prey that had locked my phone, and I had got the password wrong!
At least it shows it will make it really difficult for anyone who steals my phone!!
Hi everyone. I have a Motorola Atrix 4G MB860 (AT&T) that was unlocked, and I was having rebooting problems, like every 10 mins. So I did the factory reset from the Atrix menu, and it seems like the unlock dissapear. It lock again. I put the same code and it keeps saying "unlocking request unsuccessful", and it shows that 1 sec after I enter the code. My radio baseband version is N_01.77.37P. and Im using it on airplane mode right now, so it doesnt reboots again. please help me.
rogercm93 said:
Hi everyone. I have a Motorola Atrix 4G MB860 (AT&T) that was unlocked, and I was having rebooting problems, like every 10 mins. So I did the factory reset from the Atrix menu, and it seems like the unlock dissapear. It lock again. I put the same code and it keeps saying "unlocking request unsuccessful", and it shows that 1 sec after I enter the code. My radio baseband version is N_01.77.37P. and Im using it on airplane mode right now, so it doesnt reboots again. please help me.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1356121
Solved: Sim Unlock Fails With Valid Code
Hi guys,
Recently i installed the ROMs Phoenix 9.4 and Imperium 10.0, both with S5 style. Both works fine, but one thing not. I configured a PIN Password in my phone, but after reboot the system, the unlock mode is set to Slide Unlock (without password), if i wait the screen turn off or lock the system and try unlock, then the PIN Password is required.
This happened in the two ROMs.
Have a way to fix it?
I would like the password was required at first, immediately after the system becomes available.
Sorry for my english, i wrote with some help of Google Translate.
Thanks!
Did you find a solution?
I have the same issue. It used to work but at some point a few ROMs ago t stopped working.
I was told it was the kernel but I have tried 4 and all with the same result, basically the PIN lock does not activate untill 30 seconds or so after the phone boots up.
scott2ride said:
Did you find a solution?
I have the same issue. It used to work but at some point a few ROMs ago t stopped working.
I was told it was the kernel but I have tried 4 and all with the same result, basically the PIN lock does not activate untill 30 seconds or so after the phone boots up.
Click to expand...
Click to collapse
No, I have not found a solution. A partial solution was to activate a Pattern Unlock.
I have just wiped and upgraded my Galaxy s4 to 4.4.2. I would like to fully encrypt my phone and use pattern unlock so I followed this article:
(just google pattern-unlock-an-encrypted-android-phone, I can't post URL)
But even though I have tried this multiple times and unplugged the USB cable (as mentioned in the article) as soon as I hit enter to start the encryption command the screen goes black on the phone and then after about 10min the phone reboots to the unlock screen and it is still unencrypted. I have tried following other articles too but they are all the same in terms of the command you run to encrypt the phone.
Any ideas? How can I get pattern unlock to work with an encrypted Android phone? Yes I know you can't do this via the GUI but then you need to enter a silly long password every single time you want to unlock the phone which is not an option for me. I don't mind entering a long password when turning on the phone but when it comes to unlocking the phones lock screen I would like to use the pattern unlock.
Any one else had any success with this on 4.4.2? Thanks!
BB007BB said:
I have just wiped and upgraded my Galaxy s4 to 4.4.2. I would like to fully encrypt my phone and use pattern unlock so I followed this article:
(just google pattern-unlock-an-encrypted-android-phone, I can't post URL)
But even though I have tried this multiple times and unplugged the USB cable (as mentioned in the article) as soon as I hit enter to start the encryption command the screen goes black on the phone and then after about 10min the phone reboots to the unlock screen and it is still unencrypted. I have tried following other articles too but they are all the same in terms of the command you run to encrypt the phone.
Any ideas? How can I get pattern unlock to work with an encrypted Android phone? Yes I know you can't do this via the GUI but then you need to enter a silly long password every single time you want to unlock the phone which is not an option for me. I don't mind entering a long password when turning on the phone but when it comes to unlocking the phones lock screen I would like to use the pattern unlock.
Any one else had any success with this on 4.4.2? Thanks!
Click to expand...
Click to collapse
Flash a different stock 4.4.2 . maybe its missing some files.