Database Users

get cid information

Hi all:
how to get dopod M700's CID information? I just can bei able into bootloader mode

CID locked or not
imseasky said:
Hi all:
how to get dopod M700's CID information? I just can bei able into bootloader mode
Click to expand...
Click to collapse
I guess you want to know if your phone is CID locked?
Just try to upgrade with a complete_shipped_update_rom of the P3300 available from HTC.
If it does not give you any errors then your phone was CID unlocked.
Try at your own risk!
Regards,
mytrinity

imseasky said:
Hi all:
how to get dopod M700's CID information? I just can bei able into bootloader mode
Click to expand...
Click to collapse
If you want to know if your device is CID locked or not:
1. go into bootloader (RGB screen)
http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets
2. disable active sync connection
3. connect USB cable and start mtty console.
4. perform set 32 command in mtty console.
in a response you will see g_cKeyCardSecurityLevel = 00 or
g_cKeyCardSecurityLevel = FF
00 - stands for unlocked
FF - locked
rem: if you use USPL (USPL is installed on your device), then set 32 command will always report g_cKeyCardSecurityLevel = 00, although on a reality device remains locked. USPL just bypass CID check.
regards,

thx u!

fdp24 said:
If you want to know if your device is CID locked or not:
1. go into bootloader (RGB screen)
http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets
2. disable active sync connection
3. connect USB cable and start mtty console.
4. perform set 32 command in mtty console.
in a response you will see g_cKeyCardSecurityLevel = 00 or
g_cKeyCardSecurityLevel = FF
00 - stands for unlocked
FF - locked
rem: if you use USPL (USPL is installed on your device), then set 32 command will always report g_cKeyCardSecurityLevel = 00, although on a reality device remains locked. USPL just bypass CID check.
regards,
Click to expand...
Click to collapse
whats mtty console?? thanks

<snip> it's a console app...you run it on the PC, connect via usb and it sends commands directly to the bootloader...but you can mess things up if you don't know what your typing...

scrappydoo:
mtty is console, enables you to interact with device thru command interpreter implemented in SPL of the device.
it is a software.
don't be lazy next time and use search, it is designed specificaly for this..
regards,

Cmd>
Cmd>set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = FF
HTCE
how to cid unlock???

imseasky said:
Hi all:
how to get dopod M700's CID information? I just can bei able into bootloader mode
Click to expand...
Click to collapse
for get CID information use this program
http://www.androlib.com/android.application.org-tritonsoft-cidgetter-zjCAj.aspx
or search in googleMarket CID Getter

vasilii_htc said:
for get CID information use this program
http://www.androlib.com/android.application.org-tritonsoft-cidgetter-zjCAj.aspx
or search in googleMarket CID Getter
Click to expand...
Click to collapse
previously, I congratulate the new year to everyone in xdadevelopers ​ vasilii_htc yes you are correct, but the link to get the CID that you give it to a specially-based devices android...... thank you for its information ​

Orbit Stuck On Booloader

JUST recieved a orbit stuck in bootloader
The boot loader says
IPL 3.04.0001
SPL 3.04.0000
is there any way to unbrick this set
USPL is not working cuz its stuck in bootloader and cant conect with active sync
i have also tried sd card image but image is also not working
(flashing through sd card does'nt starts )
what it could be???

If I remember correctly, if you get a copy of the original ROM for your phone you can flash that from the bootloader. I'm not sure how to exactly though. I think you load the phone to the bootloader, then connect to the computer. Next I think you run the ROM update utility for the original ROM, this does'nt require activesync. I'm not 100% sure of this since I have'nt had to do it myself, but I found information in other posts on this forum. Run a search for Bootloader in the artemis section and you should find more information.

i have tried that too
but not working

I did this last week. I downloaded the WM6 update from the o2 xda website. I left the phone on the bootloader screen and rean the download from the PC. It re-installed the WM6 rom without activesync. You need your Serial number from off the phone.

