Database Users

Stuck in bootloader after failed flash

Hi, got some problems with one of my employes Herald (not simlocked or anything).
It ended up on my desk after complaints about it rebooting by itself every minute or so. I figured I could sort it out by upgrading to wm6. Wen to HTCs website and downloaded the official RUU (HTC_P4350_SVE_4.17.413.2_4.1.13.44_02.94.90_Ship.exe). Everything went along fine and I left it upgrading on my desk and went for lunch.
When I got back it said that the update had failed and I followed the recover function but without success.
Now Im stuck in bootloader mode, and when I try to update it again the current image version is listed as blank and I get to about 1-2 percent before it shuts down and gives "ERROR [244]: INVALID MODEL ID".
Any suggestions on what to do?

Further information...
IPL 4.17.0001
SPL 4.17.0000
When i do a hard reset, after it says format complete it boots up and freezes with a green gradient across the screen.

You can try using USPL or HARDSPL to flash.
The USPL will get around CID locks
This is from ivan's A Herald's Guide to Flashing Aserg, USPL and HARD-SPL - xda-developers
II. How do I flash an NBH file?
Warning: To use the NBH ways, you MUST have a SPL of 4.0 or higher. If you have a lower SPL, you WILL brick your phone.
a. USPL
Step 1. Download Herald-USPL-Beta3.
Step 2. UnZIP the file into a folder on your Desktop. Let's call it "MyFirstROM" for simplicity's sake. Notice that there is a folder called RUU within this folder now. Keep that in mind.
Step 3. Download your NBH file and unZIP or unRAR it into that RUU folder. Make sure that that NBH file ends up in the RUU folder, not within a folder inside the RUU folder.
Step 4. Place your phone into flightmode.
Step 5. Go back to the MyFirstROM folder and then run USPL.exe
Step 6. Follow the directions on the screen. EXACTLY.
Your screen on your cell phone will go white around the 75% part of the "second step" now.
ActiveSync will LOOSE its connection.
Step 7. One step 3 on that black window, the RUU flasher will pop up. Just follow the steps.
That's it. Welcome to the flasher's world.

Thanks for the reply,
First, I cant get activesync to find the phone, only evidence of contact in between the phone and PC is that its listed as [Windows CE USB Devices+PocketPC USB Sync] in device manager. I tried to uspl flash with ASERG.8, and it stops at "STEP 1/3...."
I downloaded mtty to see if it could connect, and it did.
Any further suggestions on what might work!

uninstall..reset.. clean install would probably get activesync to work w the phone..

Reinstalled activesync without any change. And soft/hard reseted everything…
Tried to flash via sd as per instructions in another thread, got to "checking SD contents" and then straight to triple-color bootloader.
Help me please! ;D

Cant help getting the feeling that Im completely screwed...
Cant get activesync to recognize it, only way to get it to light up is via bootloader (camera + reset button), everything ive tried to flash it with hangs almost instantly.
As a complete novice my guess is that the current rom is corrupted and I badly need advice on how to go on. The sd-flash seems quite logical but I cant get it to work. Ive tried to overwrite my sd with 00-values in winhex and then placing the original ruu [HERAIMG.nbh] (through windows, is there a way to write data with winhex?) on the card without any success.
Any suggestions on what to try is much appreciated.

Sounds like the SPL got corrupted or partially written only... sorry. Repair center time. You can also placing your Stock RUU's nbh file into your SD card and renaming it to... umm.. I forget... and then flashing FROM the phone.

facdemol said:
You can't simply place the rom file to the card and hope the device will read it in this way. In my time working for pda service, we used WINHex to format the card (to RAW-unformatted) and then we wrote the rom file in RAW format to the card. Your card looks like an endless stream of hexazecimal values. Only winhex recognises this format, if you insert the card to the computer, it will simply ask you to format it. After inserting this card into the pda, it will start the upgrade . The order of this operation was, as I remember, to fill the card with 0000 values (there is an option in WINHex, a kind of format) then write the rom file to the card in RAW mode. Then insert the card to the device.
Click to expand...
Click to collapse
Thanks for the reply, before giving up and sending it in for repair I would like to give the sd-flash a proper try... So far Ive managed to format the card with winhex but I cant really figure out how to write to the card in raw format. Could anyone point me in the right direction?

i managed to do the steps said above ... formated the card in RAW format etc but still the phone won't turn on ... it will only stay in bootloader ...

diabolic53 said:
i managed to do the steps said above ... formated the card in RAW format etc but still the phone won't turn on ... it will only stay in bootloader ...
Click to expand...
Click to collapse
Care to enlighten me on how you did that?

