With a broken power button, is there any way I can get my xda2 into bootloader mode so I can change the ROM?
i doubt it unless you take it apart and shortcurcit the to points that the powerbutton is connected to
would prob be easier to put in a new button then i guess
I may be wrong but doesn't the power button actually put the phone into suspend mode?
Would it work to map the "suspend" function to another button (like the calendar button)? Or does a hard reset only work with the usual specific hardware buttons?
no it's not the only function
clicking on a suspece software shortcut
while reseting the device dont result in a hardreset
I have a solution. i have the same problem. Get a paperclip, and insert it into the hole where the power button should be. Slide it in until your device turns on/off. Then hold it there carefully, and press and hold the ACTIOn key and the reset button.
Works for me!
I have problem with power button. when push pwr button dont,t off pda, but when hold pwr then lights off.
Power is never shut off in PDAs, thats the way PDAs have been designed.
I have the same problem, he is not talking about a full power down. If you hit the power button quickly the phone does nothing. However if you hold the power button down for about 2-3 seconds the lcd light turns off as it should.
Because of this I have to wait 1 minute for the unit to suspend before putting it back in the holster.
Does anybody have any idea as to why this might be happening. Im not new at this so hard reset, soft reset.. new rom... new radio...turning up side down while chanting. It does not change......
It will do it right one or twice in a week.
Maybe somebody that understands the signal that the unit receives upon pressing the power button might be able to shed some light on this.... Again the button does seem to operate just not suspend when pressed normally (1 second or less)
I have done some more research and this seems to be a common problem for some with BAs but nobody has found out why. There must be some kind of common hardware fault.. Does the power button send only one signal or is it a multi signal device.
afbcamaro said:
I have the same problem, he is not talking about a full power down. If you hit the power button quickly the phone does nothing. However if you hold the power button down for about 2-3 seconds the lcd light turns off as it should.
Because of this I have to wait 1 minute for the unit to suspend before putting it back in the holster.
Does anybody have any idea as to why this might be happening. Im not new at this so hard reset, soft reset.. new rom... new radio...turning up side down while chanting. It does not change......
It will do it right one or twice in a week.
Maybe somebody that understands the signal that the unit receives upon pressing the power button might be able to shed some light on this.... Again the button does seem to operate just not suspend when pressed normally (1 second or less)
I have done some more research and this seems to be a common problem for some with BAs but nobody has found out why. There must be some kind of common hardware fault.. Does the power button send only one signal or is it a multi signal device.
Click to expand...
Click to collapse
Do you have a problem with turning on? First, we need to know whether it is hardware issue or not...
What you can do in the mean time with the turning off problem is by installing a poweroff app like shutdownme, psshutxp, etc etc...
Absolutely no problem with turning on from standby... Right now i just lock the phone before placing it back in the holster.
To make it clearer if you HOLD the power button down the backlight will turn off only. It will still show the display image and keys will still function (it dims)
Well, I had the same issue with the latest WM5 ROM. I thought I was too stupid to press the button, then I thought the button was broke, then I thought, I'll have to live with it.
Now that I have flashed to WM6, no problems at all! Never even came to my mind that this problem once existed. So I guess that some ROMs just have this particular bug?
Stefan
I have tried all the roms as well as 2003 and have the same issue in all of them. And im not alone.
Power off Problem
I'm in same condition.
Had the same problem when using WM2003 second Ed.
Now I've installed WM6 but nothing changed:
I cannot power-off/suspend but can turn off backlight if press and hold power button.
When in standby the button works fine to turn on the device.
Also, sometimes volume turns up continously with "noisy" beep ...
Anybody solved this problems?
Thanks,
Ruben
(WM 6 - 5.60.00 build 18125.0.4.2
radio 1.12.00 )
Power button has two modes:
1. Click mode: Click it once for a short duration. This turns off backlight and can be resumed by pressing it again or by pressing OK button
2. Press and Hold mode: Press and hold for few seconds and release. This mode will dim the backlight and no other button will bring it back. This is some kind of deep sleep in battery mode. To resume the original setting, press and hold Power button again for few more seconds.
(p.s.: I am not sure if this behavior is true for all the BA models)
April 1,
I know these modes...
It seems that "mode 1" doesn't work at all...
I would activate "Button Lock" (settings-->button--> Lock(tab)--> "lock all buttons except power button") to turn-off backlight and "lock all buttons except power button" but I cannnot...
You solved this problem?
I have had this issue of not being able to power off. One way I always got out of it was by clearing the registry hive. Unfortunately this brings the PDA back to the basic ROM. At this point the power button worked without any issues. Upon reloading the software the problem may come back. I believe the issue is related to some programs. I can't recall which program it was that seemed to cause the issue. One other thing I think that also worked was just entering the registry and getting back out and doing a hard reset.
I had the same problem with my 6600. the message button also didn't work. Believe it or not, to fix it. I banged the lower half (4-way area) on my desk a few times. Not hard enough to break the screen. But prolly hard enough to free what was prolly a sticky key. And now everything is working.
i am too
the same ...
when i press the power quickly , nothing happen
when i press the power for 2 sec. the backlight turns off
i tried every thing .... including formatting my BA
any one solve it ???
I have this same problem, my power button does`t work. i tried installing different roms but without any chance to fix it. maybe its an mechanic issue. i will change pwr button, i hope this work.
Look at one of my previous posts. I fixed it, twice, and other users have used the same metod to fix it. I think the problem is "hung bit" hardware related because you can also send it in for service, and they will change a chip, but i never had to.
Hey bit of a problem..
my power button only works intermittently. To turn the device on i need to press another hardware button and THEN the power button. If i just press the power button it wont turn on.
The power button works fine to turn it off.
I cant hard reset for soe reason (gps + ex + reset)..ive tried installing a new ROM but it hasnt fixed the issue.
Any ideas?
It is probably the hardware. any water damage? have you drop it before?
I looked for similar topic but couldn't find it,I can't use power button on my hd anymore,it got broken beacuse of pressing it very often during day to turn the screen on and off...I was wondering if there is an application to assign power button function to home key so when pressing it the screen turns off and on?
Hi, having the same problem, POWER BUTTON is defect/broken, it doesn't have a resistance when I push it in. I can still switch the device on and off, but I have to press the power button hard and the power button does not feel spring loaded any more.
Are there more people having this issue and is there anybody haveing it send for warranty repair already?
Mine is a German O2 device.
Thanks
hit007
Accidentally dropped my nook color and now it's acting weird. When I'm using it the menu that appears on power button press appears and sometime the device will randomly shut off soon after. I think something with the power button broke when the device was dropped. Is there any way to map the power button to one of the volume bottoms and then turn off the original power button?
BTW I'm using cm7 with the latest nightly build.
Thanks
No, the button is hard wired and not changeable. You might find a way to change for shut down purposes, but not start up.