Awais said:
i have tried that too
but not working
Click to expand...
Click to collapse
not flashing or not booting after flashing with original rom?
try another rom with same model id.
regards,

fdp24 said:
not flashing or not booting after flashing with original rom?
try another rom with same model id.
regards,
Click to expand...
Click to collapse
yes not flashig even i have tried from card
but its able to sync with the pc in bootloader mode (but not with active sync of course)
i have tried these roms
Arteimg.nbh (through card)
and these through windows
HTC_P3300_GER_3.13.407.1_4.1.13.44_02.94.90_Ship_R.exe
ARTEMIS_Black_Blue_v2.zip

please send error message and your device model id.
regards,

hi and sorry for answering late
i am actually away from office now and that set from the customer is in my office
i thought that invalid vender id error in the end of ruu update
i will check again and post screen shots

OK
here is the error i am facing
and when press the send button to hard reset
it says "format failed"

i have tried latest official wm6 from this link of o2.de
http://www.o2online.de/nw/assets/blobs/software/xdaorbit-windows-update.exe
this rom xdaorbit-windows-update.exe
and also this one from o2 uk
http://member.htc.com/ruudownload/O...r=http://www.my-xda.com/xdaOrbitSoftware.html
this rom
RUU_Artemis_O2_UK_3.4.206.2_4.1.13.28_02.67.90_Ship.exe
and got the same error "invalid update tool"
what it could be????
is there any special ruu (no id) fo r artemis ???

- try to flash device while in bootloader (there will be no activesync connection, but it is not a problem);
if this will not work either, try to flash from another PC;
also perform set 32 command from mtty console to see what is your model id.
regards,

i have tried on 3 different pc's
here is what i got after set 32
set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = FF
HTCE
Cmd>

and now i put wm5 o2 orbit image in the sd card and in mtty set 32
gives this
set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SD clock to 24MHz
***** user area size = 0x3C8C0000 Bytes
SDInit---
SDInit OK
g_cKeyCardSecurityLevel = FF
HTCE
Cmd>

in mtty:
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SD clock to 24MHz
***** user area size = 0x79E80000 Bytes
SDInit---
SDInit OK
g_cKeyCardSecurityLevel = 0
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
Cmd>getdevinfo
HTCSARTE10000àyqHTCE
Cmd>
look at your model id.
open nbh file with hexeditor, look for offset 00000040 for model id.
make sure model of device match with model in nbh. otherwise it will not flash.
have you tried to flash another device (same model id) with nbh file you have.
maybe you have corrupted file!!
regards,

OK I DID THAT
i find my id
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
RUURUN fail
HTCSF
Cmd>getdevinfo
HTCSARTE20000€zÁjHTCE
Cmd>
and now i am doing this rom
ftp://ftp.xda-developers.com/Uploads/Upload/Official XDA Orbit ROM UK TEST/
RUU_Artemis_O2_UK_1.25.206.1_02.67.90_Ship_R2.nbh
given by WolfDac
here
http://forum.xda-developers.com/showthread.php?p=1681205#post1681205
and he said its official orbit uk rom
but the rom upgrade utility in german
and this rom is also not working for me
my device info is this
Cmd>getdevinfo
HTCSARTE20000€zÁjHTCE
Cmd>
and in the offset 00000040 my rom (in hex) ARTE200
where is the model id in my mtty pasted data????

fdp24 said:
in mtty:
have you tried to flash another device (same model id) with nbh file you have.
maybe you have corrupted file!!
regards,
Click to expand...
Click to collapse
no i dont have any other orbit (yet) to check
i had purchased from customer
and he said its from uk
no, my file is 100% ok,,, i am sure cuz i download that nbh image from three different hostings three times, same size and same file
o2 provides xda orbit in how many countries ???
may b i should try some other files, instead of germany and uk
from where i can get other files ???
i am very thankful for your co-opertation

waiting for the answer

i was messed up
so i opened my orbit, and the board was perfectly fine (new), i opened in the confusion that it may be water damaged or some thing like that.
but my doubt is clear now, there is no hardware problem in this set, it is sure that i need a factory rom for this but still not able to find out that from which country O2 provided that set???......

i was saying about change of model id nbh file assuming that device is cid unlocked. if not it will not work, because if you made a change, you need to sing nbh file with htc certificate, otherwise it will not install.
you know your model id, search internet and install corresponding rom for arte200.
regards,

what exactly is my model id i have pasted details of mtty obove
would you please tell me that which rom i should try now???

