Related
:?
I have just purchased a dopod 838. While I enjoy it very much, I do have one problem I don't seem to be able to solve. The problem is as follows: my device finds and connects to my Wi-Fi net, it indicates that the signal is good (and the net is an open one, no need for any password), but even though I am connected, I can not browse the Internet or send or receive e-mails. I tried to find answers in the user guide, but all I find there are generalities. I guess it has something to do with the settings on my device, but it is really frustrating, as the main reason I switched to the 838 modal is the Wi-Fi. I think the problem may be connected to the Network Adapters. When I check the Network Adapters I see the following list:
PPTP NDISWAN Minipot
L2TP NDISWAN Minipot
AsycMac NDISWAN Minipot
Virtual Ethernet Intermediate Minipot
Remote-NDIS Host
NE2000 Compatible Ethernet Driver
SDIO WLAN Wireless Adaptor
The only one that is indicating the IP Address is the SDIO WLAN Wireless Adaptor, but is it the one to use out of the list? And if so, I do I do that? How do I set it to be the default adaptor?
Please help...
Thanks
Benny
I only do the setup one time for my friend. Hope that can help.
If the network hadn't any protect, you can just choice this on the screen when this had been found. It don't need any setup for a unprotected network.
If the network is protected, "password / soid / encrypt". You need to setup a network card, setting > connection > network card , with all the details before you can use the network.
No success
I have many adapters, it seems to me that the only one that is the correct one is the SDIO, but I can not make it the default one.
Internet access through Wi-Fi
If you've created a wireless network between you PC and your device, you need to 'share' your internet access on your PC. Also if you have a Firewall you need to enble that too, for mine it was the generic sub-program 'svchost'. Hope this helps.
no need to set the SDIO Wireless Lan Adaptor to default. That list is just a list and has nothing to do with privilege.
i think the problem is that your Wirelan has some restrictions to access,eg. MAC address. So,ask your network administrator for help ;-)
I have an iMate Jasjar.
WiFi works fine for AvantGo updates and Weather panel updates but Pocket IE and Terminal Server Client refuse to use existing WiFi link! :x
PIE always uses GPRS and if I flight-mode my radio, it simply fails to connect complaining about no GPRS connection! :evil:
Solution:
I installed Opera Browser Beta for PPC. It works over WiFi no problems.
My trial period is nearly up so they'll get some of my money. :wink:
Has anyone had any success with L2TP/IPSec VPNs and Windows Mobile 5 or 6? I have no problems with getting PPTP to work but have NEVER had any success with L2TP/IPSec. I have valid Client & Server Certificates but I have never been able to get a connection; in fact the HTC Wizard I have never even attempts to make a connection (I have a sniffer on the Ethernet port my Wireless AP is connected to). I have tried using Certificates & Pre-Shared Keys but the results are the same - The Wizard never attempts to connect, with PPTP it works every time.
The Server I am using is a Windows 2003 RRAS server and I have verified with a Windows XP Client that L2TP/IPSec works.
I have asked the question before but have not had any helpful replies. I would be grateful if anyone who has set this up successfully can let me know and maybe give me a run-down of the steps you used. I am not interested in any 3rd party VPN clients, it must be the built-in one.
Thanks
Andy
Hi
Yes I have had the same issue with both the wizard and now hermes tried wm5 and wm6. I think it maybe related to NAT-T translation as am unsure from my reading weather MS supports NAT-T on the mobile end. If data session is being NATed by your provider then this may be the cause. Probably need to check the ip packets comming from the phone to see what it is sending out. Is that what you did or is the sniffer at the other end.
sebjepb said:
Hi
Yes I have had the same issue with both the wizard and now hermes tried wm5 and wm6. I think it maybe related to NAT-T translation as am unsure from my reading weather MS supports NAT-T on the mobile end. If data session is being NATed by your provider then this may be the cause. Probably need to check the ip packets comming from the phone to see what it is sending out. Is that what you did or is the sniffer at the other end.
Click to expand...
Click to collapse
It has nothing to do with NAT traversal. WM5 (and WM6 probably?) does NOT support NAT-T, however I am not attempting to get this working over NAT. As I said I have a put a sniffer on the Ethernet port my Wireless AP is connected to and my Wizard does not transmit anything when configured for L2TP/IPSec (except a DNS lookup for the VPN server name if I enter it's DNS name as opposed to it's IP address). With PPTP it works and I can happily see the packets it transmits on the sniffer.