I've been reading a lot lately.. I wonder if the phones are savageble... something about flashing but bypassing the radio check... Also, the universal has an RUU that bypasses any checks before it flashes... this would be great for us to have... I'm asking around...

g4rwin said:
Care to enlighten me on how you did that?
Click to expand...
Click to collapse
whell i opened the mem card with winhex filled all the blocks with 00 and then i opened the nbf file also with winhex and copied the content in hex format on to the card ....but still no success ..

ivanmmj said:
I've been reading a lot lately.. I wonder if the phones are savageble... something about flashing but bypassing the radio check... Also, the universal has an RUU that bypasses any checks before it flashes... this would be great for us to have... I'm asking around...
Click to expand...
Click to collapse
if you find it please tell us about it cos a lot of phones are getting bricked ...

If I'm correct, you told us a few post above thisone you placed your SD card with the imghera.nbh and got "checking sd conents" and then it went to bootloader.
As far as i can recall you need to get your Herald into bootloader first and then place your SD card with the IMGHERA.nbh file on it. Then it should start reading the image from, your SD card.
Judging from your first post you haven't been using the asigned RUU from the HTC website if this was your first rom flash to WM6 and you got a vendor error. Try to convert and use that one when you flash from sd card.

jappo01 said:
If I'm correct, you told us a few post above thisone you placed your SD card with the imghera.nbh and got "checking sd conents" and then it went to bootloader.
As far as i can recall you need to get your Herald into bootloader first and then place your SD card with the IMGHERA.nbh file on it. Then it should start reading the image from, your SD card.
Click to expand...
Click to collapse
Ive tried all possible ways, if I pop the sd card in while already in bootloader, nothing happens at all.
jappo01 said:
Judging from your first post you haven't been using the asigned RUU from the HTC website if this was your first rom flash to WM6 and you got a vendor error. Try to convert and use that one when you flash from sd card.
Click to expand...
Click to collapse
Ive been trying to flash with the WM6 RUU I downloaded from HTC's site (the one that bricked it) since that is the only local (swedish) and official one I could find. Have I misinterpreted it all and the only thing that could do the trick for me is WM5.1?
Ive also been trying to contact the HTC service dept for over a weeks time ending up in a deadend overfilled voicemailbox - meanwhile my warrantyperiod ran out... Any suggestion on what to do?

duprade said:
You can try using USPL or HARDSPL to flash.
The USPL will get around CID locks
This is from ivan's A Herald's Guide to Flashing Aserg, USPL and HARD-SPL - xda-developers
II. How do I flash an NBH file?
Warning: To use the NBH ways, you MUST have a SPL of 4.0 or higher. If you have a lower SPL, you WILL brick your phone.
a. USPL
Step 1. Download Herald-USPL-Beta3.
Step 2. UnZIP the file into a folder on your Desktop. Let's call it "MyFirstROM" for simplicity's sake. Notice that there is a folder called RUU within this folder now. Keep that in mind.
Step 3. Download your NBH file and unZIP or unRAR it into that RUU folder. Make sure that that NBH file ends up in the RUU folder, not within a folder inside the RUU folder.
Step 4. Place your phone into flightmode.
Step 5. Go back to the MyFirstROM folder and then run USPL.exe
Step 6. Follow the directions on the screen. EXACTLY.
Your screen on your cell phone will go white around the 75% part of the "second step" now.
ActiveSync will LOOSE its connection.
Step 7. One step 3 on that black window, the RUU flasher will pop up. Just follow the steps.
That's it. Welcome to the flasher's world.
Click to expand...
Click to collapse
Hi I try tu patch IPL/SPL with hard spl but with error, now my herald stuck in boot mode. IPL/SPL 1.09.0001. He probbably is from some russia operator (rusian diacritics on keyboard).
How can I try to make him alive?