O2 Orbit Struck at Bootloader - Help me please

Hi,
I bought an Orbit from ebay and found that I was cheated.
When I start the phone, I got the 4 coloured screen (Red, Green, Blue, White)
The screen reads
IPL 1.25.0001
SPL 1.25.0000
When I connect the phone via USB Cable to PC, i got the following
The bottom line says 'USB'
The top right corner says 'RUU'
I tried to flash the Original ROM using SDCard, But when when the screen ask to Pressdown the 'Volume' button, I press down the botton, but the screen goes back to the 'Bootloader screen'.
When I try to run the original 'ROM' using the 'ROM Update Utility', I got the 'Error 300' Invalid update Tool.
MTTy command output follows
set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = FF
HTCE
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
RUURUN fail
HTCSF
Cmd>getdevinfo
HTCSARTE20000€zÁjHTCE
Cmd>

Im assuming that if it enters bootloader, an detects USB and RUU then you should be able to flash a ROM to it. First I would try to flash USPL then try a cooked ROM.

Orbit Struck at bootloader
I got that problem same you.
Who can solve this ploblem?

fubofo said:
Im assuming that if it enters bootloader, an detects USB and RUU then you should be able to flash a ROM to it. First I would try to flash USPL then try a cooked ROM.
Click to expand...
Click to collapse
you can't flash USPL in a bootloader. haret needs to load patched spl while running in windows..
santhoshkumar:
it could be possible to fix your device, but device is physicaly required
regards,

fdp24 said:
you can't flash USPL in a bootloader. haret needs to load patched spl while running in windows..
santhoshkumar:
it could be possible to fix your device, but device is physicaly required
regards,
Click to expand...
Click to collapse
Hi,
Where to send and how much? Please send PM
Thanks
Santhoshkumar

Help me,please...
When I start the phone, I got the Bootloader mode.
The screen reads
IPL 1.25.0001
SPL 1.25.0000
When I connect the phone via USB Cable to PC, i got the following
The bottom line says 'USB'
The top right corner says 'RUU'
I tried to flash the Original ROM using SDCard, But got "SD FAT Update Failed!!!"What it's wrong?
When I try to run the original 'ROM' using the 'ROM Update Utility', I got the 'Error[226]:FLASH WRITE'What's happen on my XDA orbit?
Which way can unbricked my Orbit? Tell me please...

joke_drummer said:
When I start the phone, I got the Bootloader mode.
The screen reads
IPL 1.25.0001
SPL 1.25.0000
When I connect the phone via USB Cable to PC, i got the following
The bottom line says 'USB'
The top right corner says 'RUU'
I tried to flash the Original ROM using SDCard, But got "SD FAT Update Failed!!!"What it's wrong?
When I try to run the original 'ROM' using the 'ROM Update Utility', I got the 'Error[226]:FLASH WRITE'What's happen on my XDA orbit?
Which way can unbricked my Orbit? Tell me please...
Click to expand...
Click to collapse
Can't work out what you're trying to do - do you want to re-flash via:
a) bootloader, or
b) SD Card?
If it's bootloader, you'll already need to have [successfully] flashed with USPL, which, according to your SPL numbers above, you haven't.
Tends to suggest you're back to SD Card. To make this work, you need to copy a working nbh image to the root of your SD card. There are plenty here, but you might be well advised to start with one associated with your Carrier, to avoid SPL problems. Just take the .nbh file of your chioice and call it "arteimg.nbh" then place it in the root of your SD.
Soft-reset, and the device *should* find the .nbh file - a bit like a boot disk on a PC.
I'll be lurking all day - so can field ant questions you may have - I've done this tons...