This is really frustrating as it looks like no one has ever got this to work
I had a HP iPAQ 6365 previously with Windows Mobile 2003 and I managed to get it working on this quite easily
Andy
Andy
I now have this working on both the wizard and the hermes.
I am a bit confused with your last response as ipsec port 4500 is nat-t and is required and is being transmitted by both the wizard and hermes in my case.
My setup maybe somewhat different to yours as I have a windows sbs2003 server running isa and rras. It is sitting behind an adsl modem router connected to the internet. The data connection on my phone is edge network on the wizard and HSDPA on the Hermes. Also have tried this via WiFi as well.
Steps I used
On server side router
On adsl modem router setup forwarding udp ports 500 ipsec, 4500 nat-t and 1701 l2tp and protocol 50 IPsec ESP. I selected l2tp/ipsec from its predefined list but noticed it missed udp 1701 so added this manually.
On Server.
ISA management selected Network Configuration right click and selected Allow vpn connections. This essentially setups the ip filters to allow incomming protocols and then sets up rras for pptp and l2tp ports.
In rras configure a preshared key by right click server/properties/security tick allow custome ipsec policy... and added preshared key.
On mobile
settings/connections
My Work Network
Edit my vpn servers and added new IPsec/L2TP connection.
Works a treat hope this helps
I did notice on another forum something about disabling the phone skin but I did not have to do this.
Regards
Stephen
sebjepb said:
Andy
I now have this working on both the wizard and the hermes.
I am a bit confused with your last response as ipsec port 4500 is nat-t and is required and is being transmitted by both the wizard and hermes in my case.
My setup maybe somewhat different to yours as I have a windows sbs2003 server running isa and rras. It is sitting behind an adsl modem router connected to the internet. The data connection on my phone is edge network on the wizard and HSDPA on the Hermes. Also have tried this via WiFi as well.
Steps I used
On server side router
On adsl modem router setup forwarding udp ports 500 ipsec, 4500 nat-t and 1701 l2tp and protocol 50 IPsec ESP. I selected l2tp/ipsec from its predefined list but noticed it missed udp 1701 so added this manually.
On Server.
ISA management selected Network Configuration right click and selected Allow vpn connections. This essentially setups the ip filters to allow incomming protocols and then sets up rras for pptp and l2tp ports.
In rras configure a preshared key by right click server/properties/security tick allow custome ipsec policy... and added preshared key.
On mobile
settings/connections
My Work Network
Edit my vpn servers and added new IPsec/L2TP connection.
Works a treat hope this helps
I did notice on another forum something about disabling the phone skin but I did not have to do this.
Regards
Stephen
Click to expand...
Click to collapse
What ROM are you running on the Wizard? I am currently running a WM6 ROM but I previously used the official QTEK update (AKU 2.3 I think?) and then various WM5 AKU 3.3 ROMs. I have tested this with all of them and none have worked. If I could just see it attempt to connect I would be happy The fact is it doesn't transmit anything at all and all I see is the dialogue box on the Wizard saying 'Cannot Connect'....
With regards to NAT-T I read that the VPN Client in Windows Mobile 5 was not capable of this, I could be wrong however?
Andy
Sorry didn't have signature updated I'm running WM6 MBE on the wizard and WM6 Black on the Hermes
Ok I am still confused can you tell me exactly how you are connecting to your work network. Wifi or gprs.
Can you check also.
Under settings/connections/advanced/select networks make sure you have a separate ie different connections for the internet and private network. The Intenet settings will be your service provider grps settings.
For the private network mine is set as My Work Network. Edit this and make sure sure you do not have any modem connection listed ie we want to make sure it goes out over our existing connection and does not try to make a new connection. Make sure the vpn tab has your vpn settings as required they must be listed here and not under the Internet connection.
If you are using WiFi you must make sure the network setup is Connects to: The Internet and not set to Work. If it is work the VPN will not connect. You can not change this on the fly need to disconnect and setup again.
PM Me When you get to work given time diff I should be home. Might be able to test connection to my server at home then can check logs etc
Also use Task manger v2.7 to view netsats on phone to confirm udp ports and ip routes etc. It will show you if the phone is indeed sending should see upd ports 500 4500 and 1701 being used.