US HD2 error 262 on vista help plz

i just recently got a new hd2 wich run 2.13 rom software and im haveing trouble getting it downgraded so i can put hspl on it. I know this has bean mentioned before and looked and tried everything i found abot it. My dads pc is a 32bit vista home edition can every time i load the downgrade it goes all the way into the set up and then gets stuck at 0% and then gives me a 262 error in like 5 mins. I know its a comunication error andi have tried every usb port on the pc. I am getting a clear sync and have no problems getting stuck on the boot screen. I just halft to reset everytime when it says it wont load. I have tried forceing it threw the boot menu but nothing works. The phone runs just fine still and i even did a hard reset to see if that would help.
Plz if somebody can help me i would be verry greatful and i am even willing to donate if i can get the mods for the phone up and running.
Plz respond as soon as possible.

at this stage it doesn't matter that the pc doesn't work...... because you should be flashing the downgrade from sd card anyway.

ok well i tried it once and it just went to a white loading screen and did nothing else. all i did was put the nbh in the sd card so if i messed up mind helping me out.

ok so i just tried exactly what your link told me and it wont go past the white loading screen. do i just had a bad stock rom or what?

did you rename the nbh to leoimg.nbh?

yes i did change and i still just cant seem to get it to go threw

you using the stock 16gb card? loads of posts say that card doesn't work. try an 8 or better yet a 2gb

i have tried i 1,2,and 4 gig and nothing works.

what rom are you downgrading it with?
When you downloaded the rom, did it come as an .exe or did it come as an .nbh file and customruu.exe together? Because if it DID then that wont work, it must be the .exe version.
I recommend the 2.10.0 from the thread
[ROM]Leo 1.5 T-MOBILE Test & Stock ROMS
Have you extracted the ruu_signed.nbh correctly? (you didnt just rename the .exe to leoimg.nbh did you?)
ALso try formatting your sd card, FAT32, not FAT, and for best results do a propper format, not a 'quick' format.

i have done a propper format and its on fat32. i have also extracted the nbh file with 7zip i did not just rename it and i got the rom from a thread that had all the old os versions on this site

killer666666 said:
i have done a propper format and its on fat32. i have also extracted the nbh file with 7zip i did not just rename it and i got the rom from a thread that had all the old os versions on this site
Click to expand...
Click to collapse
assuming you mean THIS thread,, only the ones in that thread that come as an exe will work, the others will need hspl.

[Q] How to use a Goldcard

Oke guys here's my queston.
First look at:
http://forum.xda-developers.com/showthread.php?t=939763&page=3
My radio is probably bricked, so now i'm trying to use a goldcard:
I managed to get the CID of my SD card.
Reversed the CID of the 2 Gb is: 009b000a6daf00804732305553445303
With a little help of this forum i now have a goldcard and put an original LEOIMG on the goldcard.
Still no solution, the bootscreen flashes off/on 1 time and then returned into bootscreen. No attempt of flashing seen. What went wrong??
Thanks in advance!

first the obvious questions, (quite often its somethign dead simple) ,
you extracted ruu_signed.nbh and didnt just rename the whole .exe to .nbh?
How did you write the .img to the card? ? you
How did you get the CID?
let me have the two CIDS (dont reverse them or anything, just as you got them) and an email address and ill make you an image for each disk, that way you have three to try.
Magazijn said:
Still no solution, the bootscreen flashes off/on 1 time and then returned into bootscreen. No attempt of flashing seen.
Click to expand...
Click to collapse
on a normal sd card, this usually indicates either wrong stock rom being used (sure the rom you are using is for your region AND carrier?((if locked)), or an sd card that isn't set up right (freshly format it, FAT32 )
It might point to the goldcard image being wrong, or incorrectly written to the card.

I extracted the original HTC HD2 dutch rom, took of the ruu_signed.nbh, copied it to the goldcard en renamed it to LEOIMG.nbh
I got the CID by using a working adroid phone together with the tutorial from "theunlocker.com" (sdk/adb-app en hex-app)
The 2 onreversed CID's are:
1gb
035344535530314780606ca6f10079a6
2gb
03534453553032478000af6d0a009b8e
emailaddress: [email protected]
thanks!