if its O2 orbit UK i have WM6 and WM5 original nbh. PM me

Not working 2
When i tried to re-flash via SD Card i got "SD FAT Update Failed".I used "ARTEIMG.nbh" WM5 UK Official ROM.That i copied nbh image file to the root of my SD Card. What's it wrong?
And when i tried to re-flash via Bootloader.I got ERROR[226]:FLASH WRITEat 5%.Which way to unbricked it?

Try to format Ur card to FAT32. erase everything except ARTEIMG.nbh, dont know if Arte supports DOC formating maybe thats the last resort (except service)

phsnake said:
Try to format Ur card to FAT32. erase everything except ARTEIMG.nbh, dont know if Arte supports DOC formating maybe thats the last resort (except service)
Click to expand...
Click to collapse
ัำyep,It's formatted to FAT32.But i don't understand DOC format.
SD FAT Update Failed again what does it mean?

sd card fat update failed means smth is wrong. try o2ship UK WM6[/U] extract thru winrar, rename copy to card, U may try to flash it directly (if U have UK o2)
DOC formating smth like creating new fat on device....

I'm so sorry.For my stupid.What's DOC format and smth? Please explain me.
And this for my error.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Please,help me and help my orbit.I miss it so much...

O2 XDA Orbit Unable to Flash - All Attempts Failed

Hello Everyone,
After going through the forum for two days, and using almost all the information available, I felt the utmost need to start this thread.
The Phone
I've O2 XDA Orbit, on the back it says HTC Innovation, and has serial no. with HTxxxxxx. IMEI Analysis says phone is from UK.
Current Status of Phone
When I start the phone, I see green display with IPL 1.25.0001 and SPL 1.25.0000, and the phone gets stuck. I tried hard reset, and got the message, Format FAT Partition, Format is Failed. Then I can see O2 Welcome screen with IPL and SPL on the top.
Attempts to Flash the ROM
Since my priority is to get the phone working properly, I first downloaded the Original Flash from HTC's Website, the file name being RUU_Artemis_O2_UK_3.4.206.2_4.1.13.50_03.06.90_Ship.exe. I tried flashing and got the Error 300:Invalid Update Tool. The RUU Version is 3.6.3.5. I downloaded various ROM's and tried all of them, but ended with the same Error 300. I tried RUU Version, 2.0.0.1, 2.5.2, 3.0.3.5, 3.3.3.3. I've been unable to get a version better than 3.6.3.5.
I've also marked that whenever I attempt to flash the ROM by going in bootloader mode, the phone stops responding. It means after getting Error 300, I restart the phone only then I get the same error, else I get Connection Error .
Specifics in RUU
At the Screen Indicating Current Information about your PDA Phone, no Image Version is displayed.
At Rom Verification Screen, From: and Image Version: remain blank, To: also remains blank, but the ROM in RUU's folder's image version is displayed.
SD Card Flashing
Finally I tried SD Card Flashing, by renaming the Original ROM to Arteimg.nbh. Unfortunately the phone said Invalid Certificate. This happened with all the ROMs, which range from CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE, Hard SPL, Artemis_USPL, OrbitO2UKoriginalROMwithWM5, etc..
I'm unable to understand what am I doing wrong, and why exactly the original ROM not getting uploaded.
Any help would mean a lot.
wbr
Disillusioned
P.S. - Active Sync never goes GREEN as phone never gets started.

Possible Problem
Any Suggestions for the possible problem?
Or
Can someone post me a link to a higher version of ROM Update Utility.
wbr
Sonny
P.S. - I feel this could also be a hardware problem.