Stephen
sebjepb said:
Sorry didn't have signature updated I'm running WM6 MBE on the wizard and WM6 Black on the Hermes
Ok I am still confused can you tell me exactly how you are connecting to your work network. Wifi or gprs.
Can you check also.
Under settings/connections/advanced/select networks make sure you have a separate ie different connections for the internet and private network. The Intenet settings will be your service provider grps settings.
For the private network mine is set as My Work Network. Edit this and make sure sure you do not have any modem connection listed ie we want to make sure it goes out over our existing connection and does not try to make a new connection. Make sure the vpn tab has your vpn settings as required they must be listed here and not under the Internet connection.
If you are using WiFi you must make sure the network setup is Connects to: The Internet and not set to Work. If it is work the VPN will not connect. You can not change this on the fly need to disconnect and setup again.
PM Me When you get to work given time diff I should be home. Might be able to test connection to my server at home then can check logs etc
Also use Task manger v2.7 to view netsats on phone to confirm udp ports and ip routes etc. It will show you if the phone is indeed sending should see upd ports 500 4500 and 1701 being used.
Stephen
Click to expand...
Click to collapse
I am using WiFi, this is all in a test environment so I have full control over everything. Under Connections I have 'My ISP' and 'My Work Network' listed. 'My ISP' has a modem entry, 'My Work Network' has no modem but has a VPN listed with the IP Address of the VPN server and set to L2TP/IPSec using a certificate on the device (I have tried with pre-shared key also). The WiFi entry is configured as 'Connects to The Internet'.
I enable the WiFi and verify I have connectivity, I then go to Connections, click on My Work Network, 'Manage existing connections' select the VPN tab, hold down the stylus on the entry and click connect and I almost immediately get the dialogue box saying 'cannot connect'. If I edit the VPN entry so it is PPTP it works every time. As I said I have a sniffer on so I can see what the Wizard transmits and it when set to L2TP/IPSec it doesnt transmit anything whatsoever, with PPTP I can capture the whole conversation.
Thanks for any help you can give me.
Andy
Ok I have now also tried using certificates and your right it does not seem to sending any info at all. It might ahve something to do with checking the certificate store first I ahve had issues before with Cisco vpn and certificates you have to get the nameing and certification justs right before it even starts the connection.
So first thing lets try pre shared keys as I have got that working. I will PM you my server details if you wish to try that first.
Stephen
sebjepb said:
Ok I have now also tried using certificates and your right it does not seem to sending any info at all. It might ahve something to do with checking the certificate store first I ahve had issues before with Cisco vpn and certificates you have to get the nameing and certification justs right before it even starts the connection.
So first thing lets try pre shared keys as I have got that working. I will PM you my server details if you wish to try that first.
Stephen
Click to expand...
Click to collapse
I have just re-tested this and using a pre-shared key - same result
There is a brief flash of 'connecting' when you click connect but then the 'Cannot Connect' dialogue box appears, nothing gets transmitted. I have tried entering different IP addresses (public, private etc) just to see if it will transmit anything - it doesn't regardless of the IP address I enter.....
Andy
Andy
check your pm
Are you sure the wireless ap is actually passing the ipsec/l2tp traffic.
Working, well sort of.....
After a lot of messing around I now have this working, at least partially........
Following a soft-reset I can connect to a Wireless network OK (either a new one or one that is pre-configured), I can then connect the VPN using L2TP/IPSec. I can also manually disconnect the VPN and re-connect without any issues. However, when the wireless is disconnected (i.e. turned off from CommManager) and then re-connected the VPN will never work again, unless the Wizard is soft-reset.
Does anyone know what is likely to be causing this? some application in memory or a registry 'state' entry
Does anyone else see this behaviour?
Andy
I had exactly this with L2TP/IPSec on the MDA Vario II, but the same settings work as they should on my Athena.
ADB100 said:
After a lot of messing around I now have this working, at least partially........
Following a soft-reset I can connect to a Wireless network OK (either a new one or one that is pre-configured), I can then connect the VPN using L2TP/IPSec. I can also manually disconnect the VPN and re-connect without any issues. However, when the wireless is disconnected (i.e. turned off from CommManager) and then re-connected the VPN will never work again, unless the Wizard is soft-reset.