Hey Magazijn if your problem is not a hardware issue then you have the right guy working with you now. Samsamuel will have you up and running again I am sure of it. Just remember though if you are using USB to flash and not SD card then always put your HD2 into bootloader and wait for the USB tben flash this is a trusted method. And don't forget to click Samsamuel's thanks button when he gets you going. Peace.

heh, cheerleader fees in the post.
@OP sorry for the delay, theres a step by step to double check you are writing teh image correctly HERE

Thanks for the quick solution samsamuel, but still the same problem.
After Boot the screen builds up again in boot and that's it.
So i think it's an hardware radioproblem with can't be fixed.
Should a hardware repair help me out?
Last question i used original dutch LEOIMG (winmo 6.5), can i use another (android of winmo) rom?
If yes, which would you prefer.
Again thank for your help, i appreciate it.

hmm, not sure what to suggest. As i said b4, a brief 'loading' then back to bootloader usually indicates the wrong rom. Are you sure your phone is an unbranded dutch phone? did you download that rom with your serial number from the htc website? (it will only let you download correct roms if you use serial)
This shouldnt matter if the goldcard is working, but if you KNOW its the correct rom, it can be discounted as the cause.

[Q] How to sync when in white screen error?

Hi Guys,
I'm kinda stuck here, hope you'll be able to help:
Situation is as follows:
I have an HTC Leo, and after 2 months of usage - got the white screen:
1. Tried soft reset - no good
2. Tried hard reset - no good
3. Cannot sync to PC with ActiveSync - does not detect the device
4. Can go to boot mode, but only with voulme down+soft reset button
5. Cannot sync in boot mode as well - there appears to be a "USB" writing at the bottom, (white line on boot mode) though ActiveSync does not detect via usb?
6. Tried to install HSPL2 - starts to install, never finishes, proggress bar goes up and down forever (on PC) - I believe device needs to be synced before installing?
7. Device is enabled in the device manager, though cannot explore - thus no access to SD card
8. Here we go, I seem to do something wrong, PLEASE HELP, I payed for the device about 400E in my country, stock warranty is not an option
9. HEEEEEEEEEELP
10. Thanks!!!

Try flashing the stock ROM for your HD2 via SD card. If you have a T-Mobile HD2 then go to T-Mobile.com to download the ROM you will have to enter the IzmEI number from under your battery to download it. If you have a international HD2 go to HTC.com and enter your serial number that is under your battery to getca list of ROMs you can download and install on your HD2. If the ROM is a .exe you will have to right click it and renamecthe file .zip to view the contents. After that follow the instructions in the thread linked below to flash the ROM.
http://forum.xda-developers.com/showthread.php?t=681317

[Q] Thanks
Hi, thanks for the info,
When I go to HTC homepage, i find "Rom Upgrades" - is that the same as the ROM itself?
Sorry if the q is dum ,I'm completely new in this
And also - does the card have to be empty (only ROM in) so that the phone boots it?
Thanks again

yasho1984 said:
Hi, thanks for the info,
When I go to HTC homepage, i find "Rom Upgrades" - is that the same as the ROM itself?
Sorry if the q is dum ,I'm completely new in this
Click to expand...
Click to collapse
Yeah that is what you are looking for. The ROM upgrades is the most recent official ROMs out for the HD2. Just make sure you use your serial number to make sure you get a ROM that is for your HD2 or you will not be able to flash it unless you get HSPL on your HD2. Also make sure the HTC site you are on is for your part of the world, your country or the country the HD2 originated from.

[Q] Hi again, last q
When I Explore the contents of the rom I see numerous files, and reading the instructions you linked tells me to rename an image. The ROM is an exe, so I renamed it to zip , explored and currently I see only one .nbh file:
RUU_signed.nbh
Should I rename this one to LEOIMG.nbh and copy this file only to SD card? Or rename and leave there, take the whole exe and put it into the SD Card?
Would that be sufficient to run the ROM in bootload?
Thanks again brother, you're a lifesaver

yasho1984 said:
When I Explore the contents of the rom I see numerous files, and reading the instructions you linked tells me to rename an image. The ROM is an exe, so I renamed it to zip , explored and currently I see only one .nbh file:
RUU_signed.nbh
Should I rename this one to LEOIMG.nbh and copy this file only to SD card? Or rename and leave there, take the whole exe and put it into the SD Card?
Would that be sufficient to run the ROM in bootload?
Thanks again brother, you're a lifesaver
Click to expand...
Click to collapse
Just take and copy the RUU_signed.nbh file make a copy ofcthe file and past it to your desktop and then rename it to LEOIMG.nbh then copy that file to the root of your SD card. All you have to have is the .nbh file but it has to be named LEOIMG.nbh.
You can also flash a radio, splash screen, and MAGLDR this way if need be. But you would still have to flash CWM via custom RUU via USB if you installed MAGLDR.