MTTY
Last night I tried mtty 1.43
Mtty didn't even accept the password "BsaD5SeoA".
Cmd>password BsaD5SeoA
Invalid password.
HTCSFFHTCE
Cmd>
Here is the output after using Send 32 command.
Cmd>set 32
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = FF
HTCE
Cmd>
Is there anyway this device can be fixed.

lsn try this.
when your mobile is off press the record button and the power botton while on your SD the original orbit rom.
this flashed my device even while my orbit was completely dead .
and the flashing was alittle different than usual (three phases and more time).
don't know if this works for you... but why don'y you try it

ROM Check
Thanks for the check in there brother.
I have tried ROM from HTC's web site, which happens to be the Original ROM, and have signed nbh file. But all in vain.
Then I've downloaded various ROMs from xda's ftp server, but none of them worked for me.
I'm unable to understand what to do.

sorry mate.. i previously i said camera botton.. it's wronge.. it's the record botton
i still got confused sometimes with the botton cuz i had an i-mate jam

I've tried almost all the ROMs available on the internet, but none of them worked for this phone.
How can I fix this phone?

have u fixed it?

Conclusion :
The phone have had hardware issues. The Flash IC was bad (cracked), thats the only reason the phone was not getting flashed.
Thnx
Sonny

ok, if i open my artemis could i see this "part" to know if thats wrong with mine to? (i have opened it before) and is it possible to change it by ur self ?

If you ain't a professional then don't get into changing the Flash "IC".
I would say, try blowing the Flash IC with hair dryer and see what happens.
Moreover, when you get into bootloader mode, you should see SPL IPL and GSM. If you don't see all the three, then I suppose it suggest an hardware issue.
In my phone G/GSM was missing, when I blowed the IC, G popped up while booting, but then it vanished again.
Hope it helps.
Sonny

MTTY Not Accepting Password Problem
After password command you need to give two blank space and then the password for the password to get right.
Cmd>password BsaD5SeoA
Cmd>password(two blank space)BsaD5SeoA
wbr
Sonny

far from profesional but i do have a friend thats closerto that than me.......so does any know how i could localise the part? mabe a pic of it? my artemis is no use for me now so it cant be worse

Blow the phone's circuit board with a hair dryer. If things may have any possibility of working they will, there ain't anything to loose though.
Blow it real hard!!

Elf 0100 RUU loader problem :((((

Hi,
For the past 2 days I was searching for a solution on the entire xda-developers forum but none worked for me.
My sister recived a htc elf 0100 and the language was in spain. I wanted to change it to english and I tryed to update the ipl/spl. I don't know exactly what I did but the 3 color RUU screen appeared, and it does not dissapear.
Even if I remove the battery and after I set it back again, the same screen appears, it does not enter in windows.
It says :
IPL: 2.21.0002 and SP 2.26.0000
and in the bottom left : USB
How can I solve this ? If I try to install a ROM (I tryed 10 different ROM's at least) it always says error [270] .
I searched the error and tryed every solution, but it does not work.
What should I do ? Also please tell me a good english rom.
I hope someone can help, becouse it's my sister's telephone and she will really kill me
Thank you

ELF RUU 0100 problem
OK! No need to be nervous.
Tru first to install new IPL and SPL if you don't have it right ROM. They are much smaller and take less time. Beter ofcourse is to find the right file.
Try to find this one - RUU_Elf_HTC_WWE_1.11.405.1B_4.1.13.42_02.93.90 _Ship.exe My ELF was same model with same problem utill I find this file.
Is good point to try look for viles with IPL/SPL versions 1.11 until 1.19.
Some links about same or look like files:
http://rapidlibrary.com/download_fi...+WWE+1.11.405.1B+4.1.13.42+02.93.90+Ship+.exe
and http://rapidlibrary.com/download_fi...+RUS+1.15.411.1B+4.1.13.42+02.93.90+Ship+.exe
After you succeed to upload some ROM make CID unlock and upgrade IPL/SPL to 3.07 (thanks to cmonex). If this not help please look for Gold Card unbricker method. This works for me Thanks to dsixda. Look at the forum, here I find a lot of things and explanations.