Does anyone know what is likely to be causing this? some application in memory or a registry 'state' entry
Does anyone else see this behaviour?
Andy
Click to expand...
Click to collapse
HI!
How can you DISCONNECT?? Do you get a "Disconnect" button or menu item somewhere??
How do you know you are connected to VPN?
Thank you,
Dmitry.
A bit late but...
I have a possible solution to the fact it doesn't send ANY traffic on a connect attempt - on my XDA mini S (HTC Wizard) it requires me to put something in the 'domain' field on the username/pwd screen before it will start the IPSec negotiation....
Now I just have to get it o complete the process with the sonicwall...
David
Revisiting this
I can't get PPTP going on my HD2. Thoughts?
bumping this message
I have tried all the usual vpn software (for 3g connectivity) the only third party software that connects is the ncp software, but I get stuck because it wont accept a challenge response grid.
Symantic - won't auth
Green something - doesn't connect
MS VPN - doesn't connect
I have been able to connect in the past with an iPhone, but without a java i can't connect to most motorola hardware devices at work so it's useless. I'm testing a G1 on 1.6 now and it fails to connect also. Going to try openvpn today sometime. MY friend has his Eris working, so I know droid OS works.
I work for a large company and switching vpn hardware is out of the question, so if anyone has a 3g resolution for winmo, I won't have to trade my HD2.
Hi,
L2TR VPN with the Windows Mobile is working !!
The trick with L2TR VPN on WM is to use: a IP address (and NOT a hostname)
Strange, because using a hostname with PPTP VPN on the Windows Mobile it works.
With the trick L2TR works perfectly.
Chris
Hello. This is my first foray into VPN on Win Mo. I can establish a PPTP connection between my Imagio (stock Win Mo 6.5 R1) and my SBS 2008 server. I can ping the server and can browse the company web page. But I am having no luck accessing file shares. I have Schaps Network Plugin installed, but it doesn't see/can't access the shares. Will switching to IpSec VPN work? If so, any guidance on how to set it up on SBS 2008.
Hi,
I don't think this is currently possible but I do not see any reason why? Does anyone know if there is a 3rd party app to provide this?
Thanks,
Phillip
Possible ! (Well somewhat)
This is very much possible. I got it working as follows :
(1) Create a WiFi connection on Pocket Pc with ad-hoc feature and Open Security, make sure you select "Work" as the connection.
(2) Give the WiFi adapter on Pocket PC an internal address similar to 192.168.0.2 (255.255.255.0)
(3) On your PC/Laptop set WiFi adapter IP to 192.168.0.1 (255.255.255.0)
(4) You need a program like Pocket PC Proxy to be installed on the Pocket PC.
(5) Enable proxy settings on Laptop as 192.168.0.2:80 (or the port set on the proxy prog on ppc)
(6) Enable WiFi on ppc
And Voila ! You can browse internet using the connection on your ppc.
Hi,
Thanks, I will give this a try. However, I can't seem to find this piece of software (Pocket PC Proxy). Can you point me in the right direction?
Thanks
Here you go...
Thanks for the download, I'm using an HTC Touch (Elf) with WM6. I can't seem to figure out how to create an ad-hoc wifi connection?
(Sorry to be a pain but i think that this will benefit others too!)
Ahaa, I managed to figure out how to create an adhoc network on the Pocket PC, I assigned it the correct IP (as above) and basically followed the instructions.
I'm actually trying to get my iPod Touch to connect to the net via the HTC Touch.
I iPod sees the wifi connection and connects perfectly, I can even assign the ip and subnet mask. However, I simply can not connect to the internet either with or without the proxy. Any suggestions on what I am missing?
THanks
What kind of an internet connection do you have on the ppc ?
- GPRS/EDGE ? Is it always connected/on ?
Got it working, you can ignore the following
Thanks!
------
Hi, here is everything I have done:
Connections, Internet
Modem: T-Mobile Internet, GPRS (UK, no edge)
Proxy Settings: This network connects to the internet
This network uses a proxy server to conncet to the internet
149.254.291.132
(This was all set by the phone when I switched it on)
My Work Connection:
Nothing set up here
WIFI
Add New...
Network Name: test
Connects to: Work
This is a device-to-device (ad-hoc) connection
Authentication: Open
Data Encryption: Disabled
This seems to create an ad-hoc connection and sits there with 'Connecting' until another device connects to it.