[HIHI]
Great - now "Radio fail" - update terminated... any ideas?
Exact error description:
00018003
LEOIMG.nbh - Fail
RADIO - Fail
Update Terminate
UPDATE FAIL
and this is an official HTC ROM?!?

yasho1984 said:
[HIHI]
Great - now "Radio fail" - update terminated... any ideas?
Exact error description:
00018003
LEOIMG.nbh - Fail
RADIO - Fail
Update Terminate
UPDATE FAIL
and this is an official HTC ROM?!?
Click to expand...
Click to collapse
Sorry I had to get some sleep, anyway I suggest you first make a backup copy of your SD card and then reformat your SD card using the Panosonic Mick SD card formatting software, just Google it you will find it. Do a full wipe of hour cardcand format it using Fat 32. Then copy the LEOIMB.nbh to your card and try it again. Also try to use a card no bigger than a 8GB as bigger SD cards are prone to give people problems when flashing via SD card. Note I did not say they will notcflash a ROM, bit they sometimes give people trouble.
Also I forgot to tell you this morning that if your HD2 says USB in the white bar of bootloader and it also says HTC USB sync in the device manager in the control panel of your computer, then you have a Sync connection to your computer but you can not use this connection for anything bit to flash different software to your HD2.

[Q] Hi Buddy, 10x for staying so long :)
Sorry brother,
I really appreciate your help so far.
Same Sh*t - even after FAT 32 format
When tried to upgrade with the official HTC ROM - "RUU_signed...." (not via SD) HTC boot screen appeared, but after 1% said : Image corrupted". It coud be that the stock rom sucks big time. May be try with some Artemis?

yasho1984 said:
Sorry brother,
I really appreciate your help so far.
Same Sh*t - even after FAT 32 format
When tried to upgrade with the official HTC ROM - "RUU_signed...." (not via SD) HTC boot screen appeared, but after 1% said : Image corrupted". It coud be that the stock rom sucks big time. May be try with some Artemis?
Click to expand...
Click to collapse
Yeah maybe you got a bad download of the ROM. If that was the only official ROM you could down load. I would try to download it againcand delete the first copy you downloaded, or I would flash HSPL. to my HD2 and then try to flash the stock ROM are a custom ROM. Custom ROMs are better than stock ROMs anyway. Just remember though if you have a warranty and you need to send your HD2 in for warranty work or exchange you need to revert your HD2 back to complete stock. This means ROM, radio, and SPL.

Think I Bricked some Help!

ok hey i tried putting a stock tom but i have a tmobie us hd2 and i tried putting some other language on it

.. and now it doesnt turn on, screen stays black and your pc asks for qualcomm drivers?
its bricked. the radio in non tmous stock roms bricks tmous hd2's.
or is it something else? your post is pretty empty of facts.

well it says nothing on my computer and it just won't respond

What's wrong with your phone?... what is your main goal that you want to accomplish with your phone???????
Sent from my LG-P999 using XDA App

its bricked.. look up jtag..
Your gonna have to do some work to get it going again.. I just did the same to my phone flashing a radio.. so i'm going to try to get something going. . If anyone has any suggestions let us know please.

it asks for qualcom drivers

yes, it will, look at the other radio brick threads, that's one of the tell-tale symptoms. but there aren't any drivers. (Yes, there is a 'qualcomm drivers' thread somewhere, but they don't install into windows, no one is sure what they do.)
That's the raw hardware looking for the qualcomm equivalent of JTAG. That's what shows up when there is no valid bootloader to start.

Have you tried flashing leoimg.nbh directly from SD card without PC ?
if no the steps are:
Find stock rom (or custom) and open the executable updater with winrar.
Extract the .nbh file from there (should be the largest file in the archive)
Rename it to leoimg.nbh
Copy it to the sd card with a card reader.
Insert card, start prone and keep pressed the "down volume" and the "Call reject"
button at the same time.
This should get you to the file flash stage there keep pressed or click the reject button to flash the file.
Might not work if card is partitioned.

anderwalentzack said:
Might not work if card is partitioned.
Click to expand...
Click to collapse
more to the point it won't work because it doesn't turn on so no bootloader available to start the flash. Its a tmous hd2 meets a non tmous radio, the only fix is jtag.