otherwise try to use MTTY file search google....
and folow these steps to reset your device
This is the tricolor RUU boot-loader:
http://www.ismodel.net/forum/richedit/upload/2kcf486c647d.jpg
1) Disable USB in your ActiveSync program.
http://www.ismodel.net/forum/richedit/upload/2k08f7e6a5b2.jpg
2) Download and run the mtty.exe (http://andrewloh.com/mtty.exe)
3) Change the port to "USB" & Flow control to "RTS/CTS"
http://www.ismodel.net/forum/richedit/upload/2k66e8168767.jpg
4) Press <Enter> once and you should able to see "Cmd>"
5) Issue the following command:
http://www.ismodel.net/forum/richedit/upload/2k3905d74812.jpg
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDInit: ACMD41 wait for power up bit timeout
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDInit - SD ver2.00
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Card status error in response. MMC_STAT = 4000
SDInit: ACMD41 wait for power up bit timeout
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST
Cmd>ruurun 0
Cmd>ResetDevice

Hello guys, thank you for the quick replyes but I didn't manage to solve the problem.
malintzin ->
When I tryed to install the WWE exe (from your post) it stopped at 3% and it sayed invalid number (error 244).
The same thing gappened to the RUS version
marco3key ->
I also tryed the mtty yesterday, but still no luck. When I am writing what you posted, nothing happens.
Any other ideeas ? (
Thanx
********EDIT1
I noticed that I was doing something wrong with mtty , I coyped and pasted in sted of tyiping myself. So I typed :
password BsaD5SeoA , after that the white screen appears with 0% loading.
when I type ruurun 0 nothing happens and than when I type ResetDevice the device gets a reset but reenters the tri color boot screen
*******EDIT2
I noticed that after I write password, I don't recieve the same text as in the image. Here is what is showes in mtty :
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
SDCmd55 Command response time-out. MMC_STAT = 80
CMD55 failed
g_cKeyCardSecurityLevel = FF
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
HTCST

IPL/SPL
Good start - I pass all this steps as well
So let I said again:
"Try first to install new different IPL and SPL if you don't have it right ROM. They are much smaller and take less time."
And the procedure is same as for normal ROM.

Hi,
I tryed to install every IPL and SPL from here :
http://forum.xda-developers.com/showthread.php?t=408637
None worked. Whenever I tryed to install one, the loading went to 100% (sometimes not) and after that, the phone reset from the tri color screen (and imediatly restarted to the same screen) and the PC updater sayed ERROR 270.
I don't know what to do
*********EDIT
If I try to install ELF_USPL-v1.zip, 2 .... and I double click on elf-uspl.exe it says that the active sync should be connected. I can't connect to active sync if I am in the 3 color screen. So how can I install elf_uspl ? Again, if I only try to install from RUU the phone resets and the error 270 appears
**********
Please try to help me, I noticed some people waited even 2 months to fix their phones, I don't want to do the same . Thanx

Any luck trying to fix the 270 error?
I've spent about 4 hours now trying to flash my Elf. It it stuck on Smart Mobility bootup screen. Worst part is all I did was BACKUP my ROM in case one day I'd have to use it again... After the first reboot following the backup, I find myself in need of my original ROM... and can't even use it.
I've tried mtty.exe, flashing to different SPLs, from Vista, from XP, from the microSD card, with/without USB connections enabled...
I'm at my wit's end.
If anyone out there can help, please, I'd greatly appreciate it.

This ROM may fix.
Make sure u are in tri color mode and run this.
http://www.dopodasia.com/download/RUU_Wizard_2211301_22113102_021911_DOP_ASIA_WWE_Ship.exe
All the best.
Yash

yashkum said:
This ROM may fix.
Make sure u are in tri color mode and run this.
http://www.dopodasia.com/download/RUU_Wizard_2211301_22113102_021911_DOP_ASIA_WWE_Ship.exe
All the best.
Yash
Click to expand...
Click to collapse
Link dont work.