Network Adapters
My network card connects to: Work
IEEE 802.11b/g Compatible WIFI....
Edit:
Use specific IP address:
192.168.0.2
255.255.255.0
(Everything else blank)
Wireless LAN
SSID: test
Mode: 802.11 Ad hoc
Channel: 11
When I connect two devices together the IP shown under advanced seems to read 192.168.0.21 (I think this should end .2 so not sure why it isn't)
If I connect my laptop I can 'ping' 192.168.0.2 and that works but both my laptop and ipod touch do not seem to be able to connect to the internet.
On the ipod touch I simply get 'Server not found' or something similar.
(I have remembered to run PocketPCProxy)
Yes, the GPRS is connected whenever I run PocketPCProxy.
I would really appreciate any help you can give, I really like using the browser on my ipod Touch but don't really want to go the whole hog and buy an iPhone because it is so tied down and restricted.
Thanks,
Phillip
I don't know what I have done but suddenly it works, now it comes up and shows the correct ip on my pocket pc.
Anyway, thanks for your help!
Hi everyone,
I have been trying to ad-hoc connect my PC (Lenovo X60s with XPSP2) to HTC Touch via WiFi to be able to share files and stream music.
It did connect and pinged ok, however the two just refuse to see one another on their networks.
Does anyone have any successful experience trying for the same?
Regards,
Madana
I tried this between my TyTN and TyTN II, the latter being the gateway, but the TyTN insists on still using GPRS for its internet instead of the wifi. Very annoying, and it's runing WM5 so (i dont think) you can't turn of the GPRS like you can with WM6.
Does anyone know how to make it use wifi, and wifi only for internet?
Thanks,
Sebastian
i have installed pocket pc proxy after a file called ......ppc3.arm.cab (i don't remember how it begins) but it doesn't work... any idea?
same here the pocket pc proxy when i run shows a fatal error in running it.
what should we do??
Hello,
I have samsung c6712 with wifi connected with internet near internet company with router as it is free for me, setting and pasaword is setted by those guys on my phone but they didnot give me their password and settings.
i like to run/use internet on my pc (xp32) with cable connection. How can I use that
[email protected]
Hi,
I am trying unsuccessfully to connect to a PPTP VPN using the VPN client built into my new HTC TyTN II.
Wifi - I can connect using a WinXP SP2 laptop using wifi through my home linksys wireless router (which has PPTP passthrough enabled) using the standard Win XP vpn client. When I try with my TyTN II, I can browse ok but if I set up a VPN connection I get "VPN server problems. Verify your username and password, etc"
GPRS - If I try to connect over GPRS, I connect to Orange GPRS but when it tries to connect to the IP address of my VPN server, I get the same VPN server problem error message. (As a side issue, I asked Orange to enable my account for vpn which they did, sent a SIM update and told me to change my apn to 'internetvpn' instead of 'orangeinternet')
As I can connect through my wifi connected laptop, it seems to point to my WM6 vpn client but my forum searches suggest that the WM6 client works ok. Oh, and yes, I have checked that I am using the correct vpn username and password!
Any thoughts greatly appreciated - the ability to maintain some linux servers was my main reason for getting this phone!
_______________________________________________________
Phone - HTC TyTN from Orange
Windows Mobile 6 Professional
CE OS 5.2.1620 (Build 18125.0.4.2)
Processor QUALCOMM MSM7200-400MHz
Memory 101.63MB
Setings Device Information Version
Operator version 24.181.1.612
ROM Version 1.81.61.2.WWE
ROM Date 09/20/07
Radio version 1.27.14.32
Protocol version 22.45.88.07H
Bump!!! Same problem here. I have all the proper ports open on my router and still no luck.
I've been trying to resolve this with the people that manage my vpn server which is my case is a Watchguard firewall - apparantly Watchguard isn't compatable with PPTP on WM6 and they have suggested using IPSec and have provided me with a client (not that I've got that working yet either!)
I suggest you contact the vendor of your vpn server and ask them whether they are compatable and how a WM6 client should be configured. Post anything you find out here for the benefit of others.
WM6 don't connect to VPN over GPRS/ WiFi
Friends...
I have the same problem... the VPN server is Windows Server 2003... My PDA has WM6 (with in-build VPN client)... then VPN PPTP would work OK... but What is the wrong??
Regards...
I also could not connect on vpn over GPRS and got error message, but after I tested all installed programs I have found out that my SPB GPRS Monitor was the reason for the errors. So I killed it.
Now VPN over GPRS connects and looking into register I see that I am really connected i.e. I got DNS server IP, I got name of the local network and dynamic IP for my HTC, but nothing works. As I have found out from server guys they see me but my dynamic IP is not logged in server DNS, so no program sees me and I can not work.
Can somebody help?
Same
I have a similar problem but the difference is that i don't even receive an error message. When i click connect NOTHING happens!! The wifi i am using is an open network but I must connect to vpn to connect to the internet.
Please help as i really need to get this working...
I have been trying to iron this out with IT at my office as well. I have been trying to get WM6.1 VPN working for nearly a year.
I have a TyTnII and my IT office just bought some kind of WM6.1 Motorola/Sprint Smartphone as well which they actually asked me about setting up for them.
The problem what I am experiencing is that I CAN connect to the VPN server (I use one of the TaskMan progs that has ipconfig built it, and I am getting an appropriate IP from the VPN server). BUT I can't browse ANY intranet sites via PIE or Opera Mobile 9.5. Whenever I try to browse to an intranet site I just get nothing, browser does nothing for ~10min then gives timeout error.
I have heard that this has to do with an inbuilt error in the PPTP module of the VPN client that incorrectly makes VPN server requests using the IP address assigned by the GPRS/EDGE/3G/etc. connection rather than the IP address assigned by the VPN connection, obviously will cause problems!
Anyway, we are investigating 3rd part VPN clients...
Only IPSEC works
I also made many tries to get vpn working over BT PAN profile.
The only configuration which worked for my was IPSEC with the Safenet SoftRemote-LT Client on PC.
With the windows native pptp based vpn does not work .
I got the error code 721 what means that the GRE protocol (frame type 47 on port 1721) does not pass through. This seems to be the the real problem of the packet filtering components of the WM device. The problem is not related to bluetooth or PAN Driver, because it behaves in the same way if you try to do it over USB port. No way.
You guys might want to check out my post about getting my PPTP VPN working and actually syncing ActiveSync on a fixed schedule regularly over VPN.
http://forum.xda-developers.com/showthread.php?t=428878
Getting what you want to work over VPN requires work URL Exceptions so that the traffice is properly routed.
nkitson said:
I've been trying to resolve this with the people that manage my vpn server which is my case is a Watchguard firewall - apparantly Watchguard isn't compatable with PPTP on WM6 and they have suggested using IPSec and have provided me with a client (not that I've got that working yet either!)
I suggest you contact the vendor of your vpn server and ask them whether they are compatable and how a WM6 client should be configured. Post anything you find out here for the benefit of others.
Click to expand...
Click to collapse
Watchguard does support PPTP, your IT guys just need to configure it. As for IPSec which would be awesome because there is an app call Greenbow that will connect you over 3G doesn't work with Watchguard. You can only connect using their own client for it which needs a license and isn't support on Windows Mobile. They got a hate email from me for that crap.
At school we have WIFI and a week of him trying to get my i900 Omnia WM 6.1 I tried the WM 6.5 and nothing. Classmates in class WiFi is not around and I am doing something wrong. I've set up your Wifi in this guide http://forum.xda-developers.com/showthread.php?p=4107978 wondering if I would help set yet
Network Adapters
NDISWAN Miniport L2TP
PPTP NDISWAN Miniport
Sychip Jaguar WLAN GSPI Card
...
...
http://img3.imageshack.us/img3/9509/100104131209.jpg
PS: Wireless manager telling me he connected but when I run Opera Mobile or Internet Explorer so I do not load page and write something DNS
Please help me.
Perhaps the school has a school has a certificate that needs to be accepted prior to browsing the web. I was having this issue yesterday and it was driving me crazy. I tried multiple builds of Opera, changing security settings, etc. Finally I used NFSFAN's 16xxx Opera build and the certificate was finally displayed so that I could accept it and browse on WiFi. I have not done a line-by-line comparison of NFSFAN's settings vs other builds, but I know that his worked to fix my issue. Hope that I understood your dilemma accordingly and that this helps.